From e6bd72f880a76652ce1d6742880e7efcd85b8fb1 Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Fri, 1 May 2020 20:04:17 +0800 Subject: [PATCH] dm: ppc: T4240: add i2c DM support This supports i2c DM for SoC T4240 Signed-off-by: Biwen Li Reviewed-by: Priyanka Jain --- arch/powerpc/dts/t4240.dtsi | 5 +- board/freescale/common/vsc3316_3308.c | 258 +++++++++++++++++++++++++- board/freescale/t4qds/t4240qds.c | 45 ++++- include/configs/T4240QDS.h | 13 ++ include/configs/T4240RDB.h | 9 +- 5 files changed, 320 insertions(+), 10 deletions(-) diff --git a/arch/powerpc/dts/t4240.dtsi b/arch/powerpc/dts/t4240.dtsi index 43f98cd9e1..9b5902fe9e 100644 --- a/arch/powerpc/dts/t4240.dtsi +++ b/arch/powerpc/dts/t4240.dtsi @@ -3,7 +3,7 @@ * T4240 Silicon/SoC Device Tree Source (pre include) * * Copyright 2013 Freescale Semiconductor Inc. - * Copyright 2019 NXP + * Copyright 2019-2020 NXP */ /dts-v1/; @@ -125,6 +125,9 @@ reg = <0x114000 0x1000>; clock-frequency = <0>; }; + + /include/ "qoriq-i2c-0.dtsi" + /include/ "qoriq-i2c-1.dtsi" }; pcie@ffe240000 { diff --git a/board/freescale/common/vsc3316_3308.c b/board/freescale/common/vsc3316_3308.c index 033fae020f..f0d273ca20 100644 --- a/board/freescale/common/vsc3316_3308.c +++ b/board/freescale/common/vsc3316_3308.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2020 NXP */ #include "vsc3316_3308.h" @@ -32,7 +33,22 @@ int vsc_if_enable(unsigned int vsc_addr) /* enable 2-wire Serial InterFace (I2C) */ data = 0x02; +#ifdef CONFIG_DM_I2C + int ret, bus_num = 0; + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + + return dm_i2c_write(dev, INTERFACE_MODE_REG, &data, 1); +#else return i2c_write(vsc_addr, INTERFACE_MODE_REG, 1, &data, 1); +#endif } int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], @@ -45,6 +61,66 @@ int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], debug("VSC:Initializing VSC3316 at I2C address 0x%2x" " for Tx\n", vsc_addr); +#ifdef CONFIG_DM_I2C + int bus_num = 0; + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + + ret = dm_i2c_read(dev, REVISION_ID_REG, &rev_id, 1); + if (ret < 0) { + printf("VSC:0x%x could not read REV_ID from device.\n", + vsc_addr); + return ret; + } + + if (rev_id != 0xab) { + printf("VSC: device at address 0x%x is not VSC3316/3308.\n", + vsc_addr); + return -ENODEV; + } + + ret = vsc_if_enable(vsc_addr); + if (ret) { + printf("VSC:0x%x could not configured for 2-wire I/F.\n", + vsc_addr); + return ret; + } + + /* config connections - page 0x00 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); + + /* Making crosspoint connections, by connecting required + * input to output + */ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][1], con_arr[i][0]); + + /* input state - page 0x13 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); + /* Configuring the required input of the switch */ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][0], 0x80); + + /* Setting Global Input LOS threshold value */ + dm_i2c_reg_write(dev, GLOBAL_INPUT_LOS, 0x60); + + /* config output mode - page 0x23 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); + /* Turn ON the Output driver correspond to required output*/ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][1], 0); + + /* configure global core control register, Turn on Global core power */ + dm_i2c_reg_write(dev, GLOBAL_CORE_CNTRL, 0); + +#else ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); if (ret < 0) { printf("VSC:0x%x could not read REV_ID from device.\n", @@ -90,6 +166,7 @@ int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2], /* configure global core control register, Turn on Global core power */ i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); +#endif vsc_wp_config(vsc_addr); @@ -107,6 +184,105 @@ int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2], debug("VSC:Initializing VSC3308 at I2C address 0x%x for Tx\n", vsc_addr); +#ifdef CONFIG_DM_I2C + int bus_num = 0; + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + + ret = dm_i2c_read(dev, REVISION_ID_REG, &rev_id, 1); + if (ret < 0) { + printf("VSC:0x%x could not read REV_ID from device.\n", + vsc_addr); + return ret; + } + + if (rev_id != 0xab) { + printf("VSC: device at address 0x%x is not VSC3316/3308.\n", + vsc_addr); + return -ENODEV; + } + + ret = vsc_if_enable(vsc_addr); + if (ret) { + printf("VSC:0x%x could not configured for 2-wire I/F.\n", + vsc_addr); + return ret; + } + + /* config connections - page 0x00 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); + + /* Configure Global Input ISE */ + dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE1, 0); + dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE2, 0); + + /* Configure Tx/Rx Global Output PE1 */ + dm_i2c_reg_write(dev, GLOBAL_OUTPUT_PE1, 0); + + /* Configure Tx/Rx Global Output PE2 */ + dm_i2c_reg_write(dev, GLOBAL_OUTPUT_PE2, 0); + + /* Configure Tx/Rx Global Input GAIN */ + dm_i2c_reg_write(dev, GLOBAL_INPUT_GAIN, 0x3F); + + /* Setting Global Input LOS threshold value */ + dm_i2c_reg_write(dev, GLOBAL_INPUT_LOS, 0xE0); + + /* Setting Global output termination */ + dm_i2c_reg_write(dev, GLOBAL_OUTPUT_TERMINATION, 0); + + /* Configure Tx/Rx Global Output level */ + if (vsc_addr == VSC3308_TX_ADDRESS) + dm_i2c_reg_write(dev, GLOBAL_OUTPUT_LEVEL, 4); + else + dm_i2c_reg_write(dev, GLOBAL_OUTPUT_LEVEL, 2); + + /* Making crosspoint connections, by connecting required + * input to output + */ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][1], con_arr[i][0]); + + /* input state - page 0x13 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); + /* Turning off all the required input of the switch */ + for (i = 0; i < num_con; i++) + dm_i2c_reg_write(dev, con_arr[i][0], 1); + + /* only turn on specific Tx/Rx requested by the XFI erratum */ + if (vsc_addr == VSC3308_TX_ADDRESS) { + dm_i2c_reg_write(dev, 2, 0); + dm_i2c_reg_write(dev, 3, 0); + } else { + dm_i2c_reg_write(dev, 0, 0); + dm_i2c_reg_write(dev, 1, 0); + } + + /* config output mode - page 0x23 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); + /* Turn off the Output driver correspond to required output*/ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][1], 1); + + /* only turn on specific Tx/Rx requested by the XFI erratum */ + if (vsc_addr == VSC3308_TX_ADDRESS) { + dm_i2c_reg_write(dev, 0, 0); + dm_i2c_reg_write(dev, 1, 0); + } else { + dm_i2c_reg_write(dev, 3, 0); + dm_i2c_reg_write(dev, 4, 0); + } + + /* configure global core control register, Turn on Global core power */ + dm_i2c_reg_write(dev, GLOBAL_CORE_CNTRL, 0); +#else ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); if (ret < 0) { printf("VSC:0x%x could not read REV_ID from device.\n", @@ -192,7 +368,7 @@ int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2], /* configure global core control register, Turn on Global core power */ i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); - +#endif vsc_wp_config(vsc_addr); return 0; @@ -208,7 +384,69 @@ int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2], debug("VSC:Initializing VSC3308 at I2C address 0x%x" " for Tx\n", vsc_addr); +#ifdef CONFIG_DM_I2C + int bus_num = 0; + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + ret = dm_i2c_read(dev, REVISION_ID_REG, &rev_id, 1); + if (ret < 0) { + printf("VSC:0x%x could not read REV_ID from device.\n", + vsc_addr); + return ret; + } + + if (rev_id != 0xab) { + printf("VSC: device at address 0x%x is not VSC3316/3308.\n", + vsc_addr); + return -ENODEV; + } + + ret = vsc_if_enable(vsc_addr); + if (ret) { + printf("VSC:0x%x could not configured for 2-wire I/F.\n", + vsc_addr); + return ret; + } + + /* config connections - page 0x00 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE); + + /* Making crosspoint connections, by connecting required + * input to output + */ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][1], con_arr[i][0]); + + /*Configure Global Input ISE and gain */ + dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE1, 0x12); + dm_i2c_reg_write(dev, GLOBAL_INPUT_ISE2, 0x12); + + /* input state - page 0x13 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, INPUT_STATE_REG); + /* Turning ON the required input of the switch */ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][0], 0); + + /* Setting Global Input LOS threshold value */ + dm_i2c_reg_write(dev, GLOBAL_INPUT_LOS, 0x60); + + /* config output mode - page 0x23 */ + dm_i2c_reg_write(dev, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE); + /* Turn ON the Output driver correspond to required output*/ + for (i = 0; i < num_con ; i++) + dm_i2c_reg_write(dev, con_arr[i][1], 0); + + /* configure global core control register, Turn on Global core power */ + dm_i2c_reg_write(dev, GLOBAL_CORE_CNTRL, 0); +#else ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1); if (ret < 0) { printf("VSC:0x%x could not read REV_ID from device.\n", @@ -258,7 +496,7 @@ int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2], /* configure global core control register, Turn on Global core power */ i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0); - +#endif vsc_wp_config(vsc_addr); return 0; @@ -270,6 +508,22 @@ void vsc_wp_config(unsigned int vsc_addr) /* For new crosspoint configuration to occur, WP bit of * CORE_CONFIG_REG should be set 1 and then reset to 0 */ +#ifdef CONFIG_DM_I2C + int ret, bus_num = 0; + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(bus_num, vsc_addr, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return; + } + + dm_i2c_reg_write(dev, CORE_CONFIG_REG, 0x01); + dm_i2c_reg_write(dev, CORE_CONFIG_REG, 0x0); +#else i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x01); i2c_reg_write(vsc_addr, CORE_CONFIG_REG, 0x0); +#endif } diff --git a/board/freescale/t4qds/t4240qds.c b/board/freescale/t4qds/t4240qds.c index 5608774afd..869c01de92 100644 --- a/board/freescale/t4qds/t4240qds.c +++ b/board/freescale/t4qds/t4240qds.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0+ /* * Copyright 2009-2012 Freescale Semiconductor, Inc. + * Copyright 2020 NXP */ #include @@ -91,11 +92,25 @@ int checkboard(void) return 0; } -int select_i2c_ch_pca9547(u8 ch) +int select_i2c_ch_pca9547(u8 ch, int bus_num) { int ret; +#ifdef CONFIG_DM_I2C + struct udevice *dev; + + ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + + ret = dm_i2c_write(dev, 0, &ch, 1); +#else ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); +#endif if (ret) { puts("PCA: failed to select proper channel\n"); return ret; @@ -115,10 +130,28 @@ static inline int read_voltage(void) { int i, ret, voltage_read = 0; u16 vol_mon; +#ifdef CONFIG_DM_I2C + struct udevice *dev; + int bus_num = 0; +#endif for (i = 0; i < NUM_READINGS; i++) { +#ifdef CONFIG_DM_I2C + ret = i2c_get_chip_for_busnum(bus_num, I2C_VOL_MONITOR_ADDR, + 1, &dev); + if (ret) { + printf("%s: Cannot find udev for a bus %d\n", __func__, + bus_num); + return ret; + } + + ret = dm_i2c_read(dev, + I2C_VOL_MONITOR_BUS_V_OFFSET, + (void *)&vol_mon, 2); +#else ret = i2c_read(I2C_VOL_MONITOR_ADDR, I2C_VOL_MONITOR_BUS_V_OFFSET, 1, (void *)&vol_mon, 2); +#endif if (ret) { printf("VID: failed to read core voltage\n"); return ret; @@ -250,7 +283,7 @@ static int adjust_vdd(ulong vdd_override) unsigned voltage; }; - ret = select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR); + ret = select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR, 0); if (ret) { debug("VID: I2c failed to switch channel\n"); ret = -1; @@ -348,7 +381,7 @@ int config_frontside_crossbar_vsc3316(void) u32 srds_prtcl_s1, srds_prtcl_s2; int ret; - ret = select_i2c_ch_pca9547(I2C_MUX_CH_VSC3316_FS); + ret = select_i2c_ch_pca9547(I2C_MUX_CH_VSC3316_FS, 0); if (ret) return ret; @@ -567,7 +600,7 @@ int board_early_init_r(void) /* Configure board SERDES ports crossbar */ config_frontside_crossbar_vsc3316(); config_backside_crossbar_mux(); - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0); return 0; } @@ -732,11 +765,11 @@ void board_detail(void) } /* Voltage secion */ - if (!select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR)) { + if (!select_i2c_ch_pca9547(I2C_MUX_CH_VOL_MONITOR, 0)) { vdd = read_voltage(); if (vdd > 0) printf("Core voltage= %d mV\n", vdd); - select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0); } printf("XVDD = 1.%d V\n", ((brdcfg[8] & 0xf) - 4) * 5 + 25); diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h index 91a7c70356..5f91a52bbe 100644 --- a/include/configs/T4240QDS.h +++ b/include/configs/T4240QDS.h @@ -280,6 +280,19 @@ unsigned long get_board_ddr_clk(void); #endif /* I2C */ +#ifndef CONFIG_DM_I2C +#define CONFIG_SYS_I2C +#else +#undef CONFIG_SYS_I2C +#undef CONFIG_SYS_FSL_I2C2_OFFSET +#undef CONFIG_SYS_FSL_I2C2_SLAVE +#undef CONFIG_SYS_FSL_I2C2_SPEED +#undef CONFIG_SYS_FSL_I2C_SLAVE +#undef CONFIG_SYS_FSL_I2C_SPEED +#undef CONFIG_SYS_FSL_I2C_OFFSET +#endif + +#define CONFIG_SYS_I2C_FSL #define CONFIG_SYS_FSL_I2C_SPEED 100000 /* I2C speed */ #define CONFIG_SYS_FSL_I2C2_SPEED 100000 /* I2C2 speed */ #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h index 31cb1cf34a..ce7634f4ea 100644 --- a/include/configs/T4240RDB.h +++ b/include/configs/T4240RDB.h @@ -1,6 +1,7 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2014 Freescale Semiconductor, Inc. + * Copyright 2020 NXP */ /* @@ -159,12 +160,18 @@ #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) /* I2C */ +#ifndef CONFIG_DM_I2C #define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100 +#else +#define CONFIG_I2C_SET_DEFAULT_BUS_NUM +#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0 +#endif + +#define CONFIG_SYS_I2C_FSL /* * General PCI -- 2.25.1