From ecfdcee5d9299624c57f0118b137d06d376c115a Mon Sep 17 00:00:00 2001 From: Nikita Kiryanov Date: Tue, 11 Nov 2014 15:46:05 +0200 Subject: [PATCH] powerpc: remove orphaned boards mcc200 and prs200 mcc200 and prs200 are old and have no maintainer. Remove the boards. This also removes the mcc200 specific 1bpp BMP support from common/lcd.c Cc: Wolfgang Denk Cc: Anatolij Gustschin Cc: Masahiro Yamada Cc: York Sun Signed-off-by: Nikita Kiryanov --- arch/powerpc/cpu/mpc5xxx/Kconfig | 4 - board/mcc200/Kconfig | 9 - board/mcc200/MAINTAINERS | 17 - board/mcc200/Makefile | 8 - board/mcc200/auto_update.c | 521 ------------------ board/mcc200/lcd.c | 200 ------- board/mcc200/mcc200.c | 314 ----------- board/mcc200/mt46v16m16-75.h | 16 - board/mcc200/mt48lc16m16a2-75.h | 14 - board/mcc200/mt48lc16m32s2-75.h | 14 - board/mcc200/mt48lc8m32b2-6-7.h | 12 - common/lcd.c | 24 +- configs/mcc200_COM12_SDRAM_defconfig | 4 - configs/mcc200_COM12_defconfig | 4 - configs/mcc200_COM12_highboot_SDRAM_defconfig | 4 - configs/mcc200_COM12_highboot_defconfig | 4 - configs/mcc200_SDRAM_defconfig | 4 - configs/mcc200_defconfig | 3 - configs/mcc200_highboot_SDRAM_defconfig | 4 - configs/mcc200_highboot_defconfig | 4 - configs/prs200_DDR_defconfig | 4 - configs/prs200_defconfig | 4 - configs/prs200_highboot_DDR_defconfig | 4 - configs/prs200_highboot_defconfig | 4 - doc/README.scrapyard | 8 +- include/configs/mcc200.h | 397 ------------- include/lcd.h | 2 +- 27 files changed, 7 insertions(+), 1600 deletions(-) delete mode 100644 board/mcc200/Kconfig delete mode 100644 board/mcc200/MAINTAINERS delete mode 100644 board/mcc200/Makefile delete mode 100644 board/mcc200/auto_update.c delete mode 100644 board/mcc200/lcd.c delete mode 100644 board/mcc200/mcc200.c delete mode 100644 board/mcc200/mt46v16m16-75.h delete mode 100644 board/mcc200/mt48lc16m16a2-75.h delete mode 100644 board/mcc200/mt48lc16m32s2-75.h delete mode 100644 board/mcc200/mt48lc8m32b2-6-7.h delete mode 100644 configs/mcc200_COM12_SDRAM_defconfig delete mode 100644 configs/mcc200_COM12_defconfig delete mode 100644 configs/mcc200_COM12_highboot_SDRAM_defconfig delete mode 100644 configs/mcc200_COM12_highboot_defconfig delete mode 100644 configs/mcc200_SDRAM_defconfig delete mode 100644 configs/mcc200_defconfig delete mode 100644 configs/mcc200_highboot_SDRAM_defconfig delete mode 100644 configs/mcc200_highboot_defconfig delete mode 100644 configs/prs200_DDR_defconfig delete mode 100644 configs/prs200_defconfig delete mode 100644 configs/prs200_highboot_DDR_defconfig delete mode 100644 configs/prs200_highboot_defconfig delete mode 100644 include/configs/mcc200.h diff --git a/arch/powerpc/cpu/mpc5xxx/Kconfig b/arch/powerpc/cpu/mpc5xxx/Kconfig index c1fb92af4b..bd64ea694f 100644 --- a/arch/powerpc/cpu/mpc5xxx/Kconfig +++ b/arch/powerpc/cpu/mpc5xxx/Kconfig @@ -38,9 +38,6 @@ config TARGET_IPEK01 config TARGET_JUPITER bool "Support jupiter" -config TARGET_MCC200 - bool "Support mcc200" - config TARGET_MOTIONPRO bool "Support motionpro" @@ -130,7 +127,6 @@ source "board/jupiter/Kconfig" source "board/manroland/hmi1001/Kconfig" source "board/manroland/mucmc52/Kconfig" source "board/manroland/uc101/Kconfig" -source "board/mcc200/Kconfig" source "board/motionpro/Kconfig" source "board/munices/Kconfig" source "board/phytec/pcm030/Kconfig" diff --git a/board/mcc200/Kconfig b/board/mcc200/Kconfig deleted file mode 100644 index 3b27eeb1de..0000000000 --- a/board/mcc200/Kconfig +++ /dev/null @@ -1,9 +0,0 @@ -if TARGET_MCC200 - -config SYS_BOARD - default "mcc200" - -config SYS_CONFIG_NAME - default "mcc200" - -endif diff --git a/board/mcc200/MAINTAINERS b/board/mcc200/MAINTAINERS deleted file mode 100644 index a59a498795..0000000000 --- a/board/mcc200/MAINTAINERS +++ /dev/null @@ -1,17 +0,0 @@ -MCC200 BOARD -#M: - -S: Maintained -F: board/mcc200/ -F: include/configs/mcc200.h -F: configs/mcc200_defconfig -F: configs/mcc200_COM12_defconfig -F: configs/mcc200_COM12_highboot_defconfig -F: configs/mcc200_COM12_highboot_SDRAM_defconfig -F: configs/mcc200_COM12_SDRAM_defconfig -F: configs/mcc200_highboot_defconfig -F: configs/mcc200_highboot_SDRAM_defconfig -F: configs/mcc200_SDRAM_defconfig -F: configs/prs200_defconfig -F: configs/prs200_DDR_defconfig -F: configs/prs200_highboot_defconfig -F: configs/prs200_highboot_DDR_defconfig diff --git a/board/mcc200/Makefile b/board/mcc200/Makefile deleted file mode 100644 index db3b39646a..0000000000 --- a/board/mcc200/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2003-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := mcc200.o lcd.o auto_update.o diff --git a/board/mcc200/auto_update.c b/board/mcc200/auto_update.c deleted file mode 100644 index 43173ce060..0000000000 --- a/board/mcc200/auto_update.c +++ /dev/null @@ -1,521 +0,0 @@ -/* - * (C) Copyright 2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include -#include -#include -#include -#include -#include -#include - -#ifdef CONFIG_AUTO_UPDATE - -#ifndef CONFIG_USB_OHCI -#error "must define CONFIG_USB_OHCI" -#endif - -#ifndef CONFIG_USB_STORAGE -#error "must define CONFIG_USB_STORAGE" -#endif - -#ifndef CONFIG_SYS_HUSH_PARSER -#error "must define CONFIG_SYS_HUSH_PARSER" -#endif - -#if !defined(CONFIG_CMD_FAT) -#error "must define CONFIG_CMD_FAT" -#endif - -#undef AU_DEBUG - -#undef debug -#ifdef AU_DEBUG -#define debug(fmt,args...) printf (fmt ,##args) -#else -#define debug(fmt,args...) -#endif /* AU_DEBUG */ - -/* possible names of files on the USB stick. */ -#define AU_FIRMWARE "u-boot.img" -#define AU_KERNEL "kernel.img" -#define AU_ROOTFS "rootfs.img" - -struct flash_layout { - long start; - long end; -}; - -/* layout of the FLASH. ST = start address, ND = end address. */ -#define AU_FL_FIRMWARE_ST 0xfC000000 -#define AU_FL_FIRMWARE_ND 0xfC03FFFF -#define AU_FL_KERNEL_ST 0xfC0C0000 -#define AU_FL_KERNEL_ND 0xfC1BFFFF -#define AU_FL_ROOTFS_ST 0xFC1C0000 -#define AU_FL_ROOTFS_ND 0xFCFBFFFF - -static int au_usb_stor_curr_dev; /* current device */ - -/* index of each file in the following arrays */ -#define IDX_FIRMWARE 0 -#define IDX_KERNEL 1 -#define IDX_ROOTFS 2 - -/* max. number of files which could interest us */ -#define AU_MAXFILES 3 - -/* pointers to file names */ -char *aufile[AU_MAXFILES] = { - AU_FIRMWARE, - AU_KERNEL, - AU_ROOTFS -}; - -/* sizes of flash areas for each file */ -long ausize[AU_MAXFILES] = { - (AU_FL_FIRMWARE_ND + 1) - AU_FL_FIRMWARE_ST, - (AU_FL_KERNEL_ND + 1) - AU_FL_KERNEL_ST, - (AU_FL_ROOTFS_ND + 1) - AU_FL_ROOTFS_ST, -}; - -/* array of flash areas start and end addresses */ -struct flash_layout aufl_layout[AU_MAXFILES] = { - { AU_FL_FIRMWARE_ST, AU_FL_FIRMWARE_ND, }, - { AU_FL_KERNEL_ST, AU_FL_KERNEL_ND, }, - { AU_FL_ROOTFS_ST, AU_FL_ROOTFS_ND, }, -}; - -ulong totsize; - -/* where to load files into memory */ -#define LOAD_ADDR ((unsigned char *)0x00200000) - -/* the root file system is the largest image */ -#define MAX_LOADSZ ausize[IDX_ROOTFS] - -/*i2c address of the keypad status*/ -#define I2C_PSOC_KEYPAD_ADDR 0x53 - -/* keypad mask */ -#define KEYPAD_ROW 2 -#define KEYPAD_COL 2 -#define KEYPAD_MASK_LO ((1<<(KEYPAD_COL-1+(KEYPAD_ROW*3-3)))&0xFF) -#define KEYPAD_MASK_HI ((1<<(KEYPAD_COL-1+(KEYPAD_ROW*3-3)))>>8) - -/* externals */ -extern int fat_register_device(block_dev_desc_t *, int); -extern int file_fat_detectfs(void); -extern long file_fat_read(const char *, void *, unsigned long); -extern int i2c_read (unsigned char, unsigned int, int , unsigned char* , int); -extern int flash_sect_erase(ulong, ulong); -extern int flash_sect_protect (int, ulong, ulong); -extern int flash_write (char *, ulong, ulong); -extern int u_boot_hush_start(void); -#ifdef CONFIG_PROGRESSBAR -extern void show_progress(int, int); -extern void lcd_puts (char *); -extern void lcd_enable(void); -#endif - -int au_check_cksum_valid(int idx, long nbytes) -{ - image_header_t *hdr; - - hdr = (image_header_t *)LOAD_ADDR; -#if defined(CONFIG_FIT) - if (genimg_get_format ((void *)hdr) != IMAGE_FORMAT_LEGACY) { - puts ("Non legacy image format not supported\n"); - return -1; - } -#endif - - if (nbytes != image_get_image_size (hdr)) { - printf ("Image %s bad total SIZE\n", aufile[idx]); - return -1; - } - /* check the data CRC */ - if (!image_check_dcrc (hdr)) { - printf ("Image %s bad data checksum\n", aufile[idx]); - return -1; - } - return 0; -} - -int au_check_header_valid(int idx, long nbytes) -{ - image_header_t *hdr; - unsigned long checksum, fsize; - - hdr = (image_header_t *)LOAD_ADDR; -#if defined(CONFIG_FIT) - if (genimg_get_format ((void *)hdr) != IMAGE_FORMAT_LEGACY) { - puts ("Non legacy image format not supported\n"); - return -1; - } -#endif - - /* check the easy ones first */ -#undef CHECK_VALID_DEBUG -#ifdef CHECK_VALID_DEBUG - printf("magic %#x %#x ", image_get_magic (hdr), IH_MAGIC); - printf("arch %#x %#x ", image_get_arch (hdr), IH_ARCH_ARM); - printf("size %#x %#lx ", image_get_data_size (hdr), nbytes); - printf("type %#x %#x ", image_get_type (hdr), IH_TYPE_KERNEL); -#endif - if (nbytes < image_get_header_size ()) { - printf ("Image %s bad header SIZE\n", aufile[idx]); - ausize[idx] = 0; - return -1; - } - if (!image_check_magic (hdr) || !image_check_arch (hdr, IH_ARCH_PPC)) { - printf ("Image %s bad MAGIC or ARCH\n", aufile[idx]); - ausize[idx] = 0; - return -1; - } - /* check the hdr CRC */ - if (!image_check_hcrc (hdr)) { - printf ("Image %s bad header checksum\n", aufile[idx]); - ausize[idx] = 0; - return -1; - } - /* check the type - could do this all in one gigantic if() */ - if ((idx == IDX_FIRMWARE) && !image_check_type (hdr, IH_TYPE_FIRMWARE)) { - printf ("Image %s wrong type\n", aufile[idx]); - ausize[idx] = 0; - return -1; - } - if ((idx == IDX_KERNEL) && !image_check_type (hdr, IH_TYPE_KERNEL)) { - printf ("Image %s wrong type\n", aufile[idx]); - ausize[idx] = 0; - return -1; - } - if ((idx == IDX_ROOTFS) && - (!image_check_type (hdr, IH_TYPE_RAMDISK) && - !image_check_type (hdr, IH_TYPE_FILESYSTEM))) { - printf ("Image %s wrong type\n", aufile[idx]); - ausize[idx] = 0; - return -1; - } - /* recycle checksum */ - checksum = image_get_data_size (hdr); - - fsize = checksum + image_get_header_size (); - /* for kernel and ramdisk the image header must also fit into flash */ - if (idx == IDX_KERNEL || image_check_type (hdr, IH_TYPE_RAMDISK)) - checksum += image_get_header_size (); - - /* check the size does not exceed space in flash. HUSH scripts */ - if ((ausize[idx] != 0) && (ausize[idx] < checksum)) { - printf ("Image %s is bigger than FLASH\n", aufile[idx]); - ausize[idx] = 0; - return -1; - } - /* Update with the real filesize */ - ausize[idx] = fsize; - - return checksum; /* return size to be written to flash */ -} - -int au_do_update(int idx, long sz) -{ - image_header_t *hdr; - char *addr; - long start, end; - int off, rc; - uint nbytes; - - hdr = (image_header_t *)LOAD_ADDR; -#if defined(CONFIG_FIT) - if (genimg_get_format ((void *)hdr) != IMAGE_FORMAT_LEGACY) { - puts ("Non legacy image format not supported\n"); - return -1; - } -#endif - - /* execute a script */ - if (image_check_type (hdr, IH_TYPE_SCRIPT)) { - addr = (char *)((char *)hdr + image_get_header_size ()); - /* stick a NULL at the end of the script, otherwise */ - /* parse_string_outer() runs off the end. */ - addr[image_get_data_size (hdr)] = 0; - addr += 8; - run_command_list(addr, -1, 0); - return 0; - } - - start = aufl_layout[idx].start; - end = aufl_layout[idx].end; - - /* unprotect the address range */ - /* this assumes that ONLY the firmware is protected! */ - if (idx == IDX_FIRMWARE) { -#undef AU_UPDATE_TEST -#ifdef AU_UPDATE_TEST - /* erase it where Linux goes */ - start = aufl_layout[1].start; - end = aufl_layout[1].end; -#endif - flash_sect_protect(0, start, end); - } - - /* - * erase the address range. - */ - debug ("flash_sect_erase(%lx, %lx);\n", start, end); - flash_sect_erase(start, end); - mdelay(100); -#ifdef CONFIG_PROGRESSBAR - show_progress(end - start, totsize); -#endif - - /* strip the header - except for the kernel and ramdisk */ - if (image_check_type (hdr, IH_TYPE_KERNEL) || - image_check_type (hdr, IH_TYPE_RAMDISK)) { - addr = (char *)hdr; - off = image_get_header_size (); - nbytes = image_get_image_size (hdr); - } else { - addr = (char *)((char *)hdr + image_get_header_size ()); -#ifdef AU_UPDATE_TEST - /* copy it to where Linux goes */ - if (idx == IDX_FIRMWARE) - start = aufl_layout[1].start; -#endif - off = 0; - nbytes = image_get_data_size (hdr); - } - - /* copy the data from RAM to FLASH */ - debug ("flash_write(%p, %lx %x)\n", addr, start, nbytes); - rc = flash_write(addr, start, nbytes); - if (rc != 0) { - printf("Flashing failed due to error %d\n", rc); - return -1; - } - -#ifdef CONFIG_PROGRESSBAR - show_progress(nbytes, totsize); -#endif - - /* check the data CRC of the copy */ - if (crc32 (0, (uchar *)(start + off), image_get_data_size (hdr)) != - image_get_dcrc (hdr)) { - printf ("Image %s Bad Data Checksum after COPY\n", aufile[idx]); - return -1; - } - - /* protect the address range */ - /* this assumes that ONLY the firmware is protected! */ - if (idx == IDX_FIRMWARE) - flash_sect_protect(1, start, end); - return 0; -} - -/* - * this is called from board_init() after the hardware has been set up - * and is usable. That seems like a good time to do this. - * Right now the return value is ignored. - */ -int do_auto_update(void) -{ - block_dev_desc_t *stor_dev; - long sz; - int i, res = 0, cnt, old_ctrlc; - char *env; - long start, end; - -#if 0 /* disable key-press detection to speed up boot-up time */ - uchar keypad_status1[2] = {0,0}, keypad_status2[2] = {0,0}; - - /* - * Read keypad status - */ - i2c_read(I2C_PSOC_KEYPAD_ADDR, 0, 0, keypad_status1, 2); - mdelay(500); - i2c_read(I2C_PSOC_KEYPAD_ADDR, 0, 0, keypad_status2, 2); - - /* - * Check keypad - */ - if ( !(keypad_status1[1] & KEYPAD_MASK_LO) || - (keypad_status1[1] != keypad_status2[1])) { - return 0; - } - -#endif - au_usb_stor_curr_dev = -1; - /* start USB */ - if (usb_stop() < 0) { - debug ("usb_stop failed\n"); - return -1; - } - if (usb_init() < 0) { - debug ("usb_init failed\n"); - return -1; - } - /* - * check whether a storage device is attached (assume that it's - * a USB memory stick, since nothing else should be attached). - */ - au_usb_stor_curr_dev = usb_stor_scan(0); - if (au_usb_stor_curr_dev == -1) { - debug ("No device found. Not initialized?\n"); - res = -1; - goto xit; - } - /* check whether it has a partition table */ - stor_dev = get_dev("usb", 0); - if (stor_dev == NULL) { - debug ("uknown device type\n"); - res = -1; - goto xit; - } - if (fat_register_device(stor_dev, 1) != 0) { - debug ("Unable to use USB %d:%d for fatls\n", - au_usb_stor_curr_dev, 1); - res = -1; - goto xit; - } - if (file_fat_detectfs() != 0) { - debug ("file_fat_detectfs failed\n"); - } - - /* - * now check whether start and end are defined using environment - * variables. - */ - start = -1; - end = 0; - env = getenv("firmware_st"); - if (env != NULL) - start = simple_strtoul(env, NULL, 16); - env = getenv("firmware_nd"); - if (env != NULL) - end = simple_strtoul(env, NULL, 16); - if (start >= 0 && end && end > start) { - ausize[IDX_FIRMWARE] = (end + 1) - start; - aufl_layout[IDX_FIRMWARE].start = start; - aufl_layout[IDX_FIRMWARE].end = end; - } - start = -1; - end = 0; - env = getenv("kernel_st"); - if (env != NULL) - start = simple_strtoul(env, NULL, 16); - env = getenv("kernel_nd"); - if (env != NULL) - end = simple_strtoul(env, NULL, 16); - if (start >= 0 && end && end > start) { - ausize[IDX_KERNEL] = (end + 1) - start; - aufl_layout[IDX_KERNEL].start = start; - aufl_layout[IDX_KERNEL].end = end; - } - start = -1; - end = 0; - env = getenv("rootfs_st"); - if (env != NULL) - start = simple_strtoul(env, NULL, 16); - env = getenv("rootfs_nd"); - if (env != NULL) - end = simple_strtoul(env, NULL, 16); - if (start >= 0 && end && end > start) { - ausize[IDX_ROOTFS] = (end + 1) - start; - aufl_layout[IDX_ROOTFS].start = start; - aufl_layout[IDX_ROOTFS].end = end; - } - - /* make certain that HUSH is runnable */ - u_boot_hush_start(); - /* make sure that we see CTRL-C and save the old state */ - old_ctrlc = disable_ctrlc(0); - - /* validate the images first */ - for (i = 0; i < AU_MAXFILES; i++) { - ulong imsize; - /* just read the header */ - sz = file_fat_read(aufile[i], LOAD_ADDR, image_get_header_size ()); - debug ("read %s sz %ld hdr %d\n", - aufile[i], sz, image_get_header_size ()); - if (sz <= 0 || sz < image_get_header_size ()) { - debug ("%s not found\n", aufile[i]); - ausize[i] = 0; - continue; - } - /* au_check_header_valid() updates ausize[] */ - if ((imsize = au_check_header_valid(i, sz)) < 0) { - debug ("%s header not valid\n", aufile[i]); - continue; - } - /* totsize accounts for image size and flash erase size */ - totsize += (imsize + (aufl_layout[i].end - aufl_layout[i].start)); - } - -#ifdef CONFIG_PROGRESSBAR - if (totsize) { - lcd_puts(" Update in progress\n"); - lcd_enable(); - } -#endif - - /* just loop thru all the possible files */ - for (i = 0; i < AU_MAXFILES && totsize; i++) { - if (!ausize[i]) { - continue; - } - sz = file_fat_read(aufile[i], LOAD_ADDR, ausize[i]); - - debug ("read %s sz %ld hdr %d\n", - aufile[i], sz, image_get_header_size ()); - - if (sz != ausize[i]) { - printf ("%s: size %ld read %ld?\n", aufile[i], ausize[i], sz); - continue; - } - - if (sz <= 0 || sz <= image_get_header_size ()) { - debug ("%s not found\n", aufile[i]); - continue; - } - if (au_check_cksum_valid(i, sz) < 0) { - debug ("%s checksum not valid\n", aufile[i]); - continue; - } - /* this is really not a good idea, but it's what the */ - /* customer wants. */ - cnt = 0; - do { - res = au_do_update(i, sz); - /* let the user break out of the loop */ - if (ctrlc() || had_ctrlc()) { - clear_ctrlc(); - break; - } - cnt++; -#ifdef AU_TEST_ONLY - } while (res < 0 && cnt < (AU_MAXFILES + 1)); - if (cnt < (AU_MAXFILES + 1)) -#else - } while (res < 0); -#endif - } - - /* restore the old state */ - disable_ctrlc(old_ctrlc); -#ifdef CONFIG_PROGRESSBAR - if (totsize) { - if (!res) { - lcd_puts("\n Update completed\n"); - } else { - lcd_puts("\n Update error\n"); - } - lcd_enable(); - } -#endif - xit: - usb_stop(); - return res; -} -#endif /* CONFIG_AUTO_UPDATE */ diff --git a/board/mcc200/lcd.c b/board/mcc200/lcd.c deleted file mode 100644 index c911445d97..0000000000 --- a/board/mcc200/lcd.c +++ /dev/null @@ -1,200 +0,0 @@ -/* - * (C) Copyright 2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -#ifdef CONFIG_LCD - -#undef SWAPPED_LCD /* For the previous h/w version */ -/* - * The name of the device used for communication - * with the PSoC. - */ -#define PSOC_PSC MPC5XXX_PSC2 -#define PSOC_BAUD 230400UL - -#define RTS_ASSERT 1 -#define RTS_NEGATE 0 -#define CTS_ASSERT 1 -#define CTS_NEGATE 0 - -/* - * Dimensions in pixels - */ -#define LCD_WIDTH 160 -#define LCD_HEIGHT 100 - -/* - * Dimensions in bytes - */ -#define LCD_BUF_SIZE ((LCD_WIDTH*LCD_HEIGHT)>>3) - -#if LCD_BPP != LCD_MONOCHROME -#error "MCC200 support only monochrome displays (1 bpp)!" -#endif - -#define PSOC_RETRIES 10 /* each of PSOC_WAIT_TIME */ -#define PSOC_WAIT_TIME 10 /* usec */ - -#include -#define FONT_WIDTH VIDEO_FONT_WIDTH - -DECLARE_GLOBAL_DATA_PTR; - -/* - * LCD information - */ -vidinfo_t panel_info = { - LCD_WIDTH, LCD_HEIGHT, LCD_BPP -}; - - -/* - * The device we use to communicate with PSoC - */ -int serial_inited = 0; - -/* - * Imported functions to support the PSoC protocol - */ -extern int serial_init_dev (unsigned long dev_base); -extern void serial_setrts_dev (unsigned long dev_base, int s); -extern int serial_getcts_dev (unsigned long dev_base); -extern void serial_putc_raw_dev(unsigned long dev_base, const char c); - -/* - * Just stubs for our driver, needed for compiling compabilty with - * the common LCD driver code. - */ -void lcd_initcolregs (void) -{ -} - -void lcd_ctrl_init (void *lcdbase) -{ -} - -/* - * Function sends the contents of the frame-buffer to the LCD - */ -void lcd_enable (void) -{ - int i, retries, fb_size; - - if (!serial_inited) { - unsigned long baud; - - baud = gd->baudrate; - gd->baudrate = PSOC_BAUD; - serial_init_dev(PSOC_PSC); - gd->baudrate = baud; - serial_setrts_dev (PSOC_PSC, RTS_ASSERT); - serial_inited = 1; - } - - /* - * Implement PSoC communication protocol: - * 1. Assert RTS, wait CTS assertion - * 2. Transmit data - * 3. Negate RTS, wait CTS negation - */ - - /* 1 */ - serial_setrts_dev (PSOC_PSC, RTS_ASSERT); - for (retries = PSOC_RETRIES; retries; retries--) { - if (serial_getcts_dev(PSOC_PSC) == CTS_ASSERT) - break; - udelay (PSOC_WAIT_TIME); - } - if (!retries) { - printf ("%s Error: PSoC doesn't respond on " - "RTS ASSERT\n", __FUNCTION__); - } - - /* 2 */ - fb_size = panel_info.vl_row * (panel_info.vl_col >> 3); - -#if !defined(SWAPPED_LCD) - for (i=0; ifb_base)[i]); - } -#else - { - int x, y, pwidth; - char *p = (char *)gd->fb_base; - - pwidth = ((panel_info.vl_col+7) >> 3); - for (y=0; y>4 & 0x0F)); - serial_putc_raw_dev (PSOC_PSC, (p[i+x+3]<<4 & 0xF0) | (p[i+x+4]>>4 & 0x0F)); - serial_putc_raw_dev (PSOC_PSC, (p[i+x+4]<<4 & 0xF0) | (p[i+x]>>4 & 0x0F)); - serial_putc_raw_dev (PSOC_PSC, (p[i+x]<<4 & 0xF0) | (p[i+x+1]>>4 & 0x0F)); - serial_putc_raw_dev (PSOC_PSC, (p[i+x+1]<<4 & 0xF0) | (p[i+x+2]>>4 & 0x0F)); - } - } - } -#endif - - /* 3 */ - serial_setrts_dev (PSOC_PSC, RTS_NEGATE); - for (retries = PSOC_RETRIES; retries; retries--) { - if (serial_getcts_dev(PSOC_PSC) == CTS_NEGATE) - break; - udelay (PSOC_WAIT_TIME); - } - - return; -} -#ifdef CONFIG_PROGRESSBAR - -void show_progress (int size, int tot) -{ - int cnt; - int i; - static int rc = 0; - - rc += size; - - cnt = ((LCD_WIDTH/FONT_WIDTH) * rc) / tot; - - rc -= (cnt * tot) / (LCD_WIDTH/FONT_WIDTH); - - for (i = 0; i < cnt; i++) { - lcd_putc(0xdc); - } - - if (cnt) { - lcd_enable(); /* MCC200-specific - send the framebuffer to PSoC */ - } -} - -#endif - -int bmp_display(ulong addr, int x, int y) -{ - int ret; - bmp_image_t *bmp = (bmp_image_t *)addr; - - if (!bmp) { - printf("There is no valid bmp file at the given address\n"); - return 1; - } - - ret = lcd_display_bitmap((ulong)bmp, x, y); - - if ((unsigned long)bmp != addr) - free(bmp); - - return ret; -} - -#endif /* CONFIG_LCD */ diff --git a/board/mcc200/mcc200.c b/board/mcc200/mcc200.c deleted file mode 100644 index 706886b84a..0000000000 --- a/board/mcc200/mcc200.c +++ /dev/null @@ -1,314 +0,0 @@ -/* - * (C) Copyright 2003-2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -/* Two MT48LC8M32B2 for 32 MB */ -/* #include "mt48lc8m32b2-6-7.h" */ - -/* One MT48LC16M32S2 for 64 MB */ -/* #include "mt48lc16m32s2-75.h" */ -#if defined (CONFIG_MCC200_SDRAM) -#include "mt48lc16m16a2-75.h" -#else -#include "mt46v16m16-75.h" -#endif - -DECLARE_GLOBAL_DATA_PTR; - -extern flash_info_t flash_info[]; /* FLASH chips info */ - -extern int do_auto_update(void); -ulong flash_get_size (ulong base, int banknum); - -#ifndef CONFIG_SYS_RAMBOOT -static void sdram_start (int hi_addr) -{ - long hi_addr_bit = hi_addr ? 0x01000000 : 0; - - /* unlock mode register */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* precharge all banks */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit; - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set mode register: extended mode */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_EMODE; - __asm__ volatile ("sync"); - - /* set mode register: reset DLL */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000; - __asm__ volatile ("sync"); -#endif - - /* precharge all banks */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* auto refresh */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 | hi_addr_bit; - __asm__ volatile ("sync"); - - /* set mode register */ - *(vu_long *)MPC5XXX_SDRAM_MODE = SDRAM_MODE; - __asm__ volatile ("sync"); - - /* normal operation */ - *(vu_long *)MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit; - __asm__ volatile ("sync"); - - udelay(10); -} -#endif - -/* - * ATTENTION: Although partially referenced initdram does NOT make real use - * use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE - * is something else than 0x00000000. - */ - -phys_size_t initdram (int board_type) -{ - ulong dramsize = 0; - ulong dramsize2 = 0; - uint svr, pvr; -#ifndef CONFIG_SYS_RAMBOOT - ulong test1, test2; - - /* setup SDRAM chip selects */ - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x0000001e;/* 2G at 0x0 */ - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = 0x80000000;/* disabled */ - __asm__ volatile ("sync"); - - /* setup config registers */ - *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1; - *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2; - __asm__ volatile ("sync"); - -#if SDRAM_DDR - /* set tap delay */ - *(vu_long *)MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY; - __asm__ volatile ("sync"); -#endif - - /* find RAM size using SDRAM CS0 only */ - sdram_start(0); - test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000); - sdram_start(1); - test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000); - if (test1 > test2) { - sdram_start(0); - dramsize = test1; - } else { - dramsize = test2; - } - - /* memory smaller than 1MB is impossible */ - if (dramsize < (1 << 20)) { - dramsize = 0; - } - - /* set SDRAM CS0 size according to the amount of RAM found */ - if (dramsize > 0) { - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0x13 + __builtin_ffs(dramsize >> 20) - 1; - } else { - *(vu_long *)MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */ - } - - /* let SDRAM CS1 start right after CS0 */ - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */ - - /* find RAM size using SDRAM CS1 only */ - if (!dramsize) - sdram_start(0); - test2 = test1 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000); - if (!dramsize) { - sdram_start(1); - test2 = get_ram_size((long *)(CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000); - } - if (test1 > test2) { - sdram_start(0); - dramsize2 = test1; - } else { - dramsize2 = test2; - } - - /* memory smaller than 1MB is impossible */ - if (dramsize2 < (1 << 20)) { - dramsize2 = 0; - } - - /* set SDRAM CS1 size according to the amount of RAM found */ - if (dramsize2 > 0) { - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize - | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1); - } else { - *(vu_long *)MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */ - } - -#else /* CONFIG_SYS_RAMBOOT */ - - /* retrieve size of memory connected to SDRAM CS0 */ - dramsize = *(vu_long *)MPC5XXX_SDRAM_CS0CFG & 0xFF; - if (dramsize >= 0x13) { - dramsize = (1 << (dramsize - 0x13)) << 20; - } else { - dramsize = 0; - } - - /* retrieve size of memory connected to SDRAM CS1 */ - dramsize2 = *(vu_long *)MPC5XXX_SDRAM_CS1CFG & 0xFF; - if (dramsize2 >= 0x13) { - dramsize2 = (1 << (dramsize2 - 0x13)) << 20; - } else { - dramsize2 = 0; - } - -#endif /* CONFIG_SYS_RAMBOOT */ - - /* - * On MPC5200B we need to set the special configuration delay in the - * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM - * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190: - * - * "The SDelay should be written to a value of 0x00000004. It is - * required to account for changes caused by normal wafer processing - * parameters." - */ - svr = get_svr(); - pvr = get_pvr(); - if ((SVR_MJREV(svr) >= 2) && (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) { - *(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04; - __asm__ volatile ("sync"); - } - - return dramsize + dramsize2; -} - -int checkboard (void) -{ -#if defined(CONFIG_PRS200) - puts ("Board: PRS200\n"); -#else - puts ("Board: MCC200\n"); -#endif - return 0; -} - -int misc_init_r (void) -{ - ulong flash_sup_end, snum; - - /* - * Adjust flash start and offset to detected values - */ - gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; - gd->bd->bi_flashoffset = 0; - - /* - * Check if boot FLASH isn't max size - */ - if (gd->bd->bi_flashsize < (0 - CONFIG_SYS_FLASH_BASE)) { - /* adjust mapping */ - *(vu_long *)MPC5XXX_BOOTCS_START = *(vu_long *)MPC5XXX_CS0_START = - START_REG(gd->bd->bi_flashstart); - *(vu_long *)MPC5XXX_BOOTCS_STOP = *(vu_long *)MPC5XXX_CS0_STOP = - STOP_REG(gd->bd->bi_flashstart, gd->bd->bi_flashsize); - - /* - * Re-check to get correct base address - */ - flash_get_size(gd->bd->bi_flashstart, CONFIG_SYS_MAX_FLASH_BANKS - 1); - - /* - * Re-do flash protection upon new addresses - */ - flash_protect (FLAG_PROTECT_CLEAR, - gd->bd->bi_flashstart, 0xffffffff, - &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]); - - /* Monitor protection ON by default */ - flash_protect (FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, - &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]); - - /* Environment protection ON by default */ - flash_protect (FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1, - &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]); - - /* Redundant environment protection ON by default */ - flash_protect (FLAG_PROTECT_SET, - CONFIG_ENV_ADDR_REDUND, - CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1, - &flash_info[CONFIG_SYS_MAX_FLASH_BANKS - 1]); - } - - if (gd->bd->bi_flashsize > (32 << 20)) { - /* Unprotect the upper bank of the Flash */ - *(volatile int*)MPC5XXX_CS0_CFG |= (1 << 6); - flash_protect (FLAG_PROTECT_CLEAR, - flash_info[0].start[0] + flash_info[0].size / 2, - (flash_info[0].start[0] - 1) + flash_info[0].size, - &flash_info[0]); - *(volatile int*)MPC5XXX_CS0_CFG &= ~(1 << 6); - printf ("Warning: Only 32 of 64 MB of Flash are accessible from U-Boot\n"); - flash_info[0].size = 32 << 20; - for (snum = 0, flash_sup_end = gd->bd->bi_flashstart + (32<<20); - flash_info[0].start[snum] < flash_sup_end; - snum++); - flash_info[0].sector_count = snum; - } - -#ifdef CONFIG_AUTO_UPDATE - do_auto_update(); -#endif - return (0); -} - -#ifdef CONFIG_PCI -static struct pci_controller hose; - -extern void pci_mpc5xxx_init(struct pci_controller *); - -void pci_init_board(void) -{ - pci_mpc5xxx_init(&hose); -} -#endif - -#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) - -void init_ide_reset (void) -{ - debug ("init_ide_reset\n"); - -} - -void ide_set_reset (int idereset) -{ - debug ("ide_reset(%d)\n", idereset); - -} -#endif - -#if defined(CONFIG_CMD_DOC) -void doc_init (void) -{ - doc_probe (CONFIG_SYS_DOC_BASE); -} -#endif diff --git a/board/mcc200/mt46v16m16-75.h b/board/mcc200/mt46v16m16-75.h deleted file mode 100644 index 9068fbf36f..0000000000 --- a/board/mcc200/mt46v16m16-75.h +++ /dev/null @@ -1,16 +0,0 @@ -/* - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#define SDRAM_DDR 1 /* is DDR */ - -/* Settings for XLB = 132 MHz */ -#define SDRAM_MODE 0x018D0000 -#define SDRAM_EMODE 0x40090000 -#define SDRAM_CONTROL 0x714f0f00 -#define SDRAM_CONFIG1 0x73722930 -#define SDRAM_CONFIG2 0x47770000 -#define SDRAM_TAPDELAY 0x10000000 diff --git a/board/mcc200/mt48lc16m16a2-75.h b/board/mcc200/mt48lc16m16a2-75.h deleted file mode 100644 index 0133eaa2ca..0000000000 --- a/board/mcc200/mt48lc16m16a2-75.h +++ /dev/null @@ -1,14 +0,0 @@ -/* - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#define SDRAM_DDR 0 /* is SDR */ - -/* Settings for XLB = 132 MHz */ -#define SDRAM_MODE 0x00CD0000 -#define SDRAM_CONTROL 0x504F0000 -#define SDRAM_CONFIG1 0xD2322800 -#define SDRAM_CONFIG2 0x8AD70000 diff --git a/board/mcc200/mt48lc16m32s2-75.h b/board/mcc200/mt48lc16m32s2-75.h deleted file mode 100644 index 0133eaa2ca..0000000000 --- a/board/mcc200/mt48lc16m32s2-75.h +++ /dev/null @@ -1,14 +0,0 @@ -/* - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#define SDRAM_DDR 0 /* is SDR */ - -/* Settings for XLB = 132 MHz */ -#define SDRAM_MODE 0x00CD0000 -#define SDRAM_CONTROL 0x504F0000 -#define SDRAM_CONFIG1 0xD2322800 -#define SDRAM_CONFIG2 0x8AD70000 diff --git a/board/mcc200/mt48lc8m32b2-6-7.h b/board/mcc200/mt48lc8m32b2-6-7.h deleted file mode 100644 index 13aebbd8af..0000000000 --- a/board/mcc200/mt48lc8m32b2-6-7.h +++ /dev/null @@ -1,12 +0,0 @@ -/* - * Configuration Registers for the MT48LC8M32B2 SDRAM on the MPC5200 platform - */ - -#define SDRAM_DDR 0 /* is SDR */ - -/* Settings for XLB = 132 MHz */ - -#define SDRAM_MODE 0x008d0000 /* CL-3 BURST-8 -> Mode Register MBAR + 0x0100 */ -#define SDRAM_CONTROL 0x504f0000 /* Control Register MBAR + 0x0104 */ -#define SDRAM_CONFIG1 0xc2222900 /* Delays between commands -> Configuration Register 1 MBAR + 0x0108 */ -#define SDRAM_CONFIG2 0x88c70000 /* Delays between commands -> Configuration Register 2 MBAR + 0x010C */ diff --git a/common/lcd.c b/common/lcd.c index 787d80e3cb..37147af805 100644 --- a/common/lcd.c +++ b/common/lcd.c @@ -881,7 +881,7 @@ static void lcd_display_rle8_bitmap(bmp_image_t *bmp, ushort *cmap, uchar *fb, } #endif -#if defined(CONFIG_MPC823) || defined(CONFIG_MCC200) +#if defined(CONFIG_MPC823) #define FB_PUT_BYTE(fb, from) *(fb)++ = (255 - *(from)++) #else #define FB_PUT_BYTE(fb, from) *(fb)++ = *(from)++ @@ -906,9 +906,7 @@ static inline void fb_put_word(uchar **fb, uchar **from) int lcd_display_bitmap(ulong bmp_image, int x, int y) { -#if !defined(CONFIG_MCC200) ushort *cmap = NULL; -#endif ushort *cmap_base = NULL; ushort i, j; uchar *fb; @@ -956,8 +954,6 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y) debug("Display-bmp: %d x %d with %d colors\n", (int)width, (int)height, (int)colors); -#if !defined(CONFIG_MCC200) - /* MCC200 LCD doesn't need CMAP, supports 1bpp b&w only */ if (bmp_bpix == 8) { cmap = configuration_get_cmap(); cmap_base = cmap; @@ -985,24 +981,6 @@ int lcd_display_bitmap(ulong bmp_image, int x, int y) #endif } } -#endif - /* - * BMP format for Monochrome assumes that the state of a - * pixel is described on a per Bit basis, not per Byte. - * So, in case of Monochrome BMP we should align widths - * on a byte boundary and convert them from Bit to Byte - * units. - * Probably, PXA250 and MPC823 process 1bpp BMP images in - * their own ways, so make the converting to be MCC200 - * specific. - */ -#if defined(CONFIG_MCC200) - if (bpix == 1) { - width = ((width + 7) & ~7) >> 3; - x = ((x + 7) & ~7) >> 3; - pwidth= ((pwidth + 7) & ~7) >> 3; - } -#endif padded_width = (width & 0x3 ? (width & ~0x3) + 4 : width); diff --git a/configs/mcc200_COM12_SDRAM_defconfig b/configs/mcc200_COM12_SDRAM_defconfig deleted file mode 100644 index be6dbd7240..0000000000 --- a/configs/mcc200_COM12_SDRAM_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12,MCC200_SDRAM" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/mcc200_COM12_defconfig b/configs/mcc200_COM12_defconfig deleted file mode 100644 index 6ed86358a1..0000000000 --- a/configs/mcc200_COM12_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/mcc200_COM12_highboot_SDRAM_defconfig b/configs/mcc200_COM12_highboot_SDRAM_defconfig deleted file mode 100644 index 5f93702f0e..0000000000 --- a/configs/mcc200_COM12_highboot_SDRAM_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12,SYS_TEXT_BASE=0xFFF00000,MCC200_SDRAM" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/mcc200_COM12_highboot_defconfig b/configs/mcc200_COM12_highboot_defconfig deleted file mode 100644 index 7abb0a40be..0000000000 --- a/configs/mcc200_COM12_highboot_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="CONSOLE_COM12,SYS_TEXT_BASE=0xFFF00000" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/mcc200_SDRAM_defconfig b/configs/mcc200_SDRAM_defconfig deleted file mode 100644 index 37761b5625..0000000000 --- a/configs/mcc200_SDRAM_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="MCC200_SDRAM" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/mcc200_defconfig b/configs/mcc200_defconfig deleted file mode 100644 index b6aafec3ee..0000000000 --- a/configs/mcc200_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/mcc200_highboot_SDRAM_defconfig b/configs/mcc200_highboot_SDRAM_defconfig deleted file mode 100644 index 94d33e5896..0000000000 --- a/configs/mcc200_highboot_SDRAM_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFFF00000,MCC200_SDRAM" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/mcc200_highboot_defconfig b/configs/mcc200_highboot_defconfig deleted file mode 100644 index f863dd9fcb..0000000000 --- a/configs/mcc200_highboot_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFFF00000" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/prs200_DDR_defconfig b/configs/prs200_DDR_defconfig deleted file mode 100644 index 541fb995af..0000000000 --- a/configs/prs200_DDR_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PRS200" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/prs200_defconfig b/configs/prs200_defconfig deleted file mode 100644 index a094a088cb..0000000000 --- a/configs/prs200_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PRS200,MCC200_SDRAM" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/prs200_highboot_DDR_defconfig b/configs/prs200_highboot_DDR_defconfig deleted file mode 100644 index b8eb8d4d81..0000000000 --- a/configs/prs200_highboot_DDR_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PRS200,SYS_TEXT_BASE=0xFFF00000" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/configs/prs200_highboot_defconfig b/configs/prs200_highboot_defconfig deleted file mode 100644 index 8d68cc06b8..0000000000 --- a/configs/prs200_highboot_defconfig +++ /dev/null @@ -1,4 +0,0 @@ -CONFIG_SYS_EXTRA_OPTIONS="PRS200,SYS_TEXT_BASE=0xFFF00000,MCC200_SDRAM" -CONFIG_PPC=y -CONFIG_MPC5xxx=y -CONFIG_TARGET_MCC200=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index bd4dd3c829..8ba6e0ae65 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,9 +12,11 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= -TOP5200 powerpc mpc5200 - - Reinhard Meyer -TOP860 powerpc mpc860 - - Reinhard Meyer -TOP9000 arm at91sam9xeXXX - - Reinhard Meyer +PRS200 powerpc mpc5200 - - +MCC200 powerpc mpc5200 - - +TOP5200 powerpc mpc5200 d58a945 2014-10-28 Reinhard Meyer +TOP860 powerpc mpc860 d58a945 2014-10-28 Reinhard Meyer +TOP9000 arm at91sam9xeXXX d58a945 2014-10-28 Reinhard Meyer TQM8272 powerpc mpc8260 f06f9a1 2014-10-27 Wolfgang Denk TQM8260 powerpc mpc8260 ccc1950 2014-10-27 Wolfgang Denk IDS8247 powerpc mpc8260 6afb357 2014-10-27 Heiko Schocher diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h deleted file mode 100644 index a317782dbe..0000000000 --- a/include/configs/mcc200.h +++ /dev/null @@ -1,397 +0,0 @@ -/* - * (C) Copyright 2006-2008 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 -#define CONFIG_MCC200 1 /* MCC200 board */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFC000000 boot low (standard configuration) - * 0xFFF00000 boot high - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFC000000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ - -#define CONFIG_MISC_INIT_R - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - * - * To select console on the one of 8 external UARTs, - * define CONFIG_QUART_CONSOLE as 1, 2, 3, or 4 for the first Quad UART, - * or as 5, 6, 7, or 8 for the second Quad UART. - * COM11, COM12, COM13, COM14 are located on the second Quad UART. - * - * CONFIG_PSC_CONSOLE must be undefined in this case. - */ -#if !defined(CONFIG_PRS200) -/* MCC200 configuration: */ -#ifdef CONFIG_CONSOLE_COM12 -#define CONFIG_QUART_CONSOLE 6 /* console is on UARTF of QUART2 */ -#else -#define CONFIG_QUART_CONSOLE 8 /* console is on UARTH of QUART2 */ -#endif -#else -/* PRS200 configuration: */ -#undef CONFIG_QUART_CONSOLE -#endif /* CONFIG_PRS200 */ -/* - * To select console on PSC1, define CONFIG_PSC_CONSOLE as 1 - * and undefine CONFIG_QUART_CONSOLE. - */ -#if !defined(CONFIG_PRS200) -/* MCC200 configuration: */ -#define CONFIG_PSC_CONSOLE 1 /* PSC1 may be COM */ -#define CONFIG_PSC_CONSOLE2 2 /* PSC2 is PSoC */ -#else -/* PRS200 configuration: */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#endif -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#define CONFIG_MII 1 - -#define CONFIG_DOS_PARTITION - -/* USB */ -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -/* automatic software updates (see board/mcc200/auto_update.c) */ -#define CONFIG_AUTO_UPDATE 1 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_USB - -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#ifdef CONFIG_PRS200 -# define CONFIG_SYS__BOARDNAME "prs200" -# define CONFIG_SYS__LINUX_CONSOLE "ttyS0" -#else -# define CONFIG_SYS__BOARDNAME "mcc200" -# define CONFIG_SYS__LINUX_CONSOLE "ttyEU5" -#endif - -/* Network */ -#define CONFIG_ETHADDR 00:17:17:ff:00:00 -#define CONFIG_IPADDR 10.76.9.29 -#define CONFIG_SERVERIP 10.76.9.1 - -#include /* For U-Boot version */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "ubootver=" U_BOOT_VERSION "\0" \ - "netdev=eth0\0" \ - "hostname=" CONFIG_SYS__BOARDNAME "\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/mtdblock2 " \ - "rootfstype=cramfs\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addcons=setenv bootargs ${bootargs} " \ - "console=${console},${baudrate} " \ - "ubootver=${ubootver} board=${board}\0" \ - "flash_nfs=run nfsargs addip addcons;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addcons;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};" \ - "run nfsargs addip addcons;bootm\0" \ - "console=" CONFIG_SYS__LINUX_CONSOLE "\0" \ - "rootpath=/opt/eldk/ppc_6xx\0" \ - "bootfile=/tftpboot/" CONFIG_SYS__BOARDNAME "/uImage\0" \ - "load=tftp 200000 /tftpboot/" CONFIG_SYS__BOARDNAME "/u-boot.bin\0" \ - "text_base=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ - "kernel_addr=0xFC0C0000\0" \ - "update=protect off ${text_base} +${filesize};" \ - "era ${text_base} +${filesize};" \ - "cp.b 200000 ${text_base} ${filesize}\0" \ - "unlock=yes\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * Flash configuration (8,16 or 32 MB) - * TEXT base always at 0xFFF00000 - * ENV_ADDR always at 0xFFF40000 - * FLASH_BASE at 0xFC000000 for 64 MB (only 32MB are supported, not enough addr lines!!!) - * 0xFE000000 for 32 MB - * 0xFF000000 for 16 MB - * 0xFF800000 for 8 MB - */ -#define CONFIG_SYS_FLASH_BASE 0xfc000000 -#define CONFIG_SYS_FLASH_SIZE 0x04000000 - -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ - -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ - -#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */ - -#if CONFIG_SYS_TEXT_BASE == CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xf0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -/* #define CONFIG_MPC5xxx_FEC 1 */ -/* #define CONFIG_MPC5xxx_FEC_MII100 */ -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 1 - -/* - * LCD Splash Screen - */ -#if !defined(CONFIG_PRS200) -#define CONFIG_LCD 1 -#define CONFIG_PROGRESSBAR 1 -#endif - -#if defined(CONFIG_LCD) -#define CONFIG_SPLASH_SCREEN 1 -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -#define LCD_BPP LCD_MONOCHROME -#endif - -/* - * GPIO configuration - */ -/* 0x10000004 = 32MB SDRAM */ -/* 0x90000004 = 64MB SDRAM */ -#if defined(CONFIG_LCD) -/* set PSC2 in UART mode */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000044 -#else -#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000004 -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x0004fb00 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -/* Quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */ -#define CONFIG_SYS_CS2_START 0x80000000 -#define CONFIG_SYS_CS2_SIZE 0x00001000 -#define CONFIG_SYS_CS2_CFG 0x1d300 - -/* Second Quad UART @0x80010000 */ -#define CONFIG_SYS_CS1_START 0x80010000 -#define CONFIG_SYS_CS1_SIZE 0x00001000 -#define CONFIG_SYS_CS1_CFG 0x1d300 - -/* Leica - build revision resistors */ -/* -#define CONFIG_SYS_CS3_START 0x80020000 -#define CONFIG_SYS_CS3_SIZE 0x00000004 -#define CONFIG_SYS_CS3_CFG 0x1d300 -*/ - -/* - * Select one of quarts as a default - * console. If undefined - PSC console - * wil be default - */ -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/* - * QUART Expanders support - */ -#if defined(CONFIG_QUART_CONSOLE) -/* - * We'll use NS16550 chip routines, - */ -#define CONFIG_SYS_NS16550 1 -#define CONFIG_SYS_NS16550_SERIAL 1 -#define CONFIG_CONS_INDEX 1 -/* - * To achieve necessary offset on SC16C554 - * A0-A2 (register select) pins with NS16550 - * functions (in struct NS16550), REG_SIZE - * should be 4, because A0-A2 pins are connected - * to DA2-DA4 address bus lines. - */ -#define CONFIG_SYS_NS16550_REG_SIZE 4 -/* - * LocalPlus Bus already inited in cpu_init_f(), - * so can work with QUART's chip selects. - * One of four SC16C554 UARTs is selected with - * A3-A4 (DA5-DA6) lines. - */ -#if (CONFIG_QUART_CONSOLE > 0) && (CONFIG_QUART_CONSOLE < 5) && !defined(CONFIG_PRS200) -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS2_START | (CONFIG_QUART_CONSOLE - 1)<<5) -#elif (CONFIG_QUART_CONSOLE > 4) && (CONFIG_QUART_CONSOLE < 9) -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CS1_START | (CONFIG_QUART_CONSOLE - 5)<<5) -#else -#error "Wrong QUART expander number." -#endif - -/* - * SC16C554 chip's external crystal oscillator frequency - * is 7.3728 MHz - */ -#define CONFIG_SYS_NS16550_CLK 7372800 -#endif /* CONFIG_QUART_CONSOLE */ -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00005000 - -#define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */ -#define CONFIG_AUTOBOOT_STOP_STR "432" -#define CONFIG_SILENT_CONSOLE 1 - -#endif /* __CONFIG_H */ diff --git a/include/lcd.h b/include/lcd.h index ea5860c861..020d8800e9 100644 --- a/include/lcd.h +++ b/include/lcd.h @@ -250,7 +250,7 @@ typedef struct vidinfo { void *priv; /* Pointer to driver-specific data */ } vidinfo_t; -#endif /* CONFIG_MPC823, CONFIG_CPU_PXA25X, CONFIG_MCC200, CONFIG_ATMEL_LCD */ +#endif /* CONFIG_MPC823, CONFIG_CPU_PXA25X, CONFIG_ATMEL_LCD */ extern vidinfo_t panel_info; -- 2.25.1