From eb9e3651dd1a081e0d908e7e5162d6683098c1f3 Mon Sep 17 00:00:00 2001 From: Gabor Juhos Date: Thu, 18 Jan 2018 13:50:32 +0100 Subject: [PATCH] ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards The patch adds support for the MikroTik RB911-2Hn (911 Lite2) and the RB911-5Hn (911 Lite5) boards: https://mikrotik.com/product/RB911-2Hn https://mikrotik.com/product/RB911-5Hn The two boards are using the same hardware design, the only difference between the two is the supported wireless band. Specifications: * SoC: Atheros AR9344 (600MHz) * RAM: 64MiB * Storage: 16 MiB SPI NOR flash * Ethernet: 1x100M (Passive PoE in) * Wireless: AR9344 built-in wireless MAC, single chain 802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn) Notes: * Older versions of these boards might be equipped with a NAND flash chip instead of the SPI NOR device. Those boards are not supported (yet). * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the same hardware. Support for that can be added later with little effort probably. Installation: 1. Setup a DHCP/BOOTP Server with the following parameters: * DHCP-Option 66 (TFTP server name): pointing to a local TFTP server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename of the to be booted image. The usable intramfs files are: - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin 2. Press the reset button on the board and keep that pressed. 3. Connect the board to your local network via its ethernet port. 4. Release the button after the LEDs on the board are turned off. Now the board should load and start the initramfs image from the TFTP server. 5. Upload the sysupgrade image to the board with scp: $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin 5. Log in to the running system listening on 192.168.1.1 via ssh as root (without password): $ ssh root@192.168.1.1 7. Flash the uploaded firmware file from the ssh session via the sysupgrade command: root@OpenWrt:~# sysupgrade /tmp/fw.bin Signed-off-by: Gabor Juhos --- .../ar71xx/base-files/etc/board.d/01_leds | 4 + .../ar71xx/base-files/etc/board.d/02_network | 2 + target/linux/ar71xx/base-files/etc/diag.sh | 2 + target/linux/ar71xx/base-files/lib/ar71xx.sh | 6 ++ .../ar71xx/base-files/lib/upgrade/platform.sh | 4 + .../files/arch/mips/ath79/Kconfig.openwrt | 2 + .../ar71xx/files/arch/mips/ath79/mach-rbspi.c | 97 +++++++++++++++++++ .../ar71xx/files/arch/mips/ath79/machtypes.h | 1 + target/linux/ar71xx/image/mikrotik.mk | 2 +- ...MIPS-ath79-add-routerboard-detection.patch | 3 +- ...MIPS-ath79-add-routerboard-detection.patch | 3 +- 11 files changed, 123 insertions(+), 3 deletions(-) diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index fb1f29dcfa..ecd3723c6a 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -292,6 +292,10 @@ rb-750up-r2) ucidef_set_led_switch "port4" "port3" "rb:green:port4" "switch0" "0x04" ucidef_set_led_switch "port5" "port5" "rb:green:port5" "switch0" "0x02" ;; +rb-911-2hn|\ +rb-911-5hn) + ucidef_set_led_netdev "eth" "ETH" "rb:green:eth" "eth0" + ;; rb-941-2nd) ucidef_set_led_timer "user" "USR/ACT" "rb:green:user" "1000" "1000" ;; diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index 5a10a9f486..b0755c44dd 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -93,6 +93,8 @@ ar71xx_setup_interfaces() pqi-air-pen|\ rb-411|\ rb-411u|\ + rb-911-2hn|\ + rb-911-5hn|\ rb-911g-2hpnd|\ rb-911g-5hpacd|\ rb-911g-5hpnd|\ diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 2720288e3d..4f4a73ce06 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -319,6 +319,8 @@ get_status_led() { rb-750-r2|\ rb-750p-pbr2|\ rb-750up-r2|\ + rb-911-2hn|\ + rb-911-5hn|\ rb-911g-2hpnd|\ rb-911g-5hpacd|\ rb-911g-5hpnd|\ diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index b6642495de..73bdce5853 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -941,6 +941,12 @@ ar71xx_board_detect() { *"RouterBOARD 751G") name="rb-751g" ;; + *"RouterBOARD 911-2Hn") + name="rb-911-2hn" + ;; + *"RouterBOARD 911-5Hn") + name="rb-911-5hn" + ;; *"RouterBOARD 911G-2HPnD") name="rb-911g-2hpnd" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 3d7b1593e1..1f9ed76fc3 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -660,6 +660,8 @@ platform_check_image() { rb-750-r2|\ rb-750p-pbr2|\ rb-750up-r2|\ + rb-911-2hn|\ + rb-911-5hn|\ rb-941-2nd|\ rb-951ui-2nd|\ rb-952ui-5ac2nd|\ @@ -723,6 +725,8 @@ platform_pre_upgrade() { rb-750-r2|\ rb-750p-pbr2|\ rb-750up-r2|\ + rb-911-2hn|\ + rb-911-5hn|\ rb-941-2nd|\ rb-951ui-2nd|\ rb-952ui-5ac2nd|\ diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 3ca77550bc..caaaf97792 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -1054,6 +1054,8 @@ config ATH79_MACH_RBSPI select ATH79_ROUTERBOOT help Say 'Y' here if you want your kernel to support the + MikroTik ROuterBOARD 911-2Hn (911 Lite2) + MikroTik ROuterBOARD 911-5Hn (911 Lite5) MikroTik RouterBOARD mAP MikroTik RouterBOARD mAP lite MikroTik RouterBOARD hAP lite diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-rbspi.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-rbspi.c index 25e920f593..f7f3b028f4 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/mach-rbspi.c +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-rbspi.c @@ -3,6 +3,8 @@ * * - MikroTik RouterBOARD mAP 2nD * - MikroTik RouterBOARD mAP L-2nD + * - MikroTik RouterBOARD 911-2Hn (911 Lite2) + * - MikroTik RouterBOARD 911-5Hn (911 Lite5) * - MikroTik RouterBOARD 941L-2nD * - MikroTik RouterBOARD 951Ui-2nD * - MikroTik RouterBOARD 952Ui-5ac2nD @@ -509,6 +511,56 @@ static struct platform_device rbwapgsc_phy_device = { }, }; +/* RB911L GPIOs */ +#define RB911L_GPIO_BTN_RESET 15 +#define RB911L_GPIO_LED_1 13 +#define RB911L_GPIO_LED_2 12 +#define RB911L_GPIO_LED_3 4 +#define RB911L_GPIO_LED_4 21 +#define RB911L_GPIO_LED_5 18 +#define RB911L_GPIO_LED_ETH 20 +#define RB911L_GPIO_LED_POWER 11 +#define RB911L_GPIO_LED_USER 3 +#define RB911L_GPIO_PIN_HOLE 14 /* for reference */ + +static struct gpio_led rb911l_leds[] __initdata = { + { + .name = "rb:green:eth", + .gpio = RB911L_GPIO_LED_ETH, + .active_low = 1, + }, { + .name = "rb:green:led1", + .gpio = RB911L_GPIO_LED_1, + .active_low = 1, + }, { + .name = "rb:green:led2", + .gpio = RB911L_GPIO_LED_2, + .active_low = 1, + }, { + .name = "rb:green:led3", + .gpio = RB911L_GPIO_LED_3, + .active_low = 1, + }, { + .name = "rb:green:led4", + .gpio = RB911L_GPIO_LED_4, + .active_low = 1, + }, { + .name = "rb:green:led5", + .gpio = RB911L_GPIO_LED_5, + .active_low = 1, + }, { + .name = "rb:green:power", + .gpio = RB911L_GPIO_LED_POWER, + .default_state = LEDS_GPIO_DEFSTATE_ON, + .open_drain = 1, + }, { + .name = "rb:green:user", + .gpio = RB911L_GPIO_LED_USER, + .active_low = 1, + .open_drain = 1, + }, +}; + static struct gen_74x164_chip_platform_data rbspi_ssr_data = { .base = RBSPI_SSR_GPIO_BASE, .num_registers = 1, @@ -1015,8 +1067,53 @@ static void __init rbwapgsc_setup(void) rbwapgsc_leds); } +/* + * Setup the 911L hardware (AR9344). + */ +static void __init rb911l_setup(void) +{ + const struct rb_info *info; + + info = rbspi_platform_setup(); + if (!info) + return; + + if (!rb_has_hw_option(info, RB_HW_OPT_NO_NAND)) { + /* + * Old hardware revisions might be equipped with a NAND flash + * chip instead of the 16MiB SPI NOR device. Those boards are + * not supported at the moment, so throw a warning and skip + * the peripheral setup to avoid messing up the data in the + * flash chip. + */ + WARN(1, "The NAND flash on this board is not supported.\n"); + } else { + rbspi_peripherals_setup(0); + } + + ath79_register_mdio(1, 0x0); + + ath79_init_mac(ath79_eth1_data.mac_addr, ath79_mac_base, 0); + + ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII; + ath79_eth1_data.speed = SPEED_1000; + ath79_eth1_data.duplex = DUPLEX_FULL; + + ath79_register_eth(1); + + rbspi_wlan_init(0, 1); + + rbspi_register_reset_button(RB911L_GPIO_BTN_RESET); + + /* Make the eth LED controllable by software. */ + ath79_gpio_output_select(RB911L_GPIO_LED_ETH, AR934X_GPIO_OUT_GPIO); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(rb911l_leds), rb911l_leds); +} + MIPS_MACHINE_NONAME(ATH79_MACH_RB_MAPL, "map-hb", rbmapl_setup); MIPS_MACHINE_NONAME(ATH79_MACH_RB_941, "H951L", rbhapl_setup); +MIPS_MACHINE_NONAME(ATH79_MACH_RB_911L, "911L", rb911l_setup); MIPS_MACHINE_NONAME(ATH79_MACH_RB_952, "952-hb", rb952_setup); MIPS_MACHINE_NONAME(ATH79_MACH_RB_962, "962", rb962_setup); MIPS_MACHINE_NONAME(ATH79_MACH_RB_750UPR2, "750-hb", rb750upr2_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index a621fe2c90..394be00c99 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -190,6 +190,7 @@ enum ath79_mach_type { ATH79_MACH_RB_750UPR2, /* MikroTik RouterBOARD 750UP r2 */ ATH79_MACH_RB_751, /* MikroTik RouterBOARD 751 */ ATH79_MACH_RB_751G, /* Mikrotik RouterBOARD 751G */ + ATH79_MACH_RB_911L, /* Mikrotik RouterBOARD 911-2Hn/911-5Hn boards */ ATH79_MACH_RB_922GS, /* Mikrotik RouterBOARD 911/922GS boards */ ATH79_MACH_RB_941, /* MikroTik RouterBOARD 941-2nD */ ATH79_MACH_RB_951G, /* Mikrotik RouterBOARD 951G */ diff --git a/target/linux/ar71xx/image/mikrotik.mk b/target/linux/ar71xx/image/mikrotik.mk index 403bcb08b5..f381f85ae2 100644 --- a/target/linux/ar71xx/image/mikrotik.mk +++ b/target/linux/ar71xx/image/mikrotik.mk @@ -40,7 +40,7 @@ define Device/rb-nor-flash-16M LOADER_TYPE := elf KERNEL_INSTALL := 1 KERNEL := kernel-bin | lzma | loader-kernel - SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-750p-pbr2 rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-map-2nd rb-mapl-2nd rb-wap-2nd + SUPPORTED_DEVICES := rb-750-r2 rb-750up-r2 rb-750p-pbr2 rb-911-2hn rb-911-5hn rb-941-2nd rb-951ui-2nd rb-952ui-5ac2nd rb-962uigs-5hact2hnt rb-lhg-5nd rb-map-2nd rb-mapl-2nd rb-wap-2nd IMAGE/sysupgrade.bin := append-kernel | kernel2minor -s 1024 -e | pad-to $$$$(BLOCKSIZE) | \ append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE) endef diff --git a/target/linux/ar71xx/patches-4.4/701-MIPS-ath79-add-routerboard-detection.patch b/target/linux/ar71xx/patches-4.4/701-MIPS-ath79-add-routerboard-detection.patch index 625bb19ba5..64c7e881a7 100644 --- a/target/linux/ar71xx/patches-4.4/701-MIPS-ath79-add-routerboard-detection.patch +++ b/target/linux/ar71xx/patches-4.4/701-MIPS-ath79-add-routerboard-detection.patch @@ -1,6 +1,6 @@ --- a/arch/mips/ath79/prom.c +++ b/arch/mips/ath79/prom.c -@@ -136,6 +136,30 @@ void __init prom_init(void) +@@ -136,6 +136,31 @@ void __init prom_init(void) initrd_end = initrd_start + fw_getenvl("initrd_size"); } #endif @@ -26,6 +26,7 @@ + strstr(arcs_cmdline, "board=2011L") || + strstr(arcs_cmdline, "board=2011r") || + strstr(arcs_cmdline, "board=711Gr100") || ++ strstr(arcs_cmdline, "board=911L") || + strstr(arcs_cmdline, "board=922gs")) + ath79_prom_append_cmdline("console", "ttyS0,115200"); } diff --git a/target/linux/ar71xx/patches-4.9/701-MIPS-ath79-add-routerboard-detection.patch b/target/linux/ar71xx/patches-4.9/701-MIPS-ath79-add-routerboard-detection.patch index 625bb19ba5..64c7e881a7 100644 --- a/target/linux/ar71xx/patches-4.9/701-MIPS-ath79-add-routerboard-detection.patch +++ b/target/linux/ar71xx/patches-4.9/701-MIPS-ath79-add-routerboard-detection.patch @@ -1,6 +1,6 @@ --- a/arch/mips/ath79/prom.c +++ b/arch/mips/ath79/prom.c -@@ -136,6 +136,30 @@ void __init prom_init(void) +@@ -136,6 +136,31 @@ void __init prom_init(void) initrd_end = initrd_start + fw_getenvl("initrd_size"); } #endif @@ -26,6 +26,7 @@ + strstr(arcs_cmdline, "board=2011L") || + strstr(arcs_cmdline, "board=2011r") || + strstr(arcs_cmdline, "board=711Gr100") || ++ strstr(arcs_cmdline, "board=911L") || + strstr(arcs_cmdline, "board=922gs")) + ath79_prom_append_cmdline("console", "ttyS0,115200"); } -- 2.25.1