From 47aefcc563b4052f7d383e9ab1c075037ffc566d Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Sun, 21 Sep 2014 21:58:02 +0000 Subject: [PATCH] bcm53xx: add nand flash driver Signed-off-by: Hauke Mehrtens SVN-Revision: 42641 --- target/linux/bcm53xx/Makefile | 2 +- target/linux/bcm53xx/config-3.14 | 12 +- .../patches-3.14/420-mtd-bcm5301x_nand.patch | 1616 +++++++++++++++++ 3 files changed, 1626 insertions(+), 4 deletions(-) create mode 100644 target/linux/bcm53xx/patches-3.14/420-mtd-bcm5301x_nand.patch diff --git a/target/linux/bcm53xx/Makefile b/target/linux/bcm53xx/Makefile index d41bf53130..daad42b369 100644 --- a/target/linux/bcm53xx/Makefile +++ b/target/linux/bcm53xx/Makefile @@ -9,7 +9,7 @@ include $(TOPDIR)/rules.mk ARCH:=arm BOARD:=bcm53xx BOARDNAME:=Broadcom BCM47xx/53xx (ARM) -FEATURES:=squashfs usb pci pcie gpio +FEATURES:=squashfs nand usb pci pcie gpio MAINTAINER:=Hauke Mehrtens CPU_TYPE:=cortex-a9 diff --git a/target/linux/bcm53xx/config-3.14 b/target/linux/bcm53xx/config-3.14 index f8610793bc..292752870c 100644 --- a/target/linux/bcm53xx/config-3.14 +++ b/target/linux/bcm53xx/config-3.14 @@ -82,12 +82,14 @@ CONFIG_DEBUG_BCM_5301X=y # CONFIG_DEBUG_BCM_KONA_UART is not set CONFIG_DEBUG_INFO=y CONFIG_DEBUG_LL=y -CONFIG_DEBUG_LL_INCLUDE="debug/pl01x.S" +CONFIG_DEBUG_LL_INCLUDE="debug/8250.S" # CONFIG_DEBUG_LL_UART_8250 is not set # CONFIG_DEBUG_LL_UART_PL01X is not set -# CONFIG_DEBUG_UART_8250 is not set +CONFIG_DEBUG_UART_8250=y +# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set +CONFIG_DEBUG_UART_8250_SHIFT=0 CONFIG_DEBUG_UART_PHYS=0x18000300 -CONFIG_DEBUG_UART_PL01X=y +# CONFIG_DEBUG_UART_PL01X is not set CONFIG_DEBUG_UART_VIRT=0xf1000300 CONFIG_DEBUG_UNCOMPRESS=y CONFIG_DEBUG_USER=y @@ -171,7 +173,11 @@ CONFIG_MDIO_BOARDINFO=y CONFIG_MIGHT_HAVE_PCI=y CONFIG_MODULES_USE_ELF_REL=y CONFIG_MTD_BCM47XX_PARTS=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_BCM=y +CONFIG_MTD_NAND_ECC=y # CONFIG_MTD_PHYSMAP_OF is not set +# CONFIG_MTD_SM_COMMON is not set CONFIG_MTD_SPI_BCM53XXSPIFLASH=y CONFIG_MTD_SPI_NOR=y # CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set diff --git a/target/linux/bcm53xx/patches-3.14/420-mtd-bcm5301x_nand.patch b/target/linux/bcm53xx/patches-3.14/420-mtd-bcm5301x_nand.patch new file mode 100644 index 0000000000..86c288d41e --- /dev/null +++ b/target/linux/bcm53xx/patches-3.14/420-mtd-bcm5301x_nand.patch @@ -0,0 +1,1616 @@ +--- a/drivers/mtd/nand/Kconfig ++++ b/drivers/mtd/nand/Kconfig +@@ -510,4 +510,10 @@ config MTD_NAND_XWAY + Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached + to the External Bus Unit (EBU). + ++config MTD_NAND_BCM ++ tristate "Support for NAND on some Broadcom SoC" ++ help ++ This driver is currently used for the NAND flash controller on the ++ Broadcom BCM5301X (NorthStar) SoCs. ++ + endif # MTD_NAND +--- a/drivers/mtd/nand/Makefile ++++ b/drivers/mtd/nand/Makefile +@@ -49,5 +49,6 @@ obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740 + obj-$(CONFIG_MTD_NAND_GPMI_NAND) += gpmi-nand/ + obj-$(CONFIG_MTD_NAND_XWAY) += xway_nand.o + obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH) += bcm47xxnflash/ ++obj-$(CONFIG_MTD_NAND_BCM) += bcm_nand.o + + nand-objs := nand_base.o nand_bbt.o +--- /dev/null ++++ b/drivers/mtd/nand/bcm_nand.c +@@ -0,0 +1,1591 @@ ++/* ++ * Nortstar NAND controller driver ++ * for Linux NAND library and MTD interface ++ * ++ * (c) Broadcom, Inc. 2012 All Rights Reserved. ++ * Copyright 2014 Hauke Mehrtens ++ * ++ * Licensed under the GNU/GPL. See COPYING for details. ++ * ++ * This module interfaces the NAND controller and hardware ECC capabilities ++ * tp the generic NAND chip support in the NAND library. ++ * ++ * Notes: ++ * This driver depends on generic NAND driver, but works at the ++ * page level for operations. ++ * ++ * When a page is written, the ECC calculated also protects the OOB ++ * bytes not taken by ECC, and so the OOB must be combined with any ++ * OOB data that preceded the page-write operation in order for the ++ * ECC to be calculated correctly. ++ * Also, when the page is erased, but OOB data is not, HW ECC will ++ * indicate an error, because it checks OOB too, which calls for some ++ * help from the software in this driver. ++ * ++ * TBD: ++ * Block locking/unlocking support, OTP support ++ */ ++ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++ ++#define NANDC_MAX_CHIPS 2 /* Only 2 CSn supported in NorthStar */ ++ ++#define DRV_NAME "bcmnand" ++#define DRV_DESC "Northstar on-chip NAND Flash Controller driver" ++ ++/* ++ * Driver private control structure ++ */ ++struct bcmnand_ctrl { ++ struct mtd_info mtd; ++ struct nand_chip nand; ++ struct bcma_device *core; ++ ++ struct completion op_completion; ++ ++ struct nand_ecclayout ecclayout; ++ int cmd_ret; /* saved error code */ ++ unsigned char oob_index; ++ unsigned char id_byte_index; ++ unsigned char chip_num; ++ unsigned char last_cmd; ++ unsigned char ecc_level; ++ unsigned char sector_size_shift; ++ unsigned char sec_per_page_shift; ++}; ++ ++ ++/* ++ * IRQ numbers - offset from first irq in nandc_irq resource ++ */ ++#define NANDC_IRQ_RD_MISS 0 ++#define NANDC_IRQ_ERASE_COMPLETE 1 ++#define NANDC_IRQ_COPYBACK_COMPLETE 2 ++#define NANDC_IRQ_PROGRAM_COMPLETE 3 ++#define NANDC_IRQ_CONTROLLER_RDY 4 ++#define NANDC_IRQ_RDBSY_RDY 5 ++#define NANDC_IRQ_ECC_UNCORRECTABLE 6 ++#define NANDC_IRQ_ECC_CORRECTABLE 7 ++#define NANDC_IRQ_NUM 8 ++ ++struct bcmnand_reg_field { ++ unsigned int reg; ++ unsigned int pos; ++ unsigned int width; ++}; ++ ++/* ++ * REGISTERS ++ * ++ * Individual bit-fields aof registers are specificed here ++ * for clarity, and the rest of the code will access each field ++ * as if it was its own register. ++ * ++ * Following registers are off : ++ */ ++#define REG_BIT_FIELD(r, p, w) ((struct bcmnand_reg_field){(r), (p), (w)}) ++ ++#define NANDC_8KB_PAGE_SUPPORT REG_BIT_FIELD(0x0, 31, 1) ++#define NANDC_REV_MAJOR REG_BIT_FIELD(0x0, 8, 8) ++#define NANDC_REV_MINOR REG_BIT_FIELD(0x0, 0, 8) ++ ++#define NANDC_CMD_START_OPCODE REG_BIT_FIELD(0x4, 24, 5) ++ ++#define NANDC_CMD_CS_SEL REG_BIT_FIELD(0x8, 16, 3) ++#define NANDC_CMD_EXT_ADDR REG_BIT_FIELD(0x8, 0, 16) ++ ++#define NANDC_CMD_ADDRESS REG_BIT_FIELD(0xc, 0, 32) ++#define NANDC_CMD_END_ADDRESS REG_BIT_FIELD(0x10, 0, 32) ++ ++#define NANDC_INT_STATUS REG_BIT_FIELD(0x14, 0, 32) ++#define NANDC_INT_STAT_CTLR_RDY REG_BIT_FIELD(0x14, 31, 1) ++#define NANDC_INT_STAT_FLASH_RDY REG_BIT_FIELD(0x14, 30, 1) ++#define NANDC_INT_STAT_CACHE_VALID REG_BIT_FIELD(0x14, 29, 1) ++#define NANDC_INT_STAT_SPARE_VALID REG_BIT_FIELD(0x14, 28, 1) ++#define NANDC_INT_STAT_ERASED REG_BIT_FIELD(0x14, 27, 1) ++#define NANDC_INT_STAT_PLANE_RDY REG_BIT_FIELD(0x14, 26, 1) ++#define NANDC_INT_STAT_FLASH_STATUS REG_BIT_FIELD(0x14, 0, 8) ++ ++#define NANDC_CS_LOCK REG_BIT_FIELD(0x18, 31, 1) ++#define NANDC_CS_AUTO_CONFIG REG_BIT_FIELD(0x18, 30, 1) ++#define NANDC_CS_NAND_WP REG_BIT_FIELD(0x18, 29, 1) ++#define NANDC_CS_BLK0_WP REG_BIT_FIELD(0x18, 28, 1) ++#define NANDC_CS_SW_USING_CS(n) REG_BIT_FIELD(0x18, 8+(n), 1) ++#define NANDC_CS_MAP_SEL_CS(n) REG_BIT_FIELD(0x18, 0+(n), 1) ++ ++#define NANDC_XOR_ADDR_BLK0_ONLY REG_BIT_FIELD(0x1c, 31, 1) ++#define NANDC_XOR_ADDR_CS(n) REG_BIT_FIELD(0x1c, 0+(n), 1) ++ ++#define NANDC_LL_OP_RET_IDLE REG_BIT_FIELD(0x20, 31, 1) ++#define NANDC_LL_OP_CLE REG_BIT_FIELD(0x20, 19, 1) ++#define NANDC_LL_OP_ALE REG_BIT_FIELD(0x20, 18, 1) ++#define NANDC_LL_OP_WE REG_BIT_FIELD(0x20, 17, 1) ++#define NANDC_LL_OP_RE REG_BIT_FIELD(0x20, 16, 1) ++#define NANDC_LL_OP_DATA REG_BIT_FIELD(0x20, 0, 16) ++ ++#define NANDC_MPLANE_ADDR_EXT REG_BIT_FIELD(0x24, 0, 16) ++#define NANDC_MPLANE_ADDR REG_BIT_FIELD(0x28, 0, 32) ++ ++#define NANDC_ACC_CTRL_CS(n) REG_BIT_FIELD(0x50+((n)<<4), 0, 32) ++#define NANDC_ACC_CTRL_RD_ECC(n) REG_BIT_FIELD(0x50+((n)<<4), 31, 1) ++#define NANDC_ACC_CTRL_WR_ECC(n) REG_BIT_FIELD(0x50+((n)<<4), 30, 1) ++#define NANDC_ACC_CTRL_CE_CARE(n) REG_BIT_FIELD(0x50+((n)<<4), 29, 1) ++#define NANDC_ACC_CTRL_PGM_RDIN(n) REG_BIT_FIELD(0x50+((n)<<4), 28, 1) ++#define NANDC_ACC_CTRL_ERA_ECC_ERR(n) REG_BIT_FIELD(0x50+((n)<<4), 27, 1) ++#define NANDC_ACC_CTRL_PGM_PARTIAL(n) REG_BIT_FIELD(0x50+((n)<<4), 26, 1) ++#define NANDC_ACC_CTRL_WR_PREEMPT(n) REG_BIT_FIELD(0x50+((n)<<4), 25, 1) ++#define NANDC_ACC_CTRL_PG_HIT(n) REG_BIT_FIELD(0x50+((n)<<4), 24, 1) ++#define NANDC_ACC_CTRL_PREFETCH(n) REG_BIT_FIELD(0x50+((n)<<4), 23, 1) ++#define NANDC_ACC_CTRL_CACHE_MODE(n) REG_BIT_FIELD(0x50+((n)<<4), 22, 1) ++#define NANDC_ACC_CTRL_CACHE_LASTPG(n) REG_BIT_FIELD(0x50+((n)<<4), 21, 1) ++#define NANDC_ACC_CTRL_ECC_LEVEL(n) REG_BIT_FIELD(0x50+((n)<<4), 16, 5) ++#define NANDC_ACC_CTRL_SECTOR_1K(n) REG_BIT_FIELD(0x50+((n)<<4), 7, 1) ++#define NANDC_ACC_CTRL_SPARE_SIZE(n) REG_BIT_FIELD(0x50+((n)<<4), 0, 7) ++ ++#define NANDC_CONFIG_CS(n) REG_BIT_FIELD(0x54+((n)<<4), 0, 32) ++#define NANDC_CONFIG_LOCK(n) REG_BIT_FIELD(0x54+((n)<<4), 31, 1) ++#define NANDC_CONFIG_BLK_SIZE(n) REG_BIT_FIELD(0x54+((n)<<4), 28, 3) ++#define NANDC_CONFIG_CHIP_SIZE(n) REG_BIT_FIELD(0x54+((n)<<4), 24, 4) ++#define NANDC_CONFIG_CHIP_WIDTH(n) REG_BIT_FIELD(0x54+((n)<<4), 23, 1) ++#define NANDC_CONFIG_PAGE_SIZE(n) REG_BIT_FIELD(0x54+((n)<<4), 20, 2) ++#define NANDC_CONFIG_FUL_ADDR_BYTES(n) REG_BIT_FIELD(0x54+((n)<<4), 16, 3) ++#define NANDC_CONFIG_COL_ADDR_BYTES(n) REG_BIT_FIELD(0x54+((n)<<4), 12, 3) ++#define NANDC_CONFIG_BLK_ADDR_BYTES(n) REG_BIT_FIELD(0x54+((n)<<4), 8, 3) ++ ++#define NANDC_TIMING_1_CS(n) REG_BIT_FIELD(0x58+((n)<<4), 0, 32) ++#define NANDC_TIMING_2_CS(n) REG_BIT_FIELD(0x5c+((n)<<4), 0, 32) ++ /* Individual bits for Timing registers - TBD */ ++ ++#define NANDC_CORR_STAT_THRESH_CS(n) REG_BIT_FIELD(0xc0, 6*(n), 6) ++ ++#define NANDC_BLK_WP_END_ADDR REG_BIT_FIELD(0xc8, 0, 32) ++ ++#define NANDC_MPLANE_ERASE_CYC2_OPCODE REG_BIT_FIELD(0xcc, 24, 8) ++#define NANDC_MPLANE_READ_STAT_OPCODE REG_BIT_FIELD(0xcc, 16, 8) ++#define NANDC_MPLANE_PROG_ODD_OPCODE REG_BIT_FIELD(0xcc, 8, 8) ++#define NANDC_MPLANE_PROG_TRL_OPCODE REG_BIT_FIELD(0xcc, 0, 8) ++ ++#define NANDC_MPLANE_PGCACHE_TRL_OPCODE REG_BIT_FIELD(0xd0, 24, 8) ++#define NANDC_MPLANE_READ_STAT2_OPCODE REG_BIT_FIELD(0xd0, 16, 8) ++#define NANDC_MPLANE_READ_EVEN_OPCODE REG_BIT_FIELD(0xd0, 8, 8) ++#define NANDC_MPLANE_READ_ODD__OPCODE REG_BIT_FIELD(0xd0, 0, 8) ++ ++#define NANDC_MPLANE_CTRL_ERASE_CYC2_EN REG_BIT_FIELD(0xd4, 31, 1) ++#define NANDC_MPLANE_CTRL_RD_ADDR_SIZE REG_BIT_FIELD(0xd4, 30, 1) ++#define NANDC_MPLANE_CTRL_RD_CYC_ADDR REG_BIT_FIELD(0xd4, 29, 1) ++#define NANDC_MPLANE_CTRL_RD_COL_ADDR REG_BIT_FIELD(0xd4, 28, 1) ++ ++#define NANDC_UNCORR_ERR_COUNT REG_BIT_FIELD(0xfc, 0, 32) ++ ++#define NANDC_CORR_ERR_COUNT REG_BIT_FIELD(0x100, 0, 32) ++ ++#define NANDC_READ_CORR_BIT_COUNT REG_BIT_FIELD(0x104, 0, 32) ++ ++#define NANDC_BLOCK_LOCK_STATUS REG_BIT_FIELD(0x108, 0, 8) ++ ++#define NANDC_ECC_CORR_ADDR_CS REG_BIT_FIELD(0x10c, 16, 3) ++#define NANDC_ECC_CORR_ADDR_EXT REG_BIT_FIELD(0x10c, 0, 16) ++ ++#define NANDC_ECC_CORR_ADDR REG_BIT_FIELD(0x110, 0, 32) ++ ++#define NANDC_ECC_UNC_ADDR_CS REG_BIT_FIELD(0x114, 16, 3) ++#define NANDC_ECC_UNC_ADDR_EXT REG_BIT_FIELD(0x114, 0, 16) ++ ++#define NANDC_ECC_UNC_ADDR REG_BIT_FIELD(0x118, 0, 32) ++ ++#define NANDC_READ_ADDR_CS REG_BIT_FIELD(0x11c, 16, 3) ++#define NANDC_READ_ADDR_EXT REG_BIT_FIELD(0x11c, 0, 16) ++#define NANDC_READ_ADDR REG_BIT_FIELD(0x120, 0, 32) ++ ++#define NANDC_PROG_ADDR_CS REG_BIT_FIELD(0x124, 16, 3) ++#define NANDC_PROG_ADDR_EXT REG_BIT_FIELD(0x124, 0, 16) ++#define NANDC_PROG_ADDR REG_BIT_FIELD(0x128, 0, 32) ++ ++#define NANDC_CPYBK_ADDR_CS REG_BIT_FIELD(0x12c, 16, 3) ++#define NANDC_CPYBK_ADDR_EXT REG_BIT_FIELD(0x12c, 0, 16) ++#define NANDC_CPYBK_ADDR REG_BIT_FIELD(0x130, 0, 32) ++ ++#define NANDC_ERASE_ADDR_CS REG_BIT_FIELD(0x134, 16, 3) ++#define NANDC_ERASE_ADDR_EXT REG_BIT_FIELD(0x134, 0, 16) ++#define NANDC_ERASE_ADDR REG_BIT_FIELD(0x138, 0, 32) ++ ++#define NANDC_INV_READ_ADDR_CS REG_BIT_FIELD(0x13c, 16, 3) ++#define NANDC_INV_READ_ADDR_EXT REG_BIT_FIELD(0x13c, 0, 16) ++#define NANDC_INV_READ_ADDR REG_BIT_FIELD(0x140, 0, 32) ++ ++#define NANDC_INIT_STAT REG_BIT_FIELD(0x144, 0, 32) ++#define NANDC_INIT_ONFI_DONE REG_BIT_FIELD(0x144, 31, 1) ++#define NANDC_INIT_DEVID_DONE REG_BIT_FIELD(0x144, 30, 1) ++#define NANDC_INIT_SUCCESS REG_BIT_FIELD(0x144, 29, 1) ++#define NANDC_INIT_FAIL REG_BIT_FIELD(0x144, 28, 1) ++#define NANDC_INIT_BLANK REG_BIT_FIELD(0x144, 27, 1) ++#define NANDC_INIT_TIMEOUT REG_BIT_FIELD(0x144, 26, 1) ++#define NANDC_INIT_UNC_ERROR REG_BIT_FIELD(0x144, 25, 1) ++#define NANDC_INIT_CORR_ERROR REG_BIT_FIELD(0x144, 24, 1) ++#define NANDC_INIT_PARAM_RDY REG_BIT_FIELD(0x144, 23, 1) ++#define NANDC_INIT_AUTH_FAIL REG_BIT_FIELD(0x144, 22, 1) ++ ++#define NANDC_ONFI_STAT REG_BIT_FIELD(0x148, 0, 32) ++#define NANDC_ONFI_DEBUG REG_BIT_FIELD(0x148, 28, 4) ++#define NANDC_ONFI_PRESENT REG_BIT_FIELD(0x148, 27, 1) ++#define NANDC_ONFI_BADID_PG2 REG_BIT_FIELD(0x148, 5, 1) ++#define NANDC_ONFI_BADID_PG1 REG_BIT_FIELD(0x148, 4, 1) ++#define NANDC_ONFI_BADID_PG0 REG_BIT_FIELD(0x148, 3, 1) ++#define NANDC_ONFI_BADCRC_PG2 REG_BIT_FIELD(0x148, 2, 1) ++#define NANDC_ONFI_BADCRC_PG1 REG_BIT_FIELD(0x148, 1, 1) ++#define NANDC_ONFI_BADCRC_PG0 REG_BIT_FIELD(0x148, 0, 1) ++ ++#define NANDC_ONFI_DEBUG_DATA REG_BIT_FIELD(0x14c, 0, 32) ++ ++#define NANDC_SEMAPHORE REG_BIT_FIELD(0x150, 0, 8) ++ ++#define NANDC_DEVID_BYTE(b) REG_BIT_FIELD(0x194+((b)&0x4), \ ++ 24-(((b)&3)<<3), 8) ++ ++#define NANDC_LL_RDDATA REG_BIT_FIELD(0x19c, 0, 16) ++ ++#define NANDC_INT_N_REG(n) REG_BIT_FIELD(0xf00|((n)<<2), 0, 1) ++#define NANDC_INT_DIREC_READ_MISS REG_BIT_FIELD(0xf00, 0, 1) ++#define NANDC_INT_ERASE_DONE REG_BIT_FIELD(0xf04, 0, 1) ++#define NANDC_INT_CPYBK_DONE REG_BIT_FIELD(0xf08, 0, 1) ++#define NANDC_INT_PROGRAM_DONE REG_BIT_FIELD(0xf0c, 0, 1) ++#define NANDC_INT_CONTROLLER_RDY REG_BIT_FIELD(0xf10, 0, 1) ++#define NANDC_INT_RDBSY_RDY REG_BIT_FIELD(0xf14, 0, 1) ++#define NANDC_INT_ECC_UNCORRECTABLE REG_BIT_FIELD(0xf18, 0, 1) ++#define NANDC_INT_ECC_CORRECTABLE REG_BIT_FIELD(0xf1c, 0, 1) ++ ++/* ++ * Following registers are treated as contigous IO memory, offset is from ++ * , and the data is in big-endian byte order ++ */ ++#define NANDC_SPARE_AREA_READ_OFF 0x200 ++#define NANDC_SPARE_AREA_WRITE_OFF 0x280 ++#define NANDC_CACHE_OFF 0x400 ++#define NANDC_CACHE_SIZE (128*4) ++ ++struct bcmnand_areg_field { ++ unsigned int reg; ++ unsigned int pos; ++ unsigned int width; ++}; ++ ++/* ++ * Following are IDM (a.k.a. Slave Wrapper) registers are off : ++ */ ++#define IDMREG_BIT_FIELD(r, p, w) ((struct bcmnand_areg_field){(r), (p), (w)}) ++ ++#define NANDC_IDM_AXI_BIG_ENDIAN IDMREG_BIT_FIELD(0x408, 28, 1) ++#define NANDC_IDM_APB_LITTLE_ENDIAN IDMREG_BIT_FIELD(0x408, 24, 1) ++#define NANDC_IDM_TM IDMREG_BIT_FIELD(0x408, 16, 5) ++#define NANDC_IDM_IRQ_CORRECABLE_EN IDMREG_BIT_FIELD(0x408, 9, 1) ++#define NANDC_IDM_IRQ_UNCORRECABLE_EN IDMREG_BIT_FIELD(0x408, 8, 1) ++#define NANDC_IDM_IRQ_RDYBSY_RDY_EN IDMREG_BIT_FIELD(0x408, 7, 1) ++#define NANDC_IDM_IRQ_CONTROLLER_RDY_EN IDMREG_BIT_FIELD(0x408, 6, 1) ++#define NANDC_IDM_IRQ_PRPOGRAM_COMP_EN IDMREG_BIT_FIELD(0x408, 5, 1) ++#define NANDC_IDM_IRQ_COPYBK_COMP_EN IDMREG_BIT_FIELD(0x408, 4, 1) ++#define NANDC_IDM_IRQ_ERASE_COMP_EN IDMREG_BIT_FIELD(0x408, 3, 1) ++#define NANDC_IDM_IRQ_READ_MISS_EN IDMREG_BIT_FIELD(0x408, 2, 1) ++#define NANDC_IDM_IRQ_N_EN(n) IDMREG_BIT_FIELD(0x408, 2+(n), 1) ++ ++#define NANDC_IDM_CLOCK_EN IDMREG_BIT_FIELD(0x408, 0, 1) ++ ++#define NANDC_IDM_IO_ECC_CORR IDMREG_BIT_FIELD(0x500, 3, 1) ++#define NANDC_IDM_IO_ECC_UNCORR IDMREG_BIT_FIELD(0x500, 2, 1) ++#define NANDC_IDM_IO_RDYBSY IDMREG_BIT_FIELD(0x500, 1, 1) ++#define NANDC_IDM_IO_CTRL_RDY IDMREG_BIT_FIELD(0x500, 0, 1) ++ ++#define NANDC_IDM_RESET IDMREG_BIT_FIELD(0x800, 0, 1) ++ /* Remaining IDM registers do not seem to be useful, skipped */ ++ ++/* ++ * NAND Controller has its own command opcodes ++ * different from opcodes sent to the actual flash chip ++ */ ++#define NANDC_CMD_OPCODE_NULL 0 ++#define NANDC_CMD_OPCODE_PAGE_READ 1 ++#define NANDC_CMD_OPCODE_SPARE_READ 2 ++#define NANDC_CMD_OPCODE_STATUS_READ 3 ++#define NANDC_CMD_OPCODE_PAGE_PROG 4 ++#define NANDC_CMD_OPCODE_SPARE_PROG 5 ++#define NANDC_CMD_OPCODE_DEVID_READ 7 ++#define NANDC_CMD_OPCODE_BLOCK_ERASE 8 ++#define NANDC_CMD_OPCODE_FLASH_RESET 9 ++ ++/* ++ * NAND Controller hardware ECC data size ++ * ++ * The following table contains the number of bytes needed for ++ * each of the ECC levels, per "sector", which is either 512 or 1024 bytes. ++ * The actual layout is as follows: ++ * The entire spare area is equally divided into as many sections as there ++ * are sectors per page, and the ECC data is located at the end of each ++ * of these sections. ++ * For example, given a 2K per page and 64 bytes spare device, configured for ++ * sector size 1k and ECC level of 4, the spare area will be divided into 2 ++ * sections 32 bytes each, and the last 14 bytes of 32 in each section will ++ * be filled with ECC data. ++ * Note: the name of the algorythm and the number of error bits it can correct ++ * is of no consequence to this driver, therefore omitted. ++ */ ++struct bcmnand_ecc_size_s { ++ unsigned char sector_size_shift; ++ unsigned char ecc_level; ++ unsigned char ecc_bytes_per_sec; ++ unsigned char reserved; ++}; ++ ++static const struct bcmnand_ecc_size_s bcmnand_ecc_sizes[] = { ++ { 9, 0, 0 }, ++ { 10, 0, 0 }, ++ { 9, 1, 2 }, ++ { 10, 1, 4 }, ++ { 9, 2, 4 }, ++ { 10, 2, 7 }, ++ { 9, 3, 6 }, ++ { 10, 3, 11 }, ++ { 9, 4, 7 }, ++ { 10, 4, 14 }, ++ { 9, 5, 9 }, ++ { 10, 5, 18 }, ++ { 9, 6, 11 }, ++ { 10, 6, 21 }, ++ { 9, 7, 13 }, ++ { 10, 7, 25 }, ++ { 9, 8, 14 }, ++ { 10, 8, 28 }, ++ ++ { 9, 9, 16 }, ++ { 9, 10, 18 }, ++ { 9, 11, 20 }, ++ { 9, 12, 21 }, ++ ++ { 10, 9, 32 }, ++ { 10, 10, 35 }, ++ { 10, 11, 39 }, ++ { 10, 12, 42 }, ++}; ++ ++/* ++ * Populate the various fields that depend on how ++ * the hardware ECC data is located in the spare area ++ * ++ * For this controiller, it is easier to fill-in these ++ * structures at run time. ++ * ++ * The bad-block marker is assumed to occupy one byte ++ * at chip->badblockpos, which must be in the first ++ * sector of the spare area, namely it is either ++ * at offset 0 or 5. ++ * Some chips use both for manufacturer's bad block ++ * markers, but we ingore that issue here, and assume only ++ * one byte is used as bad-block marker always. ++ */ ++static int bcmnand_hw_ecc_layout(struct bcmnand_ctrl *ctrl) ++{ ++ struct nand_ecclayout *layout; ++ unsigned int i, j, k; ++ unsigned int ecc_per_sec, oob_per_sec; ++ unsigned int bbm_pos = ctrl->nand.badblockpos; ++ ++ /* Caclculate spare area per sector size */ ++ oob_per_sec = ctrl->mtd.oobsize >> ctrl->sec_per_page_shift; ++ ++ /* Try to calculate the amount of ECC bytes per sector with a formula */ ++ if (ctrl->sector_size_shift == 9) ++ ecc_per_sec = ((ctrl->ecc_level * 14) + 7) >> 3; ++ else if (ctrl->sector_size_shift == 10) ++ ecc_per_sec = ((ctrl->ecc_level * 14) + 3) >> 2; ++ else ++ ecc_per_sec = oob_per_sec + 1; /* cause an error if not in table */ ++ ++ /* Now find out the answer according to the table */ ++ for (i = 0; i < ARRAY_SIZE(bcmnand_ecc_sizes); i++) { ++ if (bcmnand_ecc_sizes[i].ecc_level == ctrl->ecc_level && ++ bcmnand_ecc_sizes[i].sector_size_shift == ++ ctrl->sector_size_shift) { ++ break; ++ } ++ } ++ ++ /* Table match overrides formula */ ++ if (bcmnand_ecc_sizes[i].ecc_level == ctrl->ecc_level && ++ bcmnand_ecc_sizes[i].sector_size_shift == ctrl->sector_size_shift) ++ ecc_per_sec = bcmnand_ecc_sizes[i].ecc_bytes_per_sec; ++ ++ /* Return an error if calculated ECC leaves no room for OOB */ ++ if ((ctrl->sec_per_page_shift != 0 && ecc_per_sec >= oob_per_sec) || ++ (ctrl->sec_per_page_shift == 0 && ecc_per_sec >= (oob_per_sec - 1))) { ++ pr_err("%s: ECC level %d too high, leaves no room for OOB data\n", ++ DRV_NAME, ctrl->ecc_level); ++ return -EINVAL; ++ } ++ ++ /* Fill in the needed fields */ ++ ctrl->nand.ecc.size = ctrl->mtd.writesize >> ctrl->sec_per_page_shift; ++ ctrl->nand.ecc.bytes = ecc_per_sec; ++ ctrl->nand.ecc.steps = 1 << ctrl->sec_per_page_shift; ++ ctrl->nand.ecc.total = ecc_per_sec << ctrl->sec_per_page_shift; ++ ctrl->nand.ecc.strength = ctrl->ecc_level; ++ ++ /* Build an ecc layout data structure */ ++ layout = &ctrl->ecclayout; ++ memset(layout, 0, sizeof(*layout)); ++ ++ /* Total number of bytes used by HW ECC */ ++ layout->eccbytes = ecc_per_sec << ctrl->sec_per_page_shift; ++ ++ /* Location for each of the HW ECC bytes */ ++ for (i = j = 0, k = 1; ++ i < ARRAY_SIZE(layout->eccpos) && i < layout->eccbytes; ++ i++, j++) { ++ /* switch sector # */ ++ if (j == ecc_per_sec) { ++ j = 0; ++ k++; ++ } ++ /* save position of each HW-generated ECC byte */ ++ layout->eccpos[i] = (oob_per_sec * k) - ecc_per_sec + j; ++ ++ /* Check that HW ECC does not overlap bad-block marker */ ++ if (bbm_pos == layout->eccpos[i]) { ++ pr_err("%s: ECC level %d too high, HW ECC collides with bad-block marker position\n", ++ DRV_NAME, ctrl->ecc_level); ++ return -EINVAL; ++ } ++ } ++ ++ /* Location of all user-available OOB byte-ranges */ ++ for (i = 0; i < ARRAY_SIZE(layout->oobfree); i++) { ++ struct nand_oobfree *oobfree = &layout->oobfree[i]; ++ ++ if (i >= (1 << ctrl->sec_per_page_shift)) ++ break; ++ oobfree->offset = oob_per_sec * i; ++ oobfree->length = oob_per_sec - ecc_per_sec; ++ ++ /* Bad-block marker must be in the first sector spare area */ ++ if (WARN_ON(bbm_pos >= (oobfree->offset + oobfree->length))) ++ return -EINVAL; ++ ++ if (i != 0) ++ continue; ++ ++ /* Remove bad-block marker from available byte range */ ++ if (bbm_pos == oobfree->offset) { ++ oobfree->offset += 1; ++ oobfree->length -= 1; ++ } else if (bbm_pos == (oobfree->offset + oobfree->length - 1)) { ++ oobfree->length -= 1; ++ } else { ++ layout->oobfree[i + 1].offset = bbm_pos + 1; ++ layout->oobfree[i + 1].length = ++ oobfree->length - bbm_pos - 1; ++ oobfree->length = bbm_pos; ++ i++; ++ } ++ } ++ ++ layout->oobavail = ((oob_per_sec - ecc_per_sec) ++ << ctrl->sec_per_page_shift) - 1; ++ ++ ctrl->mtd.oobavail = layout->oobavail; ++ ctrl->nand.ecc.layout = layout; ++ ++ /* Output layout for debugging */ ++ pr_debug("%s: Spare area=%d eccbytes %d, ecc bytes located at:\n", ++ DRV_NAME, ctrl->mtd.oobsize, layout->eccbytes); ++ for (i = j = 0; ++ i < ARRAY_SIZE(layout->eccpos) && i < layout->eccbytes; i++) ++ pr_debug(" %d", layout->eccpos[i]); ++ ++ pr_debug("\n%s: Available %d bytes at (off,len):\n", DRV_NAME, ++ layout->oobavail); ++ for (i = 0; i < ARRAY_SIZE(layout->oobfree); i++) ++ pr_debug("(%d,%d) ", layout->oobfree[i].offset, ++ layout->oobfree[i].length); ++ ++ pr_debug("\n"); ++ ++ return 0; ++} ++ ++/* ++ * Register bit-field manipulation routines ++ */ ++ ++static inline unsigned int bcmnand_reg_read(struct bcmnand_ctrl *ctrl, ++ struct bcmnand_reg_field rbf) ++{ ++ u32 val; ++ ++ val = bcma_read32(ctrl->core, rbf.reg); ++ val >>= rbf.pos; ++ val &= (1 << rbf.width) - 1; ++ ++ return val; ++} ++ ++static inline void bcmnand_reg_write(struct bcmnand_ctrl *ctrl, ++ struct bcmnand_reg_field rbf, ++ unsigned newval) ++{ ++ u32 val, msk; ++ ++ msk = (1 << rbf.width) - 1; ++ msk <<= rbf.pos; ++ newval <<= rbf.pos; ++ newval &= msk; ++ ++ val = bcma_read32(ctrl->core, rbf.reg); ++ val &= ~msk; ++ val |= newval; ++ bcma_write32(ctrl->core, rbf.reg, val); ++} ++ ++static inline unsigned int bcmnand_reg_aread(struct bcmnand_ctrl *ctrl, ++ struct bcmnand_areg_field rbf) ++{ ++ u32 val; ++ ++ val = bcma_aread32(ctrl->core, rbf.reg); ++ val >>= rbf.pos; ++ val &= (1 << rbf.width) - 1; ++ ++ return val; ++} ++ ++static inline void bcmnand_reg_awrite(struct bcmnand_ctrl *ctrl, ++ struct bcmnand_areg_field rbf, ++ unsigned int newval) ++{ ++ u32 val, msk; ++ ++ msk = (1 << rbf.width) - 1; ++ msk <<= rbf.pos; ++ newval <<= rbf.pos; ++ newval &= msk; ++ ++ val = bcma_aread32(ctrl->core, rbf.reg); ++ val &= ~msk; ++ val |= newval; ++ bcma_awrite32(ctrl->core, rbf.reg, val); ++} ++ ++/* ++ * NAND Interface - dev_ready ++ * ++ * Return 1 iff device is ready, 0 otherwise ++ */ ++static int bcmnand_dev_ready(struct mtd_info *mtd) ++{ ++ struct nand_chip *chip = mtd->priv; ++ struct bcmnand_ctrl *ctrl = chip->priv; ++ ++ return bcmnand_reg_aread(ctrl, NANDC_IDM_IO_CTRL_RDY); ++} ++ ++/* ++ * Interrupt service routines ++ */ ++static irqreturn_t bcmnand_isr(int irq, void *dev_id) ++{ ++ struct bcmnand_ctrl *ctrl = dev_id; ++ int irq_off; ++ ++ irq_off = irq - ctrl->core->irq; ++ WARN_ON(irq_off < 0 || irq_off >= NANDC_IRQ_NUM); ++ ++ if (!bcmnand_reg_read(ctrl, NANDC_INT_N_REG(irq_off))) ++ return IRQ_NONE; ++ ++ /* Acknowledge interrupt */ ++ bcmnand_reg_write(ctrl, NANDC_INT_N_REG(irq_off), 1); ++ ++ /* Wake up task */ ++ complete(&ctrl->op_completion); ++ ++ return IRQ_HANDLED; ++} ++ ++static int bcmnand_wait_interrupt(struct bcmnand_ctrl *ctrl, ++ unsigned int irq_off, ++ unsigned int timeout_usec) ++{ ++ long timeout_jiffies; ++ int ret = 0; ++ ++ reinit_completion(&ctrl->op_completion); ++ ++ /* Acknowledge interrupt */ ++ bcmnand_reg_write(ctrl, NANDC_INT_N_REG(irq_off), 1); ++ ++ /* Enable IRQ to wait on */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_IRQ_N_EN(irq_off), 1); ++ ++ timeout_jiffies = 1 + usecs_to_jiffies(timeout_usec); ++ ++ if (irq_off != NANDC_IRQ_CONTROLLER_RDY || ++ 0 == bcmnand_reg_aread(ctrl, NANDC_IDM_IO_CTRL_RDY)) { ++ ++ timeout_jiffies = wait_for_completion_interruptible_timeout( ++ &ctrl->op_completion, timeout_jiffies); ++ ++ if (timeout_jiffies < 0) ++ ret = timeout_jiffies; ++ if (timeout_jiffies == 0) ++ ret = -ETIME; ++ } ++ ++ /* Disable IRQ, we're done waiting */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_IRQ_N_EN(irq_off), 0); ++ ++ if (bcmnand_reg_aread(ctrl, NANDC_IDM_IO_CTRL_RDY)) ++ ret = 0; ++ ++ return ret; ++} ++ ++/* ++ * wait for command completion ++ */ ++static int bcmnand_wait_cmd(struct bcmnand_ctrl *ctrl, unsigned int timeout_usec) ++{ ++ unsigned int retries; ++ ++ if (bcmnand_reg_read(ctrl, NANDC_INT_STAT_CTLR_RDY)) ++ return 0; ++ ++ /* If the timeout is long, wait for interrupt */ ++ if (timeout_usec >= jiffies_to_usecs(1) >> 4) ++ return bcmnand_wait_interrupt( ++ ctrl, NANDC_IRQ_CONTROLLER_RDY, timeout_usec); ++ ++ /* Wait for completion of the prior command */ ++ retries = (timeout_usec >> 3) + 1; ++ ++ while (retries-- && ++ 0 == bcmnand_reg_read(ctrl, NANDC_INT_STAT_CTLR_RDY)) { ++ cpu_relax(); ++ udelay(6); ++ } ++ ++ if (retries == 0) ++ return -ETIME; ++ ++ return 0; ++} ++ ++ ++/* ++ * NAND Interface - waitfunc ++ */ ++static int bcmnand_waitfunc(struct mtd_info *mtd, struct nand_chip *chip) ++{ ++ struct bcmnand_ctrl *ctrl = chip->priv; ++ unsigned int to; ++ int ret; ++ ++ /* figure out timeout based on what command is on */ ++ switch (ctrl->last_cmd) { ++ default: ++ case NAND_CMD_ERASE1: ++ case NAND_CMD_ERASE2: ++ to = 1 << 16; ++ break; ++ case NAND_CMD_STATUS: ++ case NAND_CMD_RESET: ++ to = 256; ++ break; ++ case NAND_CMD_READID: ++ to = 1024; ++ break; ++ case NAND_CMD_READ1: ++ case NAND_CMD_READ0: ++ to = 2048; ++ break; ++ case NAND_CMD_PAGEPROG: ++ to = 4096; ++ break; ++ case NAND_CMD_READOOB: ++ to = 512; ++ break; ++ } ++ ++ /* deliver deferred error code if any */ ++ ret = ctrl->cmd_ret; ++ if (ret < 0) ++ ctrl->cmd_ret = 0; ++ else ++ ret = bcmnand_wait_cmd(ctrl, to); ++ ++ /* Timeout */ ++ if (ret < 0) ++ return NAND_STATUS_FAIL; ++ ++ ret = bcmnand_reg_read(ctrl, NANDC_INT_STAT_FLASH_STATUS); ++ ++ return ret; ++} ++ ++/* ++ * NAND Interface - read_oob ++ */ ++static int bcmnand_read_oob(struct mtd_info *mtd, struct nand_chip *chip, ++ int page) ++{ ++ struct bcmnand_ctrl *ctrl = chip->priv; ++ unsigned int n = ctrl->chip_num; ++ void __iomem *ctrl_spare; ++ unsigned int spare_per_sec, sector; ++ u64 nand_addr; ++ ++ ctrl_spare = ctrl->core->io_addr + NANDC_SPARE_AREA_READ_OFF; ++ ++ /* Set the page address for the following commands */ ++ nand_addr = ((u64)page << chip->page_shift); ++ bcmnand_reg_write(ctrl, NANDC_CMD_EXT_ADDR, nand_addr >> 32); ++ ++ spare_per_sec = mtd->oobsize >> ctrl->sec_per_page_shift; ++ ++ /* Disable ECC validation for spare area reads */ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_RD_ECC(n), 0); ++ ++ /* Loop all sectors in page */ ++ for (sector = 0; sector < (1<sec_per_page_shift); sector++) { ++ unsigned int col; ++ ++ col = (sector << ctrl->sector_size_shift); ++ ++ /* Issue command to read partial page */ ++ bcmnand_reg_write(ctrl, NANDC_CMD_ADDRESS, nand_addr + col); ++ ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_SPARE_READ); ++ ++ /* Wait for the command to complete */ ++ if (bcmnand_wait_cmd(ctrl, (sector == 0) ? 10000 : 100)) ++ return -EIO; ++ ++ if (!bcmnand_reg_read(ctrl, NANDC_INT_STAT_SPARE_VALID)) ++ return -EIO; ++ ++ /* Set controller to Little Endian mode for copying */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 1); ++ ++ memcpy(chip->oob_poi + sector * spare_per_sec, ++ ctrl_spare, ++ spare_per_sec); ++ ++ /* Return to Big Endian mode for commands etc */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 0); ++ } ++ ++ return 0; ++} ++ ++/* ++ * NAND Interface - write_oob ++ */ ++static int bcmnand_write_oob(struct mtd_info *mtd, struct nand_chip *chip, ++ int page) ++{ ++ struct bcmnand_ctrl *ctrl = chip->priv; ++ unsigned int n = ctrl->chip_num; ++ void __iomem *ctrl_spare; ++ unsigned int spare_per_sec, sector, num_sec; ++ u64 nand_addr; ++ int to, status = 0; ++ ++ ctrl_spare = ctrl->core->io_addr + NANDC_SPARE_AREA_WRITE_OFF; ++ ++ /* Disable ECC generation for spare area writes */ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_WR_ECC(n), 0); ++ ++ spare_per_sec = mtd->oobsize >> ctrl->sec_per_page_shift; ++ ++ /* Set the page address for the following commands */ ++ nand_addr = ((u64)page << chip->page_shift); ++ bcmnand_reg_write(ctrl, NANDC_CMD_EXT_ADDR, nand_addr >> 32); ++ ++ /* Must allow partial programming to change spare area only */ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_PGM_PARTIAL(n), 1); ++ ++ num_sec = 1 << ctrl->sec_per_page_shift; ++ /* Loop all sectors in page */ ++ for (sector = 0; sector < num_sec; sector++) { ++ unsigned int col; ++ ++ /* Spare area accessed by the data sector offset */ ++ col = (sector << ctrl->sector_size_shift); ++ ++ bcmnand_reg_write(ctrl, NANDC_CMD_ADDRESS, nand_addr + col); ++ ++ /* Set controller to Little Endian mode for copying */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 1); ++ ++ memcpy(ctrl_spare, ++ chip->oob_poi + sector * spare_per_sec, ++ spare_per_sec); ++ ++ /* Return to Big Endian mode for commands etc */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 0); ++ ++ /* Push spare bytes into internal buffer, last goes to flash */ ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_SPARE_PROG); ++ ++ if (sector == (num_sec - 1)) ++ to = 1 << 16; ++ else ++ to = 1 << 10; ++ ++ if (bcmnand_wait_cmd(ctrl, to)) ++ return -EIO; ++ } ++ ++ /* Restore partial programming inhibition */ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_PGM_PARTIAL(n), 0); ++ ++ status = bcmnand_waitfunc(mtd, chip); ++ return status & NAND_STATUS_FAIL ? -EIO : 0; ++} ++ ++/* ++ * verify that a buffer is all erased ++ */ ++static bool bcmnand_buf_erased(const void *buf, unsigned int len) ++{ ++ unsigned int i; ++ const u32 *p = buf; ++ ++ for (i = 0; i < (len >> 2); i++) { ++ if (p[i] != 0xffffffff) ++ return false; ++ } ++ return true; ++} ++ ++/* ++ * read a page, with or without ECC checking ++ */ ++static int bcmnand_read_page_do(struct mtd_info *mtd, struct nand_chip *chip, ++ uint8_t *buf, int page, bool ecc) ++{ ++ struct bcmnand_ctrl *ctrl = chip->priv; ++ unsigned int n = ctrl->chip_num; ++ void __iomem *ctrl_cache; ++ void __iomem *ctrl_spare; ++ unsigned int data_bytes; ++ unsigned int spare_per_sec; ++ unsigned int sector, to = 1 << 16; ++ u32 err_soft_reg, err_hard_reg; ++ unsigned int hard_err_count = 0; ++ int ret; ++ u64 nand_addr; ++ ++ ctrl_cache = ctrl->core->io_addr + NANDC_CACHE_OFF; ++ ctrl_spare = ctrl->core->io_addr + NANDC_SPARE_AREA_READ_OFF; ++ ++ /* Reset ECC error stats */ ++ err_hard_reg = bcmnand_reg_read(ctrl, NANDC_UNCORR_ERR_COUNT); ++ err_soft_reg = bcmnand_reg_read(ctrl, NANDC_READ_CORR_BIT_COUNT); ++ ++ spare_per_sec = mtd->oobsize >> ctrl->sec_per_page_shift; ++ ++ /* Set the page address for the following commands */ ++ nand_addr = ((u64)page << chip->page_shift); ++ bcmnand_reg_write(ctrl, NANDC_CMD_EXT_ADDR, nand_addr >> 32); ++ ++ /* Enable ECC validation for ecc page reads */ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_RD_ECC(n), ecc); ++ ++ /* Loop all sectors in page */ ++ for (sector = 0; sector < (1 << ctrl->sec_per_page_shift); sector++) { ++ data_bytes = 0; ++ ++ /* Copy partial sectors sized by cache reg */ ++ while (data_bytes < (1<sector_size_shift)) { ++ unsigned int col; ++ ++ col = data_bytes + (sector << ctrl->sector_size_shift); ++ ++ bcmnand_reg_write(ctrl, NANDC_CMD_ADDRESS, ++ nand_addr + col); ++ ++ /* Issue command to read partial page */ ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_PAGE_READ); ++ ++ /* Wait for the command to complete */ ++ ret = bcmnand_wait_cmd(ctrl, to); ++ if (ret < 0) ++ return ret; ++ ++ /* Set controller to Little Endian mode for copying */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 1); ++ ++ if (data_bytes == 0) { ++ memcpy(chip->oob_poi + sector * spare_per_sec, ++ ctrl_spare, spare_per_sec); ++ } ++ ++ memcpy(buf + col, ctrl_cache, NANDC_CACHE_SIZE); ++ data_bytes += NANDC_CACHE_SIZE; ++ ++ /* Return to Big Endian mode for commands etc */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 0); ++ ++ /* Next iterations should go fast */ ++ to = 1 << 10; ++ ++ /* capture hard errors for each partial */ ++ if (err_hard_reg != bcmnand_reg_read(ctrl, NANDC_UNCORR_ERR_COUNT)) { ++ int era = bcmnand_reg_read(ctrl, NANDC_INT_STAT_ERASED); ++ ++ if (!era && ++ !bcmnand_buf_erased(buf + col, NANDC_CACHE_SIZE)) ++ hard_err_count++; ++ ++ err_hard_reg = bcmnand_reg_read(ctrl, ++ NANDC_UNCORR_ERR_COUNT); ++ } ++ } ++ } ++ ++ if (!ecc) ++ return 0; ++ ++ /* Report hard ECC errors */ ++ if (hard_err_count) ++ mtd->ecc_stats.failed++; ++ ++ /* Get ECC soft error stats */ ++ mtd->ecc_stats.corrected += err_soft_reg - ++ bcmnand_reg_read(ctrl, NANDC_READ_CORR_BIT_COUNT); ++ ++ return 0; ++} ++ ++/* ++ * NAND Interface - read_page_ecc ++ */ ++static int bcmnand_read_page_ecc(struct mtd_info *mtd, struct nand_chip *chip, ++ uint8_t *buf, int oob_required, int page) ++{ ++ return bcmnand_read_page_do(mtd, chip, buf, page, true); ++} ++ ++/* ++ * NAND Interface - read_page_raw ++ */ ++static int bcmnand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, ++ uint8_t *buf, int oob_required, int page) ++{ ++ return bcmnand_read_page_do(mtd, chip, buf, page, true); ++} ++ ++/* ++ * do page write, with or without ECC generation enabled ++ */ ++static int bcmnand_write_page_do(struct mtd_info *mtd, struct nand_chip *chip, ++ const uint8_t *buf, bool ecc) ++{ ++ struct bcmnand_ctrl *ctrl = chip->priv; ++ unsigned int n = ctrl->chip_num; ++ void __iomem *ctrl_cache; ++ void __iomem *ctrl_spare; ++ unsigned int spare_per_sec, sector, num_sec; ++ unsigned int data_bytes, spare_bytes; ++ int i, to; ++ uint8_t *tmp_poi; ++ u32 nand_addr; ++ ++ ctrl_cache = ctrl->core->io_addr + NANDC_CACHE_OFF; ++ ctrl_spare = ctrl->core->io_addr + NANDC_SPARE_AREA_WRITE_OFF; ++ ++ /* Get start-of-page address */ ++ nand_addr = bcmnand_reg_read(ctrl, NANDC_CMD_ADDRESS); ++ ++ tmp_poi = kmalloc(mtd->oobsize, GFP_KERNEL); ++ if (!tmp_poi) ++ return -ENOMEM; ++ ++ /* Retreive pre-existing OOB values */ ++ memcpy(tmp_poi, chip->oob_poi, mtd->oobsize); ++ ctrl->cmd_ret = bcmnand_read_oob(mtd, chip, ++ nand_addr >> chip->page_shift); ++ if (ctrl->cmd_ret < 0) { ++ kfree(tmp_poi); ++ return ctrl->cmd_ret; ++ } ++ ++ /* Apply new OOB data bytes just like they would end up on the chip */ ++ for (i = 0; i < mtd->oobsize; i++) ++ chip->oob_poi[i] &= tmp_poi[i]; ++ kfree(tmp_poi); ++ ++ spare_per_sec = mtd->oobsize >> ctrl->sec_per_page_shift; ++ ++ /* Enable ECC generation for ecc page write, if requested */ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_WR_ECC(n), ecc); ++ ++ spare_bytes = 0; ++ num_sec = 1 << ctrl->sec_per_page_shift; ++ ++ /* Loop all sectors in page */ ++ for (sector = 0; sector < num_sec; sector++) { ++ data_bytes = 0; ++ ++ /* Copy partial sectors sized by cache reg */ ++ while (data_bytes < (1<sector_size_shift)) { ++ unsigned int col; ++ ++ col = data_bytes + ++ (sector << ctrl->sector_size_shift); ++ ++ /* Set address of 512-byte sub-page */ ++ bcmnand_reg_write(ctrl, NANDC_CMD_ADDRESS, ++ nand_addr + col); ++ ++ /* Set controller to Little Endian mode for copying */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, ++ 1); ++ ++ /* Set spare area is written at each sector start */ ++ if (data_bytes == 0) { ++ memcpy(ctrl_spare, ++ chip->oob_poi + spare_bytes, ++ spare_per_sec); ++ spare_bytes += spare_per_sec; ++ } ++ ++ /* Copy sub-page data */ ++ memcpy(ctrl_cache, buf + col, NANDC_CACHE_SIZE); ++ data_bytes += NANDC_CACHE_SIZE; ++ ++ /* Return to Big Endian mode for commands etc */ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 0); ++ ++ /* Push data into internal cache */ ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_PAGE_PROG); ++ ++ /* Wait for the command to complete */ ++ if (sector == (num_sec - 1)) ++ to = 1 << 16; ++ else ++ to = 1 << 10; ++ ctrl->cmd_ret = bcmnand_wait_cmd(ctrl, to); ++ if (ctrl->cmd_ret < 0) ++ return ctrl->cmd_ret; ++ } ++ } ++ return 0; ++} ++ ++/* ++ * NAND Interface = write_page_ecc ++ */ ++static int bcmnand_write_page_ecc(struct mtd_info *mtd, struct nand_chip *chip, ++ const uint8_t *buf, int oob_required) ++{ ++ return bcmnand_write_page_do(mtd, chip, buf, true); ++} ++ ++/* ++ * NAND Interface = write_page_raw ++ */ ++static int bcmnand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, ++ const uint8_t *buf, int oob_required) ++{ ++ return bcmnand_write_page_do(mtd, chip, buf, false); ++} ++ ++/* ++ * MTD Interface - read_byte ++ * ++ * This function emulates simple controllers behavior ++ * for just a few relevant commands ++ */ ++static uint8_t bcmnand_read_byte(struct mtd_info *mtd) ++{ ++ struct nand_chip *nand = mtd->priv; ++ struct bcmnand_ctrl *ctrl = nand->priv; ++ uint8_t b = ~0; ++ ++ switch (ctrl->last_cmd) { ++ case NAND_CMD_READID: ++ if (ctrl->id_byte_index < 8) { ++ b = bcmnand_reg_read(ctrl, NANDC_DEVID_BYTE( ++ ctrl->id_byte_index)); ++ ctrl->id_byte_index++; ++ } ++ break; ++ case NAND_CMD_READOOB: ++ if (ctrl->oob_index < mtd->oobsize) ++ b = nand->oob_poi[ctrl->oob_index++]; ++ break; ++ case NAND_CMD_STATUS: ++ b = bcmnand_reg_read(ctrl, NANDC_INT_STAT_FLASH_STATUS); ++ break; ++ default: ++ pr_err("%s: got unkown command: 0x%x in %s\n", DRV_NAME, ++ ctrl->last_cmd, __func__); ++ } ++ return b; ++} ++ ++/* ++ * MTD Interface - read_word ++ * ++ * Can not be tested without x16 chip, but the SoC does not support x16 i/f. ++ */ ++static u16 bcmnand_read_word(struct mtd_info *mtd) ++{ ++ u16 w = ~0; ++ ++ w = bcmnand_read_byte(mtd); ++ barrier(); ++ w |= bcmnand_read_byte(mtd) << 8; ++ ++ return w; ++} ++ ++/* ++ * MTD Interface - select a chip from an array ++ */ ++static void bcmnand_select_chip(struct mtd_info *mtd, int chip) ++{ ++ struct nand_chip *nand = mtd->priv; ++ struct bcmnand_ctrl *ctrl = nand->priv; ++ ++ ctrl->chip_num = chip; ++ bcmnand_reg_write(ctrl, NANDC_CMD_CS_SEL, chip); ++} ++ ++/* ++ * NAND Interface - emulate low-level NAND commands ++ * ++ * Only a few low-level commands are really needed by generic NAND, ++ * and they do not call for CMD_LL operations the controller can support. ++ */ ++static void bcmnand_cmdfunc(struct mtd_info *mtd, unsigned int command, ++ int column, int page_addr) ++{ ++ struct nand_chip *nand = mtd->priv; ++ struct bcmnand_ctrl *ctrl = nand->priv; ++ u64 nand_addr; ++ unsigned int to = 1; ++ ++ ctrl->last_cmd = command; ++ ++ /* Set address for some commands */ ++ switch (command) { ++ case NAND_CMD_ERASE1: ++ column = 0; ++ /*FALLTHROUGH*/ ++ case NAND_CMD_SEQIN: ++ case NAND_CMD_READ0: ++ case NAND_CMD_READ1: ++ WARN_ON(column >= mtd->writesize); ++ nand_addr = (u64) column | ++ ((u64)page_addr << nand->page_shift); ++ bcmnand_reg_write(ctrl, NANDC_CMD_EXT_ADDR, nand_addr >> 32); ++ bcmnand_reg_write(ctrl, NANDC_CMD_ADDRESS, nand_addr); ++ break; ++ case NAND_CMD_ERASE2: ++ case NAND_CMD_RESET: ++ case NAND_CMD_READID: ++ case NAND_CMD_READOOB: ++ case NAND_CMD_PAGEPROG: ++ default: ++ /* Do nothing, address not used */ ++ break; ++ } ++ ++ /* Issue appropriate command to controller */ ++ switch (command) { ++ case NAND_CMD_SEQIN: ++ /* Only need to load command address, done */ ++ return; ++ ++ case NAND_CMD_RESET: ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_FLASH_RESET); ++ to = 1 << 8; ++ break; ++ ++ case NAND_CMD_READID: ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_DEVID_READ); ++ ctrl->id_byte_index = 0; ++ to = 1 << 8; ++ break; ++ ++ case NAND_CMD_READ0: ++ case NAND_CMD_READ1: ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_PAGE_READ); ++ to = 1 << 15; ++ break; ++ case NAND_CMD_STATUS: ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_STATUS_READ); ++ to = 1 << 8; ++ break; ++ case NAND_CMD_ERASE1: ++ return; ++ ++ case NAND_CMD_ERASE2: ++ bcmnand_reg_write(ctrl, NANDC_CMD_START_OPCODE, ++ NANDC_CMD_OPCODE_BLOCK_ERASE); ++ to = 1 << 18; ++ break; ++ ++ case NAND_CMD_PAGEPROG: ++ /* Cmd already set from write_page */ ++ return; ++ ++ case NAND_CMD_READOOB: ++ /* Emulate simple interface */ ++ bcmnand_read_oob(mtd, nand, page_addr); ++ ctrl->oob_index = 0; ++ return; ++ ++ default: ++ pr_err("%s: got unkown command: 0x%x in %s\n", DRV_NAME, ++ ctrl->last_cmd, __func__); ++ } ++ ++ /* Wait for command to complete */ ++ ctrl->cmd_ret = bcmnand_wait_cmd(ctrl, to); ++ ++} ++ ++static int bcmnand_scan(struct mtd_info *mtd) ++{ ++ struct nand_chip *nand = mtd->priv; ++ struct bcmnand_ctrl *ctrl = nand->priv; ++ bool sector_1k = false; ++ unsigned int chip_num = 0; ++ int ecc_level = 0; ++ int ret; ++ ++ ret = nand_scan_ident(mtd, NANDC_MAX_CHIPS, NULL); ++ if (ret) ++ return ret; ++ ++ /* Get configuration from first chip */ ++ sector_1k = bcmnand_reg_read(ctrl, NANDC_ACC_CTRL_SECTOR_1K(0)); ++ ecc_level = bcmnand_reg_read(ctrl, NANDC_ACC_CTRL_ECC_LEVEL(0)); ++ mtd->writesize_shift = nand->page_shift; ++ ++ ctrl->ecc_level = ecc_level; ++ ctrl->sector_size_shift = sector_1k ? 10 : 9; ++ ++ /* Configure spare area, tweak as needed */ ++ do { ++ ctrl->sec_per_page_shift = ++ mtd->writesize_shift - ctrl->sector_size_shift; ++ ++ /* will return -EINVAL if OOB space exhausted */ ++ ret = bcmnand_hw_ecc_layout(ctrl); ++ ++ /* First try to bump sector size to 1k, then decrease level */ ++ if (ret && nand->page_shift > 9 && ctrl->sector_size_shift < 10) ++ ctrl->sector_size_shift = 10; ++ else if (ret) ++ ctrl->ecc_level--; ++ ++ } while (ret && ctrl->ecc_level > 0); ++ ++ if (WARN_ON(ctrl->ecc_level == 0)) ++ return -ENOENT; ++ ++ if ((ctrl->sector_size_shift > 9) != (sector_1k == 1)) { ++ pr_info("%s: sector size adjusted to 1k\n", DRV_NAME); ++ sector_1k = 1; ++ } ++ ++ if (ecc_level != ctrl->ecc_level) { ++ pr_info("%s: ECC level adjusted from %u to %u\n", ++ DRV_NAME, ecc_level, ctrl->ecc_level); ++ ecc_level = ctrl->ecc_level; ++ } ++ ++ /* handle the hardware chip config registers */ ++ for (chip_num = 0; chip_num < nand->numchips; chip_num++) { ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_SECTOR_1K(chip_num), ++ sector_1k); ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_ECC_LEVEL(chip_num), ++ ecc_level); ++ ++ /* Large pages: no partial page programming */ ++ if (mtd->writesize > 512) { ++ bcmnand_reg_write(ctrl, ++ NANDC_ACC_CTRL_PGM_RDIN(chip_num), 0); ++ bcmnand_reg_write(ctrl, ++ NANDC_ACC_CTRL_PGM_PARTIAL(chip_num), 0); ++ } ++ ++ /* Do not raise ECC error when reading erased pages */ ++ /* This bit has only partial effect, driver needs to help */ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_ERA_ECC_ERR(chip_num), ++ 0); ++ ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_PG_HIT(chip_num), 0); ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_PREFETCH(chip_num), 0); ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_CACHE_MODE(chip_num), 0); ++ bcmnand_reg_write(ctrl, NANDC_ACC_CTRL_CACHE_LASTPG(chip_num), ++ 0); ++ ++ /* TBD: consolidate or at least verify the s/w and h/w geometries agree */ ++ } ++ ++ /* Allow writing on device */ ++ if (!(nand->options & NAND_ROM)) ++ bcmnand_reg_write(ctrl, NANDC_CS_NAND_WP, 0); ++ ++ pr_debug("%s: layout.oobavail=%d\n", DRV_NAME, ++ nand->ecc.layout->oobavail); ++ ++ ret = nand_scan_tail(mtd); ++ ++ if (nand->badblockbits == 0) ++ nand->badblockbits = 8; ++ if (WARN_ON((1 << nand->page_shift) != mtd->writesize)) ++ return -EIO; ++ ++ /* Spit out some key chip parameters as detected by nand_base */ ++ pr_debug("%s: erasesize=%d writesize=%d oobsize=%d page_shift=%d badblockpos=%d badblockbits=%d\n", ++ DRV_NAME, mtd->erasesize, mtd->writesize, mtd->oobsize, ++ nand->page_shift, nand->badblockpos, nand->badblockbits); ++ ++ return ret; ++} ++ ++/* ++ * main intiailization function ++ */ ++static int bcmnand_ctrl_init(struct bcmnand_ctrl *ctrl) ++{ ++ unsigned int chip; ++ struct nand_chip *nand; ++ struct mtd_info *mtd; ++ unsigned int n = 0; ++ int ret; ++ ++ /* Software variables init */ ++ nand = &ctrl->nand; ++ mtd = &ctrl->mtd; ++ ++ init_completion(&ctrl->op_completion); ++ ++ mtd->priv = nand; ++ mtd->owner = THIS_MODULE; ++ mtd->name = DRV_NAME; ++ ++ nand->priv = ctrl; ++ ++ nand->chip_delay = 5; /* not used */ ++ nand->IO_ADDR_R = nand->IO_ADDR_W = (void *)~0L; ++ ++ if (bcmnand_reg_read(ctrl, NANDC_CONFIG_CHIP_WIDTH(n))) ++ nand->options |= NAND_BUSWIDTH_16; ++ nand->options |= NAND_SKIP_BBTSCAN; /* Dont need BBTs */ ++ ++ nand->options |= NAND_NO_SUBPAGE_WRITE; /* Subpages unsupported */ ++ ++ nand->dev_ready = bcmnand_dev_ready; ++ nand->read_byte = bcmnand_read_byte; ++ nand->read_word = bcmnand_read_word; ++ nand->select_chip = bcmnand_select_chip; ++ nand->cmdfunc = bcmnand_cmdfunc; ++ nand->waitfunc = bcmnand_waitfunc; ++ ++ nand->ecc.mode = NAND_ECC_HW; ++ nand->ecc.read_page_raw = bcmnand_read_page_raw; ++ nand->ecc.write_page_raw = bcmnand_write_page_raw; ++ nand->ecc.read_page = bcmnand_read_page_ecc; ++ nand->ecc.write_page = bcmnand_write_page_ecc; ++ nand->ecc.read_oob = bcmnand_read_oob; ++ nand->ecc.write_oob = bcmnand_write_oob; ++ ++ /* Set AUTO_CNFIG bit - try to auto-detect chips */ ++ bcmnand_reg_write(ctrl, NANDC_CS_AUTO_CONFIG, 1); ++ ++ usleep_range(1000, 1500); ++ ++ /* Print out current chip config */ ++ for (chip = 0; chip < NANDC_MAX_CHIPS; chip++) { ++ pr_debug("%s: chip[%d]: size=%#x block=%#x page=%#x ecc_level=%#x\n", ++ DRV_NAME, chip, ++ bcmnand_reg_read(ctrl, NANDC_CONFIG_CHIP_SIZE(chip)), ++ bcmnand_reg_read(ctrl, NANDC_CONFIG_BLK_SIZE(chip)), ++ bcmnand_reg_read(ctrl, NANDC_CONFIG_PAGE_SIZE(chip)), ++ bcmnand_reg_read(ctrl, NANDC_ACC_CTRL_ECC_LEVEL(chip))); ++ } ++ ++ pr_debug("%s: Nand controller is reads=%d\n", DRV_NAME, ++ bcmnand_reg_aread(ctrl, NANDC_IDM_IO_CTRL_RDY)); ++ ++ ret = bcmnand_scan(mtd); ++ if (ret) { ++ pr_err("%s: scanning the nand flash chip failed with %i\n", ++ DRV_NAME, ret); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int __init bcmnand_idm_init(struct bcmnand_ctrl *ctrl) ++{ ++ int irq_off; ++ unsigned int retries = 0x1000; ++ ++ if (bcmnand_reg_aread(ctrl, NANDC_IDM_RESET)) ++ pr_err("%s: stuck in reset\n", DRV_NAME); ++ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_RESET, 1); ++ if (!bcmnand_reg_aread(ctrl, NANDC_IDM_RESET)) { ++ pr_err("%s: reset of failed\n", DRV_NAME); ++ return -EIO; ++ } ++ ++ while (bcmnand_reg_aread(ctrl, NANDC_IDM_RESET)) { ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_RESET, 0); ++ cpu_relax(); ++ usleep_range(100, 150); ++ if (!(retries--)) { ++ pr_err("%s: did not came back from reset\n", ++ DRV_NAME); ++ return -ETIMEDOUT; ++ } ++ } ++ ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_CLOCK_EN, 1); ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_APB_LITTLE_ENDIAN, 0); ++ udelay(10); ++ ++ pr_info("%s: NAND Controller rev %d.%d\n", DRV_NAME, ++ bcmnand_reg_read(ctrl, NANDC_REV_MAJOR), ++ bcmnand_reg_read(ctrl, NANDC_REV_MINOR)); ++ ++ usleep_range(250, 350); ++ ++ /* Disable all IRQs */ ++ for (irq_off = 0; irq_off < NANDC_IRQ_NUM; irq_off++) ++ bcmnand_reg_awrite(ctrl, NANDC_IDM_IRQ_N_EN(irq_off), 0); ++ ++ return 0; ++} ++ ++static const char * const part_probes[] = { "bcm47xxpart", "cmdlinepart", NULL }; ++ ++/* ++ * Top-level init function ++ */ ++static int bcmnand_probe(struct bcma_device *core) ++{ ++ struct device *dev = &core->dev; ++ struct device_node *np = dev->of_node; ++ struct bcmnand_ctrl *ctrl; ++ int res, i, irq; ++ ++ if (!np) { ++ pr_err("%s: no device tree node found\n", DRV_NAME); ++ return -ENOENT; ++ } ++ ++ ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL); ++ if (!ctrl) ++ return -ENOMEM; ++ ++ bcma_set_drvdata(core, ctrl); ++ ++ ctrl->mtd.dev.parent = &core->dev; ++ ctrl->core = core; ++ ++ /* Acquire all interrupt lines */ ++ for (i = 0; i < of_irq_count(np); i++) { ++ irq = irq_of_parse_and_map(np, i); ++ res = devm_request_irq(dev, irq, bcmnand_isr, 0, DRV_NAME, ctrl); ++ if (res < 0) { ++ pr_err("%s: problem requesting irq: %i (idx: %i)\n", ++ DRV_NAME, irq, i); ++ return res; ++ } ++ } ++ ++ res = bcmnand_idm_init(ctrl); ++ if (res) ++ return res; ++ ++ res = bcmnand_ctrl_init(ctrl); ++ if (res) ++ return res; ++ ++ res = mtd_device_parse_register(&ctrl->mtd, part_probes, NULL, NULL, 0); ++ if (res) { ++ pr_err("%s: Failed to register MTD device: %d\n", DRV_NAME, res); ++ return res; ++ } ++ return 0; ++} ++ ++static void bcmnand_remove(struct bcma_device *core) ++{ ++ struct bcmnand_ctrl *ctrl = bcma_get_drvdata(core); ++ ++ mtd_device_unregister(&ctrl->mtd); ++} ++ ++static const struct bcma_device_id bcmnand_bcma_tbl[] = { ++ BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_NAND, BCMA_ANY_REV, BCMA_ANY_CLASS), ++ BCMA_CORETABLE_END ++}; ++MODULE_DEVICE_TABLE(bcma, bgmac_bcma_tbl); ++ ++static struct bcma_driver bcmnand_bcma_driver = { ++ .name = KBUILD_MODNAME, ++ .id_table = bcmnand_bcma_tbl, ++ .probe = bcmnand_probe, ++ .remove = bcmnand_remove, ++}; ++ ++static int __init bcmnand_init(void) ++{ ++ int err; ++ ++ err = bcma_driver_register(&bcmnand_bcma_driver); ++ if (err) ++ return err; ++ pr_info("%s: Broadcom NAND Controller driver loaded\n", DRV_NAME); ++ ++ return 0; ++} ++ ++static void __exit bcmnand_exit(void) ++{ ++ bcma_driver_unregister(&bcmnand_bcma_driver); ++} ++ ++module_init(bcmnand_init) ++module_exit(bcmnand_exit) ++ ++MODULE_LICENSE("GPL"); ++MODULE_DESCRIPTION(DRV_DESC); -- 2.25.1