choice
prompt "Boot count device"
default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX
+ default BOOTCOUNT_AT91 if AT91SAM9XE
+ default BOOTCOUNT_GENERIC
+
+config BOOTCOUNT_GENERIC
+ bool "Generic default boot counter"
+ help
+ Generic bootcount stored at SYS_BOOTCOUNT_ADDR.
+
+ SYS_BOOTCOUNT_ADDR:
+ Set to the address where the bootcount and bootcount magic
+ will be stored.
config BOOTCOUNT_EXT
bool "Boot counter on EXT filesystem"
+ depends on FS_EXT4
+ select EXT4_WRITE
help
Add support for maintaining boot count in a file on an EXT
filesystem.
config BOOTCOUNT_AM33XX
bool "Boot counter in AM33XX RTC IP block"
depends on AM33XX || SOC_DA8XX
+ select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX
help
A bootcount driver for the RTC IP block found on many TI platforms.
This requires the RTC clocks, etc, to be enabled prior to use and
So the Userspace Application must set the "upgrade_available"
and "bootcount" variable to 0, if a boot was successfully.
+config BOOTCOUNT_RAM
+ bool "Boot counter in RAM"
+ help
+ Store the bootcount in DRAM protected against against bit errors
+ due to short power loss or holding a system in RESET.
+
+config BOOTCOUNT_I2C
+ bool "Boot counter on I2C device"
+ help
+ Enable support for the bootcounter on an i2c (like RTC) device.
+ CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
+ CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
+ the bootcounter.
+
+config BOOTCOUNT_AT91
+ bool "Boot counter for Atmel AT91SAM9XE"
+ depends on AT91SAM9XE
+
+config DM_BOOTCOUNT
+ bool "Boot counter in a device-model device"
+ help
+ Enables reading/writing the bootcount in a device-model based
+ backing store. If an entry in /chosen/u-boot,bootcount-device
+ exists, this will be the preferred bootcount device; otherwise
+ the first available bootcount device will be used.
+
endchoice
+if DM_BOOTCOUNT
+
+menu "Backing stores for device-model backed bootcount"
+config DM_BOOTCOUNT_RTC
+ bool "Support RTC devices as a backing store for bootcount"
+ depends on DM_RTC
+ help
+ Enabled reading/writing the bootcount in a DM RTC device.
+ The wrapper device is to be specified with the compatible string
+ 'u-boot,bootcount-rtc' and the 'rtc'-property (a phandle pointing
+ to the underlying RTC device) and an optional 'offset' property
+ are supported.
+
+ Accesses to the backing store are performed using the write16
+ and read16 ops of DM RTC devices.
+
+config DM_BOOTCOUNT_I2C_EEPROM
+ bool "Support i2c eeprom devices as a backing store for bootcount"
+ depends on I2C_EEPROM
+ help
+ Enabled reading/writing the bootcount in a DM i2c eeprom device.
+ The wrapper device is to be specified with the compatible string
+ 'u-boot,bootcount-i2c-eeprom' and the 'i2c-eeprom'-property (a phandle
+ pointing to the underlying i2c eeprom device) and an optional 'offset'
+ property are supported.
+
+config BOOTCOUNT_MEM
+ bool "Support memory based bootcounter"
+ help
+ Enabling Memory based bootcount, typically in a SoC register which
+ is not cleared on softreset.
+ compatible = "u-boot,bootcount";
+
+endmenu
+
+endif
+
+config BOOTCOUNT_BOOTLIMIT
+ int "Maximum number of reboot cycles allowed"
+ default 0
+ help
+ Set the Maximum number of reboot cycles allowed without the boot
+ counter being cleared.
+ If set to 0 do not set a boot limit in the environment.
+
+config BOOTCOUNT_ALEN
+ int "I2C address length"
+ default 1
+ depends on BOOTCOUNT_I2C
+ help
+ Length of the the I2C address at SYS_BOOTCOUNT_ADDR for storing
+ the boot counter.
+
config SYS_BOOTCOUNT_SINGLEWORD
bool "Use single word to pack boot count and magic value"
+ depends on BOOTCOUNT_GENERIC
help
This option enables packing boot count magic value and boot count
into single word (32 bits).
config SYS_BOOTCOUNT_ADDR
hex "RAM address used for reading and writing the boot counter"
- default 0x7000A000
- depends on BOOTCOUNT_EXT
+ default 0x44E3E000 if BOOTCOUNT_AM33XX
+ default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A
+ depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \
+ BOOTCOUNT_I2C
help
Set the address used for reading and writing the boot counter.
+config SYS_BOOTCOUNT_MAGIC
+ hex "Magic value for the boot counter"
+ default 0xB001C041
+ help
+ Set the magic value used for the boot counter.
+
endif