arm: imx: initial support for apalis imx6

[oweals/u-boot.git] / Kconfig

diff --git a/Kconfig b/Kconfig
index 45a06696a19f52083be2c8df5b228f747c2b750b..a44ac9149c5d51033d759cf050b60cbe2f3537de 100644 (file)
--- a/Kconfig
+++ b/Kconfig
@@ -55,11 +55,13 @@ config CC_OPTIMIZE_FOR_SIZE
 
 config DISTRO_DEFAULTS
        bool "Select defaults suitable for booting general purpose Linux distributions"
-       default y if ARCH_SUNXI
+       default y if ARCH_SUNXI || TEGRA
+       default y if ARCH_LS2080A
        default n
        select CMD_BOOTZ if ARM && !ARM64
        select CMD_BOOTI if ARM64
        select CMD_DHCP
+       select CMD_PXE
        select CMD_EXT2
        select CMD_EXT4
        select CMD_FAT
@@ -137,74 +139,6 @@ endmenu            # General setup
 
 menu "Boot images"
 
-config SUPPORT_SPL
-       bool
-
-config SUPPORT_TPL
-       bool
-
-config SPL
-       bool
-       depends on SUPPORT_SPL
-       prompt "Enable SPL"
-       help
-         If you want to build SPL as well as the normal image, say Y.
-
-config SPL_SYS_MALLOC_SIMPLE
-       bool
-       depends on SPL
-       prompt "Only use malloc_simple functions in the SPL"
-       help
-         Say Y here to only use the *_simple malloc functions from
-         malloc_simple.c, rather then using the versions from dlmalloc.c;
-         this will make the SPL binary smaller at the cost of more heap
-         usage as the *_simple malloc functions do not re-use free-ed mem.
-
-config SPL_STACK_R
-       depends on SPL
-       bool "Enable SDRAM location for SPL stack"
-       help
-         SPL starts off execution in SRAM and thus typically has only a small
-         stack available. Since SPL sets up DRAM while in its board_init_f()
-         function, it is possible for the stack to move there before
-         board_init_r() is reached. This option enables a special SDRAM
-         location for the SPL stack. U-Boot SPL switches to this after
-         board_init_f() completes, and before board_init_r() starts.
-
-config SPL_STACK_R_ADDR
-       depends on SPL_STACK_R
-       hex "SDRAM location for SPL stack"
-       help
-         Specify the address in SDRAM for the SPL stack. This will be set up
-         before board_init_r() is called.
-
-config SPL_STACK_R_MALLOC_SIMPLE_LEN
-       depends on SPL_STACK_R && SPL_SYS_MALLOC_SIMPLE
-       hex "Size of malloc_simple heap after switching to DRAM SPL stack"
-       default 0x100000
-       help
-         Specify the amount of the stack to use as memory pool for
-         malloc_simple after switching the stack to DRAM. This may be set
-         to give board_init_r() a larger heap then the initial heap in
-         SRAM which is limited to SYS_MALLOC_F_LEN bytes.
-
-config SPL_SEPARATE_BSS
-       depends on SPL
-       bool "BSS section is in a different memory region from text"
-       help
-         Some platforms need a large BSS region in SPL and can provide this
-         because RAM is already set up. In this case BSS can be moved to RAM.
-         This option should then be enabled so that the correct device tree
-         location is used. Normally we put the device tree at the end of BSS
-         but with this option enabled, it goes at _image_binary_end.
-
-config TPL
-       bool
-       depends on SPL && SUPPORT_TPL
-       prompt "Enable TPL"
-       help
-         If you want to build TPL as well as the normal image and SPL, say Y.
-
 config FIT
        bool "Support Flattened Image Tree"
        help
@@ -365,9 +299,8 @@ config SYS_CLK_FREQ
        help
          TODO: Move CONFIG_SYS_CLK_FREQ for all the architecture
 
-config ARCH_FIXUP_FDT
-       bool "Enable arch_fixup_fdt() call"
-       depends on ARM || MIPS
+config ARCH_FIXUP_FDT_MEMORY
+       bool "Enable arch_fixup_memory_banks() call"
        default y
        help
          Enable FDT memory map syncup before OS boot. This feature can be