From 06345f89b9a1e9acaf74cbbf896559b4286c102e Mon Sep 17 00:00:00 2001 From: Etienne Dechamps Date: Thu, 1 Jan 2015 16:59:45 +0000 Subject: [PATCH] Recalculate and resend MTU probes if they are too large for the system. Currently, if a MTU probe is sent and gets rejected by the system because it is too large (i.e. send() returns EMSGSIZE), the MTU discovery algorithm is not aware of it and still behaves as if the probe was actually sent. This patch makes the MTU discovery algorithm recalculate and send a new probe when this happens, so that the probe "slot" does not go to waste. --- src/net_packet.c | 62 +++++++++++++++++++++++++++--------------------- 1 file changed, 35 insertions(+), 27 deletions(-) diff --git a/src/net_packet.c b/src/net_packet.c index 84d4915..a7ddcdf 100644 --- a/src/net_packet.c +++ b/src/net_packet.c @@ -991,33 +991,41 @@ static void try_mtu(node_t *n) { if(n->mtuprobes == 0) n->maxmtu = choose_initial_maxmtu(n); - /* Decreasing the number of probes per cycle might make the algorithm react faster to lost packets, - but it will typically increase convergence time in the no-loss case. */ - const length_t probes_per_cycle = 8; - - /* This magic value was determined using math simulations. - It will result in a 1329-byte first probe, followed (if there was a reply) by a 1407-byte probe. - Since 1407 is just below the range of tinc MTUs over typical networks, - this fine-tuning allows tinc to cover a lot of ground very quickly. - This fine-tuning is only valid for maxmtu = MTU; if maxmtu is smaller, - then it's better to use a multiplier of 1. Indeed, this leads to an interesting scenario - if choose_initial_maxmtu() returns the actual MTU value - it will get confirmed with one single probe. */ - const float multiplier = (n->maxmtu == MTU) ? 0.97 : 1; - - const float cycle_position = probes_per_cycle - (n->mtuprobes % probes_per_cycle) - 1; - const length_t minmtu = MAX(n->minmtu, 512); - const float interval = n->maxmtu - minmtu; - - /* The core of the discovery algorithm is this exponential. - It produces very large probes early in the cycle, and then it very quickly decreases the probe size. - This reflects the fact that in the most difficult cases, we don't get any feedback for probes that - are too large, and therefore we need to concentrate on small offsets so that we can quickly converge - on the precise MTU as we are approaching it. - The last probe of the cycle is always 1 byte in size - this is to make sure we'll get at least one - reply per cycle so that we can make progress. */ - const length_t offset = powf(interval, multiplier * cycle_position / (probes_per_cycle - 1)); - - send_udp_probe_packet(n, minmtu + offset); + for (;;) { + /* Decreasing the number of probes per cycle might make the algorithm react faster to lost packets, + but it will typically increase convergence time in the no-loss case. */ + const length_t probes_per_cycle = 8; + + /* This magic value was determined using math simulations. + It will result in a 1329-byte first probe, followed (if there was a reply) by a 1407-byte probe. + Since 1407 is just below the range of tinc MTUs over typical networks, + this fine-tuning allows tinc to cover a lot of ground very quickly. + This fine-tuning is only valid for maxmtu = MTU; if maxmtu is smaller, + then it's better to use a multiplier of 1. Indeed, this leads to an interesting scenario + if choose_initial_maxmtu() returns the actual MTU value - it will get confirmed with one single probe. */ + const float multiplier = (n->maxmtu == MTU) ? 0.97 : 1; + + const float cycle_position = probes_per_cycle - (n->mtuprobes % probes_per_cycle) - 1; + const length_t minmtu = MAX(n->minmtu, 512); + const float interval = n->maxmtu - minmtu; + + /* The core of the discovery algorithm is this exponential. + It produces very large probes early in the cycle, and then it very quickly decreases the probe size. + This reflects the fact that in the most difficult cases, we don't get any feedback for probes that + are too large, and therefore we need to concentrate on small offsets so that we can quickly converge + on the precise MTU as we are approaching it. + The last probe of the cycle is always 1 byte in size - this is to make sure we'll get at least one + reply per cycle so that we can make progress. */ + const length_t offset = powf(interval, multiplier * cycle_position / (probes_per_cycle - 1)); + + length_t maxmtu = n->maxmtu; + send_udp_probe_packet(n, minmtu + offset); + /* If maxmtu changed, it means the probe was rejected by the system because it was too large. + In that case, we recalculate with the new maxmtu and try again. */ + if(n->mtuprobes < 0 || maxmtu == n->maxmtu) + break; + } + if(n->mtuprobes >= 0) n->mtuprobes++; } -- 2.25.1