From f85d56bb034d8017bdb6b4bb493eb076a21d11b3 Mon Sep 17 00:00:00 2001 From: Michal Cieslakiewicz Date: Wed, 30 Oct 2019 10:07:27 +0100 Subject: [PATCH] ath79: add support for Netgear WNR2200 This patch adds ath79 support for Netgear WNR2200. Router was previously supported by ar71xx target only (8 MiB variant). Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and 16 MiB for Russia and China markets. Apart from flash size both variants share the same hardware specification. Specification ============= * Description: Netgear WNR2200 * Loader: U-boot * SOC: Atheros AR7241 (360 MHz) * RAM: 64 MiB * Flash: 8 MiB or 16 MiB (SPI NOR) - U-boot binary: 256 KiB - U-boot environment: 64 KiB - Firmware: 7808 KiB or 16000 KiB - ART: 64 KiB * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN * Wireless: 2.4 GHz b/g/n (Atheros AR9287) * USB: yes, 1 x USB 2.0 * Buttons: - Reset - WiFi (rfkill) - WPS * LEDs: - Power (amber/green) - WAN (amber/green) - WLAN (blue) - 4 x LAN (amber/green) - WPS (green) * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1 * Power supply: DC 12V 1.5A * MAC addresses: LAN on case label, WAN +1, WLAN +2 Installation ============ * TFTP recovery * TFTP via U-boot prompt * sysupgrade * Web interface Test build configuration ======================== CONFIG_TARGET_ath79=y CONFIG_TARGET_ath79_generic=y CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y CONFIG_ALL_KMODS=y CONFIG_DEVEL=y CONFIG_CCACHE=y CONFIG_COLLECT_KERNEL_DEBUG=y CONFIG_IMAGEOPT=y CONFIG_KERNEL_DEBUG_INFO=y CONFIG_KERNEL_DEBUG_KERNEL=y Signed-off-by: Michal Cieslakiewicz --- package/boot/uboot-envtools/files/ath79 | 2 + .../ath79/dts/ar7241_netgear_wnr2200-16m.dts | 34 +++ .../ath79/dts/ar7241_netgear_wnr2200-8m.dts | 34 +++ .../ath79/dts/ar7241_netgear_wnr2200.dtsi | 207 ++++++++++++++++++ .../generic/base-files/etc/board.d/01_leds | 12 + .../generic/base-files/etc/board.d/02_network | 6 + .../etc/hotplug.d/firmware/10-ath9k-eeprom | 2 + target/linux/ath79/image/generic.mk | 34 +++ 8 files changed, 331 insertions(+) create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts create mode 100644 target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index d5b94823fd..cc9741cedf 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -22,6 +22,8 @@ glinet,gl-ar300m-nor|\ librerouter,librerouter-v1|\ netgear,ex6400|\ netgear,ex7300|\ +netgear,wnr2200-8m|\ +netgear,wnr2200-16m|\ ocedo,koala|\ ocedo,raccoon|\ openmesh,om5p-ac-v2|\ diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts new file mode 100644 index 0000000000..d182b58c05 --- /dev/null +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200-16m.dts @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar7241_netgear_wnr2200.dtsi" + +/ { + compatible = "netgear,wnr2200-16m", "qca,ar7241"; + model = "Netgear WNR2200 (16M)"; +}; + +&partitions { + partition@0 { + label = "u-boot"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x40000 0x10000>; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0xfa0000>; + compatible = "netgear,uimage"; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x10000>; + read-only; + }; +}; diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts b/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts new file mode 100644 index 0000000000..e926c17893 --- /dev/null +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200-8m.dts @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar7241_netgear_wnr2200.dtsi" + +/ { + compatible = "netgear,wnr2200-8m", "qca,ar7241"; + model = "Netgear WNR2200 (8M)"; +}; + +&partitions { + partition@0 { + label = "u-boot"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x40000 0x10000>; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0x7a0000>; + compatible = "netgear,uimage"; + }; + + art: partition@7f0000 { + label = "art"; + reg = <0x7f0000 0x10000>; + read-only; + }; +}; diff --git a/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi new file mode 100644 index 0000000000..1ce4d11835 --- /dev/null +++ b/target/linux/ath79/dts/ar7241_netgear_wnr2200.dtsi @@ -0,0 +1,207 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar7241.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-boot = &power_amber; + led-failsafe = &power_amber; + led-running = &power_green; + led-upgrade = &power_amber; + label-mac-device = ð1; + }; + + ath9k-keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + wps { + label = "wps"; + linux,code = ; + gpios = <&ath9k 5 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + reset { + label = "reset"; + linux,code = ; + gpios = <&ath9k 6 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + rfkill { + label = "rfkill"; + linux,code = ; + gpios = <&ath9k 3 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins &switch_led_disable_pins &clks_disable_pins>; + + wan_green { + label = "netgear:green:wan"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + + wan_amber { + label = "netgear:amber:wan"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + lan1_green { + label = "netgear:green:lan1"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + lan1_amber { + label = "netgear:amber:lan1"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + + lan2_green { + label = "netgear:green:lan2"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + lan2_amber { + label = "netgear:amber:lan2"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + + lan3_green { + label = "netgear:green:lan3"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + lan3_amber { + label = "netgear:amber:lan3"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + lan4_green { + label = "netgear:green:lan4"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + lan4_amber { + label = "netgear:amber:lan4"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + wps_green { + label = "netgear:green:wps"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + + usb_green { + label = "netgear:green:usb"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + trigger-sources = <&hub_port>; + linux,default-trigger = "usbport"; + }; + }; + + ath9k-leds { + compatible = "gpio-leds"; + + power_green: power_green { + label = "netgear:green:power"; + gpios = <&ath9k 2 GPIO_ACTIVE_LOW>; + }; + + power_amber: power_amber { + label = "netgear:amber:power"; + gpios = <&ath9k 1 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wlan_blue { + label = "netgear:blue:wlan"; + gpios = <&ath9k 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + }; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&art 0x0>; +}; + +ð1 { + status = "okay"; + + compatible = "qca,ar7241-eth", "syscon", "simple-mfd"; + mtd-mac-address = <&art 0x6>; +}; + +&pcie { + status = "okay"; + + ath9k: wifi@0,0 { + compatible = "pci168c,002e"; + reg = <0x0000 0 0 0 0>; + mtd-mac-address = <&art 0x0>; + mtd-mac-address-increment = <1>; + qca,no-eeprom; + #gpio-cells = <2>; + gpio-controller; + + usb_power { + gpio-hog; + line-name = "netgear:power:usb"; + gpios = <4 GPIO_ACTIVE_HIGH>; + output-high; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + hub_port: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index e3575ff041..441091de32 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -103,6 +103,18 @@ glinet,gl-ar300m-lite) glinet,gl-x750) ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1" ;; +netgear,wnr2200-8m|\ +netgear,wnr2200-16m) + ucidef_set_led_netdev "wan-amber" "WAN (amber)" "netgear:amber:wan" "eth0" + ucidef_set_led_switch "lan1green" "LAN1 (green)" "netgear:green:lan1" "switch0" "0x02" "0x04" + ucidef_set_led_switch "lan2green" "LAN2 (green)" "netgear:green:lan2" "switch0" "0x04" "0x04" + ucidef_set_led_switch "lan3green" "LAN3 (green)" "netgear:green:lan3" "switch0" "0x08" "0x04" + ucidef_set_led_switch "lan4green" "LAN4 (green)" "netgear:green:lan4" "switch0" "0x10" "0x04" + ucidef_set_led_switch "lan1amber" "LAN1 (amber)" "netgear:amber:lan1" "switch0" "0x02" "0x02" + ucidef_set_led_switch "lan2amber" "LAN2 (amber)" "netgear:amber:lan2" "switch0" "0x04" "0x02" + ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "netgear:amber:lan3" "switch0" "0x08" "0x02" + ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "netgear:amber:lan4" "switch0" "0x10" "0x02" + ;; pcs,cap324) ucidef_set_led_netdev "lan" "LAN" "pcs:lan:green" "eth0" ;; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 90f622b262..0cf411041d 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -184,6 +184,12 @@ ath79_setup_interfaces() ucidef_add_switch_port_attr "switch0" 2 led 9 ucidef_add_switch_port_attr "switch0" 5 led 2 ;; + netgear,wnr2200-8m|\ + netgear,wnr2200-16m) + ucidef_set_interface_wan "eth0" + ucidef_add_switch "switch0" \ + "0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" + ;; phicomm,k2t) ucidef_add_switch "switch0" \ "0@eth0" "3:lan:1" "5:lan:2" "4:wan" diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 4b07660f02..6a6484879a 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -76,6 +76,8 @@ case "$FIRMWARE" in winchannel,wb2000) caldata_extract "art" 0x5000 0x440 ;; + netgear,wnr2200-8m|\ + netgear,wnr2200-16m|\ pcs,cap324|\ tplink,tl-wr2543-v1|\ tplink,tl-wr842n-v1|\ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index cea903f253..70631c20d0 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -794,6 +794,40 @@ define Device/netgear_wndr3800ch endef TARGET_DEVICES += netgear_wndr3800ch +define Device/netgear_wnr2200_common + ATH_SOC := ar7241 + DEVICE_MODEL := WNR2200 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ledtrig-usbport + NETGEAR_KERNEL_MAGIC := 0x32323030 + NETGEAR_BOARD_ID := wnr2200 + IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | \ + append-rootfs | pad-rootfs + $(Device/netgear_ath79) +endef + +define Device/netgear_wnr2200-8m + $(Device/netgear_wnr2200_common) + DEVICE_VARIANT := 8M + NETGEAR_HW_ID := 29763600+08+64 + IMAGE_SIZE := 7808k + IMAGES += factory-NA.img + IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | \ + check-size $$$$(IMAGE_SIZE) + SUPPORTED_DEVICES += wnr2200 +endef +TARGET_DEVICES += netgear_wnr2200-8m + +define Device/netgear_wnr2200-16m + $(Device/netgear_wnr2200_common) + DEVICE_VARIANT := 16M + DEVICE_ALT0_VENDOR := NETGEAR + DEVICE_ALT0_MODEL := WNR2200 + DEVICE_ALT0_VARIANT := CN/RU + NETGEAR_HW_ID := + IMAGE_SIZE := 16000k +endef +TARGET_DEVICES += netgear_wnr2200-16m + define Device/ocedo_koala ATH_SOC := qca9558 DEVICE_VENDOR := Ocedo -- 2.25.1