* (C) Copyright 2010
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#define MASK_RBI_DEFECT_16 0x01
/* Multi-Purpose Pins Functionality configuration */
-u32 kwmpp_config[] = {
+static const u32 kwmpp_config[] = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
MPP5_NF_IO7,
MPP6_SYSRST_OUTn,
MPP7_PEX_RST_OUTn,
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
MPP8_GPIO, /* SDA */
MPP9_GPIO, /* SCL */
#endif
}
#endif
-int initialize_unit_leds(void)
+static int initialize_unit_leds(void)
{
/*
* Init the unit LEDs per default they all are
}
#if defined(CONFIG_BOOTCOUNT_LIMIT)
-void set_bootcount_addr(void)
+static void set_bootcount_addr(void)
{
uchar buf[32];
unsigned int bootcountaddr;
int misc_init_r(void)
{
- char *str;
- int mach_type;
-
- str = getenv("mach_type");
- if (str != NULL) {
- mach_type = simple_strtoul(str, NULL, 10);
- printf("Overwriting MACH_TYPE with %d!!!\n", mach_type);
- gd->bd->bi_arch_number = mach_type;
- }
#if defined(CONFIG_KM_MGCOGE3UN)
char *wait_for_ne;
wait_for_ne = getenv("waitforne");
int board_early_init_f(void)
{
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
u32 tmp;
/* set the 2 bitbang i2c pins as output gpios */
tmp = readl(KW_GPIO0_BASE + 4);
writel(tmp & (~KM_KIRKWOOD_SOFT_I2C_GPIOS) , KW_GPIO0_BASE + 4);
#endif
-
+ /* adjust SDRAM size for bank 0 */
+ kw_sdram_size_adjust(0);
kirkwood_mpp_conf(kwmpp_config, NULL);
return 0;
}
int board_init(void)
{
- /*
- * arch number of board
- */
- gd->bd->bi_arch_number = MACH_TYPE_KM_KIRKWOOD;
-
/* address of boot parameters */
gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1);
kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1);
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
/*
* Reinit the GPIO for I2C Bitbang driver so that the now
* available gpio framework is consistent. The calls to
kw_gpio_set_value(KM_FLASH_GPIO_PIN, 1);
}
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- /* Fix this */
- gd->ram_size = get_ram_size((void *)kw_sdram_bar(0),
- kw_sdram_bs(0));
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- int i;
-
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
- gd->bd->bi_dram[i].start = kw_sdram_bar(i);
- gd->bd->bi_dram[i].size = get_ram_size((long *)kw_sdram_bar(i),
- kw_sdram_bs(i));
- }
-}
-
#if (defined(CONFIG_KM_PIGGY4_88E6061))
#define PHY_LED_SEL_REG 0x18
/* reset the phy */
miiphy_reset(name, CONFIG_PHY_BASE_ADR);
}
+#elif defined(CONFIG_KM_PIGGY4_88E6352)
+
+#include <mv88e6352.h>
+
+#if defined(CONFIG_KM_NUSA)
+struct mv88e_sw_reg extsw_conf[] = {
+ /*
+ * port 0, PIGGY4, autoneg
+ * first the fix for the 1000Mbits Autoneg, this is from
+ * a Marvell errata, the regs are undocumented
+ */
+ { PHY(0), PHY_PAGE, AN1000FIX_PAGE },
+ { PHY(0), PHY_STATUS, AN1000FIX },
+ { PHY(0), PHY_PAGE, 0 },
+ /* now the real port and phy configuration */
+ { PORT(0), PORT_PHY, NO_SPEED_FOR },
+ { PORT(0), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ { PHY(0), PHY_1000_CTRL, NO_ADV },
+ { PHY(0), PHY_SPEC_CTRL, AUTO_MDIX_EN },
+ { PHY(0), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST |
+ FULL_DUPLEX },
+ /* port 1, unused */
+ { PORT(1), PORT_CTRL, PORT_DIS },
+ { PHY(1), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(1), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 2, unused */
+ { PORT(2), PORT_CTRL, PORT_DIS },
+ { PHY(2), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 3, unused */
+ { PORT(3), PORT_CTRL, PORT_DIS },
+ { PHY(3), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(3), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 4, ICNEV, SerDes, SGMII */
+ { PORT(4), PORT_STATUS, NO_PHY_DETECT },
+ { PORT(4), PORT_PHY, SPEED_1000_FOR },
+ { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ { PHY(4), PHY_CTRL, PHY_PWR_DOWN },
+ { PHY(4), PHY_SPEC_CTRL, SPEC_PWR_DOWN },
+ /* port 5, CPU_RGMII */
+ { PORT(5), PORT_PHY, RX_RGMII_TIM | TX_RGMII_TIM | FLOW_CTRL_EN |
+ FLOW_CTRL_FOR | LINK_VAL | LINK_FOR | FULL_DPX |
+ FULL_DPX_FOR | SPEED_1000_FOR },
+ { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL },
+ /* port 6, unused, this port has no phy */
+ { PORT(6), PORT_CTRL, PORT_DIS },
+};
+#else
+struct mv88e_sw_reg extsw_conf[] = {};
+#endif
+
+void reset_phy(void)
+{
+#if defined(CONFIG_KM_MVEXTSW_ADDR)
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf,
+ ARRAY_SIZE(extsw_conf));
+ mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR);
+#endif
+}
+
#else
/* Configure and enable MV88E1118 PHY on the piggy*/
void reset_phy(void)
}
#endif
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
void set_sda(int state)
{
I2C_ACTIVE;
projects / oweals / u-boot.git / blobdiff