From ec7012e3d8f28b38af023739fdf2f40d1f963604 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 10 Nov 2015 20:53:20 +0100 Subject: [PATCH] eeprom: Zap CONFIG_SYS_EEPROM_X40430 Now that the only user of CONFIG_SYS_EEPROM_X40430 was removed, remove this unused code from cmd_eeprom.c Signed-off-by: Marek Vasut Cc: Tom Rini Cc: Simon Glass Cc: Heiko Schocher Reviewed-by: Heiko Schocher --- common/cmd_eeprom.c | 94 --------------------------------------------- 1 file changed, 94 deletions(-) diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c index 0b59bea01d..266f954e6f 100644 --- a/common/cmd_eeprom.c +++ b/common/cmd_eeprom.c @@ -29,11 +29,6 @@ #define CONFIG_SYS_I2C_SPEED 50000 #endif -/* Maximum number of times to poll for acknowledge after write */ -#if defined(CONFIG_SYS_EEPROM_X40430) -#define MAX_ACKNOWLEDGE_POLLS 10 -#endif - /* * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is * 0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM. @@ -141,14 +136,6 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cn unsigned blk_off; int rcode = 0; -#if defined(CONFIG_SYS_EEPROM_X40430) - uchar contr_r_addr[2]; - uchar addr_void[2]; - uchar contr_reg[2]; - uchar ctrl_reg_v; - int i; -#endif - #if defined(CONFIG_SYS_EEPROM_WREN) eeprom_write_enable (dev_addr,1); #endif @@ -213,88 +200,7 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cn #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C) spi_write (addr, alen, buffer, len); #else -#if defined(CONFIG_SYS_EEPROM_X40430) - /* Get the value of the control register. - * Set current address (internal pointer in the x40430) - * to 0x1ff. - */ - contr_r_addr[0] = 9; - contr_r_addr[1] = 0xff; - addr_void[0] = 0; - addr_void[1] = addr[1]; -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR - contr_r_addr[0] |= CONFIG_SYS_I2C_EEPROM_ADDR; - addr_void[0] |= CONFIG_SYS_I2C_EEPROM_ADDR; -#endif - contr_reg[0] = 0xff; - if (i2c_read (contr_r_addr[0], contr_r_addr[1], 1, contr_reg, 1) != 0) { - rcode = 1; - } - ctrl_reg_v = contr_reg[0]; - /* Are any of the eeprom blocks write protected? - */ - if (ctrl_reg_v & 0x18) { - ctrl_reg_v &= ~0x18; /* reset block protect bits */ - ctrl_reg_v |= 0x02; /* set write enable latch */ - ctrl_reg_v &= ~0x04; /* clear RWEL */ - - /* Set write enable latch. - */ - contr_reg[0] = 0x02; - if (i2c_write (contr_r_addr[0], 0xff, 1, contr_reg, 1) != 0) { - rcode = 1; - } - - /* Set register write enable latch. - */ - contr_reg[0] = 0x06; - if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) { - rcode = 1; - } - - /* Modify ctrl register. - */ - contr_reg[0] = ctrl_reg_v; - if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) { - rcode = 1; - } - - /* The write (above) is an operation on NV memory. - * These can take some time (~5ms), and the device - * will not respond to further I2C messages till - * it's completed the write. - * So poll device for an I2C acknowledge. - * When we get one we know we can continue with other - * operations. - */ - contr_reg[0] = 0; - for (i = 0; i < MAX_ACKNOWLEDGE_POLLS; i++) { - if (i2c_read (addr_void[0], addr_void[1], 1, contr_reg, 1) == 0) - break; /* got ack */ -#if defined(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS) - udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000); -#endif - } - if (i == MAX_ACKNOWLEDGE_POLLS) { - puts ("EEPROM poll acknowledge failed\n"); - rcode = 1; - } - } - - /* Is the write enable latch on?. - */ - else if (!(ctrl_reg_v & 0x02)) { - /* Set write enable latch. - */ - contr_reg[0] = 0x02; - if (i2c_write (contr_r_addr[0], 0xFF, 1, contr_reg, 1) != 0) { - rcode = 1; - } - } - /* Write is enabled ... now write eeprom value. - */ -#endif #if defined(CONFIG_SYS_I2C_EEPROM_BUS) i2c_set_bus_num(CONFIG_SYS_I2C_EEPROM_BUS); #endif -- 2.25.1