From 877bfe37dc00b0ae59f37742954a62bce3fdf3a0 Mon Sep 17 00:00:00 2001 From: Valentin Longchamp Date: Fri, 18 Oct 2013 11:47:24 +0200 Subject: [PATCH] mpc85xx: introduce the kmp204x reference design support This patch introduces the support for Keymile's kmp204x reference design. This design is based on Freescale's P2040/P2041 SoC. The peripherals used by this design are: - DDR3 RAM with SPD support - SPI NOR Flash as boot medium - NAND Flash - 2 PCIe busses (hosts 1 and 3) - 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5) - 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt FPGA - 2 HW I2C busses - last but not least, the mandatory serial port The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb support and was changed according to our design (that means essentially removing what is not present on the designs and a few adaptations). There is currently only one prototype board that is based on this design and this patch also introduces it. The board is called kmlion1. Signed-off-by: Stefan Bigler Signed-off-by: Valentin Longchamp kmp204x: update the ENV #define The comments had to be refined as well as the total size Signed-off-by: Valentin Longchamp [York Sun: fix ddr.c] Acked-by: York Sun --- board/keymile/kmp204x/Makefile | 48 +++ board/keymile/kmp204x/ddr.c | 64 ++++ board/keymile/kmp204x/eth.c | 71 ++++ board/keymile/kmp204x/kmp204x.c | 258 +++++++++++++++ board/keymile/kmp204x/kmp204x.h | 15 + board/keymile/kmp204x/law.c | 40 +++ board/keymile/kmp204x/pbi.cfg | 35 ++ board/keymile/kmp204x/pci.c | 35 ++ board/keymile/kmp204x/rcw_kmp204x.cfg | 11 + board/keymile/kmp204x/tlb.c | 110 +++++++ boards.cfg | 3 + include/configs/km/kmp204x-common.h | 450 ++++++++++++++++++++++++++ include/configs/kmp204x.h | 68 ++++ 13 files changed, 1208 insertions(+) create mode 100644 board/keymile/kmp204x/Makefile create mode 100644 board/keymile/kmp204x/ddr.c create mode 100644 board/keymile/kmp204x/eth.c create mode 100644 board/keymile/kmp204x/kmp204x.c create mode 100644 board/keymile/kmp204x/kmp204x.h create mode 100644 board/keymile/kmp204x/law.c create mode 100644 board/keymile/kmp204x/pbi.cfg create mode 100644 board/keymile/kmp204x/pci.c create mode 100644 board/keymile/kmp204x/rcw_kmp204x.cfg create mode 100644 board/keymile/kmp204x/tlb.c create mode 100644 include/configs/km/kmp204x-common.h create mode 100644 include/configs/kmp204x.h diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile new file mode 100644 index 0000000000..35d17ce9f5 --- /dev/null +++ b/board/keymile/kmp204x/Makefile @@ -0,0 +1,48 @@ +# +# (C) Copyright 2001-2007 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +ifneq ($(OBJTREE),$(SRCTREE)) +$(shell mkdir -p $(obj)../common) +endif + +LIB = $(obj)lib$(BOARD).o + +COBJS := $(BOARD).o ddr.o eth.o tlb.o pci.o law.o \ + ../common/common.o ../common/ivm.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/keymile/kmp204x/ddr.c b/board/keymile/kmp204x/ddr.c new file mode 100644 index 0000000000..bd425aab1a --- /dev/null +++ b/board/keymile/kmp204x/ddr.c @@ -0,0 +1,64 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * Copyright 2009-2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + if (ctrl_num) { + printf("Wrong parameter for controller number %d", ctrl_num); + return; + } + + /* automatic calibration for nb of cycles between read and DQS pre */ + popts->cpo_override = 0xFF; + + /* 1/2 clk delay between wr command and data strobe */ + popts->write_data_delay = 4; + /* clk lauched 1/2 applied cylcle after address command */ + popts->clk_adjust = 4; + /* 1T timing: command/address held for only 1 cycle */ + popts->twot_en = 0; + + /* we have only one module, half str should be OK */ + popts->half_strength_driver_enable = 1; + + /* wrlvl values overriden as recommended by ddr init func */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x6; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR_ODT_75ohm; +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size = 0; + + puts("Initializing with SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + debug(" DDR: "); + return dram_size; +} diff --git a/board/keymile/kmp204x/eth.c b/board/keymile/kmp204x/eth.c new file mode 100644 index 0000000000..a0731055a2 --- /dev/null +++ b/board/keymile/kmp204x/eth.c @@ -0,0 +1,71 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include + +int board_eth_init(bd_t *bis) +{ + int ret = 0; +#ifdef CONFIG_FMAN_ENET + struct fsl_pq_mdio_info dtsec_mdio_info; + + printf("Initializing Fman\n"); + + dtsec_mdio_info.regs = + (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR; + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the real 1G MDIO bus */ + fsl_pq_mdio_init(bis, &dtsec_mdio_info); + + /* DTESC1/2 don't have a PHY, they are temporarily disabled + * so that u-boot doesn't try to unsuccessfuly enable them */ + fm_disable_port(FM1_DTSEC1); + fm_disable_port(FM1_DTSEC2); + + /* + * Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf + * This is the debug interface, the only one used in u-boot + */ + fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR); + fm_info_set_mdio(FM1_DTSEC5, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + + ret = cpu_eth_init(bis); + + /* reenable DTSEC1/2 for later (kernel) */ + fm_enable_port(FM1_DTSEC1); + fm_enable_port(FM1_DTSEC2); +#endif + + return ret; +} + +#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL) + +#define mv88E1118_PAGE_REG 22 + +int board_phy_config(struct phy_device *phydev) +{ + if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) { + /* driver config is good */ + if (phydev->drv->config) + phydev->drv->config(phydev); + + /* but we still need to fix the LEDs */ + phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003); + phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840); + phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000); + } + + return 0; +} +#endif diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c new file mode 100644 index 0000000000..f02642aece --- /dev/null +++ b/board/keymile/kmp204x/kmp204x.c @@ -0,0 +1,258 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * Copyright 2011,2012 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "../common/common.h" +#include "kmp204x.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + printf("Board: Keymile %s\n", CONFIG_KM_BOARD_NAME); + + return 0; +} + +/* TODO: implement the I2C deblocking function */ +int i2c_make_abort(void) +{ + return 1; +} + +#define ZL30158_RST 8 +#define ZL30343_RST 9 + +int board_early_init_f(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */ + setbits_be32(&gur->ddrclkdr, 0x001f000f); + + /* take the Zarlinks out of reset as soon as possible */ + qrio_prst(ZL30158_RST, false, false); + qrio_prst(ZL30343_RST, false, false); + + /* and set their reset to power-up only */ + qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST); + qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST); + + return 0; +} + +int board_early_init_r(void) +{ + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + set_liodns(); + setup_portals(); + + return 0; +} + +unsigned long get_board_sys_clk(unsigned long dummy) +{ + return 66666666; +} + +#define WDMASK_OFF 0x16 + +static void qrio_wdmask(u8 bit, bool wden) +{ + u16 wdmask; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + wdmask = in_be16(qrio_base + WDMASK_OFF); + + if (wden) + wdmask |= (1 << bit); + else + wdmask &= ~(1 << bit); + + out_be16(qrio_base + WDMASK_OFF, wdmask); +} + +#define PRST_OFF 0x1a + +void qrio_prst(u8 bit, bool en, bool wden) +{ + u16 prst; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + qrio_wdmask(bit, wden); + + prst = in_be16(qrio_base + PRST_OFF); + + if (en) + prst &= ~(1 << bit); + else + prst |= (1 << bit); + + out_be16(qrio_base + PRST_OFF, prst); +} + +#define PRSTCFG_OFF 0x1c + +void qrio_prstcfg(u8 bit, u8 mode) +{ + u32 prstcfg; + u8 i; + void __iomem *qrio_base = (void *)CONFIG_SYS_QRIO_BASE; + + prstcfg = in_be32(qrio_base + PRSTCFG_OFF); + + for (i = 0; i < 2; i++) { + if (mode & (1<bank[i].pllcr0); + actual &= SRDS_PLLCR0_RFCK_SEL_MASK; + if (actual != expected[i]) { + printf("Warning: SERDES bank %u expects reference \ + clock %sMHz, but actual is %sMHz\n", i + 1, + serdes_clock_to_string(expected[i]), + serdes_clock_to_string(actual)); + } + } + + /* take the mgmt eth phy out of reset */ + qrio_prst(PHY_RST, false, false); + + return 0; +} + +#if defined(CONFIG_HUSH_INIT_VAR) +int hush_init_var(void) +{ + ivm_read_eeprom(); + return 0; +} +#endif + +#if defined(CONFIG_LAST_STAGE_INIT) +int last_stage_init(void) +{ + set_km_env(); + return 0; +} +#endif + +#ifdef CONFIG_SYS_DPAA_FMAN +void fdt_fixup_fman_mac_addresses(void *blob) +{ + int node, i, ret; + char *tmp, *end; + unsigned char mac_addr[6]; + + /* get the mac addr from env */ + tmp = getenv("ethaddr"); + if (!tmp) { + printf("ethaddr env variable not defined\n"); + return; + } + for (i = 0; i < 6; i++) { + mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0; + if (tmp) + tmp = (*end) ? end+1 : end; + } + + /* find the correct fdt ethernet path and correct it */ + node = fdt_path_offset(blob, "/soc/fman/ethernet@e8000"); + if (node < 0) { + printf("no /soc/fman/ethernet path offset\n"); + return; + } + ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6); + if (ret) { + printf("error setting local-mac-address property\n"); + return; + } +} +#endif + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB) + fdt_fixup_dr_usb(blob, bd); +#endif + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_fman_mac_addresses(blob); +#endif +} diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h new file mode 100644 index 0000000000..b6ba672413 --- /dev/null +++ b/board/keymile/kmp204x/kmp204x.h @@ -0,0 +1,15 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#define PRSTCFG_POWUP_UNIT_CORE_RST 0x0 +#define PRSTCFG_POWUP_UNIT_RST 0x1 +#define PRSTCFG_POWUP_RST 0x3 + +void qrio_prst(u8 bit, bool en, bool wden); +void qrio_prstcfg(u8 bit, u8 mode); + +void pci_of_setup(void *blob, bd_t *bd); diff --git a/board/keymile/kmp204x/law.c b/board/keymile/kmp204x/law.c new file mode 100644 index 0000000000..75d69e8b48 --- /dev/null +++ b/board/keymile/kmp204x/law.c @@ -0,0 +1,40 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include + +struct law_entry law_table[] = { +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + /* Limit DCSR to 32M to access NPC Trace Buffer */ + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC), +#endif + SET_LAW(CONFIG_SYS_QRIO_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC), +#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS + SET_LAW(CONFIG_SYS_LBAPP1_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +#endif +#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS + SET_LAW(CONFIG_SYS_LBAPP2_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg new file mode 100644 index 0000000000..f38dcf9c8c --- /dev/null +++ b/board/keymile/kmp204x/pbi.cfg @@ -0,0 +1,35 @@ +# +# Copyright 2012 Freescale Semiconductor, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer docs/README.pblimage for more details about how-to configure +# and create PBL boot image +# + +#PBI commands +#Initialize CPC1 as 1MB SRAM +09010000 00200400 +09138000 00000000 +091380c0 00000100 +09010100 00000000 +09010104 fff0000b +09010f00 08000000 +09010000 80000000 +#Configure LAW for CPC1 +09000d00 00000000 +09000d04 fff00000 +09000d08 81000013 +09000010 00000000 +09000014 ff000000 +09000018 81000000 +#Initialize eSPI controller, default configuration is slow for eSPI to +#load data, this configuration comes from u-boot eSPI driver. +09110000 80000403 +09110020 27170008 +09110024 00100008 +09110028 00100008 +0911002c 00100008 +#Flush PBL data +09138000 00000000 +091380c0 00000000 diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c new file mode 100644 index 0000000000..ec20c8afb4 --- /dev/null +++ b/board/keymile/kmp204x/pci.c @@ -0,0 +1,35 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * Copyright 2007-2011 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "kmp204x.h" + +#define PCIE_SW_RST 14 +#define HOOPER_SW_RST 12 + +void pci_init_board(void) +{ + qrio_prst(PCIE_SW_RST, false, false); + qrio_prst(HOOPER_SW_RST, false, false); + /* Hooper is not direcly PCIe capable */ + mdelay(50); + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg new file mode 100644 index 0000000000..f2b7fe3d42 --- /dev/null +++ b/board/keymile/kmp204x/rcw_kmp204x.cfg @@ -0,0 +1,11 @@ +# +# Default RCW for kmp204x boards +# + +#PBL preamble and RCW header +aa55aa55 010e0100 +#64 bytes RCW data +14600000 00000000 28200000 00000000 +148E70CF CFC02000 58000000 41000000 +00000000 00000000 00000000 F4428002 +00000000 00000000 00000000 00000000 diff --git a/board/keymile/kmp204x/tlb.c b/board/keymile/kmp204x/tlb.c new file mode 100644 index 0000000000..d03ca802a4 --- /dev/null +++ b/board/keymile/kmp204x/tlb.c @@ -0,0 +1,110 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * Copyright 2008-2011 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + /* TLB 1 */ + /* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the + * SRAM is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + /* QRIO */ + SET_TLB_ENTRY(1, CONFIG_SYS_QRIO_BASE, CONFIG_SYS_QRIO_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_64K, 1), + /* *I*G* - PCI1 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_512M, 1), + /* *I*G* - PCI3 */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_512M, 1), + /* *I*G* - PCI1&3 I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_128K, 1), +#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS + /* LBAPP1 */ + SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP1_BASE, CONFIG_SYS_LBAPP1_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_256M, 1), +#endif +#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS + /* LBAPP2 */ + SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP2_BASE, CONFIG_SYS_LBAPP2_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_256M, 1), +#endif + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 9, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_1M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 11, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_1M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 13, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 16, BOOKE_PAGESZ_32K, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index 56af10246f..5e101253fc 100644 --- a/boards.cfg +++ b/boards.cfg @@ -43,6 +43,7 @@ # Status, Arch, CPU:SPLCPU, SoC, Vendor, Board name, Target, Options, Maintainers ########################################################################################################### +<<<<<<< HEAD Active arm arm1136 - armltd integrator integratorcp_cm1136 integratorcp:CM1136 Linus Walleij Active arm arm1136 mx31 - - imx31_phycore - - Active arm arm1136 mx31 davedenx - qong - Wolfgang Denk @@ -966,6 +967,7 @@ Active powerpc mpc85xx - gdsys p1022 Active powerpc mpc85xx - gdsys p1022 controlcenterd_36BIT_SDCARD_DEVELOP controlcenterd:36BIT,SDCARD,DEVELOP Dirk Eibach Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER controlcenterd:TRAILBLAZER,SPIFLASH Dirk Eibach Active powerpc mpc85xx - gdsys p1022 controlcenterd_TRAILBLAZER_DEVELOP controlcenterd:TRAILBLAZER,SPIFLASH,DEVELOP Dirk Eibach +Active powerpc mpc85xx - keymile kmp204x kmlion1 kmp204x:KMLION1 Valentin Longchamp Active powerpc mpc85xx - stx stxgp3 stxgp3 - Dan Malek Active powerpc mpc85xx - stx stxssa stxssa stxssa Dan Malek Active powerpc mpc85xx - stx stxssa stxssa_4M stxssa:STXSSA_4M Dan Malek @@ -1221,3 +1223,4 @@ Orphan powerpc mpc8xx - - genietv Orphan powerpc mpc8xx - - mbx8xx MBX - - Orphan powerpc mpc8xx - - mbx8xx MBX860T - - Orphan powerpc mpc8xx - - nx823 NX823 - - + diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h new file mode 100644 index 0000000000..2d5320b5cd --- /dev/null +++ b/include/configs/km/kmp204x-common.h @@ -0,0 +1,450 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_KMP204X_H +#define _CONFIG_KMP204X_H + +#define CONFIG_PHYS_64BIT +#define CONFIG_PPC_P2041 + +#define CONFIG_SYS_TEXT_BASE 0xfff80000 + +#define CONFIG_KM_DEF_NETDEV "netdev=eth0\0" + +#define CONFIG_NAND_ECC_BCH + +/* common KM defines */ +#include "keymile-common.h" + +#define CONFIG_SYS_RAMBOOT +#define CONFIG_RAMBOOT_PBL +#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/keymile/kmp204x/pbi.cfg +#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/keymile/kmp204x/rcw_kmp204x.cfg + +/* High Level Configuration Options */ +#define CONFIG_BOOKE +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_E500MC /* BOOKE e500mc family */ +#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ +#define CONFIG_MPC85xx /* MPC85xx/PQ3 platform */ +#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */ +#define CONFIG_MP /* support multiple processors */ + +#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ +#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ + +#define CONFIG_SYS_DPAA_RMAN /* RMan */ + +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +/* Environment in SPI Flash */ +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 20000000 +#define CONFIG_ENV_SPI_MODE 0 +#define CONFIG_ENV_OFFSET 0x100000 /* 1MB for u-boot */ +#define CONFIG_ENV_SIZE 0x004000 /* 16K env */ +#define CONFIG_ENV_SECT_SIZE 0x010000 +#define CONFIG_ENV_OFFSET_REDUND 0x110000 +#define CONFIG_ENV_TOTAL_SIZE 0x020000 + +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#ifndef __ASSEMBLY__ +unsigned long get_board_sys_clk(unsigned long dummy); +#endif +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_SYS_CACHE_STASHING +#define CONFIG_BACKSIDE_L2_CACHE +#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E +#define CONFIG_BTB /* toggle branch predition */ + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_ADDR_MAP +#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ + +#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00800000 +#define CONFIG_SYS_ALT_MEMTEST +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* + * Config the L3 Cache as L3 SRAM + */ +#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE +#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \ + CONFIG_RAMBOOT_TEXT_BASE) +#define CONFIG_SYS_L3_SIZE (1024 << 10) +#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE) + +#define CONFIG_SYS_DCSRBAR 0xf0000000 +#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull + +/* + * DDR Setup + */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) + +#define CONFIG_DDR_SPD +#define CONFIG_FSL_DDR3 +#define CONFIG_FSL_DDR_INTERACTIVE + +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x54 +#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 + +/****************************************************************************** + * (PRAM usage) + * ... ------------------------------------------------------- + * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM + * ... |<------------------- pram -------------------------->| + * ... ------------------------------------------------------- + * @END_OF_RAM: + * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose + * @CONFIG_KM_PHRAM: address for /var + * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application) + * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM + */ + +/* size of rootfs in RAM */ +#define CONFIG_KM_ROOTFSSIZE 0x0 +/* pseudo-non volatile RAM [hex] */ +#define CONFIG_KM_PNVRAM 0x80000 +/* physical RAM MTD size [hex] */ +#define CONFIG_KM_PHRAM 0x100000 +/* resereved pram area at the end of memroy [hex] */ +#define CONFIG_KM_RESERVED_PRAM 0x0 +/* enable protected RAM */ +#define CONFIG_PRAM 0 + +#define CONFIG_KM_CRAMFS_ADDR 0x2000000 +#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */ +#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */ + +#define CONFIG_BOOTCOUNT_LIMIT + +/* + * Local Bus Definitions + */ + +/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */ +#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2) + +/* Nand Flash */ +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull + +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +#define CONFIG_BCH + +/* NAND flash config */ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | BR_PS_8 /* Port Size = 8 bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ + | OR_FCM_BCTLD /* LBCTL not ass */ \ + | OR_FCM_SCY_1 /* 1 clk wait cycle */ \ + | OR_FCM_RST /* 1 clk read setup */ \ + | OR_FCM_PGS /* Large page size */ \ + | OR_FCM_CST) /* 0.25 command setup */ + +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ + +/* QRIO FPGA */ +#define CONFIG_SYS_QRIO_BASE 0xfb000000 +#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull + +#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \ + | BR_PS_8 /* Port Size 8 bits */ \ + | BR_DECC_OFF /* no error corr */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \ + | OR_GPCM_BCTLD /* no LCTL assert */ \ + | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \ + | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ + | OR_GPCM_TRLX /* relaxed tmgs */ \ + | OR_GPCM_EAD) /* extra bus clk cycles */ + +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */ +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */ + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ +#define CONFIG_MISC_INIT_R +#define CONFIG_LAST_STAGE_INIT + +#define CONFIG_HWCONFIG + +/* define to use L1 as initial stack */ +#define CONFIG_L1_INIT_RAM +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR +/* The assembler doesn't like typecast */ +#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ + ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ + CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) + +/* Serial Port - controlled on board with jumper J8 + * open - index 2 + * shorted - index 1 + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) +#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) +#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) + +#define CONFIG_KM_CONSOLE_TTY "ttyS0" + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_NUM_I2C_BUSES 3 +#define CONFIG_SYS_I2C_MAX_HOPS 1 +#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 +#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \ + {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \ + } + +#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/ + +/* + * eSPI - Enhanced SPI + */ +#define CONFIG_FSL_ESPI +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_BAR /* 4 byte-addressing */ +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 20000000 +#define CONFIG_SF_DEFAULT_MODE 0 + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 1, direct to uli, tgtid 3, Base address 20000 */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +/* controller 3, Slot 1, tgtid 1, Base address 202000 */ +#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* Qman/Bman */ +#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ +#define CONFIG_SYS_BMAN_NUM_PORTALS 10 +#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 +#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull +#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 +#define CONFIG_SYS_QMAN_NUM_PORTALS 10 +#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000 +#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull +#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 + +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_SYS_DPAA_PME +/* Default address of microcode for the Linux Fman driver + * env is stored at 0x100000, sector size is 0x10000, x2 (redundant) + * ucode is stored after env, so we got 0x120000. + */ +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0x120000 +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) + +#define CONFIG_FMAN_ENET +#define CONFIG_PHYLIB_10G +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ + +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_E1000 + +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_DOS_PARTITION + +/* RGMII (FM1@DTESC5) is used as debug itf, it's the only one configured */ +#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11 +#define CONFIG_SYS_TBIPA_VALUE 8 +#define CONFIG_PHYLIB /* recommended PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC5" +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ + +/* + * Environment + */ +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * additionnal command line configuration. + */ +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET + +/* we don't need flash support */ +#define CONFIG_SYS_NO_FLASH +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_FLASH +#undef CONFIG_FLASH_CFI_MTD +#undef CONFIG_JFFS2_CMDLINE + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +#define __USB_PHY_TYPE utmi + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE +#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ +#define CONFIG_KM_DEF_ENV "km-common=empty\0" +#endif + +#ifndef MTDIDS_DEFAULT +# define MTDIDS_DEFAULT "nand0=fsl_elbc_nand" +#endif /* MTDIDS_DEFAULT */ + +#ifndef MTDPARTS_DEFAULT +# define MTDPARTS_DEFAULT "mtdparts=" \ + "fsl_elbc_nand:" \ + "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" +#endif /* MTDPARTS_DEFAULT */ + +/* architecture specific default bootargs */ +#define CONFIG_KM_DEF_BOOT_ARGS_CPU "" + +/* FIXME: FDT_ADDR is unspecified */ +#define CONFIG_KM_DEF_ENV_CPU \ + "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \ + "cramfsloadfdt=" \ + "cramfsload ${fdt_addr_r} " \ + "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \ + "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \ + "u-boot="__stringify(CONFIG_HOSTNAME) "/u-boot.pbl\0" \ + "update=" \ + "sf probe 0;sf erase 0 +${filesize};" \ + "sf write ${load_addr_r} 0 ${filesize};\0" \ + "" + +#define CONFIG_HW_ENV_SETTINGS \ + "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \ + "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \ + "usb_dr_mode=host\0" + +#define CONFIG_KM_NEW_ENV \ + "newenv=sf probe 0;" \ + "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \ + __stringify(CONFIG_ENV_TOTAL_SIZE)"\0" + +/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */ +#ifndef CONFIG_KM_DEF_ARCH +#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_KM_DEF_ENV \ + CONFIG_KM_DEF_ARCH \ + CONFIG_KM_NEW_ENV \ + CONFIG_HW_ENV_SETTINGS \ + "EEprom_ivm=pca9547:70:9\0" \ + "" + +#endif /* _CONFIG_KMP204X_H */ diff --git a/include/configs/kmp204x.h b/include/configs/kmp204x.h new file mode 100644 index 0000000000..4158c8dd0f --- /dev/null +++ b/include/configs/kmp204x.h @@ -0,0 +1,68 @@ +/* + * (C) Copyright 2013 Keymile AG + * Valentin Longchamp + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* KMLION1 */ +#if defined(CONFIG_KMLION1) +#define CONFIG_HOSTNAME kmlion1 +#define CONFIG_KM_BOARD_NAME "kmlion1" + +#else +#error ("Board not supported") +#endif + +#define CONFIG_KMP204X + +#include "km/kmp204x-common.h" + +#if defined(CONFIG_KMLION1) +/* App1 Local bus */ +#define CONFIG_SYS_LBAPP1_BASE 0xD0000000 +#define CONFIG_SYS_LBAPP1_BASE_PHYS 0xFD0000000ull + +#define CONFIG_SYS_LBAPP1_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP1_BASE_PHYS) \ + | BR_PS_8 /* Port Size 8 bits */ \ + | BR_DECC_OFF /* no error corr */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_LBAPP1_OR_PRELIM (OR_AM_256MB /* length 256MB */ \ + | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \ + | OR_GPCM_CSNT /* LCS 1/4 clk before */ \ + | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ + | OR_GPCM_TRLX /* relaxed tmgs */ \ + | OR_GPCM_EAD) /* extra bus clk cycles */ +/* Local bus app1 Base Address */ +#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_LBAPP1_BR_PRELIM +/* Local bus app1 Options */ +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_LBAPP1_OR_PRELIM + +/* App2 Local bus */ +#define CONFIG_SYS_LBAPP2_BASE 0xE0000000 +#define CONFIG_SYS_LBAPP2_BASE_PHYS 0xFE0000000ull + +#define CONFIG_SYS_LBAPP2_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP2_BASE_PHYS) \ + | BR_PS_8 /* Port Size 8 bits */ \ + | BR_DECC_OFF /* no error corr */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ + +#define CONFIG_SYS_LBAPP2_OR_PRELIM (OR_AM_256MB /* length 256MB */ \ + | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \ + | OR_GPCM_CSNT /* LCS 1/4 clk before */ \ + | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \ + | OR_GPCM_TRLX /* relaxed tmgs */ \ + | OR_GPCM_EAD) /* extra bus clk cycles */ +/* Local bus app2 Base Address */ +#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_LBAPP2_BR_PRELIM +/* Local bus app2 Options */ +#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_LBAPP2_OR_PRELIM +#endif + +#endif /* __CONFIG_H */ -- 2.25.1