From 2ac07f75d1977008e829d00bcce16143e171765d Mon Sep 17 00:00:00 2001 From: David Lechner Date: Fri, 26 Feb 2016 00:46:07 -0600 Subject: [PATCH] arm: Add support for LEGO MINDSTORMS EV3 This is based on the davinci da850evm. It can boot from either the on-board 16MB flash or from a microSD card. It also reads board information from an I2C EEPROM. The EV3 itself initally boots from write-protected EEPROM, so no u-boot SPL is needed. Signed-off-by: David Lechner Reviewed-by: Tom Rini --- arch/arm/mach-davinci/Kconfig | 4 + arch/arm/mach-davinci/da850_pinmux.c | 10 + arch/arm/mach-davinci/include/mach/hardware.h | 1 + board/lego/ev3/Kconfig | 12 + board/lego/ev3/MAINTAINERS | 6 + board/lego/ev3/Makefile | 10 + board/lego/ev3/README | 32 +++ board/lego/ev3/legoev3.c | 176 ++++++++++++ configs/legoev3_defconfig | 12 + include/configs/legoev3.h | 255 ++++++++++++++++++ 10 files changed, 518 insertions(+) create mode 100644 board/lego/ev3/Kconfig create mode 100644 board/lego/ev3/MAINTAINERS create mode 100644 board/lego/ev3/Makefile create mode 100644 board/lego/ev3/README create mode 100644 board/lego/ev3/legoev3.c create mode 100644 configs/legoev3_defconfig create mode 100644 include/configs/legoev3.h diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index a8d3e2f230..5d1c5c5ccb 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -22,6 +22,9 @@ config TARGET_OMAPL138_LCDK config TARGET_CALIMAIN bool "Calimain board" +config TARGET_LEGOEV3 + bool "LEGO MINDSTORMS EV3" + endchoice config SYS_SOC @@ -31,5 +34,6 @@ source "board/Barix/ipam390/Kconfig" source "board/davinci/da8xxevm/Kconfig" source "board/davinci/ea20/Kconfig" source "board/omicron/calimain/Kconfig" +source "board/lego/ev3/Kconfig" endif diff --git a/arch/arm/mach-davinci/da850_pinmux.c b/arch/arm/mach-davinci/da850_pinmux.c index 6105f6390c..758109e98d 100644 --- a/arch/arm/mach-davinci/da850_pinmux.c +++ b/arch/arm/mach-davinci/da850_pinmux.c @@ -12,6 +12,16 @@ #include /* SPI pin muxer settings */ +const struct pinmux_config spi0_pins_base[] = { + { pinmux(3), 1, 0 }, /* SPI0_CLK */ + { pinmux(3), 1, 2 }, /* SPI0_SOMI */ + { pinmux(3), 1, 3 }, /* SPI0_SIMO */ +}; + +const struct pinmux_config spi0_pins_scs0[] = { + { pinmux(4), 1, 1 }, /* SPI0_SCS[0] */ +}; + const struct pinmux_config spi1_pins_base[] = { { pinmux(5), 1, 2 }, /* SPI1_CLK */ { pinmux(5), 1, 4 }, /* SPI1_SOMI */ diff --git a/arch/arm/mach-davinci/include/mach/hardware.h b/arch/arm/mach-davinci/include/mach/hardware.h index a4eb0bd89b..2a0360a785 100644 --- a/arch/arm/mach-davinci/include/mach/hardware.h +++ b/arch/arm/mach-davinci/include/mach/hardware.h @@ -503,6 +503,7 @@ struct davinci_syscfg_regs { #define DAVINCI_SYSCFG_SUSPSRC_SPI0 (1 << 21) #define DAVINCI_SYSCFG_SUSPSRC_SPI1 (1 << 22) #define DAVINCI_SYSCFG_SUSPSRC_UART0 (1 << 18) +#define DAVINCI_SYSCFG_SUSPSRC_UART1 (1 << 19) #define DAVINCI_SYSCFG_SUSPSRC_UART2 (1 << 20) #define DAVINCI_SYSCFG_SUSPSRC_TIMER0 (1 << 27) diff --git a/board/lego/ev3/Kconfig b/board/lego/ev3/Kconfig new file mode 100644 index 0000000000..14b3f0c1cf --- /dev/null +++ b/board/lego/ev3/Kconfig @@ -0,0 +1,12 @@ +if TARGET_LEGOEV3 + +config SYS_BOARD + default "ev3" + +config SYS_VENDOR + default "lego" + +config SYS_CONFIG_NAME + default "legoev3" + +endif diff --git a/board/lego/ev3/MAINTAINERS b/board/lego/ev3/MAINTAINERS new file mode 100644 index 0000000000..11b3261609 --- /dev/null +++ b/board/lego/ev3/MAINTAINERS @@ -0,0 +1,6 @@ +LEGOEV3 BOARD +M: David Lechner +S: Maintained +F: board/lego/ev3/ +F: include/configs/legoev3.h +F: configs/legoev3_defconfig diff --git a/board/lego/ev3/Makefile b/board/lego/ev3/Makefile new file mode 100644 index 0000000000..f3e717ab66 --- /dev/null +++ b/board/lego/ev3/Makefile @@ -0,0 +1,10 @@ +# +# (C) Copyright 2000, 2001, 2002 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# Copyright (C) 2007 Sergey Kubushyn +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += legoev3.o diff --git a/board/lego/ev3/README b/board/lego/ev3/README new file mode 100644 index 0000000000..1a50ca9d03 --- /dev/null +++ b/board/lego/ev3/README @@ -0,0 +1,32 @@ +Summary +======= + +LEGO MINDSTORMS EV3 is a toy robot produced by the LEGO Group. It is based +on the davinci da850 evm. The EV3 has a 16MB spi flash and a SDHC microSD card +reader. + +Booting +======= + +The EV3 contains a bootloader in EEPROM that loads u-boot.bin from address 0x0 +of the spi flash memory. Using the default configuration, u-boot will check to +see if there is a boot.scr file on the first FAT partition of the mmc. If there +is, it will run the script and boot the kernel from the uImage file also in +the FAT partition. Otherwise, it will load a kernel and rootfs from the flash. +The kernel must be stored at address 0x50000 on the flash and have a maximum +size of 3MiB. The rootfs must be a squasfs image and stored at 0x350000 in the +flash and have a maximum size of 9.3MiB. The flash starting at 0xCB0000 is +reserved for user data. + +Writing image to flash +====================== + +The EEPROM contains a program for uploading an image file to the flash memory. +The program is started by holding down the right button on the EV3 when powering +it on. You can also `run fwupdateboot` in the u-boot shell to reboot into this +mode. The image can then be uploaded using the official LEGO MINDSTORMS EV3 +software or a 3rd party program capable of uploading a firmware file. + +If you are booting from the microSD card, it is enough to just write uboot.bin +to the flash. If you are not using a microSD card, you will need to create an +image file using the layout described above. diff --git a/board/lego/ev3/legoev3.c b/board/lego/ev3/legoev3.c new file mode 100644 index 0000000000..a791b97f8f --- /dev/null +++ b/board/lego/ev3/legoev3.c @@ -0,0 +1,176 @@ +/* + * Copyright (C) 2016 David Lechner + * + * Based on da850evm.c + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on da830evm.c. Original Copyrights follow: + * + * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. + * Copyright (C) 2007 Sergey Kubushyn + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_DAVINCI_MMC +#include +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +u8 board_rev; + +#define EEPROM_I2C_ADDR 0x50 +#define EEPROM_REV_OFFSET 0x3F00 +#define EEPROM_MAC_OFFSET 0x3F06 + +#ifdef CONFIG_DAVINCI_MMC +static struct davinci_mmc mmc_sd0 = { + .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE, + .host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */ + .voltages = MMC_VDD_32_33 | MMC_VDD_33_34, + .version = MMC_CTLR_VERSION_2, +}; + +int board_mmc_init(bd_t *bis) +{ + mmc_sd0.input_clk = clk_get(DAVINCI_MMCSD_CLKID); + + /* Add slot-0 to mmc subsystem */ + return davinci_mmc_init(bis, &mmc_sd0); +} +#endif + +const struct pinmux_resource pinmuxes[] = { + PINMUX_ITEM(spi0_pins_base), + PINMUX_ITEM(spi0_pins_scs0), + PINMUX_ITEM(uart1_pins_txrx), + PINMUX_ITEM(i2c0_pins), + PINMUX_ITEM(mmc0_pins), +}; + +const int pinmuxes_size = ARRAY_SIZE(pinmuxes); + +const struct lpsc_resource lpsc[] = { + { DAVINCI_LPSC_SPI0 }, /* Serial Flash */ + { DAVINCI_LPSC_UART1 }, /* console */ + { DAVINCI_LPSC_MMC_SD }, +}; + +const int lpsc_size = ARRAY_SIZE(lpsc); + +u32 get_board_rev(void) +{ + u8 buf[2]; + + if (!board_rev) { + if (i2c_read(EEPROM_I2C_ADDR, EEPROM_REV_OFFSET, 2, buf, 2)) { + printf("\nBoard revision read failed!\n"); + } else { + /* + * Board rev 3 has MAC address at EEPROM_REV_OFFSET. + * Other revisions have checksum at EEPROM_REV_OFFSET+1 + * to detect this. + */ + if ((buf[0] ^ buf[1]) == 0xFF) + board_rev = buf[0]; + else + board_rev = 3; + } + } + + return board_rev; +} + +/* + * The Bluetooth MAC address serves as the board serial number. + */ +void get_board_serial(struct tag_serialnr *serialnr) +{ + u32 offset; + u8 buf[6]; + + if (!board_rev) + board_rev = get_board_rev(); + + /* Board rev 3 has MAC address where rev should be */ + offset = (board_rev == 3) ? EEPROM_REV_OFFSET : EEPROM_MAC_OFFSET; + + if (i2c_read(EEPROM_I2C_ADDR, offset, 2, buf, 6)) { + printf("\nBoard serial read failed!\n"); + } else { + u8 *nr; + + nr = (u8 *)&serialnr->low; + nr[0] = buf[5]; + nr[1] = buf[4]; + nr[2] = buf[3]; + nr[3] = buf[2]; + nr = (u8 *)&serialnr->high; + nr[0] = buf[1]; + nr[1] = buf[0]; + nr[2] = 0; + nr[3] = 0; + } +} + +int board_early_init_f(void) +{ + /* + * Power on required peripherals + * ARM does not have access by default to PSC0 and PSC1 + * assuming here that the DSP bootloader has set the IOPU + * such that PSC access is available to ARM + */ + if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc))) + return 1; + + return 0; +} + +int board_init(void) +{ +#ifndef CONFIG_USE_IRQ + irq_init(); +#endif + + /* arch number of the board */ + /* LEGO didn't register for a unique number and uses da850evm */ + gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM; + + /* address of boot parameters */ + gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR; + + /* setup the SUSPSRC for ARM to control emulation suspend */ + writel(readl(&davinci_syscfg_regs->suspsrc) & + ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C | + DAVINCI_SYSCFG_SUSPSRC_SPI0 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 | + DAVINCI_SYSCFG_SUSPSRC_UART1), + &davinci_syscfg_regs->suspsrc); + + /* configure pinmux settings */ + if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes))) + return 1; + + /* enable the console UART */ + writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | + DAVINCI_UART_PWREMU_MGMT_UTRST), + &davinci_uart1_ctrl_regs->pwremu_mgmt); + + return 0; +} diff --git a/configs/legoev3_defconfig b/configs/legoev3_defconfig new file mode 100644 index 0000000000..d838baa32c --- /dev/null +++ b/configs/legoev3_defconfig @@ -0,0 +1,12 @@ +CONFIG_ARM=y +CONFIG_ARCH_DAVINCI=y +CONFIG_TARGET_LEGOEV3=y +CONFIG_AUTOBOOT_KEYED=y +CONFIG_AUTOBOOT_PROMPT="Autoboot in %d seconds - press 'l' to stop...\n" +CONFIG_AUTOBOOT_STOP_STR="l" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_SETEXPR is not set +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SYS_NS16550=y diff --git a/include/configs/legoev3.h b/include/configs/legoev3.h new file mode 100644 index 0000000000..79fa3c476a --- /dev/null +++ b/include/configs/legoev3.h @@ -0,0 +1,255 @@ +/* + * Copyright (C) 2016 David Lechner + * + * Based on da850evm.h + * + * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ + * + * Based on davinci_dvevm.h. Original Copyrights follow: + * + * Copyright (C) 2007 Sergey Kubushyn + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * SoC Configuration + */ +#define CONFIG_MACH_DAVINCI_DA850_EVM +#define CONFIG_SOC_DA8XX /* TI DA8xx SoC */ +#define CONFIG_SOC_DA850 /* TI DA850 SoC */ +#define CONFIG_SYS_EXCEPTION_VECTORS_HIGH +#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID) +#define CONFIG_SYS_OSCIN_FREQ 24000000 +#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE +#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID) +#define CONFIG_SYS_DA850_PLL_INIT +#define CONFIG_SYS_DA850_DDR_INIT + +#define CONFIG_SYS_TEXT_BASE 0xc1080000 + + +/* + * Memory Info + */ +#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */ +#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */ +#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */ +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/ + +/* memtest start addr */ +#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000) + +/* memtest will be run on 16MB */ +#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024) + +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ + +#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \ + DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \ + DAVINCI_SYSCFG_SUSPSRC_SPI0 | \ + DAVINCI_SYSCFG_SUSPSRC_UART1 | \ + DAVINCI_SYSCFG_SUSPSRC_EMAC | \ + DAVINCI_SYSCFG_SUSPSRC_I2C) + +/* + * PLL configuration + */ +#define CONFIG_SYS_DV_CLKMODE 0 +#define CONFIG_SYS_DA850_PLL0_POSTDIV 1 +#define CONFIG_SYS_DA850_PLL0_PLLDIV1 0x8000 +#define CONFIG_SYS_DA850_PLL0_PLLDIV2 0x8001 +#define CONFIG_SYS_DA850_PLL0_PLLDIV3 0x8002 +#define CONFIG_SYS_DA850_PLL0_PLLDIV4 0x8003 +#define CONFIG_SYS_DA850_PLL0_PLLDIV5 0x8002 +#define CONFIG_SYS_DA850_PLL0_PLLDIV6 CONFIG_SYS_DA850_PLL0_PLLDIV1 +#define CONFIG_SYS_DA850_PLL0_PLLDIV7 0x8005 + +#define CONFIG_SYS_DA850_PLL1_POSTDIV 1 +#define CONFIG_SYS_DA850_PLL1_PLLDIV1 0x8000 +#define CONFIG_SYS_DA850_PLL1_PLLDIV2 0x8001 +#define CONFIG_SYS_DA850_PLL1_PLLDIV3 0x8002 + +#define CONFIG_SYS_DA850_PLL0_PLLM 24 +#define CONFIG_SYS_DA850_PLL1_PLLM 21 + +/* + * DDR2 memory configuration + */ +#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \ + DV_DDR_PHY_EXT_STRBEN | \ + (0x4 << DV_DDR_PHY_RD_LATENCY_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDBCR ( \ + (1 << DV_DDR_SDCR_MSDRAMEN_SHIFT) | \ + (1 << DV_DDR_SDCR_DDREN_SHIFT) | \ + (1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \ + (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \ + (0x3 << DV_DDR_SDCR_CL_SHIFT) | \ + (0x2 << DV_DDR_SDCR_IBANK_SHIFT) | \ + (0x2 << DV_DDR_SDCR_PAGESIZE_SHIFT)) + +/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */ +#define CONFIG_SYS_DA850_DDR2_SDBCR2 0 + +#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \ + (14 << DV_DDR_SDTMR1_RFC_SHIFT) | \ + (2 << DV_DDR_SDTMR1_RP_SHIFT) | \ + (2 << DV_DDR_SDTMR1_RCD_SHIFT) | \ + (1 << DV_DDR_SDTMR1_WR_SHIFT) | \ + (5 << DV_DDR_SDTMR1_RAS_SHIFT) | \ + (8 << DV_DDR_SDTMR1_RC_SHIFT) | \ + (1 << DV_DDR_SDTMR1_RRD_SHIFT) | \ + (0 << DV_DDR_SDTMR1_WTR_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \ + (7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \ + (0 << DV_DDR_SDTMR2_XP_SHIFT) | \ + (0 << DV_DDR_SDTMR2_ODT_SHIFT) | \ + (17 << DV_DDR_SDTMR2_XSNR_SHIFT) | \ + (199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \ + (0 << DV_DDR_SDTMR2_RTP_SHIFT) | \ + (0 << DV_DDR_SDTMR2_CKE_SHIFT)) + +#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000494 +#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30 + +/* + * Serial Driver info + */ +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */ +#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART1_BASE /* Base address of UART1 */ +#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID) +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ + +#define CONFIG_SPI +#define CONFIG_CMD_SF +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_BASE DAVINCI_SPI0_BASE +#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI0_CLKID) +#define CONFIG_SF_DEFAULT_SPEED 50000000 +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED + +/* + * I2C Configuration + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_DAVINCI +#define CONFIG_SYS_DAVINCI_I2C_SPEED 400000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ + +/* + * U-Boot general configuration + */ +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000) +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC +#define CONFIG_OF_LIBFDT + +/* + * Linux Information + */ +#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) +#define CONFIG_HWCONFIG /* enable hwconfig */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_REVISION_TAG +#define CONFIG_SERIAL_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_SETUP_INITRD_TAG +#define CONFIG_BOOTDELAY 0 +#define CONFIG_ZERO_BOOTDELAY_CHECK +#define CONFIG_BOOTCOMMAND \ + "if mmc rescan; then " \ + "if run loadbootscr; then " \ + "run bootscript; " \ + "else " \ + "if run loadimage; then " \ + "run mmcargs; " \ + "run mmcboot; " \ + "else " \ + "run flashargs; " \ + "run flashboot; " \ + "fi; " \ + "fi; " \ + "else " \ + "run flashargs; " \ + "run flashboot; " \ + "fi" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hostname=EV3\0" \ + "memsize=64M\0" \ + "filesyssize=10M\0" \ + "verify=n\0" \ + "console=ttyS1,115200n8\0" \ + "bootscraddr=0xC0600000\0" \ + "loadaddr=0xC0007FC0\0" \ + "filesysaddr=0xC1180000\0" \ + "fwupdateboot=mw 0xFFFF1FFC 0x5555AAAA; reset\0" \ + "mmcargs=setenv bootargs mem=${memsize} console=${console} root=/dev/mmcblk0p2 rw rootwait lpj=747520\0" \ + "mmcboot=bootm ${loadaddr}\0" \ + "flashargs=setenv bootargs mem=${memsize} initrd=${filesysaddr},${filesyssize} root=/dev/ram0 rw rootfstype=squashfs console=${console} lpj=747520\0" \ + "flashboot=sf probe 0; sf read ${loadaddr} 0x50000 0x300000; sf read ${filesysaddr} 0x350000 0x960000; bootm ${loadaddr}\0" \ + "loadimage=fatload mmc 0 ${loadaddr} uImage\0" \ + "loadbootscr=fatload mmc 0 ${bootscraddr} boot.scr\0" \ + "bootscript=source ${bootscraddr}\0" \ + +/* + * U-Boot commands + */ +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES + +#ifdef CONFIG_CMD_BDI +#define CONFIG_CLOCKS +#endif + +#define CONFIG_CMD_SPI + +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_SIZE (16 << 10) + +/* SD/MMC configuration */ +#define CONFIG_MMC +#define CONFIG_DAVINCI_MMC_SD1 +#define CONFIG_GENERIC_MMC +#define CONFIG_DAVINCI_MMC + +/* + * Enable MMC commands only when + * MMC support is present + */ +#ifdef CONFIG_MMC +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_EXT3 +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_MMC +#endif + +/* additions for new relocation code, must added to all boards */ +#define CONFIG_SYS_SDRAM_BASE 0xc0000000 + +#define CONFIG_SYS_INIT_SP_ADDR 0x80010000 + +#endif /* __CONFIG_H */ -- 2.25.1