From 43db8e3e41c4e70641c64984918572dfe3facdb1 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Wed, 9 Oct 2019 12:53:57 -0500 Subject: [PATCH] ARM: imx6q_logic: Remove legacy pinmuxing code from board file. With the OCRAM expanded to 256KB and the SPL_PINCTRL enabled with -u-boot.dtsi entries to include the pinmuxing in SPL, the manual code setting up the pinmux can go away. This patch removes the legacy pinmuxing code from the board file. Signed-off-by: Adam Ford Reviewed-by: Fabio Estevam --- board/logicpd/imx6/imx6logic.c | 85 ---------------------------------- 1 file changed, 85 deletions(-) diff --git a/board/logicpd/imx6/imx6logic.c b/board/logicpd/imx6/imx6logic.c index 4bacd8660a..3c1a3a9fa2 100644 --- a/board/logicpd/imx6/imx6logic.c +++ b/board/logicpd/imx6/imx6logic.c @@ -42,32 +42,6 @@ int dram_init(void) return 0; } -static iomux_v3_cfg_t const uart1_pads[] = { - MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -static iomux_v3_cfg_t const uart2_pads[] = { - MX6_PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_SD4_DAT5__UART2_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_SD4_DAT6__UART2_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -static iomux_v3_cfg_t const uart3_pads[] = { - MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_EB3__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -static void setup_iomux_uart(void) -{ - imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); - imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); - imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads)); -} - static iomux_v3_cfg_t const nand_pads[] = { MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL), MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NAND_PAD_CTRL), @@ -135,7 +109,6 @@ int overwrite_console(void) int board_early_init_f(void) { - setup_iomux_uart(); setup_nand_pins(); return 0; } @@ -177,36 +150,6 @@ int spl_start_uboot(void) } #endif -/* SD interface */ -#define USDHC_PAD_CTRL \ - (PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ - PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -static iomux_v3_cfg_t const usdhc1_pads[] = { - MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), -}; - -static iomux_v3_cfg_t const usdhc2_pads[] = { - MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ -}; - -#ifdef CONFIG_FSL_ESDHC_IMX -struct fsl_esdhc_cfg usdhc_cfg[] = { - {USDHC1_BASE_ADDR}, /* SOM */ - {USDHC2_BASE_ADDR} /* Baseboard */ -}; - void board_boot_order(u32 *spl_boot_list) { struct src *psrc = (struct src *)SRC_BASE_ADDR; @@ -236,34 +179,6 @@ void board_boot_order(u32 *spl_boot_list) spl_boot_list[2] = BOOT_DEVICE_BOARD; } -int board_mmc_init(bd_t *bis) -{ - struct src *psrc = (struct src *)SRC_BASE_ADDR; - unsigned int reg = readl(&psrc->sbmr1) >> 11; - /* - * Upon reading BOOT_CFG register the following map is done: - * Bit 11 and 12 of BOOT_CFG register can determine the current - * mmc port - * 0x1 SD1-SOM - * 0x2 SD2-Baseboard - */ - - reg &= 0x3; /* Only care about bottom 2 bits */ - - switch (reg) { - case 0: - SETUP_IOMUX_PADS(usdhc1_pads); - break; - case 1: - SETUP_IOMUX_PADS(usdhc2_pads); - break; - } - - return 0; -} - -#endif - static void ccgr_init(void) { struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; -- 2.25.1