This is the size of the bootstage record list and is the maximum
number of bootstage records that can be recorded.
+config TPL_BOOTSTAGE_RECORD_COUNT
+ int "Number of boot stage records to store for TPL"
+ default 5
+ help
+ This is the size of the bootstage record list and is the maximum
+ number of bootstage records that can be recorded.
+
config BOOTSTAGE_FDT
bool "Store boot timing information in the OS device tree"
depends on BOOTSTAGE
This should be large enough to hold the bootstage stash. A value of
4096 (4KiB) is normally plenty.
+config SHOW_BOOT_PROGRESS
+ bool "Show boot progress in a board-specific manner"
+ help
+ Defining this option allows to add some board-specific code (calling
+ a user-provided function show_boot_progress(int) that enables you to
+ show the system's boot progress on some display (for example, some
+ LEDs) on your board. At the moment, the following checkpoints are
+ implemented:
+
+ Legacy uImage format:
+
+ Arg Where When
+ 1 common/cmd_bootm.c before attempting to boot an image
+ -1 common/cmd_bootm.c Image header has bad magic number
+ 2 common/cmd_bootm.c Image header has correct magic number
+ -2 common/cmd_bootm.c Image header has bad checksum
+ 3 common/cmd_bootm.c Image header has correct checksum
+ -3 common/cmd_bootm.c Image data has bad checksum
+ 4 common/cmd_bootm.c Image data has correct checksum
+ -4 common/cmd_bootm.c Image is for unsupported architecture
+ 5 common/cmd_bootm.c Architecture check OK
+ -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
+ 6 common/cmd_bootm.c Image Type check OK
+ -6 common/cmd_bootm.c gunzip uncompression error
+ -7 common/cmd_bootm.c Unimplemented compression type
+ 7 common/cmd_bootm.c Uncompression OK
+ 8 common/cmd_bootm.c No uncompress/copy overwrite error
+ -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
+
+ 9 common/image.c Start initial ramdisk verification
+ -10 common/image.c Ramdisk header has bad magic number
+ -11 common/image.c Ramdisk header has bad checksum
+ 10 common/image.c Ramdisk header is OK
+ -12 common/image.c Ramdisk data has bad checksum
+ 11 common/image.c Ramdisk data has correct checksum
+ 12 common/image.c Ramdisk verification complete, start loading
+ -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
+ 13 common/image.c Start multifile image verification
+ 14 common/image.c No initial ramdisk, no multifile, continue.
+
+ 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
+
+ -30 arch/powerpc/lib/board.c Fatal error, hang the system
+ -31 post/post.c POST test failed, detected by post_output_backlog()
+ -32 post/post.c POST test failed, detected by post_run_single()
+
+ 34 common/cmd_doc.c before loading a Image from a DOC device
+ -35 common/cmd_doc.c Bad usage of "doc" command
+ 35 common/cmd_doc.c correct usage of "doc" command
+ -36 common/cmd_doc.c No boot device
+ 36 common/cmd_doc.c correct boot device
+ -37 common/cmd_doc.c Unknown Chip ID on boot device
+ 37 common/cmd_doc.c correct chip ID found, device available
+ -38 common/cmd_doc.c Read Error on boot device
+ 38 common/cmd_doc.c reading Image header from DOC device OK
+ -39 common/cmd_doc.c Image header has bad magic number
+ 39 common/cmd_doc.c Image header has correct magic number
+ -40 common/cmd_doc.c Error reading Image from DOC device
+ 40 common/cmd_doc.c Image header has correct magic number
+ 41 common/cmd_ide.c before loading a Image from a IDE device
+ -42 common/cmd_ide.c Bad usage of "ide" command
+ 42 common/cmd_ide.c correct usage of "ide" command
+ -43 common/cmd_ide.c No boot device
+ 43 common/cmd_ide.c boot device found
+ -44 common/cmd_ide.c Device not available
+ 44 common/cmd_ide.c Device available
+ -45 common/cmd_ide.c wrong partition selected
+ 45 common/cmd_ide.c partition selected
+ -46 common/cmd_ide.c Unknown partition table
+ 46 common/cmd_ide.c valid partition table found
+ -47 common/cmd_ide.c Invalid partition type
+ 47 common/cmd_ide.c correct partition type
+ -48 common/cmd_ide.c Error reading Image Header on boot device
+ 48 common/cmd_ide.c reading Image Header from IDE device OK
+ -49 common/cmd_ide.c Image header has bad magic number
+ 49 common/cmd_ide.c Image header has correct magic number
+ -50 common/cmd_ide.c Image header has bad checksum
+ 50 common/cmd_ide.c Image header has correct checksum
+ -51 common/cmd_ide.c Error reading Image from IDE device
+ 51 common/cmd_ide.c reading Image from IDE device OK
+ 52 common/cmd_nand.c before loading a Image from a NAND device
+ -53 common/cmd_nand.c Bad usage of "nand" command
+ 53 common/cmd_nand.c correct usage of "nand" command
+ -54 common/cmd_nand.c No boot device
+ 54 common/cmd_nand.c boot device found
+ -55 common/cmd_nand.c Unknown Chip ID on boot device
+ 55 common/cmd_nand.c correct chip ID found, device available
+ -56 common/cmd_nand.c Error reading Image Header on boot device
+ 56 common/cmd_nand.c reading Image Header from NAND device OK
+ -57 common/cmd_nand.c Image header has bad magic number
+ 57 common/cmd_nand.c Image header has correct magic number
+ -58 common/cmd_nand.c Error reading Image from NAND device
+ 58 common/cmd_nand.c reading Image from NAND device OK
+
+ -60 common/env_common.c Environment has a bad CRC, using default
+
+ 64 net/eth.c starting with Ethernet configuration.
+ -64 net/eth.c no Ethernet found.
+ 65 net/eth.c Ethernet found.
+
+ -80 common/cmd_net.c usage wrong
+ 80 common/cmd_net.c before calling net_loop()
+ -81 common/cmd_net.c some error in net_loop() occurred
+ 81 common/cmd_net.c net_loop() back without error
+ -82 common/cmd_net.c size == 0 (File with size 0 loaded)
+ 82 common/cmd_net.c trying automatic boot
+ 83 common/cmd_net.c running "source" command
+ -83 common/cmd_net.c some error in automatic boot or "source" command
+ 84 common/cmd_net.c end without errors
+
+ FIT uImage format:
+
+ Arg Where When
+ 100 common/cmd_bootm.c Kernel FIT Image has correct format
+ -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
+ 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
+ -101 common/cmd_bootm.c Can't get configuration for kernel subimage
+ 102 common/cmd_bootm.c Kernel unit name specified
+ -103 common/cmd_bootm.c Can't get kernel subimage node offset
+ 103 common/cmd_bootm.c Found configuration node
+ 104 common/cmd_bootm.c Got kernel subimage node offset
+ -104 common/cmd_bootm.c Kernel subimage hash verification failed
+ 105 common/cmd_bootm.c Kernel subimage hash verification OK
+ -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
+ 106 common/cmd_bootm.c Architecture check OK
+ -106 common/cmd_bootm.c Kernel subimage has wrong type
+ 107 common/cmd_bootm.c Kernel subimage type OK
+ -107 common/cmd_bootm.c Can't get kernel subimage data/size
+ 108 common/cmd_bootm.c Got kernel subimage data/size
+ -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
+ -109 common/cmd_bootm.c Can't get kernel subimage type
+ -110 common/cmd_bootm.c Can't get kernel subimage comp
+ -111 common/cmd_bootm.c Can't get kernel subimage os
+ -112 common/cmd_bootm.c Can't get kernel subimage load address
+ -113 common/cmd_bootm.c Image uncompress/copy overwrite error
+
+ 120 common/image.c Start initial ramdisk verification
+ -120 common/image.c Ramdisk FIT image has incorrect format
+ 121 common/image.c Ramdisk FIT image has correct format
+ 122 common/image.c No ramdisk subimage unit name, using configuration
+ -122 common/image.c Can't get configuration for ramdisk subimage
+ 123 common/image.c Ramdisk unit name specified
+ -124 common/image.c Can't get ramdisk subimage node offset
+ 125 common/image.c Got ramdisk subimage node offset
+ -125 common/image.c Ramdisk subimage hash verification failed
+ 126 common/image.c Ramdisk subimage hash verification OK
+ -126 common/image.c Ramdisk subimage for unsupported architecture
+ 127 common/image.c Architecture check OK
+ -127 common/image.c Can't get ramdisk subimage data/size
+ 128 common/image.c Got ramdisk subimage data/size
+ 129 common/image.c Can't get ramdisk load address
+ -129 common/image.c Got ramdisk load address
+
+ -130 common/cmd_doc.c Incorrect FIT image format
+ 131 common/cmd_doc.c FIT image format OK
+
+ -140 common/cmd_ide.c Incorrect FIT image format
+ 141 common/cmd_ide.c FIT image format OK
+
+ -150 common/cmd_nand.c Incorrect FIT image format
+ 151 common/cmd_nand.c FIT image format OK
+
endmenu
menu "Boot media"
config NAND_BOOT
bool "Support for booting from NAND flash"
default n
- imply NAND
+ imply MTD_RAW_NAND
help
Enabling this will make a U-Boot binary that is capable of being
booted via NAND flash. This is not a must, some SoCs need this,
config ONENAND_BOOT
bool "Support for booting from ONENAND"
default n
- imply NAND
+ imply MTD_RAW_NAND
help
Enabling this will make a U-Boot binary that is capable of being
booted via ONENAND. This is not a must, some SoCs need this,
This is the string of commands that will be used as bootcmd and if
AUTOBOOT is set, automatically run.
+config USE_PREBOOT
+ bool "Enable preboot"
+ help
+ When this option is enabled, the existence of the environment
+ variable "preboot" will be checked immediately before starting the
+ CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
+ entering interactive mode.
+
+ This feature is especially useful when "preboot" is automatically
+ generated or modified. For example, the boot code can modify the
+ "preboot" when a user holds down a certain combination of keys.
+
+config PREBOOT
+ string "preboot default value"
+ depends on USE_PREBOOT
+ default ""
+ help
+ This is the default of "preboot" environment variable.
+
menu "Console"
config MENU
config LOGLEVEL
int "loglevel"
default 4
- range 0 8
+ range 0 10
help
All Messages with a loglevel smaller than the console loglevel will
be compiled in. The loglevels are defined as follows:
- 0 (KERN_EMERG) system is unusable
- 1 (KERN_ALERT) action must be taken immediately
- 2 (KERN_CRIT) critical conditions
- 3 (KERN_ERR) error conditions
- 4 (KERN_WARNING) warning conditions
- 5 (KERN_NOTICE) normal but significant condition
- 6 (KERN_INFO) informational
- 7 (KERN_DEBUG) debug-level messages
+ 0 - emergency
+ 1 - alert
+ 2 - critical
+ 3 - error
+ 4 - warning
+ 5 - note
+ 6 - info
+ 7 - debug
+ 8 - debug content
+ 9 - debug hardware I/O
config SPL_LOGLEVEL
int
depends on PRE_CONSOLE_BUFFER
default 0x2f000000 if ARCH_SUNXI && MACH_SUN9I
default 0x4f000000 if ARCH_SUNXI && !MACH_SUN9I
+ default 0x0f000000 if ROCKCHIP_RK3288
+ default 0x0f200000 if ROCKCHIP_RK3399
help
This sets the start address of the pre-console buffer. This must
be in available memory and is accessed before relocation and
higher than this will be ignored. If possible log statements below
this level will be discarded at build time. Levels:
- 0 - panic
- 1 - critical
- 2 - error
- 3 - warning
- 4 - note
- 5 - info
- 6 - detail
+ 0 - emergency
+ 1 - alert
+ 2 - critical
+ 3 - error
+ 4 - warning
+ 5 - note
+ 6 - info
7 - debug
+ 8 - debug content
+ 9 - debug hardware I/O
config SPL_LOG_MAX_LEVEL
int "Maximum log level to record in SPL"
higher than this will be ignored. If possible log statements below
this level will be discarded at build time. Levels:
- 0 - panic
- 1 - critical
- 2 - error
- 3 - warning
- 4 - note
- 5 - info
- 6 - detail
+ 0 - emergency
+ 1 - alert
+ 2 - critical
+ 3 - error
+ 4 - warning
+ 5 - note
+ 6 - info
7 - debug
+ 8 - debug content
+ 9 - debug hardware I/O
config TPL_LOG_MAX_LEVEL
int "Maximum log level to record in TPL"
higher than this will be ignored. If possible log statements below
this level will be discarded at build time. Levels:
- 0 - panic
- 1 - critical
- 2 - error
- 3 - warning
- 4 - note
- 5 - info
- 6 - detail
+ 0 - emergency
+ 1 - alert
+ 2 - critical
+ 3 - error
+ 4 - warning
+ 5 - note
+ 6 - info
+ 7 - debug
+ 8 - debug content
+ 9 - debug hardware I/O
+
+config LOG_DEFAULT_LEVEL
+ int "Default logging level to display"
+ default 6
+ help
+ This is the default logging level set when U-Boot starts. It can
+ be adjusted later using the 'log level' command. Note that setting
+ this to a value above LOG_MAX_LEVEL will be ineffective, since the
+ higher levels are not compiled in to U-Boot.
+
+ 0 - emergency
+ 1 - alert
+ 2 - critical
+ 3 - error
+ 4 - warning
+ 5 - note
+ 6 - info
7 - debug
+ 8 - debug content
+ 9 - debug hardware I/O
config LOG_CONSOLE
bool "Allow log output to the console"
line number are omitted.
config TPL_LOG_CONSOLE
- bool "Allow log output to the console in SPL"
+ bool "Allow log output to the console in TPL"
depends on TPL_LOG
default y
help
log message is shown - other details like level, category, file and
line number are omitted.
+config LOG_SYSLOG
+ bool "Log output to syslog server"
+ depends on LOG && NET
+ help
+ Enables a log driver which broadcasts log records via UDP port 514
+ to syslog servers.
+
config LOG_TEST
bool "Provide a test for logging"
- depends on LOG
+ depends on LOG && UNIT_TEST
default y if SANDBOX
help
This enables a 'log test' command to test logging. It is normally
the relocation phase. The board function checkboard() is called to do
this.
+config BOUNCE_BUFFER
+ bool "Include bounce buffer API"
+ help
+ Some peripherals support DMA from a subset of physically
+ addressable memory only. To support such peripherals, the
+ bounce buffer API uses a temporary buffer: it copies data
+ to/from DMA regions while managing cache operations.
+
+ A second possible use of bounce buffers is their ability to
+ provide aligned buffers for DMA operations.
+
+config BOARD_TYPES
+ bool "Call get_board_type() to get and display the board type"
+ help
+ If this option is enabled, checkboard() will call get_board_type()
+ to get a string containing the board type and this will be
+ displayed immediately after the model is shown on the console
+ early in boot.
+
menu "Start-up hooks"
config ARCH_EARLY_INIT_R
default 100
depends on UPDATE_TFTP
+config ANDROID_AB
+ bool "Android A/B updates"
+ default n
+ help
+ If enabled, adds support for the new Android A/B update model. This
+ allows the bootloader to select which slot to boot from based on the
+ information provided by userspace via the Android boot_ctrl HAL. This
+ allows a bootloader to try a new version of the system but roll back
+ to previous version if the new one didn't boot all the way.
+
endmenu
menu "Blob list"
endmenu
source "common/spl/Kconfig"
+
+config IMAGE_SIGN_INFO
+ bool
+ select SHA1
+ select SHA256
+ help
+ Enable image_sign_info helper functions.
+
+if IMAGE_SIGN_INFO
+
+config SPL_IMAGE_SIGN_INFO
+ bool
+ select SHA1
+ select SHA256
+ help
+ Enable image_sign_info helper functions in SPL.
+
+endif