+// SPDX-License-Identifier: GPL-2.0+
/*
* SAMSUNG EXYNOS5 USB HOST XHCI Controller
*
* Copyright (C) 2012 Samsung Electronics Co.Ltd
* Vivek Gautam <gautam.vivek@samsung.com>
* Vikas Sajjan <vikas.sajjan@samsung.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
#include <common.h>
#include <dm.h>
#include <fdtdec.h>
-#include <libfdt.h>
+#include <log.h>
+#include <linux/delay.h>
+#include <linux/libfdt.h>
#include <malloc.h>
#include <usb.h>
#include <watchdog.h>
#include <asm/arch/power.h>
#include <asm/arch/xhci-exynos.h>
#include <asm/gpio.h>
-#include <asm-generic/errno.h>
+#include <linux/errno.h>
#include <linux/compat.h>
#include <linux/usb/dwc3.h>
-#include "xhci.h"
+#include <usb/xhci.h>
/* Declare global data pointer */
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_DM_USB
struct exynos_xhci_platdata {
fdt_addr_t hcd_base;
fdt_addr_t phy_base;
struct gpio_desc vbus_gpio;
};
-#endif
/**
* Contains pointers to register base addresses
* for the usb controller.
*/
struct exynos_xhci {
-#ifdef CONFIG_DM_USB
struct usb_platdata usb_plat;
-#endif
struct xhci_ctrl ctrl;
struct exynos_usb3_phy *usb3_phy;
struct xhci_hccr *hcd;
struct dwc3 *dwc3_reg;
-#ifndef CONFIG_DM_USB
- struct gpio_desc vbus_gpio;
-#endif
};
-#ifndef CONFIG_DM_USB
-static struct exynos_xhci exynos;
-#endif
-
-#ifdef CONFIG_DM_USB
static int xhci_usb_ofdata_to_platdata(struct udevice *dev)
{
struct exynos_xhci_platdata *plat = dev_get_platdata(dev);
/*
* Get the base address for XHCI controller from the device node
*/
- plat->hcd_base = fdtdec_get_addr(blob, dev->of_offset, "reg");
+ plat->hcd_base = devfdt_get_addr(dev);
if (plat->hcd_base == FDT_ADDR_T_NONE) {
debug("Can't get the XHCI register base address\n");
return -ENXIO;
}
depth = 0;
- node = fdtdec_next_compatible_subnode(blob, dev->of_offset,
+ node = fdtdec_next_compatible_subnode(blob, dev_of_offset(dev),
COMPAT_SAMSUNG_EXYNOS5_USB3_PHY, &depth);
if (node <= 0) {
debug("XHCI: Can't get device node for usb3-phy controller\n");
return 0;
}
-#else
-static int exynos_usb3_parse_dt(const void *blob, struct exynos_xhci *exynos)
-{
- fdt_addr_t addr;
- unsigned int node;
- int depth;
-
- node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_XHCI);
- if (node <= 0) {
- debug("XHCI: Can't get device node for xhci\n");
- return -ENODEV;
- }
-
- /*
- * Get the base address for XHCI controller from the device node
- */
- addr = fdtdec_get_addr(blob, node, "reg");
- if (addr == FDT_ADDR_T_NONE) {
- debug("Can't get the XHCI register base address\n");
- return -ENXIO;
- }
- exynos->hcd = (struct xhci_hccr *)addr;
-
- /* Vbus gpio */
- gpio_request_by_name_nodev(blob, node, "samsung,vbus-gpio", 0,
- &exynos->vbus_gpio, GPIOD_IS_OUT);
-
- depth = 0;
- node = fdtdec_next_compatible_subnode(blob, node,
- COMPAT_SAMSUNG_EXYNOS5_USB3_PHY, &depth);
- if (node <= 0) {
- debug("XHCI: Can't get device node for usb3-phy controller\n");
- return -ENODEV;
- }
-
- /*
- * Get the base address for usbphy from the device node
- */
- exynos->usb3_phy = (struct exynos_usb3_phy *)fdtdec_get_addr(blob, node,
- "reg");
- if (exynos->usb3_phy == NULL) {
- debug("Can't get the usbphy register address\n");
- return -ENXIO;
- }
-
- return 0;
-}
-#endif
static void exynos5_usb3_phy_init(struct exynos_usb3_phy *phy)
{
set_usbdrd_phy_ctrl(POWER_USB_DRD_PHY_CTRL_DISABLE);
}
-static void dwc3_set_mode(struct dwc3 *dwc3_reg, u32 mode)
-{
- clrsetbits_le32(&dwc3_reg->g_ctl,
- DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG),
- DWC3_GCTL_PRTCAPDIR(mode));
-}
-
-static void dwc3_core_soft_reset(struct dwc3 *dwc3_reg)
-{
- /* Before Resetting PHY, put Core in Reset */
- setbits_le32(&dwc3_reg->g_ctl,
- DWC3_GCTL_CORESOFTRESET);
-
- /* Assert USB3 PHY reset */
- setbits_le32(&dwc3_reg->g_usb3pipectl[0],
- DWC3_GUSB3PIPECTL_PHYSOFTRST);
-
- /* Assert USB2 PHY reset */
- setbits_le32(&dwc3_reg->g_usb2phycfg,
- DWC3_GUSB2PHYCFG_PHYSOFTRST);
-
- mdelay(100);
-
- /* Clear USB3 PHY reset */
- clrbits_le32(&dwc3_reg->g_usb3pipectl[0],
- DWC3_GUSB3PIPECTL_PHYSOFTRST);
-
- /* Clear USB2 PHY reset */
- clrbits_le32(&dwc3_reg->g_usb2phycfg,
- DWC3_GUSB2PHYCFG_PHYSOFTRST);
-
- /* After PHYs are stable we can take Core out of reset state */
- clrbits_le32(&dwc3_reg->g_ctl,
- DWC3_GCTL_CORESOFTRESET);
-}
-
-static int dwc3_core_init(struct dwc3 *dwc3_reg)
-{
- u32 reg;
- u32 revision;
- unsigned int dwc3_hwparams1;
-
- revision = readl(&dwc3_reg->g_snpsid);
- /* This should read as U3 followed by revision number */
- if ((revision & DWC3_GSNPSID_MASK) != 0x55330000) {
- puts("this is not a DesignWare USB3 DRD Core\n");
- return -EINVAL;
- }
-
- dwc3_core_soft_reset(dwc3_reg);
-
- dwc3_hwparams1 = readl(&dwc3_reg->g_hwparams1);
-
- reg = readl(&dwc3_reg->g_ctl);
- reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
- reg &= ~DWC3_GCTL_DISSCRAMBLE;
- switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc3_hwparams1)) {
- case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
- reg &= ~DWC3_GCTL_DSBLCLKGTNG;
- break;
- default:
- debug("No power optimization available\n");
- }
-
- /*
- * WORKAROUND: DWC3 revisions <1.90a have a bug
- * where the device can fail to connect at SuperSpeed
- * and falls back to high-speed mode which causes
- * the device to enter a Connect/Disconnect loop
- */
- if ((revision & DWC3_REVISION_MASK) < 0x190a)
- reg |= DWC3_GCTL_U2RSTECN;
-
- writel(reg, &dwc3_reg->g_ctl);
-
- return 0;
-}
-
static int exynos_xhci_core_init(struct exynos_xhci *exynos)
{
int ret;
exynos5_usb3_phy_exit(exynos->usb3_phy);
}
-#ifndef CONFIG_DM_USB
-int xhci_hcd_init(int index, struct xhci_hccr **hccr, struct xhci_hcor **hcor)
-{
- struct exynos_xhci *ctx = &exynos;
- int ret;
-
-#ifdef CONFIG_OF_CONTROL
- exynos_usb3_parse_dt(gd->fdt_blob, ctx);
-#else
- ctx->usb3_phy = (struct exynos_usb3_phy *)samsung_get_base_usb3_phy();
- ctx->hcd = (struct xhci_hccr *)samsung_get_base_usb_xhci();
-#endif
-
- ctx->dwc3_reg = (struct dwc3 *)((char *)(ctx->hcd) + DWC3_REG_OFFSET);
-
-#ifdef CONFIG_OF_CONTROL
- /* setup the Vbus gpio here */
- if (dm_gpio_is_valid(&ctx->vbus_gpio))
- dm_gpio_set_value(&ctx->vbus_gpio, 1);
-#endif
-
- ret = exynos_xhci_core_init(ctx);
- if (ret) {
- puts("XHCI: failed to initialize controller\n");
- return -EINVAL;
- }
-
- *hccr = (ctx->hcd);
- *hcor = (struct xhci_hcor *)((uint32_t) *hccr
- + HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
-
- debug("Exynos5-xhci: init hccr %x and hcor %x hc_length %d\n",
- (uint32_t)*hccr, (uint32_t)*hcor,
- (uint32_t)HC_LENGTH(xhci_readl(&(*hccr)->cr_capbase)));
-
- return 0;
-}
-
-void xhci_hcd_stop(int index)
-{
- struct exynos_xhci *ctx = &exynos;
-
- exynos_xhci_core_exit(ctx);
-}
-#endif
-
-#ifdef CONFIG_DM_USB
static int xhci_usb_probe(struct udevice *dev)
{
struct exynos_xhci_platdata *plat = dev_get_platdata(dev);
.priv_auto_alloc_size = sizeof(struct exynos_xhci),
.flags = DM_FLAG_ALLOC_PRIV_DMA,
};
-#endif
projects / oweals / u-boot.git / blobdiff