-// SPDX-License-Identifier: GPL-2.0+ OR X11
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
- * (C) Copyright 2017 Theobroma Systems Design und Consulting GmbH
+ * Copyright (c) 2017 Theobroma Systems Design und Consulting GmbH
*/
#include <dt-bindings/pwm/pwm.h>
#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
/ {
- model = "Theobroma Systems RK3399-Q7 SoM";
- compatible = "tsd,rk3399-q7", "tsd,puma", "rockchip,rk3399";
-
- config {
- u-boot,spl-payload-offset = <0x40000>; /* @ 256KB */
- u-boot,mmc-env-offset = <0x4000>; /* @ 16KB */
- u-boot,efi-partition-entries-offset = <0x200000>; /* 2MB */
- u-boot,boot-led = "module_led";
- sysreset-gpio = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- u-boot,spl-boot-order = \
- "same-as-spl", &spiflash, &sdhci, &sdmmc;
- };
-
- aliases {
- spi0 = &spi1;
- spi1 = &spi5;
- };
-
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&leds_pins_puma>;
+ pinctrl-0 = <&led_pin_module>;
- module_led {
+ module-led {
label = "module_led";
gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
+ panic-indicator;
};
+ };
- sd_card_led {
- label = "sd_card_led";
- gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
+ /*
+ * Overwrite the opp-table for CPUB as this board uses a different
+ * regulator (FAN53555) that only allows 10mV steps and therefore
+ * can't reach the operation point target voltages from rk3399-opp.dtsi
+ */
+ /delete-node/ opp-table1;
+ cluster1_opp: opp-table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp00 {
+ opp-hz = /bits/ 64 <408000000>;
+ opp-microvolt = <800000>;
+ clock-latency-ns = <40000>;
+ };
+ opp01 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <800000>;
+ };
+ opp02 {
+ opp-hz = /bits/ 64 <816000000>;
+ opp-microvolt = <830000>;
+ opp-suspend;
+ };
+ opp03 {
+ opp-hz = /bits/ 64 <1008000000>;
+ opp-microvolt = <880000>;
+ };
+ opp04 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <950000>;
+ };
+ opp05 {
+ opp-hz = /bits/ 64 <1416000000>;
+ opp-microvolt = <1030000>;
+ };
+ opp06 {
+ opp-hz = /bits/ 64 <1608000000>;
+ opp-microvolt = <1100000>;
+ };
+ opp07 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <1200000>;
+ };
+ opp08 {
+ opp-hz = /bits/ 64 <1992000000>;
+ opp-microvolt = <1230000>;
+ turbo-mode;
};
};
#clock-cells = <0>;
};
- dw_hdmi_audio: dw-hdmi-audio {
- status = "enabled";
- compatible = "rockchip,dw-hdmi-audio";
- #sound-dai-cells = <0>;
- };
-
- hdmi_codec: hdmi-codec {
- compatible = "simple-audio-card";
- simple-audio-card,format = "i2s";
- simple-audio-card,mclk-fs = <256>;
- simple-audio-card,name = "HDMI-CODEC";
-
- simple-audio-card,cpu {
- sound-dai = <&i2s2>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&hdmi>;
- };
- };
-
- hdmi_sound: hdmi-sound {
- status = "disabled";
- compatible = "simple-audio-card";
- simple-audio-card,format = "i2s";
- simple-audio-card,mclk-fs = <256>;
- simple-audio-card,name = "rockchip,hdmi";
-
- simple-audio-card,cpu {
- sound-dai = <&i2s2>;
- };
- simple-audio-card,codec {
- sound-dai = <&hdmi>;
- };
- };
-
- usbhub_enable: usbhub_enable {
+ vcc1v2_phy: vcc1v2-phy {
compatible = "regulator-fixed";
- regulator-name = "usbhub_enable";
- enable-active-low;
- gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&host_vbus_drv>;
- regulator-boot-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- /*
- * The Qseven BIOS_DISABLE signal on the RK3399-Q7 keeps the on-module
- * eMMC and SPI flash powered-down initially (in fact it keeps the
- * reset signal asserted). Even though it is an enable signal, we
- * model this as a regulator.
- */
- bios_enable: bios_enable {
- compatible = "regulator-fixed";
- u-boot,dm-pre-reloc;
- regulator-name = "bios_enable";
- enable-active-high;
- gpio = <&gpio3 RK_PD5 GPIO_ACTIVE_LOW>;
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
-
- vccadc_ref: vccadc-ref {
- compatible = "regulator-fixed";
- regulator-name = "vcc1v8_sys";
+ regulator-name = "vcc1v2_phy";
regulator-always-on;
regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vcc5v0_sys>;
};
vcc3v3_sys: vcc3v3-sys {
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
};
- vcc5v0_otg: vcc5v0-otg-regulator {
+ vcc5v0_host: vcc5v0-host-regulator {
compatible = "regulator-fixed";
- enable-active-high;
- gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+ gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
+ enable-active-low;
pinctrl-names = "default";
- pinctrl-0 = <&otg_vbus_drv>;
- regulator-name = "vcc5v0_otg";
+ pinctrl-0 = <&vcc5v0_host_en>;
+ regulator-name = "vcc5v0_host";
regulator-always-on;
+ vin-supply = <&vcc5v0_sys>;
};
vcc5v0_sys: vcc5v0-sys {
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
+};
- vcc_phy: vcc-phy-regulator {
- compatible = "regulator-fixed";
- regulator-name = "vcc_phy";
- regulator-always-on;
- regulator-boot-on;
- };
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_b>;
+};
- vdd_log: vdd-log {
- compatible = "pwm-regulator";
- pwms = <&pwm2 0 25000 1>;
- regulator-name = "vdd_log";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-init-microvolt = <950000>;
- };
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_l>;
};
&emmc_phy {
status = "okay";
+ drive-impedance-ohm = <33>;
};
&gmac {
- phy-supply = <&vcc_phy>;
- phy-mode = "rgmii";
- clock_in_out = "input";
- snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
- snps,reset-active-low;
- snps,reset-delays-us = <2 10000 50000>;
assigned-clocks = <&cru SCLK_RMII_SRC>;
assigned-clock-parents = <&clkin_gmac>;
+ clock_in_out = "input";
+ phy-supply = <&vcc1v2_phy>;
+ phy-mode = "rgmii";
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
+ snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
tx_delay = <0x10>;
rx_delay = <0x10>;
status = "okay";
};
-&hdmi {
- #sound-dai-cells = <0>;
+&gpu {
+ mali-supply = <&vdd_gpu>;
status = "okay";
};
i2c-scl-falling-time-ns = <4>;
clock-frequency = <400000>;
- vdd_gpu: vdd_gpu {
- status = "okay";
- compatible = "fcs,fan53555";
- reg = <0x60>;
- vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
- vin-supply = <&vcc5v0_sys>;
- regulator-compatible = "fan53555-reg";
- regulator-name = "vdd_gpu";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1230000>;
- regulator-ramp-delay = <1000>;
- fcs,suspend-voltage-selector = <1>;
- regulator-always-on;
- regulator-boot-on;
- regulator-initial-state = <3>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
rk808: pmic@1b {
compatible = "rockchip,rk808";
reg = <0x1b>;
interrupt-parent = <&gpio1>;
- interrupts = <22 IRQ_TYPE_LEVEL_LOW>; // TODO check interrupt?
+ interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
pinctrl-names = "default";
pinctrl-0 = <&pmic_int_l>;
rockchip,system-power-controller;
wakeup-source;
- #clock-cells = <1>;
- clock-output-names = "xin32k", "rk808-clkout2";
vcc1-supply = <&vcc5v0_sys>;
vcc2-supply = <&vcc5v0_sys>;
regulators {
vdd_center: DCDC_REG1 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vdd_center";
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1350000>;
regulator-ramp-delay = <6001>;
- regulator-name = "vdd_center";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vdd_cpu_l: DCDC_REG2 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vdd_cpu_l";
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1350000>;
regulator-ramp-delay = <6001>;
- regulator-name = "vdd_cpu_l";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
regulator-always-on;
regulator-boot-on;
- regulator-name = "vcc_ddr";
regulator-state-mem {
regulator-on-in-suspend;
};
};
vcc_1v8: DCDC_REG4 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vcc_1v8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
vcc_ldo1: LDO_REG1 {
- regulator-boot-on;
+ regulator-name = "vcc_ldo1";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-name = "vcc_ldo1";
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc1v8_hdmi: LDO_REG2 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vcc1v8_hdmi";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-name = "vcc1v8_hdmi";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc1v8_pmu: LDO_REG3 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vcc1v8_pmu";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-name = "vcc1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
vcc_sd: LDO_REG4 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vcc_sd";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3000000>;
- regulator-name = "vcc_sd";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <3000000>;
};
vcc_ldo5: LDO_REG5 {
- regulator-boot-on;
+ regulator-name = "vcc_ldo5";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
- regulator-name = "vcc_ldo5";
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_ldo6: LDO_REG6 {
- regulator-boot-on;
+ regulator-name = "vcc_ldo6";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
- regulator-name = "vcc_ldo6";
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc0v9_hdmi: LDO_REG7 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vcc0v9_hdmi";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
- regulator-name = "vcc0v9_hdmi";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_efuse: LDO_REG8 {
- regulator-always-on;
- regulator-boot-on;
+ regulator-name = "vcc_efuse";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- regulator-name = "vcc_efuse";
+ regulator-always-on;
+ regulator-boot-on;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc3v3_s3: SWITCH_REG1 {
+ regulator-name = "vcc3v3_s3";
regulator-always-on;
regulator-boot-on;
- regulator-name = "vcc3v3_s3";
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc3v3_s0: SWITCH_REG2 {
+ regulator-name = "vcc3v3_s0";
regulator-always-on;
regulator-boot-on;
- regulator-name = "vcc3v3_s0";
regulator-state-mem {
regulator-off-in-suspend;
};
};
};
};
+
+ vdd_gpu: regulator@60 {
+ compatible = "fcs,fan53555";
+ reg = <0x60>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_gpu";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1230000>;
+ regulator-ramp-delay = <1000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ fan: fan@18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ #cooling-cells = <2>;
+ };
+
+ rtc_twi: rtc@6f {
+ compatible = "isil,isl1208";
+ reg = <0x6f>;
+ };
};
&i2c8 {
status = "okay";
clock-frequency = <400000>;
- vdd_cpu_b: vdd_cpu_b {
- status = "okay";
+ vdd_cpu_b: regulator@60 {
compatible = "fcs,fan53555";
reg = <0x60>;
- vsel-gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
vin-supply = <&vcc5v0_sys>;
- regulator-compatible = "fan53555-reg";
regulator-name = "vdd_cpu_b";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <1230000>;
fcs,suspend-voltage-selector = <1>;
regulator-always-on;
regulator-boot-on;
- regulator-initial-state = <3>;
- regulator-state-mem {
- regulator-off-in-suspend;
- };
};
};
&i2s0 {
+ pinctrl-0 = <&i2s0_2ch_bus>;
+ rockchip,playback-channels = <2>;
+ rockchip,capture-channels = <2>;
status = "okay";
- rockchip,i2s-broken-burst-len;
- rockchip,playback-channels = <8>;
- rockchip,capture-channels = <8>;
- #sound-dai-cells = <0>;
};
-&i2s2 {
- #sound-dai-cells = <0>;
- status = "okay";
+/*
+ * As Q7 does not specify neither a global nor a RX clock for I2S these
+ * signals are not used. Furthermore I2S0_LRCK_RX is used as GPIO.
+ * Therefore we have to redefine the i2s0_2ch_bus definition to prevent
+ * conflicts.
+ */
+&i2s0_2ch_bus {
+ rockchip,pins =
+ <3 RK_PD0 1 &pcfg_pull_none>,
+ <3 RK_PD2 1 &pcfg_pull_none>,
+ <3 RK_PD3 1 &pcfg_pull_none>,
+ <3 RK_PD7 1 &pcfg_pull_none>;
};
&io_domains {
status = "okay";
-
- bt656-supply = <&vcc_1v8>; /* bt656_gpio2ab_ms */
- audio-supply = <&vcc_1v8>; /* audio_gpio3d4a_ms */
- sdmmc-supply = <&vcc_sd>; /* sdmmc_gpio4b_ms */
- gpio1830-supply = <&vcc_1v8>; /* gpio1833_gpio4cd_ms */
-};
-
-&pcie0 {
- assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
- assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
- assigned-clock-rates = <100000000>;
- ep-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
- num-lanes = <4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pcie_clkreqn>;
- status = "okay";
-};
-
-&pcie_phy {
- status = "okay";
+ bt656-supply = <&vcc_1v8>;
+ audio-supply = <&vcc_1v8>;
+ sdmmc-supply = <&vcc_sd>;
+ gpio1830-supply = <&vcc_1v8>;
};
&pmu_io_domains {
pmu1830-supply = <&vcc_1v8>;
};
-&pwm0 {
- status = "okay";
-};
-
&pwm2 {
status = "okay";
};
-&sdhci {
- bus-width = <8>;
- mmc-hs400-1_8v;
- supports-emmc;
- non-removable;
- keep-power-in-suspend;
- mmc-hs400-enhanced-strobe;
- status = "okay";
-};
-
-&sdmmc {
- clock-frequency = <150000000>;
- max-frequency = <40000000>;
- supports-sd;
- bus-width = <4>;
- cap-mmc-highspeed;
- cap-sd-highspeed;
- disable-wp;
- num-slots = <1>;
- vqmmc-supply = <&vcc_sd>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
- status = "okay";
-};
-
-&uart2 {
- status = "okay";
-};
-
-&usb_host0_ehci {
- status = "disabled";
-};
-
-&usb_host0_ohci {
- status = "disabled";
-};
-
-&dwc3_typec0 {
- status = "okay";
-};
-
-&usb_host1_ehci {
- status = "disabled";
-};
-
-&usb_host1_ohci {
- status = "disabled";
-};
-
-&dwc3_typec1 {
- status = "okay";
- tsd,usb-port-power = "usbhub_enable";
-};
-
-&vopb {
- status = "okay";
-};
-
-&gpio1 {
- u-boot,dm-pre-reloc;
-};
-
-&gpio3 {
- u-boot,dm-pre-reloc;
-};
-
&pinctrl {
- /* Pins that are not explicitely used by any devices */
- pinctrl-names = "default";
- pinctrl-0 = <&puma_pin_hog>;
-
- hog {
- puma_pin_hog: puma_pin_hog {
+ i2c8 {
+ i2c8_xfer_a: i2c8-xfer {
rockchip,pins =
- /* We need pull-ups on Q7 buttons */
- <RK_GPIO0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>, /* LID_BTN# */
- <RK_GPIO0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>, /* BATLOW# */
- <RK_GPIO0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>, /* SLP_BTN# */
- <RK_GPIO0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>; /* BIOS_DISABLE# */
+ <1 RK_PC4 1 &pcfg_pull_up>,
+ <1 RK_PC5 1 &pcfg_pull_up>;
};
};
- pmic {
- pmic_int_l: pmic-int-l {
+ leds {
+ led_pin_module: led-module-gpio {
rockchip,pins =
- <RK_GPIO1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+ <2 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
- leds_pins_puma: led_pins@0 {
- rockchip,pins =
- <RK_GPIO2 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>,
- <RK_GPIO1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
- };
-
- usb2 {
- otg_vbus_drv: otg-vbus-drv {
- rockchip,pins =
- <RK_GPIO0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
- };
-
- host_vbus_drv: host-vbus-drv {
+ pmic {
+ pmic_int_l: pmic-int-l {
rockchip,pins =
- <RK_GPIO4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+ <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
- i2c8 {
- i2c8_xfer_a: i2c8-xfer {
+ usb2 {
+ vcc5v0_host_en: vcc5v0-host-en {
rockchip,pins =
- <RK_GPIO1 RK_PC5 RK_FUNC_1 &pcfg_pull_up>,
- <RK_GPIO1 RK_PC4 RK_FUNC_1 &pcfg_pull_up>;
+ <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
};
-&i2c1 {
+&sdhci {
+ bus-width = <8>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ non-removable;
status = "okay";
- clock-frequency = <400000>;
};
-&i2c2 {
- status = "okay";
- clock-frequency = <400000>;
+
+&sdmmc {
+ vqmmc-supply = <&vcc_sd>;
};
-&i2c4 {
+
+&spi1 {
status = "okay";
- clock-frequency = <400000>;
+
+ norflash: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
};
-&i2c6 {
+
+&tcphy1 {
status = "okay";
- clock-frequency = <400000>;
};
-&i2c6_xfer {
- /* Enable pull-ups, the pins would float otherwise. */
- rockchip,pins =
- <RK_GPIO2 RK_PB2 RK_FUNC_2 &pcfg_pull_up>,
- <RK_GPIO2 RK_PB1 RK_FUNC_2 &pcfg_pull_up>;
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
};
-&i2c7 {
+&u2phy1 {
status = "okay";
- clock-frequency = <400000>;
- rtc_twi: rtc@6f {
- compatible = "isil,isl1208";
- reg = <0x6f>;
+ u2phy1_otg: otg-port {
+ status = "okay";
};
- fan: fan@18 {
- compatible = "ti,amc6821";
- reg = <0x18>;
- cooling-min-state = <0>;
- cooling-max-state = <9>;
- #cooling-cells = <2>;
+
+ u2phy1_host: host-port {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
};
};
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_xfer &uart0_cts>;
+&usbdrd3_1 {
status = "okay";
};
-
-&spi1 {
+&usbdrd_dwc3_1 {
status = "okay";
+ dr_mode = "host";
+};
- #address-cells = <1>;
- #size-cells = <0>;
-
- spiflash: w25q32dw@0 {
- u-boot,dm-pre-reloc;
-
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <49500000>;
- spi-cpol;
- spi-cpha;
- };
+&usb_host1_ehci {
+ status = "okay";
};
-&spi5 {
+&usb_host1_ohci {
status = "okay";
};
projects / oweals / u-boot.git / blobdiff