From a9f524904730a0f722483938bf7eb8baedbc2448 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 4 Dec 2013 09:27:34 +0100 Subject: [PATCH] arm: omap3: Add SPL support to tao3530 Add SPL support for the Technexion TAO3530 SOM to replace x-loader. Tested with the Thunder baseboard. Currently this is only tested with the TAO3530 SOM revision (Ax/Bx). Tested by booting via MMC and NAND. Signed-off-by: Stefan Roese Cc: Tapani Utriainen Cc: Thorsten Eisbein Cc: Tom Rini --- board/technexion/tao3530/tao3530.c | 27 ++++++++++++- include/configs/tao3530.h | 65 ++++++++++++++++++++++++++++++ 2 files changed, 91 insertions(+), 1 deletion(-) diff --git a/board/technexion/tao3530/tao3530.c b/board/technexion/tao3530/tao3530.c index 0668c256f3..9268d38877 100644 --- a/board/technexion/tao3530/tao3530.c +++ b/board/technexion/tao3530/tao3530.c @@ -67,6 +67,31 @@ out: return ret; } +#ifdef CONFIG_SPL_BUILD +/* + * Routine: get_board_mem_timings + * Description: If we use SPL then there is no x-loader nor config header + * so we have to setup the DDR timings ourself on both banks. + */ +void get_board_mem_timings(struct board_sdrc_timings *timings) +{ + if (tao3530_revision() < 3) { + /* 256MB / Bank */ + timings->mcfg = MCFG(256 << 20, 14); /* RAS-width 14 */ + timings->ctrla = HYNIX_V_ACTIMA_165; + timings->ctrlb = HYNIX_V_ACTIMB_165; + } else { + /* 128MB / Bank */ + timings->mcfg = MCFG(128 << 20, 13); /* RAS-width 13 */ + timings->ctrla = MICRON_V_ACTIMA_165; + timings->ctrlb = MICRON_V_ACTIMB_165; + } + + timings->mr = MICRON_V_MR_165; + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; +} +#endif + /* * Routine: board_init * Description: Early hardware init. @@ -134,7 +159,7 @@ void set_muxconf_regs(void) MUX_TAO3530(); } -#ifdef CONFIG_GENERIC_MMC +#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD) int board_mmc_init(bd_t *bis) { omap_mmc_init(0, 0, 0, -1, -1); diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h index cf20ae78f0..fdc6c066da 100644 --- a/include/configs/tao3530.h +++ b/include/configs/tao3530.h @@ -5,6 +5,8 @@ * Edward Lin * Tapani Utriainen * + * Copyright (C) 2013 Stefan Roese + * * SPDX-License-Identifier: GPL-2.0+ */ @@ -298,4 +300,67 @@ #define CONFIG_USB_STORAGE #define CONGIG_CMD_STORAGE +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_NAND_SIMPLE + +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" + +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_OMAP3_ID_NAND +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" + +/* NAND boot config */ +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +/* + * Use the ECC/OOB layout from omap_gpmc.h that matches your chip: + * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT + */ +#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13 } +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define CONFIG_SPL_TEXT_BASE 0x40200800 +#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK + +/* + * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the + * older x-loader implementations. And move the BSS area so that it + * doesn't overlap with TEXT_BASE. + */ +#define CONFIG_SYS_TEXT_BASE 0x80008000 +#define CONFIG_SPL_BSS_START_ADDR 0x80100000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 + #endif /* __CONFIG_H */ -- 2.25.1