ARM: display5: Remove UART initialization code after DM/DTS conversion (non-console)

[oweals/u-boot.git] / board / liebherr / display5 / common.c

diff --git a/board/liebherr/display5/common.c b/board/liebherr/display5/common.c
index 7b89d169703624ef8ef2591d29543001a1f3ffd2..5e714076a49c969f3a62399d00bcb86268d43fa6 100644 (file)
--- a/board/liebherr/display5/common.c
+++ b/board/liebherr/display5/common.c
@@ -8,14 +8,6 @@
 #include <asm/arch/mx6-pins.h>
 #include "common.h"
 
-iomux_v3_cfg_t const uart_pads[] = {
-       /* UART4 */
-       MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-       MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
 iomux_v3_cfg_t const uart_console_pads[] = {
        /* UART5 */
        MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
@@ -29,11 +21,6 @@ void displ5_set_iomux_uart_spl(void)
        SETUP_IOMUX_PADS(uart_console_pads);
 }
 
-void displ5_set_iomux_uart(void)
-{
-       SETUP_IOMUX_PADS(uart_pads);
-}
-
 iomux_v3_cfg_t const misc_pads_spl[] = {
        /* Emergency recovery pin */
        MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
@@ -45,18 +32,6 @@ void displ5_set_iomux_misc_spl(void)
 }
 
 #ifdef CONFIG_MXC_SPI
-iomux_v3_cfg_t const ecspi_pads[] = {
-       /* SPI3 */
-       MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
-       MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
-       MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
-       MX6_PAD_DISP0_DAT3__ECSPI3_SS0  | MUX_PAD_CTRL(NO_PAD_CTRL),
-       MX6_PAD_DISP0_DAT4__ECSPI3_SS1  | MUX_PAD_CTRL(NO_PAD_CTRL),
-       MX6_PAD_DISP0_DAT5__ECSPI3_SS2  | MUX_PAD_CTRL(NO_PAD_CTRL),
-       MX6_PAD_DISP0_DAT6__ECSPI3_SS3  | MUX_PAD_CTRL(NO_PAD_CTRL),
-       MX6_PAD_DISP0_DAT7__ECSPI3_RDY  | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
 iomux_v3_cfg_t const ecspi2_pads[] = {
        /* SPI2, NOR Flash nWP, CS0 */
        MX6_PAD_CSI0_DAT10__ECSPI2_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
@@ -68,7 +43,7 @@ iomux_v3_cfg_t const ecspi2_pads[] = {
 
 int board_spi_cs_gpio(unsigned int bus, unsigned int cs)
 {
-       if (bus != 1 || cs != (IMX_GPIO_NR(5, 29) << 8))
+       if (bus != 1 || cs != 0)
                return -EINVAL;
 
        return IMX_GPIO_NR(5, 29);
@@ -79,14 +54,8 @@ void displ5_set_iomux_ecspi_spl(void)
        SETUP_IOMUX_PADS(ecspi2_pads);
 }
 
-void displ5_set_iomux_ecspi(void)
-{
-       SETUP_IOMUX_PADS(ecspi_pads);
-}
-
 #else
 void displ5_set_iomux_ecspi_spl(void) {}
-void displ5_set_iomux_ecspi(void) {}
 #endif
 
 #ifdef CONFIG_FSL_ESDHC_IMX
@@ -109,12 +78,6 @@ void displ5_set_iomux_usdhc_spl(void)
        SETUP_IOMUX_PADS(usdhc4_pads);
 }
 
-void displ5_set_iomux_usdhc(void)
-{
-       SETUP_IOMUX_PADS(usdhc4_pads);
-}
-
 #else
 void displ5_set_iomux_usdhc_spl(void) {}
-void displ5_set_iomux_usdhc(void) {}
 #endif