From 4436979c83e0d9ef4d7c3162e9d573bb521f61ff Mon Sep 17 00:00:00 2001 From: Piotr Dymacz Date: Thu, 16 Mar 2017 00:54:08 +0100 Subject: [PATCH] ar71xx: add support for P&W R602N and CPE505N P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz --- .../ar71xx/base-files/etc/board.d/01_leds | 21 +- .../ar71xx/base-files/etc/board.d/02_network | 1 + target/linux/ar71xx/base-files/etc/diag.sh | 4 + target/linux/ar71xx/base-files/lib/ar71xx.sh | 6 + .../ar71xx/base-files/lib/upgrade/platform.sh | 2 + target/linux/ar71xx/config-4.4 | 2 + .../files/arch/mips/ath79/Kconfig.openwrt | 19 ++ .../ar71xx/files/arch/mips/ath79/Makefile | 2 + .../ar71xx/files/arch/mips/ath79/mach-r602n.c | 213 ++++++++++++++++++ .../ar71xx/files/arch/mips/ath79/machtypes.h | 2 + target/linux/ar71xx/image/generic.mk | 17 ++ target/linux/ar71xx/mikrotik/config-default | 2 + target/linux/ar71xx/nand/config-default | 2 + 13 files changed, 285 insertions(+), 8 deletions(-) create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-r602n.c diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 082b6c478e..1a4b02c535 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -83,6 +83,7 @@ ap147-010) ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "ap147:green:wlan-2g" "phy0tpt" ;; ap90q|\ +cpe505n|\ cpe830|\ cpe870|\ dr531) @@ -93,6 +94,9 @@ dr531) ap90q) ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" ;; + cpe505n) + ucidef_set_led_wlan "wlan" "WLAN" "$board:blue:wlan" "phy0tpt" + ;; cpe830|\ cpe870) ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" @@ -502,6 +506,15 @@ pqi-air-pen) qihoo-c301) ucidef_set_led_wlan "wlan2g" "WLAN2G" "qihoo:red:status" "phy1tpt" ;; +r602n|\ +zbt-we1526) + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" + ucidef_set_led_switch "lan1" "LAN1" "$board:green:lan1" "switch0" "0x10" + ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08" + ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x04" + ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02" + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ;; re450) ucidef_set_led_netdev "lan_data" "LAN Data" "$board:green:lan_data" "eth0" "tx rx" ucidef_set_led_netdev "lan_link" "LAN Link" "$board:green:lan_link" "eth0" "link" @@ -846,14 +859,6 @@ xd3200) z1) ucidef_set_led_netdev "wlan1" "WLAN1" "$board:blue:tricolor0" "wlan1" ;; -zbt-we1526) - ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth1" - ucidef_set_led_switch "lan1" "LAN1" "$board:green:lan1" "switch0" "0x10" - ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08" - ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x04" - ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02" - ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" - ;; zcn-1523h-2) ucidef_set_led_netdev "lan1" "lan1" "zcn-1523h:green:lan1" "eth0" ;; diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index 08ee584480..e5892ac485 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -31,6 +31,7 @@ ar71xx_setup_interfaces() mynet-n600|\ oolite|\ qihoo-c301|\ + r602n|\ rb-750|\ rb-751|\ som9331|\ diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 00f6a7db07..fed51a17d7 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -32,6 +32,7 @@ get_status_led() { ;; ap132|\ ap531b0|\ + cpe505n|\ db120|\ dr344|\ tew-632brp|\ @@ -280,6 +281,9 @@ get_status_led() { pb44) status_led="$board:amber:jump1" ;; + r602n) + status_led="$board:green:wan" + ;; rb-2011l|\ rb-2011uas|\ rb-2011uas-2hnd) diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 267cb6ad58..eedcb7829c 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -508,6 +508,9 @@ ar71xx_board_detect() { name="cpe210" tplink_pharos_board_detect ;; + *"CPE505N") + name="cpe505n" + ;; *"CPE510/520") name="cpe510" tplink_pharos_board_detect @@ -802,6 +805,9 @@ ar71xx_board_detect() { *"Qihoo 360 C301") name="qihoo-c301" ;; + *"R602N") + name="r602n" + ;; *"R6100") name="r6100" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 38a78830a0..2f0228b823 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -217,6 +217,7 @@ platform_check_image() { cf-e380ac-v2|\ cf-e520n|\ cf-e530n|\ + cpe505n|\ cpe830|\ cpe870|\ dgl-5500-a1|\ @@ -256,6 +257,7 @@ platform_check_image() { nanostation-m|\ nbg460n_550n_550nh|\ pqi-air-pen|\ + r602n|\ rocket-m-ti|\ rocket-m-xw|\ rocket-m|\ diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4 index 09ffd8b6bf..386ce6824e 100644 --- a/target/linux/ar71xx/config-4.4 +++ b/target/linux/ar71xx/config-4.4 @@ -70,6 +70,7 @@ CONFIG_ATH79_MACH_CF_E380AC_V1=y CONFIG_ATH79_MACH_CF_E380AC_V2=y CONFIG_ATH79_MACH_CF_E520N=y CONFIG_ATH79_MACH_CF_E530N=y +CONFIG_ATH79_MACH_CPE505N=y CONFIG_ATH79_MACH_CPE510=y CONFIG_ATH79_MACH_CPE830=y CONFIG_ATH79_MACH_CPE870=y @@ -143,6 +144,7 @@ CONFIG_ATH79_MACH_PB42=y CONFIG_ATH79_MACH_PB44=y CONFIG_ATH79_MACH_PQI_AIR_PEN=y CONFIG_ATH79_MACH_QIHOO_C301=y +CONFIG_ATH79_MACH_R602N=y CONFIG_ATH79_MACH_R6100=y # CONFIG_ATH79_MACH_RB2011 is not set # CONFIG_ATH79_MACH_RB4XX is not set diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index d72c462f6e..669e02684f 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -851,6 +851,16 @@ config ATH79_MACH_WRTNODE2Q select ATH79_DEV_M25P80 select ATH79_DEV_WMAC +config ATH79_MACH_R602N + bool "P&W R602N support" + select SOC_QCA953X + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + select ATH79_DEV_USB + select ATH79_DEV_WMAC + config ATH79_MACH_R6100 bool "NETGEAR R6100 board support" select SOC_AR934X @@ -1308,6 +1318,15 @@ config ATH79_MACH_ARCHER_C7 select ATH79_DEV_USB select ATH79_DEV_WMAC +config ATH79_MACH_CPE505N + bool "P&W CPE505N support" + select SOC_QCA953X + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + select ATH79_DEV_WMAC + config ATH79_MACH_CPE510 bool "TP-LINK CPE510 support" select SOC_AR934X diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 7e1a71b34d..1180d4d73b 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -75,6 +75,7 @@ obj-$(CONFIG_ATH79_MACH_CF_E380AC_V1) += mach-cf-e316n-v2.o obj-$(CONFIG_ATH79_MACH_CF_E380AC_V2) += mach-cf-e316n-v2.o obj-$(CONFIG_ATH79_MACH_CF_E520N) += mach-cf-e316n-v2.o obj-$(CONFIG_ATH79_MACH_CF_E530N) += mach-cf-e316n-v2.o +obj-$(CONFIG_ATH79_MACH_CPE505N) += mach-r602n.o obj-$(CONFIG_ATH79_MACH_CPE510) += mach-cpe510.o obj-$(CONFIG_ATH79_MACH_CPE830) += mach-ap90q.o obj-$(CONFIG_ATH79_MACH_CPE870) += mach-cpe870.o @@ -147,6 +148,7 @@ obj-$(CONFIG_ATH79_MACH_PB42) += mach-pb42.o obj-$(CONFIG_ATH79_MACH_PB44) += mach-pb44.o obj-$(CONFIG_ATH79_MACH_PQI_AIR_PEN) += mach-pqi-air-pen.o obj-$(CONFIG_ATH79_MACH_QIHOO_C301) += mach-qihoo-c301.o +obj-$(CONFIG_ATH79_MACH_R602N) += mach-r602n.o obj-$(CONFIG_ATH79_MACH_R6100) += mach-r6100.o obj-$(CONFIG_ATH79_MACH_RB2011) += mach-rb2011.o obj-$(CONFIG_ATH79_MACH_RB4XX) += mach-rb4xx.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-r602n.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-r602n.c new file mode 100644 index 0000000000..4aef0a932a --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-r602n.c @@ -0,0 +1,213 @@ +/* + * P&W (Shenzhen Progress&Win Technologies) R602N and CPE505N boards support + * + * Copyright (C) 2017 Piotr Dymacz + * + * Based on mach-zbt-we1526.c + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include +#include + +#include +#include + +#include "common.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-m25p80.h" +#include "dev-usb.h" +#include "dev-wmac.h" +#include "machtypes.h" + +#define PW_GPIO_BTN_RESET 17 + +#define PW_KEYS_POLL_INTERVAL 20 /* msecs */ +#define PW_KEYS_DEBOUNCE_INTERVAL (3 * PW_KEYS_POLL_INTERVAL) + +#define PW_MAC0_OFFSET 0x0 +#define PW_MAC1_OFFSET 0x6 +#define PW_WMAC_CALDATA_OFFSET 0x1000 + +/* CPE505N GPIO LEDs */ +#define CPE505N_GPIO_LED_DIAG 12 +#define CPE505N_GPIO_LED_LAN 11 +#define CPE505N_GPIO_LED_STATUS 14 +#define CPE505N_GPIO_LED_WAN 4 +#define CPE505N_GPIO_LED_WLAN 15 + +static struct gpio_led cpe505n_leds_gpio[] __initdata = { + { + .name = "cpe505n:red:diag", + .gpio = CPE505N_GPIO_LED_DIAG, + .active_low = 1, + }, { + .name = "cpe505n:green:lan", + .gpio = CPE505N_GPIO_LED_LAN, + .active_low = 1, + }, { + .name = "cpe505n:green:status", + .gpio = CPE505N_GPIO_LED_STATUS, + .active_low = 1, + }, { + .name = "cpe505n:green:wan", + .gpio = CPE505N_GPIO_LED_WAN, + .active_low = 1, + }, { + .name = "cpe505n:blue:wlan", + .gpio = CPE505N_GPIO_LED_WLAN, + .active_low = 1, + }, +}; + +static void __init cpe505n_gpio_setup(void) +{ + /* For LED on GPIO4 */ + ath79_gpio_function_disable(AR934X_GPIO_FUNC_CLK_OBS4_EN); + ath79_gpio_output_select(CPE505N_GPIO_LED_WAN, 0); + + ath79_gpio_direction_select(CPE505N_GPIO_LED_DIAG, true); + ath79_gpio_direction_select(CPE505N_GPIO_LED_LAN, true); + ath79_gpio_direction_select(CPE505N_GPIO_LED_STATUS, true); + ath79_gpio_direction_select(CPE505N_GPIO_LED_WAN, true); + ath79_gpio_direction_select(CPE505N_GPIO_LED_WLAN, true); + + /* Mute LEDs */ + gpio_set_value(CPE505N_GPIO_LED_DIAG, 1); + gpio_set_value(CPE505N_GPIO_LED_LAN, 1); + gpio_set_value(CPE505N_GPIO_LED_STATUS, 1); + gpio_set_value(CPE505N_GPIO_LED_WAN, 1); + gpio_set_value(CPE505N_GPIO_LED_WLAN, 1); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(cpe505n_leds_gpio), + cpe505n_leds_gpio); +} + +/* R602N GPIO LEDs */ +#define R602N_GPIO_LED_LAN1 16 +#define R602N_GPIO_LED_LAN2 15 +#define R602N_GPIO_LED_LAN3 14 +#define R602N_GPIO_LED_LAN4 11 +#define R602N_GPIO_LED_WAN 4 +#define R602N_GPIO_LED_WLAN 12 + +static struct gpio_led r602n_leds_gpio[] __initdata = { + { + .name = "r602n:green:lan1", + .gpio = R602N_GPIO_LED_LAN1, + .active_low = 1, + }, { + .name = "r602n:green:lan2", + .gpio = R602N_GPIO_LED_LAN2, + .active_low = 1, + }, { + .name = "r602n:green:lan3", + .gpio = R602N_GPIO_LED_LAN3, + .active_low = 1, + }, { + .name = "r602n:green:lan4", + .gpio = R602N_GPIO_LED_LAN4, + .active_low = 1, + }, { + .name = "r602n:green:wan", + .gpio = R602N_GPIO_LED_WAN, + .active_low = 1, + }, { + .name = "r602n:green:wlan", + .gpio = R602N_GPIO_LED_WLAN, + .active_low = 1, + }, +}; + +static void __init r602n_gpio_setup(void) +{ + /* For LED on GPIO4 */ + ath79_gpio_function_disable(AR934X_GPIO_FUNC_CLK_OBS4_EN); + ath79_gpio_output_select(R602N_GPIO_LED_WAN, 0); + + ath79_gpio_direction_select(R602N_GPIO_LED_LAN1, true); + ath79_gpio_direction_select(R602N_GPIO_LED_LAN2, true); + ath79_gpio_direction_select(R602N_GPIO_LED_LAN3, true); + ath79_gpio_direction_select(R602N_GPIO_LED_LAN4, true); + ath79_gpio_direction_select(R602N_GPIO_LED_WAN, true); + ath79_gpio_direction_select(R602N_GPIO_LED_WLAN, true); + + /* Mute LEDs */ + gpio_set_value(R602N_GPIO_LED_LAN1, 1); + gpio_set_value(R602N_GPIO_LED_LAN2, 1); + gpio_set_value(R602N_GPIO_LED_LAN3, 1); + gpio_set_value(R602N_GPIO_LED_LAN4, 1); + gpio_set_value(R602N_GPIO_LED_WAN, 1); + gpio_set_value(R602N_GPIO_LED_WLAN, 1); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(r602n_leds_gpio), + r602n_leds_gpio); +} + +static struct gpio_keys_button pw_gpio_keys[] __initdata = { + { + .desc = "reset", + .type = EV_KEY, + .code = KEY_RESTART, + .debounce_interval = PW_KEYS_DEBOUNCE_INTERVAL, + .gpio = PW_GPIO_BTN_RESET, + .active_low = 1, + }, +}; + +static void __init r602n_cpe505n_setup(void) +{ + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + + ath79_register_m25p80(NULL); + + ath79_setup_ar933x_phy4_switch(false, false); + + ath79_register_mdio(0, 0x0); + + /* LAN */ + ath79_eth1_data.duplex = DUPLEX_FULL; + ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII; + ath79_switch_data.phy_poll_mask |= BIT(4); + ath79_init_mac(ath79_eth1_data.mac_addr, art + PW_MAC1_OFFSET, 0); + ath79_register_eth(1); + + /* WAN */ + ath79_switch_data.phy4_mii_en = 1; + ath79_eth0_data.duplex = DUPLEX_FULL; + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII; + ath79_eth0_data.phy_mask = BIT(4); + ath79_eth0_data.speed = SPEED_100; + ath79_init_mac(ath79_eth0_data.mac_addr, art + PW_MAC0_OFFSET, 0); + ath79_register_eth(0); + + ath79_register_wmac(art + PW_WMAC_CALDATA_OFFSET, NULL); + + ath79_register_gpio_keys_polled(-1, PW_KEYS_POLL_INTERVAL, + ARRAY_SIZE(pw_gpio_keys), + pw_gpio_keys); +} + +static void __init cpe505n_setup(void) +{ + r602n_cpe505n_setup(); + + cpe505n_gpio_setup(); +} + +static void __init r602n_setup(void) +{ + r602n_cpe505n_setup(); + + r602n_gpio_setup(); + + ath79_register_usb(); +} + +MIPS_MACHINE(ATH79_MACH_CPE505N, "CPE505N", "P&W CPE505N", cpe505n_setup); +MIPS_MACHINE(ATH79_MACH_R602N, "R602N", "P&W R602N", r602n_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index 27ebd47f29..b9cc243f39 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -62,6 +62,7 @@ enum ath79_mach_type { ATH79_MACH_CF_E520N, /* COMFAST CF-E520N */ ATH79_MACH_CF_E530N, /* COMFAST CF-E530N */ ATH79_MACH_CPE210, /* TP-LINK CPE210 */ + ATH79_MACH_CPE505N, /* P&W CPE505N */ ATH79_MACH_CPE510, /* TP-LINK CPE510 */ ATH79_MACH_CPE830, /* YunCore CPE830 */ ATH79_MACH_CPE870, /* YunCore CPE870 */ @@ -152,6 +153,7 @@ enum ath79_mach_type { ATH79_MACH_PB44, /* Atheros PB44 reference board */ ATH79_MACH_PQI_AIR_PEN, /* PQI Air Pen */ ATH79_MACH_QIHOO_C301, /* Qihoo 360 C301 */ + ATH79_MACH_R602N, /* P&W R602N */ ATH79_MACH_R6100, /* NETGEAR R6100 */ ATH79_MACH_RB_2011G, /* Mikrotik RouterBOARD 2011UAS-2HnD */ ATH79_MACH_RB_2011L, /* Mikrotik RouterBOARD 2011L */ diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk index 34bb7da84d..37ffbe7ffa 100644 --- a/target/linux/ar71xx/image/generic.mk +++ b/target/linux/ar71xx/image/generic.mk @@ -85,6 +85,14 @@ define Device/cf-e530n endef TARGET_DEVICES += cf-e530n +define Device/cpe505n + DEVICE_TITLE := P&W CPE505N + BOARDNAME = CPE505N + IMAGE_SIZE = 16000k + MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro +endef +TARGET_DEVICES += cpe505n + define Device/cpe830 $(Device/ap90q) DEVICE_TITLE := YunCore CPE830 @@ -426,6 +434,15 @@ define Device/jwap230 endef TARGET_DEVICES += jwap230 +define Device/r602n + DEVICE_TITLE := P&W R602N + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 + BOARDNAME = R602N + IMAGE_SIZE = 16000k + MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro +endef +TARGET_DEVICES += r602n + define Device/rnx-n360rt $(Device/tplink-4m) DEVICE_TITLE := Rosewill RNX-N360RT diff --git a/target/linux/ar71xx/mikrotik/config-default b/target/linux/ar71xx/mikrotik/config-default index 78a3fb340e..1cc485a7d1 100644 --- a/target/linux/ar71xx/mikrotik/config-default +++ b/target/linux/ar71xx/mikrotik/config-default @@ -35,6 +35,7 @@ # CONFIG_ATH79_MACH_CF_E380AC_V2 is not set # CONFIG_ATH79_MACH_CF_E520N is not set # CONFIG_ATH79_MACH_CF_E530N is not set +# CONFIG_ATH79_MACH_CPE505N is not set # CONFIG_ATH79_MACH_CPE510 is not set # CONFIG_ATH79_MACH_CPE830 is not set # CONFIG_ATH79_MACH_CPE870 is not set @@ -108,6 +109,7 @@ # CONFIG_ATH79_MACH_PB44 is not set # CONFIG_ATH79_MACH_PQI_AIR_PEN is not set # CONFIG_ATH79_MACH_QIHOO_C301 is not set +# CONFIG_ATH79_MACH_R602N is not set # CONFIG_ATH79_MACH_R6100 is not set CONFIG_ATH79_MACH_RB2011=y CONFIG_ATH79_MACH_RB4XX=y diff --git a/target/linux/ar71xx/nand/config-default b/target/linux/ar71xx/nand/config-default index 8a9b61c057..16e652ed4e 100644 --- a/target/linux/ar71xx/nand/config-default +++ b/target/linux/ar71xx/nand/config-default @@ -34,6 +34,7 @@ # CONFIG_ATH79_MACH_CF_E380AC_V2 is not set # CONFIG_ATH79_MACH_CF_E520N is not set # CONFIG_ATH79_MACH_CF_E530N is not set +# CONFIG_ATH79_MACH_CPE505N is not set # CONFIG_ATH79_MACH_CPE510 is not set # CONFIG_ATH79_MACH_CPE830 is not set # CONFIG_ATH79_MACH_CPE870 is not set @@ -104,6 +105,7 @@ # CONFIG_ATH79_MACH_PB44 is not set # CONFIG_ATH79_MACH_PQI_AIR_PEN is not set # CONFIG_ATH79_MACH_QIHOO_C301 is not set +# CONFIG_ATH79_MACH_R602N is not set # CONFIG_ATH79_MACH_RE450 is not set # CONFIG_ATH79_MACH_RW2458N is not set # CONFIG_ATH79_MACH_SC1750 is not set -- 2.25.1