cmd: Add Support for UFS commands

[oweals/u-boot.git] / cmd / Kconfig

diff --git a/cmd/Kconfig b/cmd/Kconfig
index 8d2e0a9e4ec426430abaa537783f56af9e38b1c5..82b5d300d2c1c0efc385658fb63d2d34dff6af57 100644 (file)
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
@@ -48,6 +48,8 @@ config SYS_LONGHELP
 
 config SYS_PROMPT
        string "Shell prompt"
+       default "Zynq> " if ARCH_ZYNQ
+       default "ZynqMP> " if ARCH_ZYNQMP
        default "=> "
        help
          This string is displayed in the command line to the left of the
@@ -170,6 +172,15 @@ config AUTOBOOT_MENUKEY
          For example, 33 means "!" in ASCII, so pressing ! at boot would take
          this action.
 
+config AUTOBOOT_MENU_SHOW
+       bool "Show a menu on boot"
+       depends on CMD_BOOTMENU
+       help
+         This enables the boot menu, controlled by environment variables
+         defined by the board. The menu starts after running the 'preboot'
+         environmnent variable (if enabled) and before handling the boot delay.
+         See README.bootmenu for more details.
+
 endmenu
 
 config BUILD_BIN2C
@@ -259,6 +270,54 @@ config CMD_BOOTEFI
        help
          Boot an EFI image from memory.
 
+config BOOTM_LINUX
+       bool "Support booting Linux OS images"
+       depends on CMD_BOOTM || CMD_BOOTZ || CMD_BOOTI
+       default y
+       help
+         Support booting the Linux kernel directly via a command such as bootm
+         or booti or bootz.
+
+config BOOTM_NETBSD
+       bool "Support booting NetBSD (non-EFI) loader images"
+       depends on CMD_BOOTM
+       default y
+       help
+         Support booting NetBSD via the bootm command.
+
+config BOOTM_OPENRTOS
+       bool "Support booting OPENRTOS / FreeRTOS images"
+       depends on CMD_BOOTM
+       help
+         Support booting OPENRTOS / FreeRTOS via the bootm command.
+
+config BOOTM_OSE
+       bool "Support booting Enea OSE images"
+       depends on CMD_BOOTM
+       help
+         Support booting Enea OSE images via the bootm command.
+
+config BOOTM_PLAN9
+       bool "Support booting Plan9 OS images"
+       depends on CMD_BOOTM
+       default y
+       help
+         Support booting Plan9 images via the bootm command.
+
+config BOOTM_RTEMS
+       bool "Support booting RTEMS OS images"
+       depends on CMD_BOOTM
+       default y
+       help
+         Support booting RTEMS images via the bootm command.
+
+config BOOTM_VXWORKS
+       bool "Support booting VxWorks OS images"
+       depends on CMD_BOOTM
+       default y
+       help
+         Support booting VxWorks images via the bootm command.
+
 config CMD_BOOTEFI_HELLO_COMPILE
        bool "Compile a standard EFI hello world binary for testing"
        depends on CMD_BOOTEFI && !CPU_V7M && !SANDBOX
@@ -474,7 +533,6 @@ config CMD_ENV_FLAGS
 config CMD_NVEDIT_EFI
        bool "env [set|print] -e - set/print UEFI variables"
        depends on EFI_LOADER
-       default y
        imply HEXDUMP
        help
          UEFI variables are encoded as some form of U-Boot variables.
@@ -603,6 +661,20 @@ config CMD_MEMORY
            base - print or set address offset
            loop - initialize loop on address range
 
+config MX_CYCLIC
+       bool "Enable cyclic md/mw commands"
+       depends on CMD_MEMORY
+       help
+          Add the "mdc" and "mwc" memory commands. These are cyclic
+          "md/mw" commands.
+          Examples:
+
+         => mdc.b 10 4 500
+         This command will print 4 bytes (10,11,12,13) each 500 ms.
+
+         => mwc.l 100 12345678 10
+         This command will write 12345678 to address 100 all 10 ms.
+
 config CMD_RANDOM
        bool "random"
        default y
@@ -1034,14 +1106,6 @@ config CMD_PCI
          peripherals. Sub-commands allow bus enumeration, displaying and
          changing configuration space and a few other features.
 
-config CMD_PCMCIA
-       bool "pinit - Set up PCMCIA device"
-       help
-         Provides a means to initialise a PCMCIA (Personal Computer Memory
-         Card International Association) device. This is an old standard from
-         about 1990. These devices are typically removable memory or network
-         cards using a standard 68-pin connector.
-
 config CMD_PINMUX
        bool "pinmux - show pins muxing"
        default y if PINCTRL
@@ -1141,6 +1205,13 @@ config CMD_TSI148
          This provides various sub-commands to initialise and configure the
          Turndra tsi148 device. See the command help for full details.
 
+config CMD_UFS
+       bool "Enable UFS - Universal Flash Subsystem commands"
+       depends on UFS
+       help
+         "This provides commands to initialise and configure universal flash
+          subsystem devices"
+
 config CMD_UNIVERSE
        bool "universe - Command to set up the Turndra Universe controller"
        help
@@ -1325,6 +1396,13 @@ config BOOTP_NTPSERVER
        bool "Request & store 'ntpserverip' from BOOTP/DHCP server"
        depends on CMD_BOOTP
 
+config CMD_PCAP
+       bool "pcap capture"
+       help
+         Selecting this will allow capturing all Ethernet packets and store
+         them in physical memory in a PCAP formated file,
+         later to be analyzed by PCAP reader application (IE. WireShark).
+
 config BOOTP_PXE
        bool "Send PXE client arch to BOOTP/DHCP server"
        default y
@@ -1447,7 +1525,7 @@ config CMD_BMP
        bool "Enable 'bmp' command"
        depends on LCD || DM_VIDEO || VIDEO
        help
-         This provides a way to obtain information about a BMP-format iamge
+         This provides a way to obtain information about a BMP-format image
          and to display it. BMP (which presumably stands for BitMaP) is a
          file format defined by Microsoft which supports images of various
          depths, formats and compression methods. Headers on the file