From f9f2f12e2cace3685ea0dbb6b6d78789fb75f043 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Thu, 24 May 2012 11:38:39 +0000 Subject: [PATCH] tegra: seaboard: disable SPI, move environment to eMMC The SPI hardware on Seaboard is too broken to use; it is muxed with the console UART and requires evil interactions between the SPI and UART drivers to work even partially. The current code in U-Boot is not sufficient to make this work correctly; auto boot is aborted due to corruption in the UART RX channel interrupting it. Instead, move the environment to eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage, irrespective of whether the board boots from SPI, NAND, or eMMC: if U-Boot is stored in eMMC, it will be stored well below this location. The kernel only uses the general area of the eMMC once booted, not the boot sectors. Boards that are derivatives of Seaboard don't have the muxing issue, and should/could have a separate U-Boot configuration file that does enable SPI if desired. Alternatively, the environment could be stored in NAND flash, but we currently have no driver for that controller. Signed-off-by: Stephen Warren Cc: Simon Glass Signed-off-by: Tom Warren --- include/configs/seaboard.h | 29 ++++------------------------- 1 file changed, 4 insertions(+), 25 deletions(-) diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index cae6e2347e..537ab0e71c 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -51,30 +51,12 @@ /* On Seaboard: GPIO_PI3 = Port I = 8, bit = 3 */ #define CONFIG_UART_DISABLE_GPIO GPIO_PI3 -/* - * On Seaboard, SPIFLASH is muxed with UART4. The next 5 defines are - * needed to work around that design error. - */ -#define CONFIG_SPI_UART_SWITCH -#define CONFIG_SPI_CORRUPTS_UART NV_PA_APB_UARTD_BASE -#define CONFIG_SPI_CORRUPTS_UART_NR 3 -#define CONFIG_SPI_CORRUPTS_UART_DLY 2500 -#undef CONFIG_CMDLINE_EDITING /* avoid NUL in input buffer */ #define CONFIG_MACH_TYPE MACH_TYPE_SEABOARD #define CONFIG_SYS_BOARD_ODMDATA 0x300d8011 /* lp1, 1GB */ #define CONFIG_BOARD_EARLY_INIT_F -/* SPI */ -#define CONFIG_TEGRA_SPI -#define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_WINBOND -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 -#define CONFIG_CMD_SPI -#define CONFIG_CMD_SF -#define CONFIG_SPI_FLASH_SIZE (4 << 20) - /* I2C */ #define CONFIG_TEGRA_I2C #define CONFIG_SYS_I2C_INIT_BOARD @@ -94,13 +76,10 @@ #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT -/* Environment in SPI */ -#define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_MAX_HZ 48000000 -#define CONFIG_ENV_SPI_MODE SPI_MODE_0 - -#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE -#define CONFIG_ENV_OFFSET (CONFIG_SPI_FLASH_SIZE - CONFIG_ENV_SECT_SIZE) +/* Environment in eMMC, at the end of 2nd "boot sector" */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET ((2 * 512 * 1024) - CONFIG_ENV_SIZE) +#define CONFIG_SYS_MMC_ENV_DEV 0 /* USB Host support */ #define CONFIG_USB_EHCI -- 2.25.1