#include <common.h>
#include <asm/io.h>
#include <asm/arch/atmel_mpddrc.h>
+#include <asm/arch/at91_common.h>
#define SAMA5D3_MPDDRC_VERSION 0x140
u32 ram_address)
{
writel(mode, &mpddr->mr);
+ dmb();
writel(0, ram_address);
}
return 0;
}
+
+int lpddr2_init(const unsigned int base,
+ const unsigned int ram_address,
+ const struct atmel_mpddrc_config *mpddr_value)
+{
+ struct atmel_mpddr *mpddr = (struct atmel_mpddr *)base;
+ u32 reg;
+
+ writel(mpddr_value->lpddr23_lpr, &mpddr->lpddr23_lpr);
+
+ writel(mpddr_value->tim_cal, &mpddr->tim_cal);
+
+ /* 1. Program the memory device type */
+ writel(mpddr_value->md, &mpddr->md);
+
+ /*
+ * 2. Program features of the LPDDR2-SDRAM device and timing parameters
+ */
+ writel(mpddr_value->cr, &mpddr->cr);
+
+ writel(mpddr_value->tpr0, &mpddr->tpr0);
+ writel(mpddr_value->tpr1, &mpddr->tpr1);
+ writel(mpddr_value->tpr2, &mpddr->tpr2);
+
+ /* 3. A NOP command is issued to the LPDDR2-SDRAM */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+ /*
+ * 3bis. Add memory barrier then Perform a write access to
+ * any low-power DDR2-SDRAM address to acknowledge the command.
+ */
+
+ dmb();
+ writel(0, ram_address);
+
+ /* 4. A pause of at least 100 ns must be observed before a single toggle */
+ udelay(1);
+
+ /* 5. A NOP command is issued to the LPDDR2-SDRAM */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+ /* 6. A pause of at least 200 us must be observed before a Reset Command */
+ udelay(200);
+
+ /* 7. A Reset command is issued to the low-power DDR2-SDRAM. */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(63), ram_address);
+
+ /*
+ * 8. A pause of at least tINIT5 must be observed before issuing
+ * any commands
+ */
+ udelay(1);
+
+ /* 9. A Calibration command is issued to the low-power DDR2-SDRAM. */
+ reg = readl(&mpddr->cr);
+ reg &= ~ATMEL_MPDDRC_CR_ZQ_RESET;
+ reg |= ATMEL_MPDDRC_CR_ZQ_RESET;
+ writel(reg, &mpddr->cr);
+
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(10), ram_address);
+
+ /*
+ * 9bis: The ZQ Calibration command is now issued.
+ * Program the type of calibration in the MPDDRC_CR: set the
+ * ZQ field to the SHORT value.
+ */
+ reg = readl(&mpddr->cr);
+ reg &= ~ATMEL_MPDDRC_CR_ZQ_RESET;
+ reg |= ATMEL_MPDDRC_CR_ZQ_SHORT;
+ writel(reg, &mpddr->cr);
+
+ /*
+ * 10: A Mode Register Write command with 1 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(1), ram_address);
+
+ /*
+ * 11: A Mode Register Write command with 2 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(2), ram_address);
+
+ /*
+ * 12: A Mode Register Write command with 3 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(3), ram_address);
+
+ /*
+ * 13: A Mode Register Write command with 16 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(16), ram_address);
+
+ /*
+ * 14: In the DDR Configuration Register, open the input buffers.
+ */
+#ifdef CONFIG_ATMEL_SFR
+ configure_ddrcfg_input_buffers(true);
+#endif
+
+ /* 15. A NOP command is issued to the LPDDR2-SDRAM */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
+
+ /*
+ * 16: A Mode Register Write command with 5 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(5), ram_address);
+
+ /*
+ * 17: A Mode Register Write command with 6 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(6), ram_address);
+
+ /*
+ * 18: A Mode Register Write command with 8 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(8), ram_address);
+
+ /*
+ * 19: A Mode Register Write command with 0 to the MRS field
+ * is issued to the low-power DDR2-SDRAM.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LPDDR2_CMD |
+ ATMEL_MPDDRC_MR_MRS(0), ram_address);
+
+ /*
+ * 20: A Normal Mode command is provided.
+ */
+ atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NORMAL_CMD, ram_address);
+
+ /* 21: In the DDR Configuration Register, close the input buffers. */
+#ifdef CONFIG_ATMEL_SFR
+ configure_ddrcfg_input_buffers(false);
+#endif
+
+ /*
+ * 22: Write the refresh rate into the COUNT field in the MPDDRC
+ * Refresh Timer Register.
+ */
+ writel(mpddr_value->rtr, &mpddr->rtr);
+
+ /* 23. Configre CAL MR4 register */
+ writel(mpddr_value->cal_mr4, &mpddr->cal_mr4);
+
+ return 0;
+}
projects / oweals / u-boot.git / blobdiff