From 21729bcdbdcd102cdb15535331d7e4b7b204a0b4 Mon Sep 17 00:00:00 2001 From: Breno Lima Date: Tue, 6 Dec 2016 15:38:25 -0200 Subject: [PATCH] udoo_neo: Add PFUZE300 PMIC support UDOO Neo boards has a PFUZE300 connected to I2C1 bus. Tested on a UDOO Neo Full with "pmic PFUZE3000 dump" command. Signed-off-by: Breno Lima --- board/udoo/neo/neo.c | 143 +++++++++++++++++++++++++++++++++++++ include/configs/udoo_neo.h | 13 ++++ 2 files changed, 156 insertions(+) diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c index cfeed6f8d7..ad7452cd91 100644 --- a/board/udoo/neo/neo.c +++ b/board/udoo/neo/neo.c @@ -19,10 +19,14 @@ #include #include #include +#include #include #include #include #include +#include +#include +#include DECLARE_GLOBAL_DATA_PTR; @@ -41,6 +45,11 @@ enum { PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) +#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ + PAD_CTL_ODE) + #define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED | \ PAD_CTL_DSE_40ohm) @@ -56,6 +65,136 @@ int dram_init(void) return 0; } +#ifdef CONFIG_SYS_I2C_MXC +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +/* I2C1 for PMIC */ +static struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC, + .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC, + .gp = IMX_GPIO_NR(1, 0), + }, + .sda = { + .i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC, + .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC, + .gp = IMX_GPIO_NR(1, 1), + }, +}; +#endif + +#ifdef CONFIG_POWER +int power_init_board(void) +{ + struct pmic *p; + int ret; + unsigned int reg, rev_id; + + ret = power_pfuze3000_init(PFUZE3000_I2C_BUS); + if (ret) + return ret; + + p = pmic_get("PFUZE3000"); + ret = pmic_probe(p); + if (ret) + return ret; + + pmic_reg_read(p, PFUZE3000_DEVICEID, ®); + pmic_reg_read(p, PFUZE3000_REVID, &rev_id); + printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id); + + /* disable Low Power Mode during standby mode */ + pmic_reg_read(p, PFUZE3000_LDOGCTL, ®); + reg |= 0x1; + ret = pmic_reg_write(p, PFUZE3000_LDOGCTL, reg); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW1AMODE, 0xc); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW1BMODE, 0xc); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW2MODE, 0xc); + if (ret) + return ret; + + ret = pmic_reg_write(p, PFUZE3000_SW3MODE, 0xc); + if (ret) + return ret; + + /* set SW1A standby voltage 0.975V */ + pmic_reg_read(p, PFUZE3000_SW1ASTBY, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(9750); + ret = pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg); + if (ret) + return ret; + + /* set SW1B standby voltage 0.975V */ + pmic_reg_read(p, PFUZE3000_SW1BSTBY, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(9750); + ret = pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg); + if (ret) + return ret; + + /* set SW1A/VDD_ARM_IN step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PFUZE3000_SW1ACONF, ®); + reg &= ~0xc0; + reg |= 0x40; + ret = pmic_reg_write(p, PFUZE3000_SW1ACONF, reg); + if (ret) + return ret; + + /* set SW1B/VDD_SOC_IN step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(p, PFUZE3000_SW1BCONF, ®); + reg &= ~0xc0; + reg |= 0x40; + ret = pmic_reg_write(p, PFUZE3000_SW1BCONF, reg); + if (ret) + return ret; + + /* set VDD_ARM_IN to 1.350V */ + pmic_reg_read(p, PFUZE3000_SW1AVOLT, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(13500); + ret = pmic_reg_write(p, PFUZE3000_SW1AVOLT, reg); + if (ret) + return ret; + + /* set VDD_SOC_IN to 1.350V */ + pmic_reg_read(p, PFUZE3000_SW1BVOLT, ®); + reg &= ~0x3f; + reg |= PFUZE3000_SW1AB_SETP(13500); + ret = pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg); + if (ret) + return ret; + + /* set DDR_1_5V to 1.350V */ + pmic_reg_read(p, PFUZE3000_SW3VOLT, ®); + reg &= ~0x0f; + reg |= PFUZE3000_SW3_SETP(13500); + ret = pmic_reg_write(p, PFUZE3000_SW3VOLT, reg); + if (ret) + return ret; + + /* set VGEN2_1V5 to 1.5V */ + pmic_reg_read(p, PFUZE3000_VLDO2CTL, ®); + reg &= ~0x0f; + reg |= PFUZE3000_VLDO_SETP(15000); + /* enable */ + reg |= 0x10; + ret = pmic_reg_write(p, PFUZE3000_VLDO2CTL, reg); + if (ret) + return ret; + + return 0; +} +#endif + static iomux_v3_cfg_t const uart1_pads[] = { MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL), MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL), @@ -115,6 +254,10 @@ int board_init(void) /* Active high for ncp692 */ gpio_direction_output(IMX_GPIO_NR(4, 16) , 1); + #ifdef CONFIG_SYS_I2C_MXC + setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + #endif + return 0; } diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h index 0357631664..0c59068231 100644 --- a/include/configs/udoo_neo.h +++ b/include/configs/udoo_neo.h @@ -90,4 +90,17 @@ #define CONFIG_IMX_THERMAL +/* I2C configs */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C1 +#define CONFIG_SYS_I2C_SPEED 100000 + +/* PMIC */ +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_PFUZE3000 +#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08 +#define PFUZE3000_I2C_BUS 0 + #endif /* __CONFIG_H */ -- 2.25.1