From a30abb1b6bb66d1caf08c331805163e6fef6f2a1 Mon Sep 17 00:00:00 2001 From: DENG Qingfang Date: Tue, 14 Jan 2020 22:22:59 +0800 Subject: [PATCH] ipq40xx: add support for MobiPromo CM520-79F MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019 Specification: SoC/Wireless: QCA IPQ4019 RAM: 512MiB Flash: 128MiB SLC NAND Ethernet PHY: QCA8075 Ethernet ports: 1x WAN, 2x LAN LEDs: 7 LEDs 2 (USB, CAN) are GPIO other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register Button: Reset Flash instruction: Disassemble the router, connect UART pins like this: GND TX RX [x x . . x .] [. . . . . .] (QCA8075 and IPQ4019 below) Baud-rate: 115200 Set up TFTP server: IP 192.168.1.188/24 Power on the router and interrupt the booting with UART console env backup (in case you want to go back to stock and need it there): printenv (Copy the output to somewhere save) Set bootenv: setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs' setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1' setenv cm520_boot 'run set_ubi; run bootkernel' setenv bootcmd 'run cm520_boot' setenv bootargs saveenv Boot initramfs from TFTP: tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb bootm After initramfs image is booted, backup rootfs partition in case of reverting to stock image cat /dev/mtd12 > /tmp/mtd12.bin Then fetch it via SCP Upload nand-factory.ubi to /tmp via SCP, then run mtd erase rootfs mtd write /tmp/*nand-factory.ubi rootfs reboot To revert to stock image, restore default bootenv in uboot UART console setenv bootcmd 'bootipq' printenv use the saved dump you did back when you installed OpenWrt to verify that there are no other differences from back in the day. saveenv upload the backed up mtd12.bin and run tftpboot mtd12.bin nand erase 0xb80000 0x7480000 nand write 0x84000000 0xb80000 0x7480000 The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead In case of this, set it back to rootfs: cd /tmp cat /dev/mtd7 > mtd7.bin echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4 for i in 28 48 68 108; do dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i done mtd write mtd7.bin BOOTCONFIG mtd write mtd7.bin BOOTCONFIG1 Signed-off-by: DENG Qingfang [renamed volume to ubi to support autoboot, as per David Lam's test in PR#2432] Signed-off-by: Christian Lamparter --- package/firmware/ipq-wifi/Makefile | 2 + .../board-mobipromo_cm520-79f.qca4019 | Bin 0 -> 24308 bytes .../ipq40xx/base-files/etc/board.d/01_leds | 5 + .../ipq40xx/base-files/etc/board.d/02_network | 5 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 2 + .../base-files/lib/upgrade/platform.sh | 1 + .../arm/boot/dts/qcom-ipq4019-cm520-79f.dts | 354 ++++++++++++++++++ .../arm/boot/dts/qcom-ipq4019-cm520-79f.dts | 354 ++++++++++++++++++ target/linux/ipq40xx/image/Makefile | 12 + .../901-arm-boot-add-dts-files.patch | 3 +- .../901-arm-boot-add-dts-files.patch | 3 +- 11 files changed, 739 insertions(+), 2 deletions(-) create mode 100644 package/firmware/ipq-wifi/board-mobipromo_cm520-79f.qca4019 create mode 100644 target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts create mode 100644 target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 12e000bac8..f767d49294 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -33,6 +33,7 @@ ALLWIFIBOARDS:= \ engenius_emd1 \ ezviz_cs-w3-wd1200g-eup \ linksys_ea8300 \ + mobipromo_cm520-79f \ qxwlan_e2600ac ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) @@ -102,6 +103,7 @@ $(eval $(call generate-ipq-wifi-package,engenius_eap2200,EnGenius EAP2200)) $(eval $(call generate-ipq-wifi-package,engenius_emd1,EnGenius EMD1)) $(eval $(call generate-ipq-wifi-package,ezviz_cs-w3-wd1200g-eup,EZVIZ CS-W3-WD1200G EUP)) $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) +$(eval $(call generate-ipq-wifi-package,mobipromo_cm520-79f,MobiPromo CM520-79F)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac,Qxwlan E2600AC)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) diff --git a/package/firmware/ipq-wifi/board-mobipromo_cm520-79f.qca4019 b/package/firmware/ipq-wifi/board-mobipromo_cm520-79f.qca4019 new file mode 100644 index 0000000000000000000000000000000000000000..d717af12fe24a0060af79dc5b0fe7993114a1c86 GIT binary patch literal 24308 zcmeHPdr(tX8b1jj>e9ju0TJ*LLVyHAfPfk#%2OI3f<;9FECN*|sZkz=hoK90d{Bsp zKrI*|Xc?48Q$)ta2gG7+?ToVf$NsUif3%%_bZ6FG+tKc{GrNm>?hSz?B$`N=2Do21 z=X~e8=R4;+znmoZ-t*(Wofsb)zef-eo)(&r5ucd^q*5t>QWA#c0BnJ&NLI0}u%w7x zBo&9gQz9-66(86Zj@OEg7M35ts@!mPWnsCv@W`=ki90uO!$Y@3Cre4tmj?Txg$YVX zB;Zg-iORzI4C#Sc0RU^A-Jk*h6@WJ*am{qbV$rd#0Emo?{PEc{5}&#X{QQ@5vAW~{ zJ9tgGXYALa9SOXE0*}qqW?Ji={d{J3Bc!Ip_%hg zU~rai+GJaKU9yz3-y>mspsX|b471#;pmQ*{Gx`jz!o9Gsu}~IW6tsIo%H5VDwL8S@ zT#xNv^w)fpafVZ|;ho!qRh>JVLaTg>N6(g2Z$HS&LZa`$c1aRWuKV_@ec}#5Bwimg8!pa}r%hM7f9vWM^ll)9HS2 zgr9zT_WkrUb_T>_1qNts|NZ_?-|5@1h8tX*$&QZygY8`58#d?v{Q1)-+O~@rF5Y$N z5Ii4&T4`PL5SB0_M_)pi3& z$q$;_I_4{YKO=XoQYa{eLwQ6&yisqCx6loBL%h%gG=Y=wC;>@DQ#q-^I5Z9spj?#8 z;XdLbThXnYt-^3L9O0p}L8z{nR%c`4^Jk+X)OqiZC6KtI?oZtjAJm8ABTPgSpC%${ zXc{L?7>PzcjYMM57*32(`zGk;_)uEt7d^+8ZRrQ9A^jA%K+*eYF{v7TR2EcS4(FuA z94uJ^1WE)-W)L8jh8bWC%qtQl0|bZ)fdGL3fdGL3fdGNP3PxZZcOBwKd5ilNl0n(R z-GanYR_g?07PVd(xv!t=F8!@5=Z~>QCpH^n1;2&F)U8C|`8=_*gT-oY$XYNzilyz$ z_h6Stgn1>3(Z>M5vRctI`q;SSgtFOec&D3&+NTDC3khKc!T9V{gW=7@XP25?E=s+i z;s65Nzhl({5CMW9KgSQUff$eqMTZG1TPP8LPWSbt8%aB~&$rU)d2I~9=aImVM*(Pe zMo4i{05Df0fDibN1*;H1_8_m#gQc4rzUinJ385}G1YQigP|4&2a0deJE|VQse+1<+ z6x}?>pe)2D%!XgCJ)>WlD}#dq8NX!G?%Zkj>a@Fa!d-i^^9l}>C|cS(x_WxA4GoWu zjeqvwtH;(K(A&qe?#y+`v)+88uts@+ zSY^gFj@m>0J@uXk&2yJ$z31>;lxEr+oByem&yDSd^{%d|sjeOu7egwHVH;~|D{>o` zn6xEJ#12uiBy8KXK^g$q4ZomeUSx3f4Nhl7)|Z9*V=ArK%CSaAr<@#RhN?f>(Szkd78H-ChvXgT;8-~PqF{{H7D zPyPmN=J@t}epI-YuRlHg?;mW>!8gUX4-4aPu!QY1V0X;v_>RNEHTFjQ20R_^5ZFXB zwZI6zz4q$z?%YM@3REq*ccRa<*XlTATC^5D$JVYs*B;XsNVg9ZW@9(G#~&MBVa(M` zeO~l!Uyo?oRh9BAQP|hFG)h&iJYU4q+*DnVmx+>jftnF@uR<;n@qDrW5xaXYmxA`zwY*qYy}TIEtv0*{6{j86s!1H73;o+Zzkx~=X~ z$RxW(ThzA|7bN9^Bpw$!w8;MN>7=$x*;qv(`W3It3a&6w&#JS0CXq2U9J`v(7S`Y+8yPNErJmpT z8=s@+da{}$j?*Nr>0k68ZjGxCl&;TL4Dapco%gGyNE-U{ySS%O8Kr3KTG@rT_gUqX zz4r&iZL#$MhrRM^2lrkIZSbyqvv6Rz>f^X(X6?EXg);qA#4(S3Z|u0$U(~v_j`prc z?&r7U0~yNT6P{A_b=j4eMtUV>e`9CH>8MICk&EEQ;QkMJ@B2wT^83`{?xb@x8B)+c zSfS#dqL;aeM!UmNSUlibQUPA%>jIC3erF{qkac(qg9 zuw52%$UUv^+R=+KCj-i<`4{^OJL8-DD=7Kxed3G!(*YIkd1ssVy%!~+=ThQE1}eJJ z&oZmL4zAdRLrk1NU>P8=(5G*}XJE~V2|R`y3V3e#(>DSG8SoE2d4m?Gl&Gzc&kD;U6ud&$}Cg3Mb1Og@zm`AsNZq&?DvWKnP8HKUZs;}hRy$dGs2EZ@1eCE-)~HZ*S{gN$dLiKO*im(f|Me literal 0 HcmV?d00001 diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index dd7f35a0a3..0a128e8cbc 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -43,6 +43,11 @@ engenius,ens620ext) ucidef_set_led_netdev "lan1" "LAN1" "${boardname}:green:lan1" "eth0" ucidef_set_led_netdev "lan2" "LAN2" "${boardname}:green:lan2" "eth1" ;; +mobipromo,cm520-79f) + ucidef_set_led_netdev "wan" "WAN" "${boardname}:blue:wan" "eth1" + ucidef_set_led_switch "lan1" "LAN1" "${boardname}:blue:lan1" "switch0" "0x10" + ucidef_set_led_switch "lan2" "LAN2" "${boardname}:blue:lan2" "switch0" "0x08" + ;; netgear,ex6100v2 |\ netgear,ex6150v2) ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 44cb9f9d12..13e2722f79 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -73,6 +73,11 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" ;; + mobipromo,cm520-79f) + ucidef_add_switch "switch0" \ + "0u@eth0" "3:lan:2" "4:lan:1" + ucidef_set_interface_wan "eth1" + ;; qxwlan,e2600ac-c1 |\ qxwlan,e2600ac-c2) ucidef_set_interfaces_lan_wan "eth0" "eth1" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index c65fa30474..dd301b1e30 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -51,6 +51,7 @@ case "$FIRMWARE" in ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ linksys,ea6350v3 |\ + mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) caldata_extract "ART" 0x1000 0x2f20 ;; @@ -132,6 +133,7 @@ case "$FIRMWARE" in ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ linksys,ea6350v3 |\ + mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) caldata_extract "ART" 0x5000 0x2f20 ;; diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 377f65ea42..7aabeeeea0 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -54,6 +54,7 @@ platform_do_upgrade() { avm,fritzrepeater-3000 |\ cilab,meshpoint-one |\ engenius,eap2200 |\ + mobipromo,cm520-79f |\ qxwlan,e2600ac-c2) nand_do_upgrade "$1" ;; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts new file mode 100644 index 0000000000..f4c1685f47 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts @@ -0,0 +1,354 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "MobiPromo CM520-79F"; + compatible = "mobipromo,cm520-79f"; + + aliases { + led-boot = &led_sys; + led-failsafe = &led_sys; + led-running = &led_sys; + led-upgrade = &led_sys; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>; + reset-delay-us = <1000>; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + ranges; + + sck-gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>; + num-chipselects = <0>; + + led_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <1>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + usb { + label = "cm520-79f:blue:usb"; + gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "usbport"; + trigger-sources = <&usb3_port1>, <&usb3_port2>, <&usb2_port1>; + }; + + led_sys: can { + label = "cm520-79f:blue:can"; + gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; + }; + + wan { + label = "cm520-79f:blue:wan"; + gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>; + }; + + lan1 { + label = "cm520-79f:blue:lan1"; + gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>; + }; + + lan2 { + label = "cm520-79f:blue:lan2"; + gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "cm520-79f:blue:wlan2g"; + gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "cm520-79f:blue:wlan5g"; + gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + status = "okay"; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + mtd-mac-address = <&art 0x1006>; +}; + +&gmac1 { + mtd-mac-address = <&art 0x5006>; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "MIBIB"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "BOOTCONFIG"; + reg = <0x200000 0x100000>; + }; + + partition@300000 { + label = "QSEE"; + reg = <0x300000 0x100000>; + read-only; + }; + + partition@400000 { + label = "QSEE_1"; + reg = <0x400000 0x100000>; + read-only; + }; + + partition@500000 { + label = "CDT"; + reg = <0x500000 0x80000>; + read-only; + }; + + partition@580000 { + label = "CDT_1"; + reg = <0x580000 0x80000>; + read-only; + }; + + partition@600000 { + label = "BOOTCONFIG1"; + reg = <0x600000 0x80000>; + }; + + partition@680000 { + label = "APPSBLENV"; + reg = <0x680000 0x80000>; + }; + + partition@700000 { + label = "APPSBL"; + reg = <0x700000 0x200000>; + read-only; + }; + + partition@900000 { + label = "APPSBL_1"; + reg = <0x900000 0x200000>; + read-only; + }; + + art: partition@b00000 { + label = "ART"; + reg = <0xb00000 0x80000>; + read-only; + }; + + partition@b80000 { + label = "ubi"; + reg = <0xb80000 0x7480000>; + }; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio52", "gpio53", "gpio58", + "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "CM520-79F"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "CM520-79F"; +}; diff --git a/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts new file mode 100644 index 0000000000..f4c1685f47 --- /dev/null +++ b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-cm520-79f.dts @@ -0,0 +1,354 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "MobiPromo CM520-79F"; + compatible = "mobipromo,cm520-79f"; + + aliases { + led-boot = &led_sys; + led-failsafe = &led_sys; + led-running = &led_sys; + led-upgrade = &led_sys; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>; + reset-delay-us = <1000>; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + ranges; + + sck-gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>; + num-chipselects = <0>; + + led_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <1>; + spi-max-frequency = <1000000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + usb { + label = "cm520-79f:blue:usb"; + gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "usbport"; + trigger-sources = <&usb3_port1>, <&usb3_port2>, <&usb2_port1>; + }; + + led_sys: can { + label = "cm520-79f:blue:can"; + gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; + }; + + wan { + label = "cm520-79f:blue:wan"; + gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>; + }; + + lan1 { + label = "cm520-79f:blue:lan1"; + gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>; + }; + + lan2 { + label = "cm520-79f:blue:lan2"; + gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "cm520-79f:blue:wlan2g"; + gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "cm520-79f:blue:wlan5g"; + gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + status = "okay"; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + mtd-mac-address = <&art 0x1006>; +}; + +&gmac1 { + mtd-mac-address = <&art 0x5006>; +}; + +&nand { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "MIBIB"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "BOOTCONFIG"; + reg = <0x200000 0x100000>; + }; + + partition@300000 { + label = "QSEE"; + reg = <0x300000 0x100000>; + read-only; + }; + + partition@400000 { + label = "QSEE_1"; + reg = <0x400000 0x100000>; + read-only; + }; + + partition@500000 { + label = "CDT"; + reg = <0x500000 0x80000>; + read-only; + }; + + partition@580000 { + label = "CDT_1"; + reg = <0x580000 0x80000>; + read-only; + }; + + partition@600000 { + label = "BOOTCONFIG1"; + reg = <0x600000 0x80000>; + }; + + partition@680000 { + label = "APPSBLENV"; + reg = <0x680000 0x80000>; + }; + + partition@700000 { + label = "APPSBL"; + reg = <0x700000 0x200000>; + read-only; + }; + + partition@900000 { + label = "APPSBL_1"; + reg = <0x900000 0x200000>; + read-only; + }; + + art: partition@b00000 { + label = "ART"; + reg = <0xb00000 0x80000>; + read-only; + }; + + partition@b80000 { + label = "ubi"; + reg = <0xb80000 0x7480000>; + }; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio52", "gpio53", "gpio58", + "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", + "gpio57", "gpio60", "gpio61", + "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", + "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "CM520-79F"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "CM520-79F"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 4bbdda5d8a..c47eec51a0 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -452,6 +452,18 @@ define Device/meraki_mr33 endef TARGET_DEVICES += meraki_mr33 +define Device/mobipromo_cm520-79f + $(call Device/FitzImage) + $(call Device/UbiFit) + DEVICE_VENDOR := MobiPromo + DEVICE_MODEL := CM520-79F + SOC := qcom-ipq4019 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_PACKAGES := ipq-wifi-mobipromo_cm520-79f kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += mobipromo_cm520-79f + define Device/netgear_ex61x0v2 $(call Device/DniImage) DEVICE_DTS_CONFIG := config@4 diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 81e33b15a9..24965cf264 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,44 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,45 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -36,6 +36,7 @@ Signed-off-by: John Crispin qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ + qcom-ipq4019-a62.dtb \ ++ qcom-ipq4019-cm520-79f.dtb \ + qcom-ipq4019-eap2200.dtb \ + qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-fritzrepeater-1200.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index a63f0da85d..a17314240f 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,44 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,45 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -36,6 +36,7 @@ Signed-off-by: John Crispin qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ + qcom-ipq4019-a62.dtb \ ++ qcom-ipq4019-cm520-79f.dtb \ + qcom-ipq4019-ea8300.dtb \ + qcom-ipq4019-eap2200.dtb \ + qcom-ipq4019-fritzbox-7530.dtb \ -- 2.25.1