From 6153248052b2e067df9596c2d619345261b1d3f7 Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Sun, 21 May 2017 21:20:44 +0200 Subject: [PATCH] lantiq: spi: double time out tolerance The generic SPI code calculates how long the issued transfer would take and adds 100ms in addition to the timeout as tolerance. On my 500 MHz Lantiq Mips SoC I am getting timeouts from the SPI like this when the system boots up: m25p80 spi32766.4: SPI transfer timed out blk_update_request: I/O error, dev mtdblock3, sector 2 SQUASHFS error: squashfs_read_data failed to read block 0x6e After increasing the tolerance for the timeout to 200ms I haven't seen these SPI transfer time outs any more. The Lantiq SPI driver in use here has an extra work queue in between, which gets triggered when the controller send the last word and the hardware FIFOs used for reading and writing are only 8 words long. Signed-off-by: Hauke Mehrtens --- .../0093-spi-double-time-out-tolerance.patch | 37 +++++++++++++++++++ 1 file changed, 37 insertions(+) create mode 100644 target/linux/lantiq/patches-4.9/0093-spi-double-time-out-tolerance.patch diff --git a/target/linux/lantiq/patches-4.9/0093-spi-double-time-out-tolerance.patch b/target/linux/lantiq/patches-4.9/0093-spi-double-time-out-tolerance.patch new file mode 100644 index 0000000000..68b0ffe570 --- /dev/null +++ b/target/linux/lantiq/patches-4.9/0093-spi-double-time-out-tolerance.patch @@ -0,0 +1,37 @@ +From 833bfade96561216aa2129516a5926a0326860a2 Mon Sep 17 00:00:00 2001 +From: Hauke Mehrtens +Date: Mon, 17 Apr 2017 01:38:05 +0200 +Subject: spi: double time out tolerance + +The generic SPI code calculates how long the issued transfer would take +and adds 100ms in addition to the timeout as tolerance. On my 500 MHz +Lantiq Mips SoC I am getting timeouts from the SPI like this when the +system boots up: + +m25p80 spi32766.4: SPI transfer timed out +blk_update_request: I/O error, dev mtdblock3, sector 2 +SQUASHFS error: squashfs_read_data failed to read block 0x6e + +After increasing the tolerance for the timeout to 200ms I haven't seen +these SPI transfer time outs any more. +The Lantiq SPI driver in use here has an extra work queue in between, +which gets triggered when the controller send the last word and the +hardware FIFOs used for reading and writing are only 8 words long. + +Signed-off-by: Hauke Mehrtens +Signed-off-by: Mark Brown +--- + drivers/spi/spi.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/spi/spi.c ++++ b/drivers/spi/spi.c +@@ -1004,7 +1004,7 @@ static int spi_transfer_one_message(stru + ret = 0; + ms = 8LL * 1000LL * xfer->len; + do_div(ms, xfer->speed_hz); +- ms += ms + 100; /* some tolerance */ ++ ms += ms + 200; /* some tolerance */ + + if (ms > UINT_MAX) + ms = UINT_MAX; -- 2.25.1