From 8d8d3540eb544fa29167d74029f92a99b9a31eea Mon Sep 17 00:00:00 2001 From: Ian Ray Date: Thu, 31 Jan 2019 16:21:14 +0200 Subject: [PATCH] board: ge: bx50v3: Enable CONFIG_DM_SPI, CONFIG_DM_SPI_FLASH Use SPI flash device model, and remove SPI pin configuration code since the pinctrl driver is used. Signed-off-by: Ian Ray --- arch/arm/dts/imx6q-bx50v3.dts | 27 +++++++++++++++++++++++++++ board/ge/bx50v3/bx50v3.c | 25 ------------------------- configs/ge_bx50v3_defconfig | 2 ++ 3 files changed, 29 insertions(+), 25 deletions(-) diff --git a/arch/arm/dts/imx6q-bx50v3.dts b/arch/arm/dts/imx6q-bx50v3.dts index 0fff2195f9..deaec63509 100644 --- a/arch/arm/dts/imx6q-bx50v3.dts +++ b/arch/arm/dts/imx6q-bx50v3.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "imx6q.dtsi" +#include / { model = "General Electric Bx50v3"; @@ -17,6 +18,16 @@ &iomuxc { pinctrl-names = "default"; + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + /* SPI1 CS */ + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + >; + }; + pinctrl_usdhc3: usdhc3grp { fsl,pins = < MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 @@ -60,3 +71,19 @@ &usdhc4 { status = "disabled"; }; + +/* SPI NOR */ +&ecspi1 { + cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash: n25q032@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c index dac063dc43..b69b9e727b 100644 --- a/board/ge/bx50v3/bx50v3.c +++ b/board/ge/bx50v3/bx50v3.c @@ -53,9 +53,6 @@ static struct vpd_cache vpd; #define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) -#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) - #define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ PAD_CTL_ODE | PAD_CTL_SRE_FAST) @@ -113,13 +110,6 @@ static void setup_iomux_enet(void) mdelay(1); } -static iomux_v3_cfg_t const ecspi1_pads[] = { - MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - static struct i2c_pads_info i2c_pad_info1 = { .scl = { .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD, @@ -159,18 +149,6 @@ static struct i2c_pads_info i2c_pad_info3 = { } }; -#ifdef CONFIG_MXC_SPI -int board_spi_cs_gpio(unsigned bus, unsigned cs) -{ - return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1; -} - -static void setup_spi(void) -{ - imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); -} -#endif - static iomux_v3_cfg_t const pcie_pads[] = { MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), @@ -594,9 +572,6 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; -#ifdef CONFIG_MXC_SPI - setup_spi(); -#endif return 0; } diff --git a/configs/ge_bx50v3_defconfig b/configs/ge_bx50v3_defconfig index 1acda9ec74..14114acbce 100644 --- a/configs/ge_bx50v3_defconfig +++ b/configs/ge_bx50v3_defconfig @@ -59,3 +59,5 @@ CONFIG_BLK=y CONFIG_PINCTRL=y CONFIG_PINCTRL_IMX6=y CONFIG_DM_GPIO=y +CONFIG_DM_SPI=y +CONFIG_DM_SPI_FLASH=y -- 2.25.1