From d1a4aafd71991a3ddff97f7b6ec91b0952e2f4b6 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Wed, 6 Aug 2014 12:59:52 +0900 Subject: [PATCH] powerpc: mpc8xx: remove svm_sc8xx board This board has been orphaned for a while and old enough. Signed-off-by: Masahiro Yamada --- arch/powerpc/cpu/mpc8xx/Kconfig | 4 - arch/powerpc/cpu/mpc8xx/cpu_init.c | 4 - board/svm_sc8xx/Kconfig | 11 - board/svm_sc8xx/MAINTAINERS | 6 - board/svm_sc8xx/Makefile | 8 - board/svm_sc8xx/flash.c | 666 ----------------------------- board/svm_sc8xx/svm_sc8xx.c | 144 ------- board/svm_sc8xx/u-boot.lds | 99 ----- board/svm_sc8xx/u-boot.lds.debug | 114 ----- configs/svm_sc8xx_defconfig | 3 - doc/README.scrapyard | 1 + drivers/pcmcia/tqm8xx_pcmcia.c | 6 +- include/commproc.h | 51 --- include/configs/svm_sc8xx.h | 450 ------------------- include/pcmcia.h | 2 +- include/status_led.h | 14 - 16 files changed, 4 insertions(+), 1579 deletions(-) delete mode 100644 board/svm_sc8xx/Kconfig delete mode 100644 board/svm_sc8xx/MAINTAINERS delete mode 100644 board/svm_sc8xx/Makefile delete mode 100644 board/svm_sc8xx/flash.c delete mode 100644 board/svm_sc8xx/svm_sc8xx.c delete mode 100644 board/svm_sc8xx/u-boot.lds delete mode 100644 board/svm_sc8xx/u-boot.lds.debug delete mode 100644 configs/svm_sc8xx_defconfig delete mode 100644 include/configs/svm_sc8xx.h diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig index ae97f302d2..6392c55c20 100644 --- a/arch/powerpc/cpu/mpc8xx/Kconfig +++ b/arch/powerpc/cpu/mpc8xx/Kconfig @@ -53,9 +53,6 @@ config TARGET_SXNI855T config TARGET_SPD823TS bool "Support SPD823TS" -config TARGET_SVM_SC8XX - bool "Support svm_sc8xx" - config TARGET_MHPC bool "Support MHPC" @@ -150,7 +147,6 @@ source "board/netvia/Kconfig" source "board/r360mpi/Kconfig" source "board/sixnet/Kconfig" source "board/spd8xx/Kconfig" -source "board/svm_sc8xx/Kconfig" source "board/tqc/tqm8xx/Kconfig" endmenu diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c index e51fec7260..90c7e61d83 100644 --- a/arch/powerpc/cpu/mpc8xx/cpu_init.c +++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c @@ -44,11 +44,7 @@ void cpu_init_f (volatile immap_t * immr) #endif /* CONFIG_WATCHDOG */ /* SIUMCR - contains debug pin configuration (11-6) */ -#ifndef CONFIG_SVM_SC8xx immr->im_siu_conf.sc_siumcr |= CONFIG_SYS_SIUMCR; -#else - immr->im_siu_conf.sc_siumcr = CONFIG_SYS_SIUMCR; -#endif /* initialize timebase status and control register (11-26) */ /* unlock TBSCRK */ diff --git a/board/svm_sc8xx/Kconfig b/board/svm_sc8xx/Kconfig deleted file mode 100644 index 522b1a85d0..0000000000 --- a/board/svm_sc8xx/Kconfig +++ /dev/null @@ -1,11 +0,0 @@ -if TARGET_SVM_SC8XX - -config SYS_BOARD - string - default "svm_sc8xx" - -config SYS_CONFIG_NAME - string - default "svm_sc8xx" - -endif diff --git a/board/svm_sc8xx/MAINTAINERS b/board/svm_sc8xx/MAINTAINERS deleted file mode 100644 index c19bcae2b2..0000000000 --- a/board/svm_sc8xx/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -SVM_SC8XX BOARD -M: John Zhan -S: Orphan (since 2014-06) -F: board/svm_sc8xx/ -F: include/configs/svm_sc8xx.h -F: configs/svm_sc8xx_defconfig diff --git a/board/svm_sc8xx/Makefile b/board/svm_sc8xx/Makefile deleted file mode 100644 index 4c0b4a33e9..0000000000 --- a/board/svm_sc8xx/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y = svm_sc8xx.o flash.o diff --git a/board/svm_sc8xx/flash.c b/board/svm_sc8xx/flash.c deleted file mode 100644 index 8a04de80b3..0000000000 --- a/board/svm_sc8xx/flash.c +++ /dev/null @@ -1,666 +0,0 @@ -/* - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -#ifndef CONFIG_ENV_ADDR -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) -#endif - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - -/*----------------------------------------------------------------------- - * Functions - */ -static int write_word(flash_info_t *info, ulong dest, ulong data); - -#ifdef CONFIG_BOOT_8B -static int my_in_8(unsigned char *addr); -static void my_out_8(unsigned char *addr, int val); -#endif -#ifdef CONFIG_BOOT_16B -static int my_in_be16(unsigned short *addr); -static void my_out_be16(unsigned short *addr, int val); -#endif -#ifdef CONFIG_BOOT_32B -static unsigned my_in_be32(unsigned *addr); -static void my_out_be32(unsigned *addr, int val); -#endif -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init(void) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - unsigned long size_b0, size_b1; - int i; - - size_b0 = 0; - size_b1 = 0; - /* Init: no FLASHes known */ - for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) - flash_info[i].flash_id = FLASH_UNKNOWN; - -#ifdef CONFIG_SYS_DOC_BASE -#ifndef CONFIG_FEL8xx_AT - /* 32k bytes */ - memctl->memc_or5 = (0xffff8000 | CONFIG_SYS_OR_TIMING_DOC); - memctl->memc_br5 = CONFIG_SYS_DOC_BASE | 0x401; -#else - /* 32k bytes */ - memctl->memc_or3 = (0xffff8000 | CONFIG_SYS_OR_TIMING_DOC); - memctl->memc_br3 = CONFIG_SYS_DOC_BASE | 0x401; -#endif -#endif -#if defined(CONFIG_BOOT_8B) - size_b0 = 0x80000; /* 512 K */ - - flash_info[0].flash_id = FLASH_MAN_AMD | FLASH_AM040; - flash_info[0].sector_count = 8; - flash_info[0].size = 0x00080000; - - /* set up sector start address table */ - for (i = 0; i < flash_info[0].sector_count; i++) - flash_info[0].start[i] = 0x40000000 + (i * 0x10000); - - /* protect all sectors */ - for (i = 0; i < flash_info[0].sector_count; i++) - flash_info[0].protect[i] = 0x1; - -#elif defined(CONFIG_BOOT_16B) - size_b0 = 0x400000; /* 4MB , assume AMD29LV320B */ - - flash_info[0].flash_id = FLASH_MAN_AMD | FLASH_AM320B; - flash_info[0].sector_count = 67; - flash_info[0].size = 0x00400000; - - /* set up sector start address table */ - flash_info[0].start[0] = 0x40000000; - flash_info[0].start[1] = 0x40000000 + 0x4000; - flash_info[0].start[2] = 0x40000000 + 0x6000; - flash_info[0].start[3] = 0x40000000 + 0x8000; - - for (i = 4; i < flash_info[0].sector_count; i++) { - flash_info[0].start[i] = - 0x40000000 + 0x10000 + ((i - 4) * 0x10000); - } - - /* protect all sectors */ - for (i = 0; i < flash_info[0].sector_count; i++) - flash_info[0].protect[i] = 0x1; -#endif - -#ifdef CONFIG_BOOT_32B - - /* Static FLASH Bank configuration here - FIXME XXX */ - size_b0 = flash_get_size((vu_long *) FLASH_BASE0_PRELIM, - &flash_info[0]); - - if (flash_info[0].flash_id == FLASH_UNKNOWN) { - printf("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n", - size_b0, size_b0 << 20); - } - - size_b1 = flash_get_size((vu_long *) FLASH_BASE1_PRELIM, - &flash_info[1]); - - if (size_b1 > size_b0) { - printf("## ERROR: " - "Bank 1 (0x%08lx = %ld MB) > Bank 0 (0x%08lx = %ld MB)\n", - size_b1, size_b1 << 20, size_b0, size_b0 << 20); - flash_info[0].flash_id = FLASH_UNKNOWN; - flash_info[1].flash_id = FLASH_UNKNOWN; - flash_info[0].sector_count = -1; - flash_info[1].sector_count = -1; - flash_info[0].size = 0; - flash_info[1].size = 0; - - return 0; - } - - /* Remap FLASH according to real size */ - memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH | - (-size_b0 & OR_AM_MSK); - memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | - BR_MS_GPCM | BR_V; - - /* Re-do sizing to get full correct info */ - size_b0 = flash_get_size((vu_long *) CONFIG_SYS_FLASH_BASE, - &flash_info[0]); - - flash_get_offsets(CONFIG_SYS_FLASH_BASE, &flash_info[0]); - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE - /* monitor protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, - &flash_info[0]); -#endif - -#ifdef CONFIG_ENV_IS_IN_FLASH - /* ENV protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, &flash_info[0]); -#endif - - if (size_b1) { - memctl->memc_or1 = CONFIG_SYS_OR_TIMING_FLASH | - (-size_b1 & 0xFFFF8000); - memctl->memc_br1 = ((CONFIG_SYS_FLASH_BASE + - size_b0) & BR_BA_MSK) | BR_MS_GPCM | BR_V; - - /* Re-do sizing to get full correct info */ - size_b1 = flash_get_size((vu_long *)(CONFIG_SYS_FLASH_BASE + - size_b0), &flash_info[1]); - - flash_get_offsets(CONFIG_SYS_FLASH_BASE + size_b0, - &flash_info[1]); - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE - /* monitor protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, - &flash_info[1]); -#endif - -#ifdef CONFIG_ENV_IS_IN_FLASH - /* ENV protection ON by default */ - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, - &flash_info[1]); -#endif - } else { - memctl->memc_br1 = 0; /* invalidate bank */ - - flash_info[1].flash_id = FLASH_UNKNOWN; - flash_info[1].sector_count = -1; - } - - flash_info[0].size = size_b0; - flash_info[1].size = size_b1; - - -#endif /* CONFIG_BOOT_32B */ - - return size_b0 + size_b1; -} - - -void flash_print_info(flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_AMD: - printf("AMD "); - break; - case FLASH_MAN_FUJ: - printf("FUJITSU "); - break; - default: - printf("Unknown Vendor "); - break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_AM400B: - printf("AM29LV400B (4 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM400T: - printf("AM29LV400T (4 Mbit, top boot sector)\n"); - break; - case FLASH_AM800B: - printf("AM29LV800B (8 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM800T: - printf("AM29LV800T (8 Mbit, top boot sector)\n"); - break; - case FLASH_AM160B: - printf("AM29LV160B (16 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM160T: - printf("AM29LV160T (16 Mbit, top boot sector)\n"); - break; - case FLASH_AM320B: - printf("AM29LV320B (32 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM320T: - printf("AM29LV320T (32 Mbit, top boot sector)\n"); - break; - default: - printf("Unknown Chip Type\n"); - break; - } - - printf(" Size: %ld MB in %d Sectors\n", - info->size >> 20, info->sector_count); - - printf(" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; ++i) { - if ((i % 5) == 0) - printf("\n "); - printf(" %08lX%s", - info->start[i], info->protect[i] ? " (RO)" : " "); - } - printf("\n"); - return; -} - -/* - * The following code cannot be run from FLASH! - */ - -int flash_erase(flash_info_t *info, int s_first, int s_last) -{ - vu_long *addr = (vu_long *) (info->start[0]); - int flag, prot, sect, l_sect, in_mid, in_did; - ulong start, now, last; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) - printf("- missing\n"); - else - printf("- no sectors to erase\n"); - - return 1; - } - - if ((info->flash_id == FLASH_UNKNOWN) || - (info->flash_id > FLASH_AMD_COMP)) { - printf("Can't erase unknown flash type %08lx - aborted\n", - info->flash_id); - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; ++sect) { - if (info->protect[sect]) - prot++; - } - - if (prot) { - printf("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf("\n"); - } - - l_sect = -1; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - -#if defined(CONFIG_BOOT_8B) - my_out_8((unsigned char *)((ulong)addr + 0x555), 0xaa); - my_out_8((unsigned char *)((ulong)addr + 0x2aa), 0x55); - my_out_8((unsigned char *)((ulong)addr + 0x555), 0x90); - - in_mid = my_in_8((unsigned char *)addr); - in_did = my_in_8((unsigned char *)((ulong)addr + 1)); - - printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did); - - my_out_8((unsigned char *)addr, 0xf0); - udelay(1); - - my_out_8((unsigned char *)((ulong)addr + 0x555), 0xaa); - my_out_8((unsigned char *)((ulong)addr + 0x2aa), 0x55); - my_out_8((unsigned char *)((ulong)addr + 0x555), 0x80); - my_out_8((unsigned char *)((ulong)addr + 0x555), 0xaa); - my_out_8((unsigned char *)((ulong)addr + 0x2aa), 0x55); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr = (vu_long *) (info->start[sect]); - /*addr[0] = 0x00300030; */ - my_out_8((unsigned char *)((ulong)addr), 0x30); - l_sect = sect; - } - } -#elif defined(CONFIG_BOOT_16B) - my_out_be16((unsigned short *)((ulong)addr + (0xaaa)), 0xaa); - my_out_be16((unsigned short *)((ulong)addr + (0x554)), 0x55); - my_out_be16((unsigned short *)((ulong)addr + (0xaaa)), 0x90); - in_mid = my_in_be16((unsigned short *)addr); - in_did = my_in_be16((unsigned short *)((ulong)addr + 2)); - printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did); - my_out_be16((unsigned short *)addr, 0xf0); - udelay(1); - my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xaa); - my_out_be16((unsigned short *)((ulong)addr + 0x554), 0x55); - my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0x80); - my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xaa); - my_out_be16((unsigned short *)((ulong)addr + 0x554), 0x55); - /* Start erase on unprotected sectors */ - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr = (vu_long *) (info->start[sect]); - my_out_be16((unsigned short *)((ulong)addr), 0x30); - l_sect = sect; - } - } - -#elif defined(CONFIG_BOOT_32B) - my_out_be32((unsigned *)((ulong)addr + 0x1554), 0xaa); - my_out_be32((unsigned *)((ulong)addr + 0xaa8), 0x55); - my_out_be32((unsigned *)((ulong)addr + 0x1554), 0x90); - - in_mid = my_in_be32((unsigned *)addr); - in_did = my_in_be32((unsigned *)((ulong)addr + 4)); - - printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did); - - my_out_be32((unsigned *) addr, 0xf0); - udelay(1); - - my_out_be32((unsigned *)((ulong)addr + 0x1554), 0xaa); - my_out_be32((unsigned *)((ulong)addr + 0xaa8), 0x55); - my_out_be32((unsigned *)((ulong)addr + 0x1554), 0x80); - my_out_be32((unsigned *)((ulong)addr + 0x1554), 0xaa); - my_out_be32((unsigned *)((ulong)addr + 0xaa8), 0x55); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr = (vu_long *) (info->start[sect]); - my_out_be32((unsigned *)((ulong)addr), 0x00300030); - l_sect = sect; - } - } - -#else -#error CONFIG_BOOT_(size)B missing. -#endif - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* wait at least 80us - let's wait 1 ms */ - udelay(1000); - - /* - * We wait for the last triggered sector - */ - if (l_sect < 0) - goto DONE; - - start = get_timer(0); - last = start; - addr = (vu_long *) (info->start[l_sect]); -#if defined(CONFIG_BOOT_8B) - while ((my_in_8((unsigned char *) addr) & 0x80) != 0x80) -#elif defined(CONFIG_BOOT_16B) - while ((my_in_be16((unsigned short *) addr) & 0x0080) != 0x0080) -#elif defined(CONFIG_BOOT_32B) - while ((my_in_be32((unsigned *) addr) & 0x00800080) != 0x00800080) -#else -#error CONFIG_BOOT_(size)B missing. -#endif - { - now = get_timer(start); - if (now > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf("Timeout\n"); - return 1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - putc('.'); - last = now; - } - } -DONE: - /* reset to read mode */ - addr = (volatile unsigned long *) info->start[0]; - -#if defined(CONFIG_BOOT_8B) - my_out_8((unsigned char *) addr, 0xf0); -#elif defined(CONFIG_BOOT_16B) - my_out_be16((unsigned short *) addr, 0x00f0); -#elif defined(CONFIG_BOOT_32B) - my_out_be32((unsigned *) addr, 0x00F000F0); /* reset bank */ -#else -#error CONFIG_BOOT_(size)B missing. -#endif - printf(" done\n"); - return 0; -} - -/* - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ - -int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt) -{ - ulong cp, wp, data; - int i, l, rc; - - wp = (addr & ~3); /* get lower word aligned address */ - - /* - * handle unaligned start bytes - */ - l = addr - wp; - - if (l != 0) { - data = 0; - for (i = 0, cp = wp; i < l; ++i, ++cp) - data = (data << 8) | (*(uchar *) cp); - - for (; i < 4 && cnt > 0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt == 0 && i < 4; ++i, ++cp) - data = (data << 8) | (*(uchar *) cp); - - rc = write_word(info, wp, data); - - if (rc != 0) - return rc; - - wp += 4; - } - - /* - * handle word aligned part - */ - while (cnt >= 4) { - data = 0; - for (i = 0; i < 4; ++i) - data = (data << 8) | *src++; - - rc = write_word(info, wp, data); - - if (rc != 0) - return rc; - - wp += 4; - cnt -= 4; - } - - if (cnt == 0) - return 0; - - /* - * handle unaligned tail bytes - */ - data = 0; - for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i < 4; ++i, ++cp) - data = (data << 8) | (*(uchar *) cp); - - return write_word(info, wp, data); -} - -/* - * Write a word to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_word(flash_info_t *info, ulong dest, ulong data) -{ - ulong addr = (ulong) (info->start[0]); - ulong start; - int flag; - ulong i; - int data_short[2]; - - /* Check if Flash is (sufficiently) erased */ - if (((ulong)*(ulong *)dest & data) != data) - return 2; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); -#if defined(CONFIG_BOOT_8B) -#ifdef DEBUG - { - int in_mid, in_did; - - my_out_8((unsigned char *) (addr + 0x555), 0xaa); - my_out_8((unsigned char *) (addr + 0x2aa), 0x55); - my_out_8((unsigned char *) (addr + 0x555), 0x90); - - in_mid = my_in_8((unsigned char *) addr); - in_did = my_in_8((unsigned char *) (addr + 1)); - - printf(" man ID=0x%x, dev ID=0x%x.\n", in_mid, in_did); - - my_out_8((unsigned char *) addr, 0xf0); - udelay(1); - } -#endif - { - int data_ch[4]; - - data_ch[0] = (int) ((data >> 24) & 0xff); - data_ch[1] = (int) ((data >> 16) & 0xff); - data_ch[2] = (int) ((data >> 8) & 0xff); - data_ch[3] = (int) (data & 0xff); - - for (i = 0; i < 4; i++) { - my_out_8((unsigned char *) (addr + 0x555), 0xaa); - my_out_8((unsigned char *) (addr + 0x2aa), 0x55); - my_out_8((unsigned char *) (addr + 0x555), 0xa0); - my_out_8((unsigned char *) (dest + i), data_ch[i]); - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - start = get_timer(0); - while ((my_in_8((unsigned char *)(dest + i))) != - (data_ch[i])) { - if (get_timer(start) > - CONFIG_SYS_FLASH_WRITE_TOUT) { - return 1; - } - } - } /* for */ - } -#elif defined(CONFIG_BOOT_16B) - data_short[0] = (int) (data >> 16) & 0xffff; - data_short[1] = (int) data & 0xffff; - for (i = 0; i < 2; i++) { - my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xaa); - my_out_be16((unsigned short *)((ulong)addr + 0x554), 0x55); - my_out_be16((unsigned short *)((ulong)addr + 0xaaa), 0xa0); - my_out_be16((unsigned short *)(dest + (i * 2)), - data_short[i]); - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - start = get_timer(0); - while ((my_in_be16((unsigned short *)(dest + (i * 2)))) != - (data_short[i])) { - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) - return 1; - } - } -#elif defined(CONFIG_BOOT_32B) - addr[0x0555] = 0x00AA00AA; - addr[0x02AA] = 0x00550055; - addr[0x0555] = 0x00A000A0; - - *((vu_long *)dest) = data; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* data polling for D7 */ - start = get_timer(0); - while ((*((vu_long *)dest) & 0x00800080) != (data & 0x00800080)) { - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) - return 1; - } -#endif - return 0; -} - -#ifdef CONFIG_BOOT_8B -static int my_in_8(unsigned char *addr) -{ - int ret; - __asm__ __volatile__("lbz%U1%X1 %0,%1; eieio":"=r"(ret):"m"(*addr)); - - return ret; -} - -static void my_out_8(unsigned char *addr, int val) -{ - __asm__ __volatile__("stb%U0%X0 %1,%0; eieio":"=m"(*addr):"r"(val)); -} -#endif -#ifdef CONFIG_BOOT_16B -static int my_in_be16(unsigned short *addr) -{ - int ret; - __asm__ __volatile__("lhz%U1%X1 %0,%1; eieio":"=r"(ret):"m"(*addr)); - - return ret; -} - -static void my_out_be16(unsigned short *addr, int val) -{ - __asm__ __volatile__("sth%U0%X0 %1,%0; eieio":"=m"(*addr):"r"(val)); -} -#endif -#ifdef CONFIG_BOOT_32B -static unsigned my_in_be32(unsigned *addr) -{ - unsigned ret; - __asm__ __volatile__("lwz%U1%X1 %0,%1; eieio":"=r"(ret):"m"(*addr)); - - return ret; -} - -static void my_out_be32(unsigned *addr, int val) -{ - __asm__ __volatile__("stw%U0%X0 %1,%0; eieio":"=m"(*addr):"r"(val)); -} -#endif diff --git a/board/svm_sc8xx/svm_sc8xx.c b/board/svm_sc8xx/svm_sc8xx.c deleted file mode 100644 index 5db48506c6..0000000000 --- a/board/svm_sc8xx/svm_sc8xx.c +++ /dev/null @@ -1,144 +0,0 @@ -/* - * (C) Copyright 2000, 2001, 2002 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -/* ------------------------------------------------------------------------- */ -const uint sdram_table[] = -{ -/*----------------- - UPM A contents: ------------------ */ -/*--------------------------------------------------- - Read Single Beat Cycle. Offset 0 in the RAM array. ----------------------------------------------------- */ -0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00 , -0x1ff77c47, 0x1ff77c35, 0xefeabc34, 0x1fb57c35 , -/*------------------------------------------------ - Read Burst Cycle. Offset 0x8 in the RAM array. ------------------------------------------------- */ -0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00, -0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47, -0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, -0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, -/*------------------------------------------------------- - Write Single Beat Cycle. Offset 0x18 in the RAM array -------------------------------------------------------- */ -0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47 , -0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff , -/*------------------------------------------------- - Write Burst Cycle. Offset 0x20 in the RAM array -------------------------------------------------- */ -0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00, -0xf0affc00, 0xe1bbbc04, 0x1ff77c47, 0xffffffff, -0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff , -0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff , -/*------------------------------------------------------------------------ - Periodic Timer Expired. For DRAM refresh. Offset 0x30 in the RAM array ------------------------------------------------------------------------- */ -0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04, -0xfffffc84, 0xfffffc07, 0xffffffff, 0xffffffff, -0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff , -/*----------- -* Exception: -* ----------- */ -0x7ffefc07, 0xffffffff, 0xffffffff, 0xffffffff , -}; - -/* ------------------------------------------------------------------------- */ -/* - * Check Board Identity: - * - * Test ID string (SVM8...) - * - * Return 1 for "SC8xx" type, 0 else. - */ - -int checkboard(void) -{ - char buf[64]; - int i; - int l = getenv_f("serial#", buf, sizeof(buf)); - - if (l < 0 || strncmp(buf, "SVM8", 4)) { - printf("### No HW ID - assuming SVM SC8xx\n"); - return (0); - } - - for (i = 0; i < l; ++i) { - if (buf[i] == ' ') - break; - putc(buf[i]); - } - - putc('\n'); - - return 0; -} - -/* ------------------------------------------------------------------------- */ - -phys_size_t initdram (int board_type) -{ - volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR; - volatile memctl8xx_t *memctl = &immap->im_memctl; - long int size_b0 = 0; - - upmconfig(UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint)); - - memctl->memc_mptpr = CONFIG_SYS_MPTPR; -#if defined (CONFIG_SDRAM_16M) - memctl->memc_mamr = 0x00802114 | CONFIG_SYS_MxMR_PTx; - memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */ - udelay(1); - memctl->memc_mcr = 0x80002830; - udelay(1); - memctl->memc_mar = 0x00000088; - udelay(1); - memctl->memc_mcr = 0x80002106; - udelay(1); - memctl->memc_or1 = 0xff000a00; - size_b0 = 0x01000000; -#elif defined (CONFIG_SDRAM_32M) - memctl->memc_mamr = 0x00904114 | CONFIG_SYS_MxMR_PTx; - memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */ - udelay(1); - memctl->memc_mcr = 0x80002830; - udelay(1); - memctl->memc_mar = 0x00000088; - udelay(1); - memctl->memc_mcr = 0x80002106; - udelay(1); - memctl->memc_or1 = 0xfe000a00; - size_b0 = 0x02000000; -#elif defined (CONFIG_SDRAM_64M) - memctl->memc_mamr = 0x00a04114 | CONFIG_SYS_MxMR_PTx; - memctl->memc_mcr = 0x80002105; /* SDRAM bank 0 */ - udelay(1); - memctl->memc_mcr = 0x80002830; - udelay(1); - memctl->memc_mar = 0x00000088; - udelay(1); - memctl->memc_mcr = 0x80002106; - udelay(1); - memctl->memc_or1 = 0xfc000a00; - size_b0 = 0x04000000; -#else -#error SDRAM size configuration missing. -#endif - memctl->memc_br1 = 0x00000081; - udelay(200); - return (size_b0 ); -} - -#if defined(CONFIG_CMD_DOC) -void doc_init (void) -{ - doc_probe (CONFIG_SYS_DOC_BASE); -} -#endif diff --git a/board/svm_sc8xx/u-boot.lds b/board/svm_sc8xx/u-boot.lds deleted file mode 100644 index df564e9395..0000000000 --- a/board/svm_sc8xx/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000-2010 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc) - -SECTIONS -{ - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .text : - { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - arch/powerpc/cpu/mpc8xx/start.o (.text*) - arch/powerpc/cpu/mpc8xx/traps.o (.text*) - lib/built-in.o (.text*) - net/built-in.o (.text*) - arch/powerpc/cpu/mpc8xx/built-in.o (.text*) - arch/powerpc/lib/built-in.o (.text*) - board/svm_sc8xx/built-in.o (.text*) - *(.text.*printf) - *(.text.do_mem_*) - *(.text.flash*) - *(.text.run_command) - *(.text.main_loop) - *(.text.srec_decode) - - . = env_offset; - common/env_embedded.o (.ppcenv*) - - *(.text*) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - _GOT2_TABLE_ = .; - KEEP(*(.got2)) - KEEP(*(.got)) - PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4); - _FIXUP_TABLE_ = .; - KEEP(*(.fixup)) - } - __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data*) - *(.sdata*) - } - _edata = .; - PROVIDE (edata = .); - - - . = .; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss (NOLOAD) : - { - *(.bss*) - *(.sbss*) - *(COMMON) - . = ALIGN(4); - } - __bss_end = . ; - PROVIDE (end = .); -} diff --git a/board/svm_sc8xx/u-boot.lds.debug b/board/svm_sc8xx/u-boot.lds.debug deleted file mode 100644 index b2c562c33d..0000000000 --- a/board/svm_sc8xx/u-boot.lds.debug +++ /dev/null @@ -1,114 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc) -/* Do we need any of these for elf? - __DYNAMIC = 0; */ -SECTIONS -{ - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - - arch/powerpc/cpu/mpc8xx/start.o (.text) - common/dlmalloc.o (.text) - lib/vsprintf.o (.text) - lib/crc32.o (.text) - - . = env_offset; - common/env_embedded.o(.text) - - *(.text) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.rodata) - *(.rodata1) - *(.rodata.str1.4) - *(.eh_frame) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x0FFF) & 0xFFFFF000; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2; - __fixup_entries = (. - _FIXUP_TABLE_)>>2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(4096); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(4096); - __init_end = .; - - __bss_start = .; - .bss : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - } - __bss_end = . ; - PROVIDE (end = .); -} diff --git a/configs/svm_sc8xx_defconfig b/configs/svm_sc8xx_defconfig deleted file mode 100644 index 9f0d343a82..0000000000 --- a/configs/svm_sc8xx_defconfig +++ /dev/null @@ -1,3 +0,0 @@ -CONFIG_PPC=y -CONFIG_8xx=y -CONFIG_TARGET_SVM_SC8XX=y diff --git a/doc/README.scrapyard b/doc/README.scrapyard index b7b16d1e6b..55b2c23a6f 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order. Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= +svm_sc8xx powerpc mpc8xx - - John Zhan stxxtc powerpc mpc8xx - - Dan Malek omap5912osk arm arm926ejs - - Rishi Bhattacharya p1023rds powerpc mpc85xx d0bc5140 2014-07-22 Roy Zang diff --git a/drivers/pcmcia/tqm8xx_pcmcia.c b/drivers/pcmcia/tqm8xx_pcmcia.c index dda7d37445..8b7447853b 100644 --- a/drivers/pcmcia/tqm8xx_pcmcia.c +++ b/drivers/pcmcia/tqm8xx_pcmcia.c @@ -20,14 +20,12 @@ #endif #if defined(CONFIG_PCMCIA) \ - && (defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx)) + && defined(CONFIG_TQM8xxL) #if defined(CONFIG_VIRTLAB2) #define PCMCIA_BOARD_MSG "Virtlab2" #elif defined(CONFIG_TQM8xxL) #define PCMCIA_BOARD_MSG "TQM8xxL" -#elif defined(CONFIG_SVM_SC8xx) -#define PCMCIA_BOARD_MSG "SC8xx" #endif #if defined(CONFIG_NSCU) @@ -302,4 +300,4 @@ done: return 0; } -#endif /* CONFIG_PCMCIA && (CONFIG_TQM8xxL || CONFIG_SVM_SC8xx) */ +#endif /* CONFIG_PCMCIA && CONFIG_TQM8xxL */ diff --git a/include/commproc.h b/include/commproc.h index 52ac4caf5a..fec818d13a 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -779,57 +779,6 @@ typedef struct scc_enet { /*** NETVIA *******************************************************/ -/* SinoVee Microsystems SC8xx series FEL8xx-AT,SC823,SC850,SC855T,SC860T */ -#if ( defined CONFIG_SVM_SC8xx ) -# ifndef CONFIG_FEC_ENET - -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 - - /* Bits in parallel I/O port registers that have to be set/cleared - * * * * to configure the pins for SCC2 use. - * * * */ -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0400) /* PA 5 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ - -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ - -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ -/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to - * * * * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero. - * * * */ -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00003700) - -# else /* Use FEC for Fast Ethernet */ - -#undef SCC_ENET -#define FEC_ENET - -#define PD_MII_TXD1 ((ushort)0x1000) /* PD 3 */ -#define PD_MII_TXD2 ((ushort)0x0800) /* PD 4 */ -#define PD_MII_TXD3 ((ushort)0x0400) /* PD 5 */ -#define PD_MII_RX_DV ((ushort)0x0200) /* PD 6 */ -#define PD_MII_RX_ERR ((ushort)0x0100) /* PD 7 */ -#define PD_MII_RX_CLK ((ushort)0x0080) /* PD 8 */ -#define PD_MII_TXD0 ((ushort)0x0040) /* PD 9 */ -#define PD_MII_RXD0 ((ushort)0x0020) /* PD 10 */ -#define PD_MII_TX_ERR ((ushort)0x0010) /* PD 11 */ -#define PD_MII_MDC ((ushort)0x0008) /* PD 12 */ -#define PD_MII_RXD1 ((ushort)0x0004) /* PD 13 */ -#define PD_MII_RXD2 ((ushort)0x0002) /* PD 14 */ -#define PD_MII_RXD3 ((ushort)0x0001) /* PD 15 */ - -#define PD_MII_MASK ((ushort)0x1FFF) /* PD 3...15 */ - -# endif /* CONFIG_FEC_ENET */ -#endif /* CONFIG_SVM_SC8xx */ - - #if defined(CONFIG_NETVIA) /* Bits in parallel I/O port registers that have to be set/cleared * to configure the pins for SCC2 use. diff --git a/include/configs/svm_sc8xx.h b/include/configs/svm_sc8xx.h deleted file mode 100644 index b4aa948565..0000000000 --- a/include/configs/svm_sc8xx.h +++ /dev/null @@ -1,450 +0,0 @@ -/* - * (C) Copyright 2000, 2001, 2002 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific, - * for SinoVee Microsystems SC8xx series SBC - * http://www.fel.com.cn (Chinese) - * http://www.sinovee.com (English) - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_TEXT_BASE 0x40000000 - -/* Custom configuration */ -/* SC823,SC850,SC860SAR, FEL8xx-AT(823/850/860) */ -/* SC85T,SC860T, FEL8xx-AT(855T/860T) */ -/*#define CONFIG_FEL8xx_AT */ -/*#define CONFIG_LCD */ -/*#define CONFIG_MPC8XX_LCD*/ -/* if core > 50MHz , un-comment CONFIG_BUS_DIV2 */ -/* #define CONFIG_50MHz */ -/* #define CONFIG_66MHz */ -/* #define CONFIG_75MHz */ -#define CONFIG_80MHz -/*#define CONFIG_100MHz */ -/* #define CONFIG_BUS_DIV2 1 */ -/* for BOOT device port size */ -/* #define CONFIG_BOOT_8B */ -#define CONFIG_BOOT_16B -/* #define CONFIG_BOOT_32B */ -/* #define CONFIG_CAN_DRIVER */ -/* #define DEBUG */ -#define CONFIG_FEC_ENET - -/* #define CONFIG_SDRAM_16M */ -#define CONFIG_SDRAM_32M -/* #define CONFIG_SDRAM_64M */ -#define CONFIG_SYS_RESET_ADDRESS 0xffffffff -/* - * High Level Configuration Options - * (easy to change) - */ - -/* #define CONFIG_MPC823 1 */ -/* #define CONFIG_MPC850 1 */ -#define CONFIG_MPC855 1 -/* #define CONFIG_MPC860 1 */ -/* #define CONFIG_MPC860T 1 */ - -#undef CONFIG_WATCHDOG /* watchdog */ - -#define CONFIG_SVM_SC8xx 1 /* ...on SVM SC8xx series */ - -#ifdef CONFIG_LCD /* with LCD controller ? */ -/* #define CONFIG_NEC_NL6448BC20 1 / * use NEC NL6448BC20 display */ -#endif - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 19200 /* console baudrate = 115kbps */ -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#define CONFIG_BOARD_TYPES 1 /* support board types */ - -#define CONFIG_PREBOOT "echo;echo Welcome to U-Boot SVM port;echo;echo Type \"? or help\" to get on-line help;echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 0x210000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/sinovee/ppc8xx-linux-2.0/target\0" \ - "bootfile=pImage-sc855t\0" \ - "kernel_addr=48000000\0" \ - "ramdisk_addr=48100000\0" \ - "" -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \ - "tftpboot 0x210000 pImage-sc855t;bootm 0x210000" - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ - - -#ifdef CONFIG_LCD -# undef CONFIG_STATUS_LED /* disturbs display */ -#else -# define CONFIG_STATUS_LED 1 /* Status LED enabled */ -#endif /* CONFIG_LCD */ - -#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DATE - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#ifdef CONFIG_SYS_HUSH_PARSER -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x40000000 -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 - -#ifdef CONFIG_BOOT_8B -#define CONFIG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ -#elif defined (CONFIG_BOOT_16B) -#define CONFIG_ENV_OFFSET 0x10000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ -#elif defined (CONFIG_BOOT_32B) -#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ -#endif - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - - -/*----------------------------------------------------------------------- - * Hardware Information Block - */ -#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */ -#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */ -#define CONFIG_SYS_HWINFO_MAGIC 0x46454C38 /* 'SVM8' */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -/*#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -*/ -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR 0xffffff88 -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#ifndef CONFIG_CAN_DRIVER -/*#define CONFIG_SYS_SIUMCR 0x00610c00 */ -#define CONFIG_SYS_SIUMCR 0x00000000 -#else /* we must activate GPL5 in the SIUMCR for CAN */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01) -#endif /* CONFIG_CAN_DRIVER */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR 0x0001 - -/*----------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RTCSC 0x00c3 - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR 0x0000 - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer - * interrupt status bit - */ -#if defined (CONFIG_100MHz) -#define CONFIG_SYS_PLPRCR 0x06301000 -#define CONFIG_8xx_GCLK_FREQ 100000000 -#elif defined (CONFIG_80MHz) -#define CONFIG_SYS_PLPRCR 0x04f01000 -#define CONFIG_8xx_GCLK_FREQ 80000000 -#elif defined(CONFIG_75MHz) -#define CONFIG_SYS_PLPRCR 0x04a00100 -#define CONFIG_8xx_GCLK_FREQ 75000000 -#elif defined(CONFIG_66MHz) -#define CONFIG_SYS_PLPRCR 0x04101000 -#define CONFIG_8xx_GCLK_FREQ 66000000 -#elif defined(CONFIG_50MHz) -#define CONFIG_SYS_PLPRCR 0x03101000 -#define CONFIG_8xx_GCLK_FREQ 50000000 -#endif - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#ifdef CONFIG_BUS_DIV2 -#define CONFIG_SYS_SCCR 0x02020000 | SCCR_RTSEL -#else /* up to 50 MHz we use a 1:1 clock */ -#define CONFIG_SYS_SCCR 0x02000000 | SCCR_RTSEL -#endif - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) - -/*----------------------------------------------------------------------- - * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ -#define CONFIG_IDE_INIT_POSTRESET 1 /* Use postreset IDE hook */ -#define CONFIG_IDE_8xx_DIRECT 1 /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_BASE_ADDR 0xFE100010 -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -/*#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0C00 */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O - */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0200 /* Offset for normal register accesses - */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0210 /* Offset for alternate registers - */ -#define CONFIG_ATAPI -#define CONFIG_SYS_PIO_MODE 0 - -/*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -/*#define CONFIG_SYS_DER 0x2002000F*/ -#define CONFIG_SYS_DER 0x0 - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */ - -/* used to re-map FLASH both when starting from SRAM or FLASH: - * restrict access enough to keep SRAM working (if any) - * but not too much to meddle with FLASH accesses - */ -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ - -/* - * FLASH timing: - */ -#if defined(CONFIG_100MHz) -#define CONFIG_SYS_OR_TIMING_FLASH 0x000002f4 -#define CONFIG_SYS_OR_TIMING_DOC 0x000002f4 -#define CONFIG_SYS_MxMR_PTx 0x61000000 -#define CONFIG_SYS_MPTPR 0x400 - -#elif defined(CONFIG_80MHz) -#define CONFIG_SYS_OR_TIMING_FLASH 0x00000ff4 -#define CONFIG_SYS_OR_TIMING_DOC 0x000001f4 -#define CONFIG_SYS_MxMR_PTx 0x4e000000 -#define CONFIG_SYS_MPTPR 0x400 - -#elif defined(CONFIG_75MHz) -#define CONFIG_SYS_OR_TIMING_FLASH 0x000008f4 -#define CONFIG_SYS_OR_TIMING_DOC 0x000002f4 -#define CONFIG_SYS_MxMR_PTx 0x49000000 -#define CONFIG_SYS_MPTPR 0x400 - -#elif defined(CONFIG_66MHz) -#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \ - OR_SCY_3_CLK | OR_EHTR | OR_BI) -/*#define CONFIG_SYS_OR_TIMING_FLASH 0x000001f4 */ -#define CONFIG_SYS_OR_TIMING_DOC 0x000003f4 -#define CONFIG_SYS_MxMR_PTx 0x40000000 -#define CONFIG_SYS_MPTPR 0x400 - -#else /* 50 MHz */ -#define CONFIG_SYS_OR_TIMING_FLASH 0x00000ff4 -#define CONFIG_SYS_OR_TIMING_DOC 0x000001f4 -#define CONFIG_SYS_MxMR_PTx 0x30000000 -#define CONFIG_SYS_MPTPR 0x400 -#endif /*CONFIG_??MHz */ - - -#if defined (CONFIG_BOOT_8B) /* 512K X 8 ,29F040 , 2MB space */ -#define CONFIG_SYS_OR0_PRELIM (0xffe00000 | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_8) -#elif defined (CONFIG_BOOT_16B) /* 29lv160 X 16 , 4MB space */ -#define CONFIG_SYS_OR0_PRELIM (0xffc00000 | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16) -#elif defined( CONFIG_BOOT_32B ) /* 29lv160 X 2 X 32, 4/8/16MB , 64MB space */ -#define CONFIG_SYS_OR0_PRELIM (0xfc000000 | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) -#else -#error Boot device port size missing. -#endif - -/* - * Disk-On-Chip configuration - */ - -#define CONFIG_SYS_DOC_SHORT_TIMEOUT -#define CONFIG_SYS_MAX_DOC_DEVICE 1 /* Max number of DOC devices */ - -#define CONFIG_SYS_DOC_SUPPORT_2000 -#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM -#define CONFIG_SYS_DOC_BASE 0x80000000 - -#endif /* __CONFIG_H */ diff --git a/include/pcmcia.h b/include/pcmcia.h index 8aec2541b8..4b667f49ce 100644 --- a/include/pcmcia.h +++ b/include/pcmcia.h @@ -21,7 +21,7 @@ #if !defined(CONFIG_PCMCIA_SLOT_A) && !defined(CONFIG_PCMCIA_SLOT_B) -#if defined(CONFIG_TQM8xxL) || defined(CONFIG_SVM_SC8xx) +#if defined(CONFIG_TQM8xxL) # define CONFIG_PCMCIA_SLOT_B /* The TQM8xxL use SLOT_B */ #elif defined(CONFIG_SPD823TS) /* The SPD8xx use SLOT_B */ # define CONFIG_PCMCIA_SLOT_B diff --git a/include/status_led.h b/include/status_led.h index a41d3bc96d..c9d21d105f 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -217,20 +217,6 @@ void status_led_set (int led, int state); # define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ -#elif defined(CONFIG_SVM_SC8xx) -# define STATUS_LED_PAR im_cpm.cp_pbpar -# define STATUS_LED_DIR im_cpm.cp_pbdir -# define STATUS_LED_ODR im_cpm.cp_pbodr -# define STATUS_LED_DAT im_cpm.cp_pbdat - -# define STATUS_LED_BIT 0x00000001 -# define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -# define STATUS_LED_STATE STATUS_LED_BLINKING - -# define STATUS_LED_ACTIVE 1 /* LED on for bit == 1 */ - -# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - #elif defined(CONFIG_V38B) # define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */ -- 2.25.1