From 473c63592ea8cbcb5b57452e9857d961bb433cae Mon Sep 17 00:00:00 2001 From: Jason Liu Date: Fri, 16 Dec 2011 05:17:08 +0000 Subject: [PATCH] i.mx6q: arm2: Add the enet function support This enable the network function on the i.mx6q armadillo2 board(arm2), thus we can use tftp to load image from network. Cc: Stefano Babic Signed-off-by: Jason Liu Tested-by: Dirk Behme --- board/freescale/mx6qarm2/mx6qarm2.c | 90 +++++++++++++++++++++++++++++ include/configs/mx6qarm2.h | 12 +++- 2 files changed, 100 insertions(+), 2 deletions(-) diff --git a/board/freescale/mx6qarm2/mx6qarm2.c b/board/freescale/mx6qarm2/mx6qarm2.c index 89e0e768e5..98942454a0 100644 --- a/board/freescale/mx6qarm2/mx6qarm2.c +++ b/board/freescale/mx6qarm2/mx6qarm2.c @@ -29,6 +29,8 @@ #include #include #include +#include +#include DECLARE_GLOBAL_DATA_PTR; @@ -40,6 +42,10 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) +#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + int dram_init(void) { gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); @@ -79,11 +85,35 @@ iomux_v3_cfg_t usdhc4_pads[] = { MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), }; +iomux_v3_cfg_t enet_pads[] = { + MX6Q_PAD_KEY_COL1__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_KEY_COL2__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6Q_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), +}; + + static void setup_iomux_uart(void) { imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads)); } +static void setup_iomux_enet(void) +{ + imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); +} + #ifdef CONFIG_FSL_ESDHC struct fsl_esdhc_cfg usdhc_cfg[2] = { {USDHC3_BASE_ADDR, 1}, @@ -132,9 +162,69 @@ int board_mmc_init(bd_t *bis) } #endif +#define MII_MMD_ACCESS_CTRL_REG 0xd +#define MII_MMD_ACCESS_ADDR_DATA_REG 0xe +#define MII_DBG_PORT_REG 0x1d +#define MII_DBG_PORT2_REG 0x1e + +int fecmxc_mii_postcall(int phy) +{ + unsigned short val; + + /* + * Due to the i.MX6Q Armadillo2 board HW design,there is + * no 125Mhz clock input from SOC. In order to use RGMII, + * We need enable AR8031 ouput a 125MHz clk from CLK_25M + */ + miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x7); + miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, 0x8016); + miiphy_write("FEC", phy, MII_MMD_ACCESS_CTRL_REG, 0x4007); + miiphy_read("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, &val); + val &= 0xffe3; + val |= 0x18; + miiphy_write("FEC", phy, MII_MMD_ACCESS_ADDR_DATA_REG, val); + + /* For the RGMII phy, we need enable tx clock delay */ + miiphy_write("FEC", phy, MII_DBG_PORT_REG, 0x5); + miiphy_read("FEC", phy, MII_DBG_PORT2_REG, &val); + val |= 0x0100; + miiphy_write("FEC", phy, MII_DBG_PORT2_REG, val); + + miiphy_write("FEC", phy, MII_BMCR, 0xa100); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + struct eth_device *dev; + int ret; + + ret = cpu_eth_init(bis); + if (ret) { + printf("FEC MXC: %s:failed\n", __func__); + return ret; + } + + dev = eth_get_dev_by_name("FEC"); + if (!dev) { + printf("FEC MXC: Unable to get FEC device entry\n"); + return -EINVAL; + } + + ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall); + if (ret) { + printf("FEC MXC: Unable to register FEC mii postcall\n"); + return ret; + } + + return 0; +} + int board_early_init_f(void) { setup_iomux_uart(); + setup_iomux_enet(); return 0; } diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h index a7b363dbd4..124a7a63ae 100644 --- a/include/configs/mx6qarm2.h +++ b/include/configs/mx6qarm2.h @@ -56,6 +56,16 @@ #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_FEC_MXC_PHYADDR 0 + /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_CONS_INDEX 1 @@ -66,8 +76,6 @@ #include #undef CONFIG_CMD_IMLS -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS #define CONFIG_BOOTDELAY 3 -- 2.25.1