From 12c79a957804c13c2ba8e6606990fd6bd1f55e9a Mon Sep 17 00:00:00 2001 From: Paul Gortmaker Date: Wed, 26 Sep 2012 11:43:54 +0000 Subject: [PATCH] powerpc: delete Wind River SBC8560/8540 support The sbc8548/60 (both similar, just variations in UART hardware) support has been removed from the linux kernel as of v3.6-rc1~132 so lets also now remove it from the u-boot tree as well. Signed-off-by: Paul Gortmaker --- MAINTAINERS | 2 - board/sbc8560/Makefile | 50 ----- board/sbc8560/README | 57 ----- board/sbc8560/ddr.c | 43 ---- board/sbc8560/law.c | 60 ----- board/sbc8560/sbc8560.c | 369 ------------------------------ board/sbc8560/tlb.c | 65 ------ boards.cfg | 6 - include/configs/SBC8540.h | 428 ----------------------------------- include/configs/sbc8560.h | 459 -------------------------------------- 10 files changed, 1539 deletions(-) delete mode 100644 board/sbc8560/Makefile delete mode 100644 board/sbc8560/README delete mode 100644 board/sbc8560/ddr.c delete mode 100644 board/sbc8560/law.c delete mode 100644 board/sbc8560/sbc8560.c delete mode 100644 board/sbc8560/tlb.c delete mode 100644 include/configs/SBC8540.h delete mode 100644 include/configs/sbc8560.h diff --git a/MAINTAINERS b/MAINTAINERS index 971235bbca..ff8e47caac 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -214,9 +214,7 @@ Siddarth Gore Paul Gortmaker sbc8349 MPC8349 - sbc8540 MPC8540 sbc8548 MPC8548 - sbc8560 MPC8560 sbc8641d MPC8641D Frank Gottschling diff --git a/board/sbc8560/Makefile b/board/sbc8560/Makefile deleted file mode 100644 index ce0156040a..0000000000 --- a/board/sbc8560/Makefile +++ /dev/null @@ -1,50 +0,0 @@ -# -# (C) Copyright 2004-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# (C) Copyright 2004 Wind River Systems Inc . -# Added support for Wind River SBC8560 board -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).o - -COBJS-y += $(BOARD).o -COBJS-y += law.o -COBJS-y += tlb.o -COBJS-$(CONFIG_FSL_DDR1) += ddr.o - -SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS-y)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(obj).depend $(OBJS) $(SOBJS) - $(call cmd_link_o_target, $(OBJS)) - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/sbc8560/README b/board/sbc8560/README deleted file mode 100644 index c4b642236e..0000000000 --- a/board/sbc8560/README +++ /dev/null @@ -1,57 +0,0 @@ -The port was tested on Wind River System Sbc8560 board -. U-Boot was installed on the flash memory of the -CPU card (no the SODIMM). - -NOTE: Please configure uboot compile to the proper PCI frequency and -setup the appropriate DIP switch settings. - -SBC8560 board: - -Make sure boards switches are set to their appropriate conditions. -Refer to the Engineering Reference Guide ERG-00300-002. Of particular -importance are: 1) the settings for JP4 (JP4 1-3 and 2-4), which -select the on-board FLASH device (Intel 28F128Jx); 2) The settings -for the Clock SW9 (33 MHz or 66 MHz). - - Note: SW9 Settings: 66 MHz - 4:1 ratio CCB clocks:SYSCLK - 3:1 ration e500 Core:CCB - pos1 - on, pos2 - on, pos3 - off, pos4 - on, pos5 - off, pos6 - on - Note: SW9 Settings: 33 MHz - 8:1 ratio CCB clocks:SYSCLK - 3:1 ration e500 Core:CCB - pos1 - on, pos2 - on, pos3 - on, pos4 - off, pos5 - off, pos6 - on - - -Flashing the FLASH device with the "Wind River ICE": - -1) Properly connect and configure the Wind River ICE to the target - JTAG port. This includes running the SBC8560 register script. Make - sure target memory can be read and written. - -2) Build the u-boot image: - make distclean - make SBC8560_66_config or SBC8560_33_config - make CROSS_COMPILE=.../ELDK3.0/ppc_8xx-/ all - - Note: reference is made to the ELDK3.0 compiler. Further, it seems - the ppc_8xx compiler is required for the 85xx (no 85xx - designated compiler in ELDK3.0) - -3) Convert the uboot (.elf) file to a uboot.bin file (using - visionClick converter). The bin file should be converted from - fffc0000 to ffffffff - -4) Setup the Flash Utility (tools menu) for: - - Do a "dc clr" [visionClick] to load the default register settings - Determine the clock speed of the PCI bus and set SW9 accordingly - Note: the speed of the PCI bus defaults to the slowest PCI card - PlayBack the "default" register file for the SBC8560 - Select the uboot.bin file with zero bias - Select the initialize Target prior to programming - Select the V28F640Jx (8192 x 8) 1 device FLASH Algorithm - Select the erase base address from FFFC0000 to FFFFFFFF - Select the start address from 0 with size of 4000 - -5) Erase and Program diff --git a/board/sbc8560/ddr.c b/board/sbc8560/ddr.c deleted file mode 100644 index e9babc6477..0000000000 --- a/board/sbc8560/ddr.c +++ /dev/null @@ -1,43 +0,0 @@ -/* - * Copyright 2008 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * Version 2 as published by the Free Software Foundation. - */ - -#include - -#include -#include - -void fsl_ddr_board_options(memctl_options_t *popts, - dimm_params_t *pdimm, - unsigned int ctrl_num) -{ - /* - * Factors to consider for CPO: - * - frequency - * - ddr1 vs. ddr2 - */ - popts->cpo_override = 0; - - /* - * Factors to consider for write data delay: - * - number of DIMMs - * - * 1 = 1/4 clock delay - * 2 = 1/2 clock delay - * 3 = 3/4 clock delay - * 4 = 1 clock delay - * 5 = 5/4 clock delay - * 6 = 3/2 clock delay - */ - popts->write_data_delay = 3; - - /* - * Factors to consider for half-strength driver enable: - * - number of DIMMs installed - */ - popts->half_strength_driver_enable = 0; -} diff --git a/board/sbc8560/law.c b/board/sbc8560/law.c deleted file mode 100644 index 4e6baed2f4..0000000000 --- a/board/sbc8560/law.c +++ /dev/null @@ -1,60 +0,0 @@ -/* - * Copyright 2008 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include - -/* LAW(Local Access Window) configuration: - * 0000_0000-0800_0000: DDR(512M) -or- larger - * c000_0000-cfff_ffff: PCI(256M) - * d000_0000-dfff_ffff: RapidIO(256M) - * e000_0000-ffff_ffff: localbus(512M) - * e000_0000-e3ff_ffff: LBC 64M, 32-bit flash on CS6 - * e400_0000-e7ff_ffff: LBC 64M, 32-bit flash on CS1 - * e800_0000-efff_ffff: LBC 128M, nothing here - * f000_0000-f3ff_ffff: LBC 64M, SDRAM on CS3 - * f400_0000-f7ff_ffff: LBC 64M, SDRAM on CS4 - * f800_0000-fdff_ffff: LBC 64M, nothing here - * fc00_0000-fcff_ffff: LBC 16M, CSR,RTC,UART,etc on CS5 - * fd00_0000-fdff_ffff: LBC 16M, nothing here - * fe00_0000-feff_ffff: LBC 16M, nothing here - * ff00_0000-ff6f_ffff: LBC 7M, nothing here - * ff70_0000-ff7f_ffff: CCSRBAR 1M - * ff80_0000-ffff_ffff: LBC 8M, 8-bit flash on CS0 - * Note: CCSRBAR and L2-as-SRAM don't need configure Local Access - * Window. - * Note: If flash is 8M at default position(last 8M),no LAW needed. - */ - -struct law_entry law_table[] = { -#ifndef CONFIG_SPD_EEPROM - SET_LAW(CONFIG_SYS_DDR_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_DDR), -#endif - SET_LAW(CONFIG_SYS_PCI_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCI), - SET_LAW(CONFIG_SYS_LBC_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_LBC), -}; - -int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/sbc8560/sbc8560.c b/board/sbc8560/sbc8560.c deleted file mode 100644 index 98bc7df4c8..0000000000 --- a/board/sbc8560/sbc8560.c +++ /dev/null @@ -1,369 +0,0 @@ -/* - * (C) Copyright 2003,Motorola Inc. - * Xianghua Xiao, (X.Xiao@motorola.com) - * - * (C) Copyright 2002 Scott McNutt - * - * (C) Copyright 2004 Wind River Systems Inc . - * Added support for Wind River SBC8560 board - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */ - /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */ - /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */ - /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */ - /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */ - /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */ - /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ - /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ - /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ - /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ - /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ - /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ - /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ - /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ - /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */ - /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */ - /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */ - /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */ - /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */ - /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */ - /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */ - /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */ - /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */ - /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */ - /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ - /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */ - /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ - /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ - /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ - /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ - /* PA1 */ { 1, 0, 0, 0, 0, 0 }, /* FREERUN */ - /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ - }, - - /* Port B configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ - /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ - /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ - /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ - /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ - /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ - /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ - /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ - /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ - /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ - /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ - /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ - /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ - /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ - /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */ - /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */ - /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */ - /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */ - /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */ - /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */ - /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - /* Port C */ - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ - /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */ - /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ - /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ - /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */ - /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ - /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ - /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ - /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ - /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ - /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ - /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ - /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */ - /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */ - /* PC17 */ { 0, 0, 0, 1, 0, 0 }, /* PC17 */ - /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */ - /* PC15 */ { 1, 1, 0, 0, 0, 0 }, /* PC15 */ - /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ - /* PC13 */ { 0, 0, 0, 1, 0, 0 }, /* PC13 */ - /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */ - /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */ - /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FETHMDC */ - /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* FETHMDIO */ - /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ - /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ - /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ - /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */ - /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */ - /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ - /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */ - /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */ - /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */ - }, - - /* Port D */ - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ - /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ - /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 RTS */ - /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* SCC2 RxD */ - /* PD27 */ { 1, 1, 1, 1, 0, 0 }, /* SCC2 TxD */ - /* PD26 */ { 1, 1, 0, 1, 0, 0 }, /* SCC2 RTS */ - /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ - /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ - /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ - /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ - /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ - /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ - /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ - /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ - /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ - /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */ - /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ - /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ - /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ - /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ - /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ - /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ - /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ - /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ - /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */ - /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - -int board_early_init_f (void) -{ -#if defined(CONFIG_PCI) - volatile ccsr_pcix_t *pci = (void *)(CONFIG_SYS_MPC85xx_PCIX_ADDR); - - pci->peer &= 0xfffffffdf; /* disable master abort */ -#endif - return 0; -} - -void reset_phy (void) -{ -#if defined(CONFIG_ETHER_ON_FCC) /* avoid compile warnings for now */ - volatile unsigned char *bcsr = (unsigned char *) CONFIG_SYS_BCSR; -#endif - /* reset Giga bit Ethernet port if needed here */ - - /* reset the CPM FEC port */ -#if (CONFIG_ETHER_INDEX == 2) - bcsr[0] &= ~0x20; - udelay(2); - bcsr[0] |= 0x20; - udelay(1000); -#elif (CONFIG_ETHER_INDEX == 3) - bcsr[0] &= ~0x10; - udelay(2); - bcsr[0] |= 0x10; - udelay(1000); -#endif -#if defined(CONFIG_MII) && defined(CONFIG_ETHER_ON_FCC) - /* reset PHY */ - miiphy_reset("FCC1", 0x0); - - /* change PHY address to 0x02 */ - bb_miiphy_write(NULL, 0, MII_MIPSCR, 0xf028); - - bb_miiphy_write(NULL, 0x02, MII_BMCR, - BMCR_ANENABLE | BMCR_ANRESTART); -#endif /* CONFIG_MII */ -} - -int checkboard (void) -{ - sys_info_t sysinfo; - char buf[32]; - - get_sys_info (&sysinfo); - -#ifdef CONFIG_SBC8560 - printf ("Board: Wind River SBC8560 Board\n"); -#else - printf ("Board: Wind River SBC8540 Board\n"); -#endif - printf ("\tCPU: %s MHz\n", strmhz(buf, sysinfo.freqProcessor[0])); - printf ("\tCCB: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus)); - printf ("\tDDR: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus/2)); - if((CONFIG_SYS_LBC_LCRR & 0x0f) == 2 || (CONFIG_SYS_LBC_LCRR & 0x0f) == 4 \ - || (CONFIG_SYS_LBC_LCRR & 0x0f) == 8) { - printf ("\tLBC: %s MHz\n", - strmhz(buf, sysinfo.freqSystemBus/(CONFIG_SYS_LBC_LCRR & 0x0f))); - } else { - printf("\tLBC: unknown\n"); - } - printf("\tCPM: %s MHz\n", strmhz(buf, sysinfo.freqSystemBus)); - printf("L1 D-cache 32KB, L1 I-cache 32KB enabled.\n"); - return (0); -} - - -#if defined(CONFIG_SYS_DRAM_TEST) -int testdram (void) -{ - uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START; - uint *pend = (uint *) CONFIG_SYS_MEMTEST_END; - uint *p; - - printf("SDRAM test phase 1:\n"); - for (p = pstart; p < pend; p++) - *p = 0xaaaaaaaa; - - for (p = pstart; p < pend; p++) { - if (*p != 0xaaaaaaaa) { - printf ("SDRAM test fails at: %08x\n", (uint) p); - return 1; - } - } - - printf("SDRAM test phase 2:\n"); - for (p = pstart; p < pend; p++) - *p = 0x55555555; - - for (p = pstart; p < pend; p++) { - if (*p != 0x55555555) { - printf ("SDRAM test fails at: %08x\n", (uint) p); - return 1; - } - } - - printf("SDRAM test passed.\n"); - return 0; -} -#endif - -#if !defined(CONFIG_SPD_EEPROM) -/************************************************************************* - * fixed sdram init -- doesn't use serial presence detect. - ************************************************************************/ -phys_size_t fixed_sdram(void) -{ - -#define CONFIG_SYS_DDR_CONTROL 0xc2000000 - - #ifndef CONFIG_SYS_RAMBOOT - volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR); - -#if (CONFIG_SYS_SDRAM_SIZE == 512) - ddr->cs0_bnds = 0x0000000f; -#else - ddr->cs0_bnds = 0x00000007; -#endif - ddr->cs1_bnds = 0x0010001f; - ddr->cs2_bnds = 0x00000000; - ddr->cs3_bnds = 0x00000000; - ddr->cs0_config = 0x80000102; - ddr->cs1_config = 0x80000102; - ddr->cs2_config = 0x00000000; - ddr->cs3_config = 0x00000000; - ddr->timing_cfg_1 = 0x37334321; - ddr->timing_cfg_2 = 0x00000800; - ddr->sdram_cfg = 0x42000000; - ddr->sdram_mode = 0x00000022; - ddr->sdram_interval = 0x05200100; - ddr->err_sbe = 0x00ff0000; - #if defined (CONFIG_DDR_ECC) - ddr->err_disable = 0x0000000D; - #endif - asm("sync;isync;msync"); - udelay(500); - #if defined (CONFIG_DDR_ECC) - /* Enable ECC checking */ - ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000); - #else - ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL; - #endif - asm("sync; isync; msync"); - udelay(500); - #endif - return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; -} -#endif /* !defined(CONFIG_SPD_EEPROM) */ - - -#if defined(CONFIG_OF_BOARD_SETUP) -void -ft_board_setup(void *blob, bd_t *bd) -{ - int node; -#ifdef CONFIG_PCI - const char *path; -#endif - - ft_cpu_setup(blob, bd); - - node = fdt_path_offset(blob, "/aliases"); - if (node >= 0) { -#ifdef CONFIG_PCI - path = fdt_getprop(blob, node, "pci0", NULL); - if (path) { - tmp[1] = hose.last_busno - hose.first_busno; - do_fixup_by_path(blob, path, "bus-range", &tmp, 8, 1); - } -#endif - } -} -#endif diff --git a/board/sbc8560/tlb.c b/board/sbc8560/tlb.c deleted file mode 100644 index fe0ac763af..0000000000 --- a/board/sbc8560/tlb.c +++ /dev/null @@ -1,65 +0,0 @@ -/* - * Copyright 2008 Freescale Semiconductor, Inc. - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include - -struct fsl_e_tlb_entry tlb_table[] = { -/* TLB for CCSRBAR (IMMR) */ - SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 1, BOOKE_PAGESZ_1M, 1), - -/* TLB for Local Bus stuff, just map the whole 512M */ -/* note that the LBC SDRAM is cache-inhibit and guarded, like everything else */ - - SET_TLB_ENTRY(1, 0xe0000000, 0xe0000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 2, BOOKE_PAGESZ_256M, 1), - - SET_TLB_ENTRY(1, 0xf0000000, 0xf0000000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 3, BOOKE_PAGESZ_256M, 1), - -#if !defined(CONFIG_SPD_EEPROM) - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 4, BOOKE_PAGESZ_256M, 1), - - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 5, BOOKE_PAGESZ_256M, 1), -#endif - - SET_TLB_ENTRY(1, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 6, BOOKE_PAGESZ_16K, 1), - - SET_TLB_ENTRY(1, CONFIG_SYS_PCI_MEM_PHYS, CONFIG_SYS_PCI_MEM_PHYS, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 7, BOOKE_PAGESZ_256M, 1), -}; - -int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/boards.cfg b/boards.cfg index a5af63c1ba..df62251253 100644 --- a/boards.cfg +++ b/boards.cfg @@ -682,17 +682,11 @@ suvd3 powerpc mpc83xx km83xx keymile tuge1 powerpc mpc83xx km83xx keymile - tuxx1:KM_DISABLE_APP2,TUGE1 tuxx1 powerpc mpc83xx km83xx keymile kmsupx5 powerpc mpc83xx km83xx keymile - tuxx1:KM_DISABLE_APP2,KMSUPX5 -sbc8540 powerpc mpc85xx sbc8560 - - SBC8540 -sbc8540_33 powerpc mpc85xx sbc8560 - - SBC8540 -sbc8540_66 powerpc mpc85xx sbc8560 - - SBC8540 sbc8548 powerpc mpc85xx sbc8548 - - sbc8548 sbc8548_PCI_33 powerpc mpc85xx sbc8548 - - sbc8548:PCI,33 sbc8548_PCI_33_PCIE powerpc mpc85xx sbc8548 - - sbc8548:PCI,33,PCIE sbc8548_PCI_66 powerpc mpc85xx sbc8548 - - sbc8548:PCI,66 sbc8548_PCI_66_PCIE powerpc mpc85xx sbc8548 - - sbc8548:PCI,66,PCIE -sbc8560 powerpc mpc85xx sbc8560 - - sbc8560 -sbc8560_33 powerpc mpc85xx sbc8560 - - sbc8560 -sbc8560_66 powerpc mpc85xx sbc8560 - - sbc8560 socrates powerpc mpc85xx socrates HWW1U1A powerpc mpc85xx hww1u1a exmeritus MPC8536DS powerpc mpc85xx mpc8536ds freescale - MPC8536DS diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h deleted file mode 100644 index d448bf6650..0000000000 --- a/include/configs/SBC8540.h +++ /dev/null @@ -1,428 +0,0 @@ -/* - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao - * - * (C) Copyright 2004 Wind River Systems Inc . - * Added support for Wind River SBC8540 board - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * sbc8540 board configuration file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Top level Makefile configuration choices - */ -#ifdef CONFIG_66 -#define CONFIG_PCI_66 -#endif - -#define TSEC_DEBUG - -/* - * High Level Configuration Options - */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ -#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */ - -#define CONFIG_SYS_TEXT_BASE 0xfffc0000 - - -#define CONFIG_CPM2 1 /* has CPM2 */ - -#define CONFIG_SBC8540 1 /* configuration for SBC8560 board */ -#define CONFIG_MPC8540 1 - -#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific (supplement) */ - -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#undef CONFIG_PCI /* pci ethernet support */ -#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ - -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ - -#define CONFIG_ENV_OVERWRITE - -/* Using Localbus SDRAM to emulate flash before we can program the flash, - * normally you need a flash-boot image(u-boot.bin), if so undef this. - */ -#undef CONFIG_RAM_AS_FLASH - -#if defined(CONFIG_PCI_66) /* some PCI card is 33Mhz only */ - #define CONFIG_SYS_CLK_FREQ 66000000 /* sysclk for MPC85xx */ -#else - #define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */ -#endif - -/* below can be toggled for performance analysis. otherwise use default */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#undef CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - -#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \ - defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \ - defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC)) -#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC." -#endif - -#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ - -/* DDR Setup */ -#define CONFIG_FSL_DDR1 -#undef CONFIG_FSL_DDR_INTERACTIVE -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#undef CONFIG_DDR_SPD - -#if defined(CONFIG_MPC85xx_REV1) -#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */ -#endif - -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x55 /* CTLR 0 DIMM 0 */ - -#undef CONFIG_CLOCKS_IN_MHZ - -#if defined(CONFIG_RAM_AS_FLASH) - #define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ - #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 8M */ - #define CONFIG_SYS_BR0_PRELIM 0xf8000801 /* port size 8bit */ - #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */ -#else /* Boot from real Flash */ - #define CONFIG_SYS_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */ - #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ - #define CONFIG_SYS_BR0_PRELIM 0xff800801 /* port size 8bit */ - #define CONFIG_SYS_OR0_PRELIM 0xff800ff7 /* 8MB Flash */ -#endif -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -/* local bus definitions */ -#define CONFIG_SYS_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */ -#define CONFIG_SYS_OR1_PRELIM 0xfc000ff7 - -#define CONFIG_SYS_BR2_PRELIM 0x00000000 /* CS2 not used */ -#define CONFIG_SYS_OR2_PRELIM 0x00000000 - -#define CONFIG_SYS_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */ -#define CONFIG_SYS_OR3_PRELIM 0xfc000cc1 - -#if defined(CONFIG_RAM_AS_FLASH) - #define CONFIG_SYS_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */ -#else - #define CONFIG_SYS_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */ -#endif -#define CONFIG_SYS_OR4_PRELIM 0xfc000cc1 - -#define CONFIG_SYS_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */ -#if 1 - #define CONFIG_SYS_OR5_PRELIM 0xff000ff7 -#else - #define CONFIG_SYS_OR5_PRELIM 0xff0000f0 -#endif - -#define CONFIG_SYS_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */ -#define CONFIG_SYS_OR6_PRELIM 0xfc000ff7 -#define CONFIG_SYS_LBC_LCRR 0x00030002 /* local bus freq */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 -#define CONFIG_SYS_LBC_LSRT 0x20000000 -#define CONFIG_SYS_LBC_MRTPR 0x20000000 -#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 -#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 -#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 -#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 -#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 - -/* just hijack the MOT BCSR def for SBC8560 misc devices */ -#define CONFIG_SYS_BCSR ((CONFIG_SYS_BR5_PRELIM & 0xff000000)|0x00400000) -/* the size of CS5 needs to be >= 16M for TLB and LAW setups */ - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#if 0 -#define CONFIG_SYS_NS16550_CLK 1843200 /* get_bus_freq(0) */ -#else -#define CONFIG_SYS_NS16550_CLK 264000000 /* get_bus_freq(0) */ -#endif - -#define CONFIG_BAUDRATE 9600 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#if 0 -#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00700000) -#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00800000) -#else -/* SBC8540 uses internal COMM controller */ -#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_CCSRBAR & 0xfff00000)+0x00004500) -#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_CCSRBAR & 0xfff00000)+0x00004600) -#endif - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * I2C - */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 - -#define CONFIG_SYS_PCI_MEM_BASE 0xC0000000 -#define CONFIG_SYS_PCI_MEM_PHYS 0xC0000000 -#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 - -#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ - -# define CONFIG_MPC85xx_TSEC1 -# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" -# define CONFIG_MII 1 /* MII PHY management */ -# define TSEC1_PHY_ADDR 25 -# define TSEC1_PHYIDX 0 -/* Options are: TSEC0 */ -# define CONFIG_ETHPRIME "TSEC0" - - -#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ - - #undef CONFIG_ETHER_NONE /* define if ether on something else */ - #define CONFIG_ETHER_ON_FCC2 /* cpm FCC ethernet support */ - #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ - - #if (CONFIG_ETHER_INDEX == 2) - /* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers - * - Full duplex - */ - #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) - #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) - #define CONFIG_SYS_CPMFCR_RAMTYPE 0 - #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) - - #elif (CONFIG_ETHER_INDEX == 3) - /* need more definitions here for FE3 */ - #endif /* CONFIG_ETHER_INDEX */ - - #define CONFIG_MII /* MII PHY management */ - #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ - /* - * GPIO pins used for bit-banged MII communications - */ - #define MDIO_PORT 2 /* Port C */ - #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ - (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) - #define MDC_DECLARE MDIO_DECLARE - - #define MDIO_ACTIVE (iop->pdir |= 0x00400000) - #define MDIO_TRISTATE (iop->pdir &= ~0x00400000) - #define MDIO_READ ((iop->pdat & 0x00400000) != 0) - - #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 - - #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 - - #define MIIDELAY udelay(1) - -#endif - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#if 0 -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */ -#endif -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if 0 -/* XXX This doesn't work and I don't want to fix it */ -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) - #define CONFIG_SYS_RAMBOOT -#else - #undef CONFIG_SYS_RAMBOOT -#endif -#endif - -/* Environment */ -#if !defined(CONFIG_SYS_RAMBOOT) - #if defined(CONFIG_RAM_AS_FLASH) - #define CONFIG_ENV_IS_NOWHERE - #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000) - #define CONFIG_ENV_SIZE 0x2000 - #else - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) - #define CONFIG_ENV_SIZE 0x2000 /* CONFIG_ENV_SECT_SIZE */ - #endif -#else - #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ - #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600" -/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/ -#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000" -#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI -#endif - -#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_CMD_MII -#endif - -#if defined(CONFIG_SYS_RAMBOOT) - #undef CONFIG_CMD_SAVEENV - #undef CONFIG_CMD_LOADS -#endif - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "SBC8540=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ - #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/*Note: change below for your network setting!!! */ -#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -# define CONFIG_ETHADDR 00:vv:ww:xx:yy:8a -# define CONFIG_HAS_ETH1 -# define CONFIG_ETH1ADDR 00:vv:ww:xx:yy:8b -# define CONFIG_HAS_ETH2 -# define CONFIG_ETH2ADDR 00:vv:ww:xx:yy:8c -#endif - -#define CONFIG_SERVERIP YourServerIP -#define CONFIG_IPADDR YourTargetIP -#define CONFIG_GATEWAYIP YourGatewayIP -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_HOSTNAME SBC8560 -#define CONFIG_ROOTPATH "YourRootPath" -#define CONFIG_BOOTFILE "YourImageName" - -#endif /* __CONFIG_H */ diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h deleted file mode 100644 index 46d60985d3..0000000000 --- a/include/configs/sbc8560.h +++ /dev/null @@ -1,459 +0,0 @@ -/* - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao - * - * (C) Copyright 2004 Wind River Systems Inc . - * Added support for Wind River SBC8560 board - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * sbc8560 board configuration file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Top level Makefile configuration choices - */ -#ifdef CONFIG_66 -#define CONFIG_PCI_66 -#endif - -/* - * High Level Configuration Options - */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ -#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */ - -#define CONFIG_SYS_TEXT_BASE 0xfffc0000 - - -#define CONFIG_CPM2 1 /* has CPM2 */ -#define CONFIG_SBC8560 1 /* configuration for SBC8560 board */ -#define CONFIG_MPC8560 1 - -/* XXX flagging this as something I might want to delete */ -#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */ - -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#undef CONFIG_PCI /* pci ethernet support */ -#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ - -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ - -#define CONFIG_ENV_OVERWRITE - -/* Using Localbus SDRAM to emulate flash before we can program the flash, - * normally you need a flash-boot image(u-boot.bin), if so undef this. - */ -#undef CONFIG_RAM_AS_FLASH - -#if defined(CONFIG_PCI_66) /* some PCI card is 33Mhz only */ - #define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */ -#else - #define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */ -#endif - -/* below can be toggled for performance analysis. otherwise use default */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#undef CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - -#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \ - defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \ - defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC)) -#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC." -#endif - -#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ - -/* DDR Setup */ -#define CONFIG_FSL_DDR1 -#undef CONFIG_FSL_DDR_INTERACTIVE -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#undef CONFIG_DDR_SPD - -#if defined(CONFIG_MPC85xx_REV1) -#define CONFIG_SYS_FSL_ERRATUM_DDR_MSYNC_IN /* possible DLL fix needed */ -#endif - -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x55 /* CTLR 0 DIMM 0 */ - -#undef CONFIG_CLOCKS_IN_MHZ - -#if defined(CONFIG_RAM_AS_FLASH) - #define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ - #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 8M */ - #define CONFIG_SYS_BR0_PRELIM 0xf8000801 /* port size 8bit */ - #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */ -#else /* Boot from real Flash */ - #define CONFIG_SYS_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */ - #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */ - #define CONFIG_SYS_BR0_PRELIM 0xff800801 /* port size 8bit */ - #define CONFIG_SYS_OR0_PRELIM 0xff800ff7 /* 8MB Flash */ -#endif -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -/* local bus definitions */ -#define CONFIG_SYS_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */ -#define CONFIG_SYS_OR1_PRELIM 0xfc000ff7 - -#define CONFIG_SYS_BR2_PRELIM 0x00000000 /* CS2 not used */ -#define CONFIG_SYS_OR2_PRELIM 0x00000000 - -#define CONFIG_SYS_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */ -#define CONFIG_SYS_OR3_PRELIM 0xfc000cc1 - -#if defined(CONFIG_RAM_AS_FLASH) - #define CONFIG_SYS_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */ -#else - #define CONFIG_SYS_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */ -#endif -#define CONFIG_SYS_OR4_PRELIM 0xfc000cc1 - -#define CONFIG_SYS_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */ -#if 1 - #define CONFIG_SYS_OR5_PRELIM 0xff000ff7 -#else - #define CONFIG_SYS_OR5_PRELIM 0xff0000f0 -#endif - -#define CONFIG_SYS_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */ -#define CONFIG_SYS_OR6_PRELIM 0xfc000ff7 -#define CONFIG_SYS_LBC_LCRR 0x00030002 /* local bus freq */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 -#define CONFIG_SYS_LBC_LSRT 0x20000000 -#define CONFIG_SYS_LBC_MRTPR 0x20000000 -#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 -#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 -#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 -#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 -#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 - -/* just hijack the MOT BCSR def for SBC8560 misc devices */ -#define CONFIG_SYS_BCSR ((CONFIG_SYS_BR5_PRELIM & 0xff000000)|0x00400000) -/* the size of CS5 needs to be >= 16M for TLB and LAW setups */ - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK 1843200 /* get_bus_freq(0) */ -#define CONFIG_BAUDRATE 9600 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00700000) -#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00800000) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* - * I2C - */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CONFIG_SYS_I2C_OFFSET 0x3000 - -#define CONFIG_SYS_PCI_MEM_BASE 0xC0000000 -#define CONFIG_SYS_PCI_MEM_PHYS 0xC0000000 -#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 - -#ifdef CONFIG_TSEC_ENET - -#ifndef CONFIG_MII -#define CONFIG_MII 1 /* MII PHY management */ -#endif -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 0x19 -#define TSEC2_PHY_ADDR 0x1a -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ - - #undef CONFIG_ETHER_NONE /* define if ether on something else */ - #define CONFIG_ETHER_ON_FCC2 /* cpm FCC ethernet support */ - #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ - - #if (CONFIG_ETHER_INDEX == 2) - /* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers - * - Full duplex - */ - #define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) - #define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) - #define CONFIG_SYS_CPMFCR_RAMTYPE 0 - #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) - - #elif (CONFIG_ETHER_INDEX == 3) - /* need more definitions here for FE3 */ - #endif /* CONFIG_ETHER_INDEX */ - - #define CONFIG_MII /* MII PHY management */ - #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ - /* - * GPIO pins used for bit-banged MII communications - */ - #define MDIO_PORT 2 /* Port C */ - #define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ - (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) - #define MDC_DECLARE MDIO_DECLARE - - #define MDIO_ACTIVE (iop->pdir |= 0x00400000) - #define MDIO_TRISTATE (iop->pdir &= ~0x00400000) - #define MDIO_READ ((iop->pdat & 0x00400000) != 0) - - #define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 - - #define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 - - #define MIIDELAY udelay(1) - -#endif - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#if 0 -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */ -#endif -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if 0 -/* XXX This doesn't work and I don't want to fix it */ -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) - #define CONFIG_SYS_RAMBOOT -#else - #undef CONFIG_SYS_RAMBOOT -#endif -#endif - -/* Environment */ -#if !defined(CONFIG_SYS_RAMBOOT) - #if defined(CONFIG_RAM_AS_FLASH) - #define CONFIG_ENV_IS_NOWHERE - #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000) - #define CONFIG_ENV_SIZE 0x2000 - #else - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) - #define CONFIG_ENV_SIZE 0x2000 /* CONFIG_ENV_SECT_SIZE */ - #endif -#else - #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ - #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=dhcp console=ttyS0,9600" -/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/ -#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI -#endif - -#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) - #define CONFIG_CMD_MII -#endif - -#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) - #undef CONFIG_CMD_SAVEENV - #undef CONFIG_CMD_LOADS -#endif - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "SBC8560=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -/* You can compile in a MAC address and your custom net settings by using - * the following syntax. Your board should be marked with the assigned - * MAC addresses directly on it. - * - * #define CONFIG_ETHADDR de:ad:be:ef:00:00 - * #define CONFIG_ETH1ADDR fa:ke:ad:dr:es:s! - * #define CONFIG_SERVERIP - * #define CONFIG_IPADDR - * #define CONFIG_GATEWAYIP - * #define CONFIG_NETMASK - */ - -#define CONFIG_HOSTNAME SBC8560 -#define CONFIG_ROOTPATH "/home/ppc" -#define CONFIG_BOOTFILE "uImage" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=ramdisk.uboot\0" \ - "fdtaddr=c00000\0" \ - "fdtfile=sbc8560.dtb\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */ -- 2.25.1