From 0b62fe5ed87ecac52301096b15abb69f96117c8c Mon Sep 17 00:00:00 2001 From: Mathias Kresin Date: Fri, 9 Jun 2017 19:28:36 +0200 Subject: [PATCH] lantiq: complete AVM FRITZ!Box 3370 support Rename the image and use a compatible string which indicates that only hardware revision 2 and higher is supported. It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO. The HWREV can be checked by connecting to the fritzbox right after power on via ftp: ftp> quote GETENV HWSubRevision Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash chips are used. Usually it isn't a big deal but depending on the used NAND flash chip, the ECC calculation is done different (and incompatible of course). Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND flash chip are doing the ECC calculation in software. Supporting both with a single DTS isn't possible. It might be possible to add a patch selecting the ECC mode dynamicaly based on the found NAND flash chip. But such a patch has no chance to get accepted upstream and most likely need to be touched with every kernel update. Instead two images are created. One for Micron NAND flash chip and one for Hynix NAND flash chip. So far no pattern is known to identify the used flash chip without opening the box. Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as input, which will cause a reboot 30sec after power on. For boards with EVA version 2186 the installation is tricky as it has to be finished within the 30sec time frame. The EVA version can be checked by connecting to the fritzbox right after power on via ftp: ftp> quote GETENV urlader-version The ath9k eeprom/caldata is at a different and offset and stored in reverse order (from the last byte to the beginning) on the flash. Reverse the bits to bring the data into the format expected by the ath9k driver. Since the ath9k eeprom is stored in reverse order on flash, we can not use the mac address from the on flash eeprom. Get the MAC address from the tffs instead. Within the same HW revision 5 of the Fritz!Box 3370 both version of the vr9 SoC are used. During preparation of kernel 4.14 support, all devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2 gphy firmware, which fixed the embedded phys for boards using the version 1.2 of the vr9 SoC. While at it, add a trigger to make use of the LAN LED. Setup the build-in switch and add a hint for LuCI two show the ports in order matching the labels on the case Add support for the second USB port and provide the volatage GPIOs. Use GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38. Name the rootfs partition ubi and remove the mtd/rootfs related kernel bootargs to use the OpenWrt autoprobing based on the partition name. Enable sysupgrade support to allow an upgrade from a running system. Since sysupgrade wasn't supported till now, drop image build code which was added to allow a sysupgrade from earlier OpenWrt versions. Build images that allow an (initial) installation via EVA bootloader. To install OpenWrt via Eva bootloader, within the first seconds after power on a ftp connection need to be established to the FRITZ!Box at 192.168.178.1 and the the following ftp commands need to be run: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote SETENV linux_fs_start 0 ftp> quote MEDIA FLSH ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1 ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0 Signed-off-by: Andrea Merello Signed-off-by: Mathias Kresin --- .../lantiq/base-files/etc/board.d/01_leds | 4 + .../lantiq/base-files/etc/board.d/02_network | 9 +- .../etc/hotplug.d/firmware/12-ath9k-eeprom | 24 +++- .../lantiq/base-files/lib/upgrade/platform.sh | 8 +- .../mips/boot/dts/FRITZ3370-REV2-HYNIX.dts | 55 ++++++++ .../mips/boot/dts/FRITZ3370-REV2-MICRON.dts | 53 +++++++ .../{FRITZ3370.dts => FRITZ3370-REV2.dtsi} | 129 ++++++++++-------- target/linux/lantiq/image/Makefile | 26 +++- 8 files changed, 238 insertions(+), 70 deletions(-) create mode 100644 target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts create mode 100644 target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts rename target/linux/lantiq/files-4.14/arch/mips/boot/dts/{FRITZ3370.dts => FRITZ3370-REV2.dtsi} (78%) diff --git a/target/linux/lantiq/base-files/etc/board.d/01_leds b/target/linux/lantiq/base-files/etc/board.d/01_leds index 0426fb18e6..4476a7eb43 100755 --- a/target/linux/lantiq/base-files/etc/board.d/01_leds +++ b/target/linux/lantiq/base-files/etc/board.d/01_leds @@ -53,6 +53,10 @@ bt,homehub-v5a) netgear,dm200) ucidef_set_led_netdev "lan" "lan" "dm200:green:lan" "eth0" ;; +avm,fritz3370-rev2-hynix|\ +avm,fritz3370-rev2-micron) + ucidef_set_led_switch "lan" "LAN" "fritz3370:green:lan" "switch0" "0x17" + ;; avm,fritz7320) ucidef_set_led_netdev "wifi" "wifi" "fritz7320:green:wlan" "wlan0" ;; diff --git a/target/linux/lantiq/base-files/etc/board.d/02_network b/target/linux/lantiq/base-files/etc/board.d/02_network index ca974b071e..9da01d14cc 100755 --- a/target/linux/lantiq/base-files/etc/board.d/02_network +++ b/target/linux/lantiq/base-files/etc/board.d/02_network @@ -135,10 +135,13 @@ lantiq,easy80920-nand|lantiq,easy80920-nor) "0:lan:4" "1:lan:3" "2:lan:2" "4:lan:1" "5:wan:5" "6t@eth0" ;; -avm,fritz3370) +avm,fritz3370-rev2-hynix|\ +avm,fritz3370-rev2-micron) annex="b" - wan_mac=$(macaddr_add "$(mtd_get_mac_binary urlader 2439)" 1) - ucidef_set_interface_lan 'eth0' + lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)")) + wan_mac=$(macaddr_add "$lan_mac" 3) + ucidef_add_switch "switch0" \ + "0:lan:3" "1:lan:4" "2:lan:2" "4:lan:1" "6t@eth0" ;; avm,fritz7320) diff --git a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom index 498a509012..75b763076e 100644 --- a/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom +++ b/target/linux/lantiq/base-files/etc/hotplug.d/firmware/12-ath9k-eeprom @@ -47,6 +47,24 @@ ath9k_eeprom_extract_raw() { ath9k_eeprom_die "failed to extract from $mtd" } +ath9k_eeprom_extract_reverse() { + local part=$1 + local offset=$2 + local count=$3 + local mtd + local reversed + local caldata + + mtd=$(find_mtd_chardev "$part") + reversed=$(hexdump -v -s $offset -n $count -e '/1 "%02x "' $mtd) + + for byte in $reversed; do + caldata="\x${byte}${caldata}" + done + + printf "%b" "$caldata" > /lib/firmware/$FIRMWARE +} + ath9k_eeprom_extract() { local part=$1 local offset=$2 @@ -138,7 +156,11 @@ case "$FIRMWARE" in ath9k_eeprom_extract "calibration" 61440 0 ath9k_patch_fw_mac_crc $(macaddr_add $(mtd_get_mac_ascii uboot-env ethaddr) +2) 524 ;; - avm,fritz3370|avm,fritz7320|avm,fritz7360sl) + avm,fritz3370-rev2-hynix|\ + avm,fritz3370-rev2-micron) + ath9k_eeprom_extract_reverse "urlader" 5441 1088 + ;; + avm,fritz7320|avm,fritz7360sl) ath9k_eeprom_extract "urlader" 2437 0 ;; tplink,tdw8970|tplink,tdw8980) diff --git a/target/linux/lantiq/base-files/lib/upgrade/platform.sh b/target/linux/lantiq/base-files/lib/upgrade/platform.sh index 2e58cb799a..ecbb939e36 100755 --- a/target/linux/lantiq/base-files/lib/upgrade/platform.sh +++ b/target/linux/lantiq/base-files/lib/upgrade/platform.sh @@ -9,7 +9,13 @@ platform_do_upgrade() { local board=$(board_name) case "$board" in - bt,homehub-v2b|bt,homehub-v3a|bt,homehub-v5a|zyxel,p-2812hnu-f1|zyxel,p-2812hnu-f3) + avm,fritz3370-rev2-hynix|\ + avm,fritz3370-rev2-micron|\ + bt,homehub-v2b|\ + bt,homehub-v3a|\ + bt,homehub-v5a|\ + zyxel,p-2812hnu-f1|\ + zyxel,p-2812hnu-f3) nand_do_upgrade $1 ;; *) diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts new file mode 100644 index 0000000000..225a4f3e8a --- /dev/null +++ b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts @@ -0,0 +1,55 @@ +/dts-v1/; + +#include "FRITZ3370-REV2.dtsi" + +/ { + compatible = "avm,fritz3370-rev2-hynix", "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; + model = "AVM Fritz!Box WLAN 3370 Rev. 2 (Hynix NAND)"; +}; + +&localbus { + nand@1 { + compatible = "lantiq,nand-xway"; + bank-width = <2>; + reg = <1 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-mode = "soft"; + nand-ecc-strength = <3>; + nand-ecc-step-size = <256>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x3000000>; + }; + + partition@3400000 { + label = "reserved-kernel"; + reg = <0x3400000 0x400000>; + }; + partition@3800000 { + label = "reserved-filesystem"; + reg = <0x3800000 0x3000000>; + }; + partition@6800000 { + label = "config"; + reg = <0x6800000 0x200000>; + }; + partition@6a00000 { + label = "nand-filesystem"; + reg = <0x6a00000 0x1600000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts new file mode 100644 index 0000000000..3346310b1b --- /dev/null +++ b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts @@ -0,0 +1,53 @@ +/dts-v1/; + +#include "FRITZ3370-REV2.dtsi" + +/ { + compatible = "avm,fritz3370-rev2-micron", "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; + model = "AVM Fritz!Box WLAN 3370 Rev. 2 (Micron NAND)"; +}; + +&localbus { + nand@1 { + compatible = "lantiq,nand-xway"; + bank-width = <2>; + reg = <1 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-mode = "on-die"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x3000000>; + }; + + partition@3400000 { + label = "reserved-kernel"; + reg = <0x3400000 0x400000>; + }; + partition@3800000 { + label = "reserved-filesystem"; + reg = <0x3800000 0x3000000>; + }; + partition@6800000 { + label = "config"; + reg = <0x6800000 0x200000>; + }; + partition@6a00000 { + label = "nand-filesystem"; + reg = <0x6a00000 0x1600000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2.dtsi similarity index 78% rename from target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370.dts rename to target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2.dtsi index a958fc67aa..f6180c474f 100644 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370.dts +++ b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2.dtsi @@ -1,16 +1,14 @@ -/dts-v1/; - #include "vr9.dtsi" #include #include / { - compatible = "avm,fritz3370", "lantiq,xway", "lantiq,vr9"; - model = "Fritz!Box WLAN 3370"; + compatible = "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; + model = "AVM Fritz!Box WLAN 3370 Rev. 2"; chosen { - bootargs = "console=ttyLTQ0,115200 ubi.mtd=1,512 root=/dev/mtdblock9"; + bootargs = "console=ttyLTQ0,115200"; }; aliases { @@ -27,21 +25,28 @@ reg = <0x0 0x8000000>; }; + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; + }; + gpio-keys-polled { compatible = "gpio-keys-polled"; #address-cells = <1>; #size-cells = <0>; poll-interval = <100>; + power { label = "power"; gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; linux,code = ; }; -/* wifi { - label = "wifi"; + + wifi { + label = "wlan"; gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; - linux,code = ; - };*/ + linux,code = ; + }; }; gpio-leds { @@ -52,31 +57,61 @@ gpios = <&gpio 32 GPIO_ACTIVE_LOW>; default-state = "keep"; }; + power_red: power2 { label = "fritz3370:red:power"; gpios = <&gpio 33 GPIO_ACTIVE_LOW>; }; + info_red { label = "fritz3370:red:info"; gpios = <&gpio 34 GPIO_ACTIVE_LOW>; }; + wifi: wifi { label = "fritz3370:green:wlan"; gpios = <&gpio 35 GPIO_ACTIVE_LOW>; }; + dsl: dsl { label = "fritz3370:green:dsl"; gpios = <&gpio 36 GPIO_ACTIVE_LOW>; }; + lan { label = "fritz3370:green:lan"; gpios = <&gpio 38 GPIO_ACTIVE_LOW>; }; + info_green: info_green { label = "fritz3370:green:info"; gpios = <&gpio 47 GPIO_ACTIVE_LOW>; }; }; + + usb0_vbus: regulator-usb0-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB0_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usb1_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB1_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; }; ð0 { @@ -85,8 +120,6 @@ #address-cells = <1>; #size-cells = <0>; reg = <0>; - mtd-mac-address = <&urlader 0x987>; - mtd-mac-address-increment = <(-2)>; lantiq,switch; ethernet@0 { @@ -96,6 +129,7 @@ phy-handle = <&phy0>; gpios = <&gpio 37 GPIO_ACTIVE_HIGH>; }; + ethernet@1 { compatible = "lantiq,xrx200-pdi-port"; reg = <1>; @@ -103,13 +137,15 @@ phy-handle = <&phy1>; gpios = <&gpio 44 GPIO_ACTIVE_HIGH>; }; + ethernet@2 { compatible = "lantiq,xrx200-pdi-port"; reg = <2>; phy-mode = "gmii"; phy-handle = <&phy11>; }; - ethernet@3 { + + ethernet@4 { compatible = "lantiq,xrx200-pdi-port"; reg = <4>; phy-mode = "gmii"; @@ -127,14 +163,17 @@ reg = <0x0>; compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; }; + phy1: ethernet-phy@1 { reg = <0x1>; compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; }; + phy11: ethernet-phy@11 { reg = <0x11>; compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; }; + phy13: ethernet-phy@13 { reg = <0x13>; compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; @@ -159,29 +198,34 @@ lantiq,groups = "mdio"; lantiq,function = "mdio"; }; + nand { lantiq,groups = "nand cle", "nand ale", "nand rd", "nand cs1", "nand rdy"; lantiq,function = "ebu"; lantiq,pull = <1>; }; + phy-rst { lantiq,pins = "io37", "io44"; lantiq,pull = <0>; lantiq,open-drain = <0>; lantiq,output = <1>; }; + pcie-rst { - lantiq,pins = "io38"; + lantiq,pins = "io21"; lantiq,pull = <0>; lantiq,output = <1>; }; }; + pins_spi_default: pins_spi_default { spi_in { lantiq,groups = "spi_di"; lantiq,function = "spi"; }; + spi_out { lantiq,groups = "spi_do", "spi_clk", "spi_cs4"; @@ -191,50 +235,9 @@ }; }; -&localbus { - nand@1 { - compatible = "lantiq,nand-xway"; - bank-width = <2>; - reg = <1 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x0 0x400000>; - }; - - partition@400000 { - label = "rootfs_ubi"; - reg = <0x400000 0x3000000>; - }; - - partition@3400000 { - label = "vr9_firmware"; - reg = <0x3400000 0x400000>; - }; - partition@3800000 { - label = "reserved"; - reg = <0x3800000 0x3000000>; - }; - partition@6800000 { - label = "config"; - reg = <0x6800000 0x200000>; - }; - partition@6a00000 { - label = "nand-filesystem"; - reg = <0x6a00000 0x1600000>; - }; - }; - }; -}; - &pcie0 { + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + pcie@0 { reg = <0 0 0 0 0>; #interrupt-cells = <1>; @@ -283,14 +286,20 @@ }; }; -/* - * TODO: add phy-supply, gpio 5 GPIO_ACTIVE_HIGH and gpio 14 GPIO_ACTIVE_HIGH are - * related - */ &usb_phy0 { status = "okay"; + phy-supply = <&usb0_vbus>; +}; + +&usb_phy1 { + status = "okay"; + phy-supply = <&usb1_vbus>; }; &usb0 { status = "okay"; }; + +&usb1 { + status = "okay"; +}; diff --git a/target/linux/lantiq/image/Makefile b/target/linux/lantiq/image/Makefile index 031c3fcb83..c4419ce629 100644 --- a/target/linux/lantiq/image/Makefile +++ b/target/linux/lantiq/image/Makefile @@ -617,13 +617,29 @@ TARGET_DEVICES += lantiq_easy80920-nor define Device/avm_fritz3370 $(Device/AVM) $(Device/NAND) - BOARD_NAME := FRITZ3370 DEVICE_DTS := FRITZ3370 - DEVICE_TITLE := Fritz!Box WLan - FRITZ3370 - DEVICE_PACKAGES := kmod-ath9k wpad-mini kmod-usb-dwc2 - SUPPORTED_DEVICES += FRITZ3370 + DEVICE_TITLE := AVM Fritz!Box WLan 3370 Rev. 2 + KERNEL_SIZE := 4096k + UBINIZE_OPTS := -E 5 + IMAGES += eva-kernel.bin eva-filesystem.bin + IMAGE/eva-kernel.bin := append-kernel + IMAGE/eva-filesystem.bin := append-ubi + DEVICE_PACKAGES := kmod-ath9k wpad-mini kmod-usb-dwc2 fritz-tffs endef -TARGET_DEVICES += avm_fritz3370 + +define Device/avm_fritz3370-rev2-hynix + $(Device/avm_fritz3370) + DEVICE_DTS := FRITZ3370-REV2-HYNIX + DEVICE_TITLE := AVM Fritz!Box WLan 3370 Rev. 2 (Hynix NAND) +endef +TARGET_DEVICES += avm_fritz3370-rev2-hynix + +define Device/avm_fritz3370-rev2-micron + $(Device/avm_fritz3370) + DEVICE_DTS := FRITZ3370-REV2-MICRON + DEVICE_TITLE := AVM Fritz!Box WLan 3370 Rev. 2 (Micron NAND) +endef +TARGET_DEVICES += avm_fritz3370-rev2-micron define Device/avm_fritz7360sl $(Device/AVM) -- 2.25.1