help
If you want to build SPL as well as the normal image, say Y.
-config SPL_BOARD_INIT
+if SPL
+
+config SPL_LDSCRIPT
+ string "Linker script for the SPL stage"
+ default "arch/$(ARCH)/cpu/u-boot-spl.lds"
depends on SPL
+ help
+ The SPL stage will usually require a different linker-script
+ (as it runs from a different memory region) than the regular
+ U-Boot stage. Set this to the path of the linker-script to
+ be used for SPL.
+
+config SPL_BOARD_INIT
bool "Call board-specific initialization in SPL"
help
If this option is enabled, U-Boot will call the function
spl_board_init() from board_init_r(). This function should be
provided by the board.
+config SPL_BOOTROM_SUPPORT
+ bool "Support returning to the BOOTROM"
+ help
+ Some platforms (e.g. the Rockchip RK3368) provide support in their
+ ROM for loading the next boot-stage after performing basic setup
+ from the SPL stage.
+
+ Enable this option, to return to the BOOTROM through the
+ BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
+ boot device list, if not implemented for a given board)
+
config SPL_RAW_IMAGE_SUPPORT
bool "Support SPL loading and booting of RAW images"
- depends on SPL
default n if (ARCH_MX6 && (SPL_MMC_SUPPORT || SPL_SATA_SUPPORT))
default y if !TI_SECURE_DEVICE
help
config SPL_SYS_MALLOC_SIMPLE
bool
- depends on SPL
prompt "Only use malloc_simple functions in the SPL"
help
Say Y here to only use the *_simple malloc functions from
this will make the SPL binary smaller at the cost of more heap
usage as the *_simple malloc functions do not re-use free-ed mem.
+config TPL_SYS_MALLOC_SIMPLE
+ bool
+ prompt "Only use malloc_simple functions in the TPL"
+ help
+ Say Y here to only use the *_simple malloc functions from
+ malloc_simple.c, rather then using the versions from dlmalloc.c;
+ this will make the TPL binary smaller at the cost of more heap
+ usage as the *_simple malloc functions do not re-use free-ed mem.
+
config SPL_STACK_R
- depends on SPL
bool "Enable SDRAM location for SPL stack"
help
SPL starts off execution in SRAM and thus typically has only a small
config SPL_STACK_R_ADDR
depends on SPL_STACK_R
hex "SDRAM location for SPL stack"
+ default 0x82000000 if ARCH_OMAP2PLUS
help
Specify the address in SDRAM for the SPL stack. This will be set up
before board_init_r() is called.
SRAM which is limited to SYS_MALLOC_F_LEN bytes.
config SPL_SEPARATE_BSS
- depends on SPL
bool "BSS section is in a different memory region from text"
help
Some platforms need a large BSS region in SPL and can provide this
location is used. Normally we put the device tree at the end of BSS
but with this option enabled, it goes at _image_binary_end.
+config SPL_DISABLE_BANNER_PRINT
+ bool "Disable output of the SPL banner 'U-Boot SPL ...'"
+ help
+ If this option is enabled, SPL will not print the banner with version
+ info. Selecting this option could be useful to reduce SPL boot time
+ (e.g. approx. 6 ms slower, when output on i.MX6 with 115200 baud).
+
config SPL_DISPLAY_PRINT
- depends on SPL
bool "Display a board-specific message in SPL"
help
If this option is enabled, U-Boot will call the function
config SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
bool "MMC raw mode: by sector"
- depends on SPL
default y if ARCH_SUNXI || ARCH_DAVINCI || ARCH_UNIPHIER ||ARCH_MX6 || \
ARCH_ROCKCHIP || ARCH_MVEBU || ARCH_SOCFPGA || \
ARCH_AT91 || ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || \
config SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
hex "Address on the MMC to load U-Boot from"
- depends on SPL && SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+ depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
default 0x50 if ARCH_SUNXI
default 0x75 if ARCH_DAVINCI
default 0x8a if ARCH_MX6
- default 0x100 if ARCH_ROCKCHIP || ARCH_UNIPHIER
+ default 0x100 if ARCH_UNIPHIER
default 0x140 if ARCH_MVEBU
default 0x200 if ARCH_SOCFPGA || ARCH_AT91
default 0x300 if ARCH_ZYNQ || ARCH_KEYSTONE || OMAP34XX || OMAP44XX || \
OMAP54XX || AM33XX || AM43XX
+ default 0x4000 if ARCH_ROCKCHIP
help
Address on the MMC to load U-Boot from, when the MMC is being used
in raw mode. Units: MMC sectors (1 sector = 512 bytes).
config SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
bool "MMC Raw mode: by partition"
- depends on SPL
help
Use a partition for loading U-Boot when using MMC/SD in raw mode.
config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
hex "Partition to use to load U-Boot from"
- depends on SPL && SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
+ depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
default 1
help
Partition on the MMC to load U-Boot from when the MMC is being
config SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
bool "MMC raw mode: by partition type"
- depends on SPL && DOS_PARTITION && \
- SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
+ depends on DOS_PARTITION && SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
help
Use partition type for specifying U-Boot partition on MMC/SD in
raw mode. U-Boot will be loaded from the first partition of this
config SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_TYPE
hex "Partition Type on the MMC to load U-Boot from"
- depends on SPL && SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
+ depends on SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
help
Partition Type on the MMC to load U-Boot from, when the MMC is being
used in raw mode.
-config TPL
- bool
- depends on SPL && SUPPORT_TPL
- prompt "Enable TPL"
- help
- If you want to build TPL as well as the normal image and SPL, say Y.
-
config SPL_CRC32_SUPPORT
bool "Support CRC32"
depends on SPL_FIT
SHA256 variant is supported: SHA512 and others are not currently
supported in U-Boot.
+config SPL_FIT_IMAGE_TINY
+ bool "Remove functionality from SPL FIT loading to reduce size"
+ depends on SPL_FIT
+ default y if MACH_SUN50I || MACH_SUN50I_H5
+ help
+ Enable this to reduce the size of the FIT image loading code
+ in SPL, if space for the SPL binary is very tight.
+
+ This removes the detection of image types (which forces the
+ first image to be treated as having a U-Boot style calling
+ convention) and skips the recording of each loaded payload
+ (i.e. loadable) into the FDT (modifying the loaded FDT to
+ ensure this information is available to the next image
+ invoked).
+
config SPL_CPU_SUPPORT
bool "Support CPU drivers"
- depends on SPL
help
Enable this to support CPU drivers in SPL. These drivers can set
up CPUs and provide information about them such as the model and
config SPL_CRYPTO_SUPPORT
bool "Support crypto drivers"
- depends on SPL
help
Enable crypto drivers in SPL. These drivers can be used to
accelerate secure boot processing in secure applications. Enable
bool "Support hashing drivers"
select SHA1
select SHA256
- depends on SPL
help
Enable hashing drivers in SPL. These drivers can be used to
accelerate secure boot processing in secure applications. Enable
config SPL_DMA_SUPPORT
bool "Support DMA drivers"
- depends on SPL
help
Enable DMA (direct-memory-access) drivers in SPL. These drivers
can be used to handle memory-to-peripheral data transfer without
config SPL_DRIVERS_MISC_SUPPORT
bool "Support misc drivers"
- depends on SPL
help
Enable miscellaneous drivers in SPL. These drivers perform various
tasks that don't fall nicely into other categories, Enable this
config SPL_ENV_SUPPORT
bool "Support an environment"
- depends on SPL
help
Enable environment support in SPL. The U-Boot environment provides
a number of settings (essentially name/value pairs) which can
needed in SPL as it has a much simpler task with less
configuration. But some boards use this to support 'Falcon' boot
on EXT2 and FAT, where SPL boots directly into Linux without
- starting U-Boot first. Enabling this option will make getenv()
- and setenv() available in SPL.
+ starting U-Boot first. Enabling this option will make env_get()
+ and env_set() available in SPL.
config SPL_SAVEENV
bool "Support save environment"
- depends on SPL && SPL_ENV_SUPPORT
+ depends on SPL_ENV_SUPPORT
+ select SPL_MMC_WRITE if ENV_IS_IN_MMC
help
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
config SPL_EXT_SUPPORT
bool "Support EXT filesystems"
- depends on SPL
help
Enable support for EXT2/3/4 filesystems with SPL. This permits
U-Boot (or Linux in Falcon mode) to be loaded from an EXT
config SPL_FAT_SUPPORT
bool "Support FAT filesystems"
- depends on SPL
+ select FS_FAT
help
Enable support for FAT and VFAT filesystems with SPL. This
permits U-Boot (or Linux in Falcon mode) to be loaded from a FAT
config SPL_FPGA_SUPPORT
bool "Support FPGAs"
- depends on SPL
help
Enable support for FPGAs in SPL. Field-programmable Gate Arrays
provide software-configurable hardware which is typically used to
config SPL_GPIO_SUPPORT
bool "Support GPIO"
- depends on SPL
help
Enable support for GPIOs (General-purpose Input/Output) in SPL.
GPIOs allow U-Boot to read the state of an input line (high or
config SPL_I2C_SUPPORT
bool "Support I2C"
- depends on SPL
help
Enable support for the I2C (Inter-Integrated Circuit) bus in SPL.
I2C works with a clock and data line which can be driven by a
config SPL_LIBCOMMON_SUPPORT
bool "Support common libraries"
- depends on SPL
help
Enable support for common U-Boot libraries within SPL. These
libraries include common code to deal with U-Boot images,
config SPL_LIBDISK_SUPPORT
bool "Support disk paritions"
- depends on SPL
help
Enable support for disk partitions within SPL. 'Disk' is something
of a misnomer as it includes non-spinning media such as flash (as
config SPL_LIBGENERIC_SUPPORT
bool "Support generic libraries"
- depends on SPL
help
Enable support for generic U-Boot libraries within SPL. These
libraries include generic code to deal with device tree, hashing,
config SPL_MMC_SUPPORT
bool "Support MMC"
- depends on SPL && MMC
+ depends on MMC
help
Enable support for MMC (Multimedia Card) within SPL. This enables
the MMC protocol implementation and allows any enabled drivers to
this option to build the drivers in drivers/mmc as part of an SPL
build.
+config SPL_MMC_WRITE
+ bool "MMC/SD/SDIO card support for write operations in SPL"
+ depends on SPL_MMC_SUPPORT
+ default n
+ help
+ Enable write access to MMC and SD Cards in SPL
+
+
config SPL_MPC8XXX_INIT_DDR_SUPPORT
bool "Support MPC8XXX DDR init"
- depends on SPL
help
Enable support for DDR-SDRAM (double-data-rate synchronous dynamic
random-access memory) on the MPC8XXX family within SPL. This
config SPL_MTD_SUPPORT
bool "Support MTD drivers"
- depends on SPL
help
Enable support for MTD (Memory Technology Device) within SPL. MTD
provides a block interface over raw NAND and can also be used with
config SPL_MUSB_NEW_SUPPORT
bool "Support new Mentor Graphics USB"
- depends on SPL
help
Enable support for Mentor Graphics USB in SPL. This is a new
driver used by some boards. Enable this option to build
config SPL_NAND_SUPPORT
bool "Support NAND flash"
- depends on SPL
help
Enable support for NAND (Negative AND) flash in SPL. NAND flash
can be used to allow SPL to load U-Boot from supported devices.
config SPL_NET_SUPPORT
bool "Support networking"
- depends on SPL
help
Enable support for network devices (such as Ethernet) in SPL.
This permits SPL to load U-Boot over a network link rather than
config SPL_NO_CPU_SUPPORT
bool "Drop CPU code in SPL"
- depends on SPL
help
This is specific to the ARM926EJ-S CPU. It disables the standard
start.S start-up code, presumably so that a replacement can be
config SPL_NOR_SUPPORT
bool "Support NOR flash"
- depends on SPL
help
Enable support for loading U-Boot from memory-mapped NOR (Negative
OR) flash in SPL. NOR flash is slow to write but fast to read, and
a memory-mapped device makes it very easy to access. Loading from
NOR is typically achieved with just a memcpy().
+config SPL_XIP_SUPPORT
+ bool "Support XIP"
+ depends on SPL
+ help
+ Enable support for execute in place of U-Boot or kernel image. There
+ is no need to copy image from flash to ram if flash supports execute
+ in place. Its very useful in systems having enough flash but not
+ enough ram to load the image.
+
config SPL_ONENAND_SUPPORT
bool "Support OneNAND flash"
- depends on SPL
help
Enable support for OneNAND (Negative AND) flash in SPL. OneNAND is
a type of NAND flash and therefore can be used to allow SPL to
config SPL_OS_BOOT
bool "Activate Falcon Mode"
- depends on SPL && !TI_SECURE_DEVICE
+ depends on !TI_SECURE_DEVICE
default n
help
Enable booting directly to an OS from SPL.
if SPL_OS_BOOT
config SYS_OS_BASE
hex "addr, where OS is found"
- depends on SPL && SPL_NOR_SUPPORT
+ depends on SPL_NOR_SUPPORT
help
Specify the address, where the OS image is found, which
gets booted.
config SPL_PCI_SUPPORT
bool "Support PCI drivers"
- depends on SPL
help
Enable support for PCI in SPL. For platforms that need PCI to boot,
or must perform some init using PCI in SPL, this provides the
config SPL_PCH_SUPPORT
bool "Support PCH drivers"
- depends on SPL
help
Enable support for PCH (Platform Controller Hub) devices in SPL.
These are used to set up GPIOs and the SPI peripheral early in
config SPL_POST_MEM_SUPPORT
bool "Support POST drivers"
- depends on SPL
help
Enable support for POST (Power-on Self Test) in SPL. POST is a
procedure that checks that the hardware (CPU or board) appears to
config SPL_POWER_SUPPORT
bool "Support power drivers"
- depends on SPL
help
Enable support for power control in SPL. This includes support
for PMICs (Power-management Integrated Circuits) and some of the
config SPL_RAM_SUPPORT
bool "Support booting from RAM"
- depends on SPL
default y if MICROBLAZE || ARCH_SOCFPGA || TEGRA || ARCH_ZYNQ
help
Enable booting of an image in RAM. The image can be preloaded or
config SPL_RTC_SUPPORT
bool "Support RTC drivers"
- depends on SPL
help
Enable RTC (Real-time Clock) support in SPL. This includes support
for reading and setting the time. Some RTC devices also have some
config SPL_SATA_SUPPORT
bool "Support loading from SATA"
- depends on SPL
help
Enable support for SATA (Serial AT attachment) in SPL. This allows
use of SATA devices such as hard drives and flash drivers for
config SPL_SERIAL_SUPPORT
bool "Support serial"
- depends on SPL
help
Enable support for serial in SPL. This allows use of a serial UART
for displaying messages while SPL is running. It also brings in
config SPL_SPI_FLASH_SUPPORT
bool "Support SPI flash drivers"
- depends on SPL
help
Enable support for using SPI flash in SPL, and loading U-Boot from
SPI flash. SPI flash (Serial Peripheral Bus flash) is named after
config SPL_SPI_SUPPORT
bool "Support SPI drivers"
- depends on SPL
help
Enable support for using SPI in SPL. This is used for connecting
to SPI flash for loading U-Boot. See SPL_SPI_FLASH_SUPPORT for
enable SPI drivers that are needed for other purposes also, such
as a SPI PMIC.
-config SPL_TIMER_SUPPORT
- bool "Support timer drivers"
- depends on SPL
+config SPL_THERMAL
+ bool "Driver support for thermal devices"
help
- Enable support for timer drivers in SPL. These can be used to get
- a timer value when in SPL, or perhaps for implementing a delay
- function. This enables the drivers in drivers/timer as part of an
- SPL build.
+ Enable support for temperature-sensing devices. Some SoCs have on-chip
+ temperature sensors to permit warnings, speed throttling or even
+ automatic power-off when the temperature gets too high or low. Other
+ devices may be discrete but connected on a suitable bus.
config SPL_USB_HOST_SUPPORT
bool "Support USB host drivers"
- depends on SPL
help
Enable access to USB (Universal Serial Bus) host devices so that
SPL can load U-Boot from a connected USB peripheral, such as a USB
config SPL_USB_GADGET_SUPPORT
bool "Suppport USB Gadget drivers"
- depends on SPL
help
Enable USB Gadget API which allows to enable USB device functions
in SPL.
endchoice
+config SPL_USB_SDP_SUPPORT
+ bool "Support SDP (Serial Download Protocol)"
+ help
+ Enable Serial Download Protocol (SDP) device support in SPL. This
+ allows to download images into memory and execute (jump to) them
+ using the same protocol as implemented by the i.MX family's boot ROM.
endif
config SPL_WATCHDOG_SUPPORT
bool "Support watchdog drivers"
- depends on SPL
help
Enable support for watchdog drivers in SPL. A watchdog is
typically a hardware peripheral which can reset the system when it
config SPL_YMODEM_SUPPORT
bool "Support loading using Ymodem"
- depends on SPL
help
While loading from serial is slow it can be a useful backup when
there is no other option. The Ymodem protocol provides a reliable
means of transmitting U-Boot over a serial line for using in SPL,
with a checksum to ensure correctness.
-config SPL_ATF_SUPPORT
+config SPL_ATF
bool "Support ARM Trusted Firmware"
- depends on SPL && ARM64
+ depends on ARM64
help
- ATF(ARM Trusted Firmware) is a component for ARM arch64 which which
- is loaded by SPL(which is considered as BL2 in ATF terminology).
+ ATF(ARM Trusted Firmware) is a component for ARM AArch64 which
+ is loaded by SPL (which is considered as BL2 in ATF terminology).
More detail at: https://github.com/ARM-software/arm-trusted-firmware
-config SPL_ATF_TEXT_BASE
- depends on SPL_ATF_SUPPORT
- hex "ATF BL31 base address"
+config SPL_ATF_NO_PLATFORM_PARAM
+ bool "Pass no platform parameter"
+ depends on SPL_ATF
+ help
+ While we expect to call a pointer to a valid FDT (or NULL)
+ as the platform parameter to an ATF, some ATF versions are
+ not U-Boot aware and have an insufficiently robust parameter
+ validation to gracefully reject a FDT being passed.
+
+ If this option is enabled, the spl_atf os-type handler will
+ always pass NULL for the platform parameter.
+
+ If your ATF is affected, say Y.
+
+config TPL
+ bool
+ depends on SUPPORT_TPL
+ prompt "Enable TPL"
+ help
+ If you want to build TPL as well as the normal image and SPL, say Y.
+
+if TPL
+
+config TPL_BOARD_INIT
+ bool "Call board-specific initialization in TPL"
+ help
+ If this option is enabled, U-Boot will call the function
+ spl_board_init() from board_init_r(). This function should be
+ provided by the board.
+
+config TPL_LDSCRIPT
+ string "Linker script for the TPL stage"
+ depends on TPL
+ help
+ The TPL stage will usually require a different linker-script
+ (as it runs from a different memory region) than the regular
+ U-Boot stage. Set this to the path of the linker-script to
+ be used for TPL.
+
+ May be left empty to trigger the Makefile infrastructure to
+ fall back to the linker-script used for the SPL stage.
+
+config TPL_NEEDS_SEPARATE_TEXT_BASE
+ bool "TPL needs a separate text-base"
+ default n
+ depends on TPL
+ help
+ Enable, if the TPL stage should not inherit its text-base
+ from the SPL stage. When enabled, a base address for the
+ .text sections of the TPL stage has to be set below.
+
+config TPL_NEEDS_SEPARATE_STACK
+ bool "TPL needs a separate initial stack-pointer"
+ default n
+ depends on TPL
+ help
+ Enable, if the TPL stage should not inherit its initial
+ stack-pointer from the settings for the SPL stage.
+
+config TPL_TEXT_BASE
+ hex "Base address for the .text section of the TPL stage"
+ depends on TPL_NEEDS_SEPARATE_TEXT_BASE
+ help
+ The base address for the .text section of the TPL stage.
+
+config TPL_MAX_SIZE
+ int "Maximum size (in bytes) for the TPL stage"
+ default 0
+ depends on TPL
+ help
+ The maximum size (in bytes) of the TPL stage.
+
+config TPL_STACK
+ hex "Address of the initial stack-pointer for the TPL stage"
+ depends on TPL_NEEDS_SEPARATE_STACK
help
- This is the base address in memory for ATF BL31 text and entry point.
+ The address of the initial stack-pointer for the TPL stage.
+ Usually this will be the (aligned) top-of-stack.
+
+config TPL_BOOTROM_SUPPORT
+ bool "Support returning to the BOOTROM (from TPL)"
+ help
+ Some platforms (e.g. the Rockchip RK3368) provide support in their
+ ROM for loading the next boot-stage after performing basic setup
+ from the TPL stage.
+
+ Enable this option, to return to the BOOTROM through the
+ BOOT_DEVICE_BOOTROM (or fall-through to the next boot device in the
+ boot device list, if not implemented for a given board)
+
+config TPL_DRIVERS_MISC_SUPPORT
+ bool "Support misc drivers in TPL"
+ help
+ Enable miscellaneous drivers in TPL. These drivers perform various
+ tasks that don't fall nicely into other categories, Enable this
+ option to build the drivers in drivers/misc as part of an TPL
+ build, for those that support building in TPL (not all drivers do).
config TPL_ENV_SUPPORT
bool "Support an environment"
- depends on TPL
help
Enable environment support in TPL. See SPL_ENV_SUPPORT for details.
config TPL_I2C_SUPPORT
bool "Support I2C"
- depends on TPL
help
- Enable support for the I2C bus in SPL. See SPL_I2C_SUPPORT for
+ Enable support for the I2C bus in TPL. See SPL_I2C_SUPPORT for
details.
config TPL_LIBCOMMON_SUPPORT
bool "Support common libraries"
- depends on TPL
help
Enable support for common U-Boot libraries within TPL. See
SPL_LIBCOMMON_SUPPORT for details.
config TPL_LIBGENERIC_SUPPORT
bool "Support generic libraries"
- depends on TPL
help
Enable support for generic U-Boot libraries within TPL. See
SPL_LIBGENERIC_SUPPORT for details.
config TPL_MPC8XXX_INIT_DDR_SUPPORT
bool "Support MPC8XXX DDR init"
- depends on TPL
help
Enable support for DDR-SDRAM on the MPC8XXX family within TPL. See
SPL_MPC8XXX_INIT_DDR_SUPPORT for details.
config TPL_MMC_SUPPORT
bool "Support MMC"
- depends on TPL && MMC
+ depends on MMC
help
Enable support for MMC within TPL. See SPL_MMC_SUPPORT for details.
config TPL_NAND_SUPPORT
bool "Support NAND flash"
- depends on TPL
help
- Enable support for NAND in SPL. See SPL_NAND_SUPPORT for details.
+ Enable support for NAND in TPL. See SPL_NAND_SUPPORT for details.
config TPL_SERIAL_SUPPORT
bool "Support serial"
- depends on TPL
help
- Enable support for serial in SPL. See SPL_SERIAL_SUPPORT for
+ Enable support for serial in TPL. See SPL_SERIAL_SUPPORT for
details.
config TPL_SPI_FLASH_SUPPORT
bool "Support SPI flash drivers"
- depends on TPL
help
- Enable support for using SPI flash in SPL. See SPL_SPI_FLASH_SUPPORT
+ Enable support for using SPI flash in TPL. See SPL_SPI_FLASH_SUPPORT
for details.
config TPL_SPI_SUPPORT
bool "Support SPI drivers"
- depends on TPL
help
- Enable support for using SPI in SPL. See SPL_SPI_SUPPORT for
+ Enable support for using SPI in TPL. See SPL_SPI_SUPPORT for
details.
+endif # TPL
+
+endif # SPL
endmenu
projects / oweals / u-boot.git / blobdiff