From 39782afb1ae86c15e59b1118278513a1a545652c Mon Sep 17 00:00:00 2001 From: Simon Glass Date: Mon, 4 Jul 2016 11:58:07 -0600 Subject: [PATCH] dm: Add a README for of-platdata Add documentation on how this works, including the benefits and drawbacks. Signed-off-by: Simon Glass --- doc/driver-model/of-plat.txt | 268 +++++++++++++++++++++++++++++++++++ 1 file changed, 268 insertions(+) create mode 100644 doc/driver-model/of-plat.txt diff --git a/doc/driver-model/of-plat.txt b/doc/driver-model/of-plat.txt new file mode 100644 index 0000000000..96b9b4642c --- /dev/null +++ b/doc/driver-model/of-plat.txt @@ -0,0 +1,268 @@ +Driver Model Compiled-in Device Tree / Platform Data +==================================================== + + +Introduction +------------ + +Device tree is the standard configuration method in U-Boot. It is used to +define what devices are in the system and provide configuration information +to these devices. + +The overhead of adding device tree access to U-Boot is fairly modest, +approximately 3KB on Thumb 2 (plus the size of the DT itself). This means +that in most cases it is best to use device tree for configuration. + +However there are some very constrained environments where U-Boot needs to +work. These include SPL with severe memory limitations. For example, some +SoCs require a 16KB SPL image which must include a full MMC stack. In this +case the overhead of device tree access may be too great. + +It is possible to create platform data manually by defining C structures +for it, and referencing that data in a U_BOOT_DEVICE() declaration. This +bypasses the use of device tree completely, but is an available option for +SPL. + +As an alternative, a new 'of-platdata' feature is provided. This converts +device tree contents into C code which can be compiled into the SPL binary. +This saves the 3KB of code overhead and perhaps a few hundred more bytes due +to more efficient storage of the data. + + +Caveats +------- + +There are many problems with this features. It should only be used when +stricly necessary. Notable problems include: + + - Device tree does not describe data types but the C code must define a + type for each property. Thesee are guessed using heuristics which + are wrong in several fairly common cases. For example an 8-byte value + is considered to be a 2-item integer array, and is byte-swapped. A + boolean value that is not present means 'false', but cannot be + included in the structures since there is generally no mention of it + in the device tree file. + + - Naming of nodes and properties is automatic. This means that they follow + the naming in the device tree, which may result in C identifiers that + look a bit strange + + - It is not possible to find a value given a property name. Code must use + the associated C member variable directly in the code. This makes + the code less robust in the face of device-tree changes. It also + makes it very unlikely that your driver code will be useful for more + than one SoC. Even if the code is common, each SoC will end up with + a different C struct and format for the platform data. + + - The platform data is provided to drivers as a C structure. The driver + must use the same structure to access the data. Since a driver + normally also supports device tree it must use #ifdef to separate + out this code, since the structures are only available in SPL. + + +How it works +------------ + +The feature is enabled by CONFIG SPL_OF_PLATDATA. This is only available +in SPL and should be tested with: + + #if CONFIG_IS_ENABLED(SPL_OF_PLATDATA) + +A new tool called 'dtoc' converts a device tree file either into a set of +struct declarations, one for each compatible node, or a set of +U_BOOT_DEVICE() declarations along with the actual platform data for each +device. As an example, consider this MMC node: + + sdmmc: dwmmc@ff0c0000 { + compatible = "rockchip,rk3288-dw-mshc"; + clock-freq-min-max = <400000 150000000>; + clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>, + <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu_drv", "ciu_sample"; + fifo-depth = <0x100>; + interrupts = ; + reg = <0xff0c0000 0x4000>; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + card-detect-delay = <200>; + disable-wp; + num-slots = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>; + vmmc-supply = <&vcc_sd>; + status = "okay"; + u-boot,dm-pre-reloc; + }; + + +Some of these properties are dropped by U-Boot under control of the +CONFIG_OF_SPL_REMOVE_PROPS option. The rest are processed. This will produce +the following C struct declaration: + +struct dtd_rockchip_rk3288_dw_mshc { + fdt32_t bus_width; + bool cap_mmc_highspeed; + bool cap_sd_highspeed; + fdt32_t card_detect_delay; + fdt32_t clock_freq_min_max[2]; + struct phandle_2_cell clocks[4]; + bool disable_wp; + fdt32_t fifo_depth; + fdt32_t interrupts[3]; + fdt32_t num_slots; + fdt32_t reg[2]; + bool u_boot_dm_pre_reloc; + fdt32_t vmmc_supply; +}; + +and the following device declaration: + +static struct dtd_rockchip_rk3288_dw_mshc dtv_dwmmc_at_ff0c0000 = { + .fifo_depth = 0x100, + .cap_sd_highspeed = true, + .interrupts = {0x0, 0x20, 0x4}, + .clock_freq_min_max = {0x61a80, 0x8f0d180}, + .vmmc_supply = 0xb, + .num_slots = 0x1, + .clocks = {{&dtv_clock_controller_at_ff760000, 456}, {&dtv_clock_controller_at_ff760000, 68}, {&dtv_clock_controller_at_ff760000, 114}, {&dtv_clock_controller_at_ff760000, 118}}, + .cap_mmc_highspeed = true, + .disable_wp = true, + .bus_width = 0x4, + .u_boot_dm_pre_reloc = true, + .reg = {0xff0c0000, 0x4000}, + .card_detect_delay = 0xc8, +}; +U_BOOT_DEVICE(dwmmc_at_ff0c0000) = { + .name = "rockchip_rk3288_dw_mshc", + .platdata = &dtv_dwmmc_at_ff0c0000, +}; + +The device is then instantiated at run-time and the platform data can be +accessed using: + + struct udevice *dev; + struct dtd_rockchip_rk3288_dw_mshc *plat = dev_get_platdata(dev); + +This avoids the code overhead of converting the device tree data to +platform data in the driver. The ofdata_to_platdata() method should +therefore do nothing in such a driver. + + +How to structure your driver +---------------------------- + +Drivers should always support device tree as an option. The of-platdata +feature is intended as a add-on to existing drivers. + +Your driver should directly access the platdata struct in its probe() +method. The existing device tree decoding logic should be kept in the +ofdata_to_platdata() and wrapped with #ifdef. + +For example: + + #include + + struct mmc_platdata { + #if CONFIG_IS_ENABLED(SPL_OF_PLATDATA) + /* Put this first */ + struct dtd_mmc dtplat; + #endif + /* + * Other fields can go here, to be filled in by decoding from + * the device tree. They will point to random memory in the + * of-plat case. + */ + int fifo_depth; + }; + + static int mmc_ofdata_to_platdata(struct udevice *dev) + { + #if !CONFIG_IS_ENABLED(SPL_OF_PLATDATA) + struct mmc_platdata *plat = dev_get_platdata(dev); + const void *blob = gd->fdt_blob; + int node = dev->of_offset; + + plat->fifo_depth = fdtdec_get_int(blob, node, "fifo-depth", 0); + #endif + + return 0; + } + + static int mmc_probe(struct udevice *dev) + { + struct mmc_platdata *plat = dev_get_platdata(dev); + #if CONFIG_IS_ENABLED(SPL_OF_PLATDATA) + struct dtd_mmc *dtplat = &plat->dtplat; + + /* Set up the device from the dtplat data */ + writel(dtplat->fifo_depth, ...) + #else + /* Set up the device from the plat data */ + writel(plat->fifo_depth, ...) + #endif + } + + static const struct udevice_id mmc_ids[] = { + { .compatible = "vendor,mmc" }, + { } + }; + + U_BOOT_DRIVER(mmc_drv) = { + .name = "mmc", + .id = UCLASS_MMC, + .of_match = mmc_ids, + .ofdata_to_platdata = mmc_ofdata_to_platdata, + .probe = mmc_probe, + .priv_auto_alloc_size = sizeof(struct mmc_priv), + .platdata_auto_alloc_size = sizeof(struct mmc_platdata), + }; + + +In the case where SPL_OF_PLATDATA is enabled, platdata_auto_alloc_size is +ignored, and the platform data points to the C structure data. In the case +where device tree is used, the platform data is allocated, and starts +zeroed. In this case the ofdata_to_platdata() method should set up the +platform data. + +SPL must use either of-platdata or device tree. Drivers cannot use both. +The device tree becomes in accessible when CONFIG_SPL_OF_PLATDATA is enabled, +since the device-tree access code is not compiled in. + + +Internals +--------- + +The dt-structs.h file includes the generated file +(include/generated//dt-structs.h) if CONFIG_SPL_OF_PLATDATA is enabled. +Otherwise (such as in U-Boot proper) these structs are not available. This +prevents them being used inadvertently. + +The dt-platdata.c file contains the device declarations and is is built in +spl/dt-platdata.c. + +Some phandles (thsoe that are recognised as such) are converted into +points to platform data. This pointer can potentially be used to access the +referenced device (by searching for the pointer value). This feature is not +yet implemented, however. + +The beginnings of a libfdt Python module are provided. So far this only +implements a subset of the features. + +The 'swig' tool is needed to build the libfdt Python module. + + +Future work +----------- +- Add unit tests +- Add a sandbox_spl functional test +- Consider programmatically reading binding files instead of device tree + contents +- Drop the device tree data from the SPL image +- Complete the phandle feature +- Get this running on a Rockchip board +- Move to using a full Python libfdt module + +-- +Simon Glass +6/6/16 -- 2.25.1