+// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2010 Freescale Semiconductor, Inc.
* Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
*/
#include <common.h>
#include <hwconfig.h>
#include <i2c.h>
-#include <libfdt.h>
+#include <init.h>
+#include <net.h>
+#include <spi.h>
+#include <linux/delay.h>
+#include <linux/libfdt.h>
#include <fdt_support.h>
#include <pci.h>
#include <mpc83xx.h>
#include <vsc7385.h>
#include <netdev.h>
+#include <fsl_esdhc.h>
#include <asm/io.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_mpc83xx_serdes.h>
-DECLARE_GLOBAL_DATA_PTR;
+/*
+ * The following are used to control the SPI chip selects for the SPI command.
+ */
+#ifdef CONFIG_MPC8XXX_SPI
+
+#define SPI_CS_MASK 0x00400000
-int board_early_init_f(void)
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
- immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
+ return bus == 0 && cs == 0;
+}
- if (in_be32(&im->pmc.pmccr1) & PMCCR1_POWER_OFF)
- gd->flags |= GD_FLG_SILENT;
+void spi_cs_activate(struct spi_slave *slave)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
- return 0;
+ /* active low */
+ clrbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+
+ /* inactive high */
+ setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
}
+#endif /* CONFIG_MPC8XXX_SPI */
+
+#ifdef CONFIG_FSL_ESDHC
+int board_mmc_init(bd_t *bd)
+{
+ return fsl_esdhc_mmc_init(bd);
+}
+#endif
static u8 read_board_info(void)
{
{
immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
sysconf83xx_t *sysconf = &immr->sysconf;
- clk83xx_t *clk = (clk83xx_t *)&immr->clk;
law83xx_t *pcie_law = sysconf->pcielaw;
struct pci_region *pcie_reg[] = { pcie_regions_0 };
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_PEX,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM ,
- SCCR_PCIEXP1CM_1);
-
/* Deassert the resets in the control register */
out_be32(&sysconf->pecr1, 0xE0008000);
udelay(2000);
out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
- mpc83xx_pcie_init(1, pcie_reg, 0);
+ mpc83xx_pcie_init(1, pcie_reg);
}
/*
* Miscellaneous late-boot configurations
*/
int misc_init_r(void)
{
+#ifdef CONFIG_MPC8XXX_SPI
+ immap_t *immr = (immap_t *)CONFIG_SYS_IMMR;
+ sysconf83xx_t *sysconf = &immr->sysconf;
+
+ /*
+ * Set proper bits in SICRH to allow SPI on header J8
+ *
+ * NOTE: this breaks the TSEC2 interface, attached to the Vitesse
+ * switch. The pinmux configuration does not have a fine enough
+ * granularity to support both simultaneously.
+ */
+ clrsetbits_be32(&sysconf->sicrh, SICRH_GPIO_A_TSEC2, SICRH_GPIO_A_GPIO);
+ puts("WARNING: SPI enabled, TSEC2 support is broken\n");
+
+ /* Set header J8 SPI chip select output, disabled */
+ setbits_be32(&immr->gpio[0].dir, SPI_CS_MASK);
+ setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK);
+#endif
+
#ifdef CONFIG_VSC7385_IMAGE
if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
CONFIG_VSC7385_IMAGE_SIZE)) {
return 0;
}
#if defined(CONFIG_OF_BOARD_SETUP)
-void ft_board_setup(void *blob, bd_t *bd)
+int ft_board_setup(void *blob, bd_t *bd)
{
ft_cpu_setup(blob, bd);
- fdt_fixup_dr_usb(blob, bd);
+ fsl_fdt_fixup_dr_usb(blob, bd);
+ fdt_fixup_esdhc(blob, bd);
+
+ return 0;
}
#endif
int rv, num_if = 0;
/* Initialize TSECs first */
- if ((rv = cpu_eth_init(bis)) >= 0)
+ rv = cpu_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize TSECs.\n");
- if ((rv = pci_eth_init(bis)) >= 0)
+ rv = pci_eth_init(bis);
+ if (rv >= 0)
num_if += rv;
else
printf("ERROR: failed to initialize PCI Ethernet.\n");