From 07e555d8735e8fa272e3f6abd35acc9f1ab44367 Mon Sep 17 00:00:00 2001 From: David Bauer Date: Sun, 13 Oct 2019 23:37:59 +0200 Subject: [PATCH] mpc85xx: correct TP-LINK TL-WDR4900 MAC addresses This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment. Previously, the MAC addrss was read for the ethernet from the "config" partition. However, the content of this partition is dependent on the firmware which was previously installed on the device. Switch the MAC address source to the U-Boot partition, where the MAC address is always present at a fixed partition. The partition was previously already used for the WiFi MAC-addresses. Reviewed-by: Adrian Schmutzler Signed-off-by: David Bauer --- target/linux/mpc85xx/base-files/etc/board.d/02_network | 2 +- .../mpc85xx/files/arch/powerpc/boot/dts/tl-wdr4900-v1.dts | 6 +++--- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/target/linux/mpc85xx/base-files/etc/board.d/02_network b/target/linux/mpc85xx/base-files/etc/board.d/02_network index f907fd2edb..aa33a4af96 100755 --- a/target/linux/mpc85xx/base-files/etc/board.d/02_network +++ b/target/linux/mpc85xx/base-files/etc/board.d/02_network @@ -21,7 +21,7 @@ ocedo,panda) tplink,tl-wdr4900-v1) ucidef_add_switch "switch0" \ "0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan" - ucidef_set_interface_macaddr "wan" "$(mtd_get_mac_binary config 0x14c)" + ucidef_set_interface_macaddr "wan" "$(macaddr_add $(mtd_get_mac_binary u-boot 0x4fc00) 1)" ;; *) ucidef_set_interfaces_lan_wan "eth0" "eth1" diff --git a/target/linux/mpc85xx/files/arch/powerpc/boot/dts/tl-wdr4900-v1.dts b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/tl-wdr4900-v1.dts index 0e0d74c0d8..0998a4933a 100644 --- a/target/linux/mpc85xx/files/arch/powerpc/boot/dts/tl-wdr4900-v1.dts +++ b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/tl-wdr4900-v1.dts @@ -49,7 +49,7 @@ #address-cells = <1>; #size-cells = <1>; - partition@0 { + uboot: partition@0 { reg = <0x0 0x0050000>; label = "u-boot"; read-only; @@ -67,7 +67,7 @@ label = "firmware"; }; - config: partition@fe0000 { + partition@fe0000 { reg = <0x00fe0000 0x00010000>; label = "config"; read-only; @@ -119,7 +119,7 @@ enet0: ethernet@b0000 { phy-handle = <&phy0>; phy-connection-type = "rgmii-id"; - mtd-mac-address = <&config 0x144>; + mtd-mac-address = <&uboot 0x4fc00>; }; enet1: ethernet@b1000 { -- 2.25.1