mmc: fsl_esdhc_imx: disable the CMD CRC check for standard tuning In current code, we add 1ms dealy after each tuning command for standard tuning method. Adding this 1ms dealy is because USDHC default check the CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning IC logic do not wait for the tuning data sending out by the card, trigger the buffer read ready interrupt immediately, and step to next cycle. So when next time the new tuning command send out by USDHC, card may still not send out the tuning data of the upper command,then some eMMC cards may stuck, can't response to any command, block the whole tuning procedure. If do not check the CMD CRC for tuning, then do not has this issue. USDHC will wait for the tuning data of each tuning command and check them. If the tuning data pass the check, it also means the CMD line also okay for tuning. So this patch disable the CMD CRC check for tuning, save some time for the whole tuning procedure. Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
mmc: fsl_esdhc_imx: fix the mask for tuning start point According the RM, the bit[6~0] of register ESDHC_TUNING_CTRL is TUNING_START_TAP, bit[7] of this register is to disable the command CRC check for standard tuning. So fix it here. Fixes: fa33d207494c ("mmc: split fsl_esdhc driver for i.MX") Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
zfs: fix missing include for disk_partition definition Commit 0528979fa7ab ("part: Drop disk_partition_t typedef") changed to a struct. As a result it uncovered an apparent missing include in zfs_common.h for part.h which actually contains the definition. The ZFS handles the struct exclusively as pointers so it was only a warning. warning: ‘struct disk_partition’ declared inside parameter list will not be visible outside of this definition or declaration void zfs_set_blk_dev(struct blk_desc *rbdd, struct disk_partition *info); Signed-off-by: Joel Johnson <mrjoel@lixil.net> Series-CC: Simon Glass <sjg@chromium.org>
arm: wandboard: move CONFIG_MXC_UART to defconfig For using a debug UART on the Wandboard CONFIG_MXC_UART=y must be set in the .config file. To avoid duplicate definitions move the setting from include/configs/wandboard.h to configs/wandboard_defconfig. Document the debug UART settings in the README. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com>
configs/colibri_vf.h: drop sdboot in favour of distro_bootcmd The distro bootscript uses kernel_image to get the file name of the kernel, so change that variable name. UBI boot has precedence in the default boot command. If one wants to boot from SD with a working NAND installation stop in U-Boot and enter: setenv fdtfile ${soc}-colibri-${fdt_board}.dtb && run distro_bootcmd Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
colibri-imx6ull/imx7: define bootubipart for distro boot When using distro boot to boot from UBI volumes the boot partition has been hardcoded to "UBI" (capital letters). However, our default MTD layout uses "ubi" (lower case letter). Define "ubi" as the default UBI partition for distro boot for Toradex. This allows to use distro boot without having to redefine the MTD partition layout which is useful for TorizonCore. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
mx6cuboxi: Convert to DM_ETH Migration to DM_ETH is mandatory, so convert mx6cuboxi to Ethernet Driver Model. This also brings the benefit of restoring Ethernet functionality. Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Tom Rini <trini@konsulko.com>
ARM: rmobile: Increase PHY auto-negotiation timeout to 20s The ethernet PHY on all known Gen3 boards takes a while to come out of reset, increase the auto-negotiation timeout to prevent it from timing out in case the ethernet is used right after the board was reset. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
colibri_imx6: fix video stdout in default environment After migration to DM 'vga' name is not longer supported, change it to 'vidconsole' in the default environment. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>