Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq

[oweals/u-boot.git] / drivers / sysreset / Kconfig

diff --git a/drivers/sysreset/Kconfig b/drivers/sysreset/Kconfig
index 8ce3e2e20761e55f25b924c97004fdf413a2383b..4be7433404701d9943c50f202b43a593e330489d 100644 (file)
--- a/drivers/sysreset/Kconfig
+++ b/drivers/sysreset/Kconfig
@@ -13,11 +13,39 @@ config SYSRESET
          to effect a reset. The uclass will try all available drivers when
          reset_walk() is called.
 
+config SPL_SYSRESET
+       bool "Enable support for system reset drivers in SPL mode"
+       depends on SYSRESET && SPL_DM
+       help
+         Enable system reset drivers which can be used to reset the CPU or
+         board. Each driver can provide a reset method which will be called
+         to effect a reset. The uclass will try all available drivers when
+         reset_walk() is called.
+
+config TPL_SYSRESET
+       bool "Enable support for system reset drivers in TPL mode"
+       depends on SYSRESET && TPL_DM
+       help
+         Enable system reset drivers which can be used to reset the CPU or
+         board. Each driver can provide a reset method which will be called
+         to effect a reset. The uclass will try all available drivers when
+         reset_walk() is called.
+
 if SYSRESET
 
+if CMD_POWEROFF
+
+config SYSRESET_CMD_POWEROFF
+       bool "sysreset implementation of the poweroff command"
+       help
+         This should be selected by the appropriate PMIC driver if
+         the poweroff command is enabled.
+
+endif
+
 config SYSRESET_GPIO
        bool "Enable support for GPIO reset driver"
-       select GPIO
+       select DM_GPIO
        help
          Reset support via GPIO pin connected reset logic. This is used for
          example on Microblaze where reset logic can be controlled via GPIO
@@ -32,10 +60,25 @@ config SYSRESET_MICROBLAZE
 config SYSRESET_PSCI
        bool "Enable support for PSCI System Reset"
        depends on ARM_PSCI_FW
+       select SPL_ARM_PSCI_FW if SPL
        help
          Enable PSCI SYSTEM_RESET function call.  To use this, PSCI firmware
          must be running on your system.
 
+config SYSRESET_SOCFPGA
+       bool "Enable support for Intel SOCFPGA family"
+       depends on ARCH_SOCFPGA && (TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10)
+       help
+         This enables the system reset driver support for Intel SOCFPGA SoCs
+         (Cyclone 5, Arria 5 and Arria 10).
+
+config SYSRESET_SOCFPGA_S10
+       bool "Enable support for Intel SOCFPGA Stratix 10"
+       depends on ARCH_SOCFPGA && TARGET_SOCFPGA_STRATIX10
+       help
+         This enables the system reset driver support for Intel SOCFPGA
+         Stratix SoCs.
+
 config SYSRESET_TI_SCI
        bool "TI System Control Interface (TI SCI) system reset driver"
        depends on TI_SCI_PROTOCOL
@@ -58,13 +101,31 @@ config SYSRESET_WATCHDOG
        help
          Reboot support for generic watchdog reset.
 
+config SYSRESET_RESETCTL
+       bool "Enable support for reset controller reboot driver"
+       select DM_RESET
+       help
+         Reboot support using generic reset controller.
+
 config SYSRESET_X86
        bool "Enable support for x86 processor reboot driver"
        depends on X86
        help
          Reboot support for generic x86 processor reset.
 
-config SYSRESET_MCP83XX
+config SYSRESET_SPL_X86
+       bool "Enable support for x86 processor reboot driver in SPL"
+       depends on X86
+       help
+         Reboot support for generic x86 processor reset in SPL.
+
+config SYSRESET_TPL_X86
+       bool "Enable support for x86 processor reboot driver in TPL"
+       depends on X86
+       help
+         Reboot support for generic x86 processor reset in TPL.
+
+config SYSRESET_MPC83XX
        bool "Enable support MPC83xx SoC family reboot driver"
        help
          Reboot support for NXP MPC83xx SoCs.