From 13edd1706c56371dc6a67f7bef874f6d8b7af8eb Mon Sep 17 00:00:00 2001 From: Vipin Kumar Date: Mon, 26 Mar 2012 00:09:56 +0000 Subject: [PATCH] net/designware: Try configuring phy on each dw_eth_init Phy autonegotiation works only when the ethernet cable is plugged in. Since the phy was configured only at the init time, a plugged in cable was necessary to initialize the phy properly. This patch keeps a flag to check if the phy initialization has succeeded, and calls configure_phy routine at every init if this flag reports otherwise. Signed-off-by: Vipin Kumar Signed-off-by: Amit Virdi --- drivers/net/designware.c | 50 +++++++++++++++++++++++----------------- drivers/net/designware.h | 1 + 2 files changed, 30 insertions(+), 21 deletions(-) diff --git a/drivers/net/designware.c b/drivers/net/designware.c index 933032cfde..ebb1fff805 100644 --- a/drivers/net/designware.c +++ b/drivers/net/designware.c @@ -32,6 +32,8 @@ #include #include "designware.h" +static int configure_phy(struct eth_device *dev); + static void tx_descs_init(struct eth_device *dev) { struct dw_eth_dev *priv = dev->priv; @@ -144,6 +146,9 @@ static int dw_eth_init(struct eth_device *dev, bd_t *bis) struct eth_dma_regs *dma_p = priv->dma_regs_p; u32 conf; + if (priv->phy_configured != 1) + configure_phy(dev); + /* Reset ethernet hardware */ if (mac_reset(dev) < 0) return -1; @@ -422,23 +427,26 @@ static int configure_phy(struct eth_device *dev) eth_mdio_read(dev, phy_addr, MII_LPA, &anlpar); eth_mdio_read(dev, phy_addr, MII_STAT1000, &btsr); - if (btsr & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) { - priv->speed = SPEED_1000M; - if (btsr & PHY_1000BTSR_1000FD) - priv->duplex = FULL_DUPLEX; - else - priv->duplex = HALF_DUPLEX; - } else { - if (anlpar & LPA_100) - priv->speed = SPEED_100M; - else - priv->speed = SPEED_10M; - - if (anlpar & (LPA_10FULL | LPA_100FULL)) - priv->duplex = FULL_DUPLEX; - else - priv->duplex = HALF_DUPLEX; - } + if (bmsr & BMSR_ANEGCOMPLETE) { + if (btsr & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) { + priv->speed = SPEED_1000M; + if (btsr & PHY_1000BTSR_1000FD) + priv->duplex = FULL_DUPLEX; + else + priv->duplex = HALF_DUPLEX; + } else { + if (anlpar & LPA_100) + priv->speed = SPEED_100M; + else + priv->speed = SPEED_10M; + + if (anlpar & (LPA_10FULL | LPA_100FULL)) + priv->duplex = FULL_DUPLEX; + else + priv->duplex = HALF_DUPLEX; + } + } else + return -1; #else if (eth_mdio_read(dev, phy_addr, MII_BMCR, &ctrl) < 0) return -1; @@ -455,6 +463,8 @@ static int configure_phy(struct eth_device *dev) else priv->speed = SPEED_10M; #endif + priv->phy_configured = 1; + return 0; } @@ -515,14 +525,12 @@ int designware_initialize(u32 id, ulong base_addr, u32 phy_addr) priv->dma_regs_p = (struct eth_dma_regs *)(base_addr + DW_DMA_BASE_OFFSET); priv->address = phy_addr; + priv->phy_configured = 0; if (mac_reset(dev) < 0) return -1; - if (configure_phy(dev) < 0) { - printf("Phy could not be configured\n"); - return -1; - } + configure_phy(dev); dev->init = dw_eth_init; dev->send = dw_eth_send; diff --git a/drivers/net/designware.h b/drivers/net/designware.h index 42133b3310..abf729d57d 100644 --- a/drivers/net/designware.h +++ b/drivers/net/designware.h @@ -238,6 +238,7 @@ struct dw_eth_dev { u32 duplex; u32 tx_currdescnum; u32 rx_currdescnum; + u32 phy_configured; u32 padding; struct dmamacdescr tx_mac_descrtable[CONFIG_TX_DESCR_NUM]; -- 2.25.1