From cb40adff8fd5335c0f623562c57bf8505c32b16f Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Fri, 25 Aug 2017 13:02:53 +0200 Subject: [PATCH] pfla02: Fix RAM detection and support 1 bank SOM In case of 2 banks, the address space of the first CS must be defined and not let to the higher value. Add support for SOM with a single bank of RAM. It was tested with i.MX6Q modules in the following configurations: - 2 Banks, 4 GB - 2 Banks, 1 GB - 1 Bank, 1 GB Signed-off-by: Stefano Babic --- board/phytec/pfla02/Kconfig | 6 +++ board/phytec/pfla02/pfla02.c | 87 ++++++++++++++++++++++-------------- 2 files changed, 60 insertions(+), 33 deletions(-) diff --git a/board/phytec/pfla02/Kconfig b/board/phytec/pfla02/Kconfig index 142a1222fc..f4da68b5ba 100644 --- a/board/phytec/pfla02/Kconfig +++ b/board/phytec/pfla02/Kconfig @@ -9,4 +9,10 @@ config SYS_VENDOR config SYS_CONFIG_NAME default "pfla02" +config SPL_DRAM_1_BANK + bool "DRAM on just one bank" + help + activate, if the module has just one bank + of RAM + endif diff --git a/board/phytec/pfla02/pfla02.c b/board/phytec/pfla02/pfla02.c index ec9264d45c..136f1d5e70 100644 --- a/board/phytec/pfla02/pfla02.c +++ b/board/phytec/pfla02/pfla02.c @@ -485,9 +485,9 @@ static const struct mx6_mmdc_calibration mx6_mmcd_calib = { /* Index in RAM Chip array */ enum { - RAM_1GB, - RAM_2GB, - RAM_4GB + RAM_MT64K, + RAM_MT128K, + RAM_MT256K }; static struct mx6_ddr3_cfg mt41k_xx[] = { @@ -550,31 +550,11 @@ static void ccgr_init(void) writel(0x000003FF, &ccm->CCGR6); } -static void spl_dram_init(struct mx6_ddr3_cfg *mem_ddr) +static void spl_dram_init(struct mx6_ddr_sysinfo *sysinfo, + struct mx6_ddr3_cfg *mem_ddr) { - struct mx6_ddr_sysinfo sysinfo = { - /* width of data bus:0=16,1=32,2=64 */ - .dsize = 2, - /* config for full 4GB range so that get_mem_size() works */ - .cs_density = 32, /* 32Gb per CS */ - /* single chip select */ - .ncs = 2, - .cs1_mirror = 0, - .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */ - .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */ - .walat = 1, /* Write additional latency */ - .ralat = 5, /* Read additional latency */ - .mif3_mode = 3, /* Command prediction working mode */ - .bi_on = 1, /* Bank interleaving enabled */ - .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ - .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ - .ddr_type = DDR_TYPE_DDR3, - .refsel = 1, /* Refresh cycles at 32KHz */ - .refr = 7, /* 8 refresh commands per refresh cycle */ - }; - mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs); - mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, mem_ddr); + mx6_dram_cfg(sysinfo, &mx6_mmcd_calib, mem_ddr); } int board_mmc_init(bd_t *bis) @@ -616,10 +596,12 @@ void board_boot_order(u32 *spl_boot_list) * Function checks for mirrors in the first CS */ #define RAM_TEST_PATTERN 0xaa5555aa -static unsigned int pfla02_detect_ramsize(void) +#define MIN_BANK_SIZE (512 * 1024 * 1024) + +static unsigned int pfla02_detect_chiptype(void) { u32 *p, *p1; - unsigned int offset = 512 * 1024 * 1024; + unsigned int offset = MIN_BANK_SIZE; int i; for (i = 0; i < 2; i++) { @@ -638,12 +620,38 @@ static unsigned int pfla02_detect_ramsize(void) if (*p == *p1) return i; } - return RAM_4GB; + return RAM_MT256K; } void board_init_f(ulong dummy) { unsigned int ramchip; + + struct mx6_ddr_sysinfo sysinfo = { + /* width of data bus:0=16,1=32,2=64 */ + .dsize = 2, + /* config for full 4GB range so that get_mem_size() works */ + .cs_density = 32, /* 512 MB */ + /* single chip select */ +#if IS_ENABLED(CONFIG_SPL_DRAM_1_BANK) + .ncs = 1, +#else + .ncs = 2, +#endif + .cs1_mirror = 1, + .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */ + .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */ + .walat = 1, /* Write additional latency */ + .ralat = 5, /* Read additional latency */ + .mif3_mode = 3, /* Command prediction working mode */ + .bi_on = 1, /* Bank interleaving enabled */ + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ + .ddr_type = DDR_TYPE_DDR3, + .refsel = 1, /* Refresh cycles at 32KHz */ + .refr = 7, /* 8 refresh commands per refresh cycle */ + }; + #ifdef CONFIG_CMD_NAND /* Enable NAND */ setup_gpmi_nand(); @@ -671,10 +679,23 @@ void board_init_f(ulong dummy) setup_gpios(); /* DDR initialization */ - spl_dram_init(&mt41k_xx[RAM_4GB]); - ramchip = pfla02_detect_ramsize(); - if (ramchip != RAM_4GB) - spl_dram_init(&mt41k_xx[ramchip]); + spl_dram_init(&sysinfo, &mt41k_xx[RAM_MT256K]); + ramchip = pfla02_detect_chiptype(); + debug("Detected chip %d\n", ramchip); +#if !IS_ENABLED(CONFIG_SPL_DRAM_1_BANK) + switch (ramchip) { + case RAM_MT64K: + sysinfo.cs_density = 6; + break; + case RAM_MT128K: + sysinfo.cs_density = 10; + break; + case RAM_MT256K: + sysinfo.cs_density = 18; + break; + } +#endif + spl_dram_init(&sysinfo, &mt41k_xx[ramchip]); /* Clear the BSS. */ memset(__bss_start, 0, __bss_end - __bss_start); -- 2.25.1