From bb0dc1084f5dcf1dfd951d320c932d08bccbe429 Mon Sep 17 00:00:00 2001 From: Ying Zhang Date: Fri, 16 Aug 2013 15:16:11 +0800 Subject: [PATCH] powerpc: mpc85xx: Support booting from SD Card with SPL The code from the internal on-chip ROM. It loads the final uboot image into DDR, then jump to it to begin execution. The SPL's size is sizeable, the maximum size must not exceed the size of L2 SRAM. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are two stage uboot images: * spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 96KB. * final uboot image, size is variable depends on the functions enabled. Signed-off-by: Ying Zhang Acked-by: York Sun --- README | 4 + arch/powerpc/cpu/mpc85xx/u-boot-spl.lds | 5 + .../cpu/mpc8xxx/ddr/lc_common_dimm_params.c | 4 + doc/README.mpc85xx-sd-spi-boot | 81 +++++++++++ drivers/mmc/Makefile | 3 + drivers/mmc/fsl_esdhc_spl.c | 130 ++++++++++++++++++ drivers/mmc/mmc.c | 2 + include/fsl_esdhc.h | 1 + spl/Makefile | 3 + 9 files changed, 233 insertions(+) create mode 100644 doc/README.mpc85xx-sd-spi-boot create mode 100644 drivers/mmc/fsl_esdhc_spl.c diff --git a/README b/README index 953ff17900..301d1a95cd 100644 --- a/README +++ b/README @@ -3090,6 +3090,10 @@ FIT uImage format: Support for NAND boot using simple NAND drivers that expose the cmd_ctrl() interface. + CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT + Set for the SPL on PPC mpc8xxx targets, support for + arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary. + CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT, CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE, CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS, diff --git a/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds b/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds index 08188d75e5..85ec74ba94 100644 --- a/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds +++ b/arch/powerpc/cpu/mpc85xx/u-boot-spl.lds @@ -44,6 +44,11 @@ SECTIONS } _edata = .; + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + . = ALIGN(8); __init_begin = .; __init_end = .; diff --git a/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c b/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c index e958e138dd..56128a7b96 100644 --- a/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c +++ b/arch/powerpc/cpu/mpc8xxx/ddr/lc_common_dimm_params.c @@ -218,12 +218,16 @@ compute_lowest_common_dimm_parameters(const dimm_params_t *dimm_params, if (dimm_params[i].n_ranks) { if (dimm_params[i].registered_dimm) { temp1 = 1; +#ifndef CONFIG_SPL_BUILD printf("Detected RDIMM %s\n", dimm_params[i].mpart); +#endif } else { temp2 = 1; +#ifndef CONFIG_SPL_BUILD printf("Detected UDIMM %s\n", dimm_params[i].mpart); +#endif } } } diff --git a/doc/README.mpc85xx-sd-spi-boot b/doc/README.mpc85xx-sd-spi-boot new file mode 100644 index 0000000000..d5043ccb66 --- /dev/null +++ b/doc/README.mpc85xx-sd-spi-boot @@ -0,0 +1,81 @@ +---------------------------------------- +Booting from On-Chip ROM (eSDHC or eSPI) +---------------------------------------- + +boot_format is a tool to write SD bootable images to a filesystem and build +SD/SPI images to a binary file for writing later. + +When booting from an SD card/MMC, boot_format puts the configuration file and +the RAM-based U-Boot image on the card. +When booting from an EEPROM, boot_format generates a binary image that is used +to boot from this EEPROM. + +Where to get boot_format: +======================== + +you can browse it online at: +http://git.freescale.com/git/cgit.cgi/ppc/sdk/boot-format.git/ + +Building +======== + +Run the following to build this project + + $ make + +Execution +========= + +boot_format runs under a regular Linux machine and requires a super user mode +to run. Execute boot_format as follows. + +For building SD images by writing directly to a file system on SD media: + + $ boot_format $config u-boot.bin -sd $device + +Where $config is the included config.dat file for your platform and $device +is the target block device for the SD media on your computer. + +For build binary images directly a local file: + + $ boot_format $config u-boot.bin -spi $file + +Where $file is the target file. Also keep in mind the u-boot.bin file needs +to be the u-boot built for your particular platform and target media. + +Example: To generate a u-boot.bin for a P1022DS booting from SD, run the +following in the u-boot repository: + + $ make P1022DS_SDCARD + +Configuration Files +=================== + +Below are the configuration files to be used with a particular platform. Keep +in mind that some of these config files are tied to the platforms DDR speed. +Please see the SoC reference manual for more documentation. + +P1022DS config_sram_p1022ds.dat +P2020DS config_sram_p2020ds.dat +P2010DS config_sram_p2020ds.dat +P1020RDB config_ddr2_1g_p1020rdb_533M.dat +P1020RDB config_ddr2_1g_p1020rdb_667M.dat +P2020RDB config_ddr2_1g_p2020rdb_800M.dat +P2020RDB config_ddr2_1g_p2020rdb_667M.dat +P2020RDB config_ddr3_1gb_64bit_p2020rdb_pc.dat +P2010RDB config_ddr3_1gb_64bit_p2020rdb_pc.dat +P1020RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat +P1011RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat +P1010RDB config_ddr3_1gb_p1010rdb_800M.dat +P1014RDB config_ddr3_1gb_p1014rdb_800M.dat +P1021RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat +P1012RDB config_ddr3_1gb_p1_p2_rdb_pc_800M.dat +P1022DS config_ddr3_2gb_p1022ds.dat +P1013DS config_ddr3_2gb_p1022ds.dat +P1024RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat +P1013RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat +P1025RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat +P1016RDB config_ddr3_1gb_p1_p2_rdb_pc_667M.dat +P1020UTM config_ddr3_1gb_p1_p2_rdb_pc_800M.dat +P1020MBG config_ddr3_1gb_p1_p2_rdb_pc_800M.dat +MPC8536DS config_ddr2_512m_mpc8536ds_667M.dat diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile index 49e5cb9c2a..bedf833f70 100644 --- a/drivers/mmc/Makefile +++ b/drivers/mmc/Makefile @@ -32,6 +32,9 @@ COBJS-$(CONFIG_TEGRA_MMC) += tegra_mmc.o COBJS-$(CONFIG_DWMMC) += dw_mmc.o COBJS-$(CONFIG_EXYNOS_DWMMC) += exynos_dw_mmc.o COBJS-$(CONFIG_ZYNQ_SDHCI) += zynq_sdhci.o +ifdef CONFIG_SPL_BUILD +COBJS-$(CONFIG_SPL_MMC_BOOT) += fsl_esdhc_spl.o +endif COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c) diff --git a/drivers/mmc/fsl_esdhc_spl.c b/drivers/mmc/fsl_esdhc_spl.c new file mode 100644 index 0000000000..25a1dff1b0 --- /dev/null +++ b/drivers/mmc/fsl_esdhc_spl.c @@ -0,0 +1,130 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include +#include +#include + +/* + * The environment variables are written to just after the u-boot image + * on SDCard, so we must read the MBR to get the start address and code + * length of the u-boot image, then calculate the address of the env. + */ +#define ESDHC_BOOT_IMAGE_SIZE 0x48 +#define ESDHC_BOOT_IMAGE_ADDR 0x50 +#define MBRDBR_BOOT_SIG_55 0x1fe +#define MBRDBR_BOOT_SIG_AA 0x1ff +#define CONFIG_CFG_DATA_SECTOR 0 + +/* + * The main entry for mmc booting. It's necessary that SDRAM is already + * configured and available since this code loads the main U-Boot image + * from mmc into SDRAM and starts it from there. + */ + +void __noreturn mmc_boot(void) +{ + __attribute__((noreturn)) void (*uboot)(void); + uint blk_start, blk_cnt, err; + u32 blklen; + uchar *tmp_buf; + uchar val; + uint i, byte_num; + u32 offset, code_len; + struct mmc *mmc; + + mmc = find_mmc_device(0); + if (!mmc) { + puts("spl: mmc device not found!!\n"); + hang(); + } + + blklen = mmc->read_bl_len; + tmp_buf = malloc(blklen); + if (!tmp_buf) { + puts("spl: malloc memory failed!!\n"); + hang(); + } + memset(tmp_buf, 0, blklen); + + /* + * Read source addr from sd card + */ + err = mmc->block_dev.block_read(0, CONFIG_CFG_DATA_SECTOR, 1, tmp_buf); + if (err != 1) { + puts("spl: mmc read failed!!\n"); + free(tmp_buf); + hang(); + } + + val = *(tmp_buf + MBRDBR_BOOT_SIG_55); + if (0x55 != val) { + puts("spl: mmc signature is not valid!!\n"); + free(tmp_buf); + hang(); + } + val = *(tmp_buf + MBRDBR_BOOT_SIG_AA); + if (0xAA != val) { + puts("spl: mmc signature is not valid!!\n"); + free(tmp_buf); + hang(); + } + + byte_num = 4; + offset = 0; + for (i = 0; i < byte_num; i++) { + val = *(tmp_buf + ESDHC_BOOT_IMAGE_ADDR + i); + offset = (offset << 8) + val; + } + offset += CONFIG_SYS_MMC_U_BOOT_OFFS; + /* Get the code size from offset 0x48 */ + byte_num = 4; + code_len = 0; + for (i = 0; i < byte_num; i++) { + val = *(tmp_buf + ESDHC_BOOT_IMAGE_SIZE + i); + code_len = (code_len << 8) + val; + } + code_len -= CONFIG_SYS_MMC_U_BOOT_OFFS; + /* + * Load U-Boot image from mmc into RAM + */ + blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len; + blk_cnt = ALIGN(code_len, mmc->read_bl_len) / mmc->read_bl_len; + err = mmc->block_dev.block_read(0, blk_start, blk_cnt, + (uchar *)CONFIG_SYS_MMC_U_BOOT_DST); + if (err != blk_cnt) { + puts("spl: mmc read failed!!\n"); + free(tmp_buf); + hang(); + } + + /* + * Clean d-cache and invalidate i-cache, to + * make sure that no stale data is executed. + */ + flush_cache(CONFIG_SYS_MMC_U_BOOT_DST, CONFIG_SYS_MMC_U_BOOT_SIZE); + + /* + * Jump to U-Boot image + */ + uboot = (void *)CONFIG_SYS_MMC_U_BOOT_START; + (*uboot)(); +} diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c index 4da8db9bed..55026759ed 100644 --- a/drivers/mmc/mmc.c +++ b/drivers/mmc/mmc.c @@ -1483,7 +1483,9 @@ int mmc_initialize(bd_t *bis) if (board_mmc_init(bis) < 0) cpu_mmc_init(bis); +#ifndef CONFIG_SPL_BUILD print_mmc_devices(','); +#endif do_preinit(); return 0; diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h index 2c97398f4e..89bcbd1700 100644 --- a/include/fsl_esdhc.h +++ b/include/fsl_esdhc.h @@ -182,5 +182,6 @@ void fdt_fixup_esdhc(void *blob, bd_t *bd); static inline int fsl_esdhc_mmc_init(bd_t *bis) { return -ENOSYS; } static inline void fdt_fixup_esdhc(void *blob, bd_t *bd) {} #endif /* CONFIG_FSL_ESDHC */ +void __noreturn mmc_boot(void); #endif /* __FSL_ESDHC_H__ */ diff --git a/spl/Makefile b/spl/Makefile index 02f4860755..a9a8564f62 100644 --- a/spl/Makefile +++ b/spl/Makefile @@ -50,6 +50,9 @@ LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o endif ifeq ($(CPU),mpc85xx) LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o +ifdef CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +LIBS-y += arch/powerpc/cpu/mpc8xxx/ddr/libddr.o +endif endif ifeq ($(CPU),mpc86xx) LIBS-y += arch/powerpc/cpu/mpc8xxx/lib8xxx.o -- 2.25.1