From 1c2926abdd7db89296a8cc7f224dd9d5d4e37a56 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 2 Apr 2008 08:39:33 +0200 Subject: [PATCH] ppc4xx: Canyonlands: Init SATA/PCIe port correctly Canyonlands (460EX) shares the first PCIe interface with the SoC SATA interface. This usage can be configured with the jumper J6. This patch correctly configures the SATA/PCIe PHY for SATA usage when this jumper is installed. Signed-off-by: Stefan Roese --- board/amcc/canyonlands/canyonlands.c | 46 ++++++++++++++++++++-------- 1 file changed, 34 insertions(+), 12 deletions(-) diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c index fa2868face..9986e9a9c6 100644 --- a/board/amcc/canyonlands/canyonlands.c +++ b/board/amcc/canyonlands/canyonlands.c @@ -43,9 +43,9 @@ int board_early_init_f(void) u32 sdr0_cust0; u32 pvr = get_pvr(); - /*------------------------------------------------------------------+ + /* * Setup the interrupt controller polarities, triggers, etc. - *------------------------------------------------------------------*/ + */ mtdcr(uic0sr, 0xffffffff); /* clear all */ mtdcr(uic0er, 0x00000000); /* disable all */ mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */ @@ -126,7 +126,28 @@ int board_early_init_f(void) return 0; } -int checkboard (void) +static void canyonlands_sata_init(int board_type) +{ + u32 reg; + + if (board_type == BOARD_CANYONLANDS_SATA) { + /* Put SATA in reset */ + SDR_WRITE(SDR0_SRST1, 0x00020001); + + /* Set the phy for SATA, not PCI-E port 0 */ + reg = SDR_READ(PESDR0_PHY_CTL_RST); + SDR_WRITE(PESDR0_PHY_CTL_RST, (reg & 0xeffffffc) | 0x00000001); + reg = SDR_READ(PESDR0_L0CLK); + SDR_WRITE(PESDR0_L0CLK, (reg & 0xfffffff8) | 0x00000007); + SDR_WRITE(PESDR0_L0CDRCTL, 0x00003111); + SDR_WRITE(PESDR0_L0DRV, 0x00000104); + + /* Bring SATA out of reset */ + SDR_WRITE(SDR0_SRST1, 0x00000000); + } +} + +int checkboard(void) { char *s = getenv("serial#"); u32 pvr = get_pvr(); @@ -161,6 +182,8 @@ int checkboard (void) } putc('\n'); + canyonlands_sata_init(gd->board_type); + return (0); } @@ -226,37 +249,36 @@ int testdram(void) } #endif -/************************************************************************* +/* * pci_target_init * * The bootstrap configuration provides default settings for the pci * inbound map (PIM). But the bootstrap config choices are limited and * may not be sufficient for a given board. - * - ************************************************************************/ + */ #if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) void pci_target_init(struct pci_controller * hose ) { - /*-------------------------------------------------------------------+ + /* * Disable everything - *-------------------------------------------------------------------*/ + */ out_le32((void *)PCIX0_PIM0SA, 0); /* disable */ out_le32((void *)PCIX0_PIM1SA, 0); /* disable */ out_le32((void *)PCIX0_PIM2SA, 0); /* disable */ out_le32((void *)PCIX0_EROMBA, 0); /* disable expansion rom */ - /*-------------------------------------------------------------------+ + /* * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 * strapping options to not support sizes such as 128/256 MB. - *-------------------------------------------------------------------*/ + */ out_le32((void *)PCIX0_PIM0LAL, CFG_SDRAM_BASE); out_le32((void *)PCIX0_PIM0LAH, 0); out_le32((void *)PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1); out_le32((void *)PCIX0_BAR0, 0); - /*-------------------------------------------------------------------+ + /* * Program the board's subsystem id/vendor id - *-------------------------------------------------------------------*/ + */ out_le16((void *)PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID); out_le16((void *)PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID); -- 2.25.1