From 3358cae5238d66c73b0328b007a1cbb073bc8275 Mon Sep 17 00:00:00 2001 From: INAGAKI Hiroshi Date: Fri, 30 Nov 2018 19:04:23 +0900 Subject: [PATCH] ath79: add support for I-O DATA WN-AG300DGR MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi --- .../ath79/base-files/etc/board.d/02_network | 4 +- .../etc/hotplug.d/firmware/10-ath9k-eeprom | 3 +- .../etc/hotplug.d/ieee80211/10_fix_wifi_mac | 6 + .../ath79/dts/ar1022_iodata_wn-ag300dgr.dts | 222 ++++++++++++++++++ target/linux/ath79/image/generic.mk | 12 + 5 files changed, 245 insertions(+), 2 deletions(-) create mode 100644 target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 266a18791a..fa7a618909 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -82,6 +82,7 @@ ath79_setup_interfaces() iodata,etg3-r|\ iodata,wn-ac1167dgr|\ iodata,wn-ac1600dgr2|\ + iodata,wn-ag300dgr|\ pcs,cr5000) ucidef_add_switch "switch0" \ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" @@ -223,7 +224,8 @@ ath79_setup_macs() wan_mac=$(macaddr_add "$lan_mac" -1) ;; iodata,wn-ac1167dgr|\ - iodata,wn-ac1600dgr2) + iodata,wn-ac1600dgr2|\ + iodata,wn-ag300dgr) lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr) wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr) ;; diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index c5cbac7514..e4d4a597a9 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -101,7 +101,8 @@ case "$FIRMWARE" in ath9k_eeprom_extract_reverse "urlader" 5441 1088 ;; iodata,wn-ac1167dgr|\ - iodata,wn-ac1600dgr2) + iodata,wn-ac1600dgr2|\ + iodata,wn-ag300dgr) ath9k_eeprom_extract "art" 4096 1088 ath9k_patch_fw_mac $(mtd_get_mac_ascii u-boot-env ethaddr) 2 ;; diff --git a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index fe5aa64a19..bb55b1c11c 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -13,6 +13,12 @@ PHYNBR=${DEVPATH##*/phy} board=$(board_name) case "$board" in + iodata,wn-ag300dgr) + # There is no eeprom data for 5 GHz wlan in "art" partition + # which would allow to patch the macaddress + [ "$PHYNBR" -eq 1 ] && \ + echo $(macaddr_add "$(mtd_get_mac_ascii u-boot-env ethaddr)" 1) > /sys${DEVPATH}/macaddress + ;; phicomm,k2t) # The K2T factory firmware does use LAN mac address as the 2.4G wifi mac address [ "$PHYNBR" -eq 1 ] && \ diff --git a/target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts b/target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts new file mode 100644 index 0000000000..b222b10a5a --- /dev/null +++ b/target/linux/ath79/dts/ar1022_iodata_wn-ag300dgr.dts @@ -0,0 +1,222 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar9344.dtsi" + +/ { + compatible = "iodata,wn-ag300dgr", "qca,ar9344"; + model = "I-O DATA WN-AG300DGR"; + + aliases { + led-boot = &router; + led-failsafe = &router; + led-running = &router; + led-upgrade = &router; + }; + + leds { + compatible = "gpio-leds"; + + router: router { + label = "wn-ag300dgr:green:router"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + children { + label = "wn-ag300dgr:green:children"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + eco { + label = "wn-ag300dgr:green:eco"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + notification { + label = "wn-ag300dgr:amber:notification"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + wlan2g { + label = "wn-ag300dgr:green:wlan2g"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "wn-ag300dgr:green:wlan5g"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + default-state = "off"; + linux,default-trigger = "phy1tpt"; + }; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + eco { + label = "eco"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + router { + label = "router"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + debounce-interval = <60>; + }; + + auto { + label = "auto"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + debounce-interval = <60>; + }; + + wps { + label = "wps"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + reset { + label = "reset"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + children { + label = "children"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; +}; + +&ref { + clock-frequency = <25000000>; +}; + +&spi { + num-cs = <1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x030000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x030000 0x010000>; + read-only; + }; + + partition@40000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x040000 0xf10000>; + }; + + partition@f50000 { + label = "manufacture"; + reg = <0xf50000 0x40000>; + read-only; + }; + + partition@f90000 { + label = "backup"; + reg = <0xf90000 0x10000>; + read-only; + }; + + partition@fa0000 { + label = "storage"; + reg = <0xfa0000 0x50000>; + read-only; + }; + + partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "rgmii"; + + qca,ar8327-initvals = < + 0x04 0x07a00000 /* PORT0 PAD MODE CTRL */ + 0x7c 0x000000fe /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x06000000 0x00000101 0x00001616>; + + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + gmac-config { + device = <&gmac>; + rgmii-gmac0 = <1>; + }; +}; + +&pcie { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&wmac { + status = "okay"; + qca,no-eeprom; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 74d185ea63..df91c91826 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -222,6 +222,18 @@ define Device/iodata_wn-ac1600dgr2 endef TARGET_DEVICES += iodata_wn-ac1600dgr2 +define Device/iodata_wn-ag300dgr + ATH_SOC := ar1022 + DEVICE_TITLE := I-O DATA WN-AG300DGR + IMAGE_SIZE := 15424k + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \ + senao-header -r 0x30a -p 0x47 -t 2 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 +endef +TARGET_DEVICES += iodata_wn-ag300dgr + define Device/ocedo_koala ATH_SOC := qca9558 DEVICE_TITLE := OCEDO Koala -- 2.25.1