Lokesh Vutla [Mon, 7 Oct 2019 13:56:35 +0000 (19:26 +0530)]
dt-bindings: memory-controller: Introduce J721E DDRSS bindings
Add DT binding documentation for DDR sub system present on J721E device.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
James Doublesin [Mon, 7 Oct 2019 08:34:27 +0000 (14:04 +0530)]
ram: k3-am654: Do not rely on default values for certain DDR register
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
James Doublesin [Mon, 7 Oct 2019 08:34:26 +0000 (14:04 +0530)]
ram: k3-am654: add support for LPDDR4 and DDR3L DDRs
Added training support for LPDDR4 and DDR3L DDRs. Also added/changed
some register configuration to support all 3 DDR types
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
James Doublesin [Mon, 7 Oct 2019 08:34:25 +0000 (14:04 +0530)]
armv7r: dts: am654-base-board: Rename 1600MHz to 1600MTs in dtsi filename
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 7 Oct 2019 08:22:17 +0000 (13:52 +0530)]
arm: K3: Clean and invalidate Linux Image before jumping to Linux
U-Boot cleans and invalidate L1 and L2 caches before jumping to Linux
by set/way in cleanup_before_linux(). Additionally there is a custom
hook provided to clean and invalidate L3 cache.
Unfortunately on K3 devices(having a coherent architecture), there is no
easy way to quickly clean all the cache lines for L3. The entire address
range needs to be cleaned and invalidated by Virtual Address. This can
be implemented using the L3 custom hook but it take lot of time to clean
the entire address range. In the interest of boot time this might not be
a viable solution.
The best hit is to make sure the loaded Linux image is flushed so that
the entire image is written to DDR from L3. When Linux starts running with
caches disabled the full image is available from DDR.
Reported-by: Andrew F. Davis <afd@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 7 Oct 2019 08:22:16 +0000 (13:52 +0530)]
cmd: booti: Store OS start and end info in images structure
Store the start and end of the OS image that is loaded in images
structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 7 Oct 2019 08:22:15 +0000 (13:52 +0530)]
boot: arm: Enable support for custom board_prep_linux
Once the arch specific boot_prepare_linux completes, boards wants to
have a custom preparation for linux. Add support for a custom
board_prep_linux.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Faiz Abbas [Wed, 9 Oct 2019 10:35:20 +0000 (12:35 +0200)]
configs: dra7xx_evm: Increase the size of SPL_MULTI_DTB_FIT
Expand SPL_MULTI_DTB_FIT to accommodate usb peripheral nodes being
added to support SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Faiz Abbas [Wed, 9 Oct 2019 10:35:19 +0000 (12:35 +0200)]
configs: dra7xx_evm: Add Kconfigs for SPL_DFU bootmode
Enable configs for supporting SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Faiz Abbas [Wed, 9 Oct 2019 10:35:18 +0000 (12:35 +0200)]
ARM: dts: dra7: Add usb peripheral nodes in spl
Add usb peripheral and usb phy nodes in spl to enable SPL_DFU bootmode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tom Rini [Thu, 24 Oct 2019 13:51:48 +0000 (09:51 -0400)]
Merge branch '2019-10-24-UFS-support'
- Add Universal Flash Storage (UFS) support
Tom Rini [Thu, 24 Oct 2019 11:32:21 +0000 (07:32 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Add support for HyperBus Memory Controller of TI's J721e
and AM654 SoCs (Vignesh)
Vignesh Raghavendra [Wed, 23 Oct 2019 08:00:05 +0000 (13:30 +0530)]
configs: j721e_evm_a72_defconfig: Add HBMC related configs
Enable HBMC and HyperFlash in A72 SPL and A72 U-Boot
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Vignesh Raghavendra [Wed, 23 Oct 2019 08:00:04 +0000 (13:30 +0530)]
configs: j721e_evm.h: Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT
Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT so that number of flash banks
are automatically detected by CFI flash driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Vignesh Raghavendra [Wed, 23 Oct 2019 08:00:03 +0000 (13:30 +0530)]
arm: dts: k3-j721e-som-p0: Add HyperFlash node
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Vignesh Raghavendra [Wed, 23 Oct 2019 08:00:02 +0000 (13:30 +0530)]
arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node
Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Vignesh Raghavendra [Wed, 23 Oct 2019 08:00:01 +0000 (13:30 +0530)]
mtd: Add TI HyperBus Memory Controller driver
AM654/J721e has HyperBus Memory Controller that supports HyperFlash and
HyperRAM devices. It provides a memory mapped interface to interact with
these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes
HyperFlash child node.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Vignesh Raghavendra [Wed, 23 Oct 2019 08:00:00 +0000 (13:30 +0530)]
mtd: cfi_flash: Use CONFIG_SYS_MONITOR_BASE only when defined
Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build
error when CONFIG_SYS_MONITOR_BASE is not defined.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Faiz Abbas [Tue, 15 Oct 2019 12:54:42 +0000 (18:24 +0530)]
configs: j721e_evm_a72: Enable configs for UFS
Enable SCSI and UFS related configs.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:41 +0000 (18:24 +0530)]
env: ti: Add environment variables to boot from UFS
Add environment variables to boot kernel from a filesystem contained in
the 2nd UFS LUN. The user can boot from a ufs filesystem just by
entering the following commands.
=> setenv boot ufs
=> boot
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:40 +0000 (18:24 +0530)]
cmd: Add Support for UFS commands
Add Support for commands to initialize and configure UFS devices.
TODO: Add Support for commands to resize and reconfigure LUNs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:39 +0000 (18:24 +0530)]
arm: dts: k3-j721e-main: Add UFS nodes
Add TI UFS glue layer and Cadence UFS Host controller DT nodes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:38 +0000 (18:24 +0530)]
ufs: Add glue layer driver for TI J721E devices
Add glue layer driver for the controller present on TI's J721E devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:37 +0000 (18:24 +0530)]
ufs: Add Support for Cadence platform UFS driver
Add Support for the platform driver for the Cadence device present on
TI's J721e device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:36 +0000 (18:24 +0530)]
ufs: Add Initial Support for UFS subsystem
Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:
- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
Also register this host controller as a SCSI host controller.
Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:35 +0000 (18:24 +0530)]
scsi: Add dma direction member to command structure
Some SCSI devices like UFS use DMA for executing scsi commands and hence
need to know the direction of transfer of the dma. Add a dma_dir element
to the command structure to facilitate this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:34 +0000 (18:24 +0530)]
scsi: Retry inquiry 3 times to overcome Unit Attention condition
The UFS SCSI device LUNs are observed to return failure the first time a
unit ready inquiry is sent and pass on the second try. Send this
inquiry 3 times to make sure device is ready.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:33 +0000 (18:24 +0530)]
scsi: Add max_bytes_per_req to scsi_platdata
Add max_bytes_per_req to scsi_platdata to enable the host driver to limit
the number of bytes that can be read/written per request.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 15 Oct 2019 12:54:32 +0000 (18:24 +0530)]
scsi: Simplify scsi_read()/_write()
With no non-DM driver using scsi_read()/_write() APIs, remove
the legacy implementations.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[trini: Reorder slightly and mark scsi_read/write behind BLK test to
avoid warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 23 Oct 2019 18:04:02 +0000 (14:04 -0400)]
Merge tag 'u-boot-stm32-2019-10-23' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Disable CONFIG_NET flag for MCU STM32
- Fix ramdisk_addr_r for stm32f746-disco
- Fix USB product id for stm32mp1
Tom Rini [Wed, 23 Oct 2019 11:55:20 +0000 (07:55 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- Add LS1027A, LS1018A, LS1017A support
- Few updates related to usb, ls1012a, lx2160a
Patrick Delaunay [Fri, 13 Sep 2019 13:24:17 +0000 (15:24 +0200)]
board: stm32mp1: fixup the usb product id for USB download gadget
Select the correct USB product id used by the download gadget
for ST stm32mp1 boards.
The board stm32mp1 select the correct product id, as defined in
http://www.linux-usb.org/usb.ids for the STMicroelectronics
vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM):
- dfu = 0xdf11 : STM Device in DFU mode
it is the value used by ROM code and reused for stm32prog
command
- fasboot = 0x0afb : Android Fastboot device
- others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM)
Mass Storage Device
it is used for UMS command / usb_dnl_ums
This patch avoid conflict when the same USB VID/PID is used for
ums, fastboot or dfu command (two different protocols associated
to the same PID).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Mon, 16 Sep 2019 08:56:51 +0000 (10:56 +0200)]
configs: stm32f746-disco: Fix ramdisk_addr_r
Set ramdisk_addr_r to 0xC0600000.
Reported-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:45 +0000 (10:09 +0200)]
configs: stm32h743-eval: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:44 +0000 (10:09 +0200)]
configs: stm32h743-disco: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:43 +0000 (10:09 +0200)]
configs: stm32f469-discovery: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:42 +0000 (10:09 +0200)]
configs: stm32f429-evaluation: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrice Chotard [Tue, 17 Sep 2019 08:09:41 +0000 (10:09 +0200)]
configs: stm32f429-discovery: Disable CONFIG_NET flag
Network support was never added on this board, disable
CONFIG_NET flag to avoid following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Mon, 21 Oct 2019 13:02:40 +0000 (15:02 +0200)]
dm: pinctrl: fix for introduce PINCONF_RECURSIVE option
Correct the name of the define used CONFIG_IS_ENABLED which is
not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE.
The recursive calls is conditional only for UCLASS_PINCONFIG
"pinconfig" driver.
It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL
"pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to
be removed for this driver.
This correct a regression introduced because the same patch is
applied twice times in u-boot-dm branch:
- commit
e878b53a79d1 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit
c20851b3d850 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Mon, 21 Oct 2019 13:07:54 +0000 (15:07 +0200)]
pinctrl: Kconfig: remove duplicated nodes
Remove the duplicated configs introduced when the same patch is
applied twice times:
- commit
e878b53a79d1 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
- commit
c20851b3d850 ("dm: pinctrl: introduce PINCONF_RECURSIVE
option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Biwen Li [Mon, 21 Oct 2019 06:53:30 +0000 (12:23 +0530)]
armv7: ls102xa: Don't power down OCRAM1 during deep sleep
To allow OCRAM to be used as wakeup source in
deep sleep, do not power it down.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Wed, 25 Sep 2019 10:40:42 +0000 (18:40 +0800)]
armv7: ls102xa: add errata ID A-008646 for workaround
The patch adds an errata ID A-008646 for workaround
to provide more information by errata ID.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Wasim Khan [Tue, 15 Oct 2019 08:54:11 +0000 (08:54 +0000)]
armv8: Update LX2160A/LX2120A/LX2080A SVR value
LX2160A/LX2120A/LX2080A SVR value should be
0x873600/0x873620/0x873602
Previous values were valid only if CAN fuse is blown.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Yuantian Tang [Thu, 10 Oct 2019 09:19:37 +0000 (17:19 +0800)]
armv8: ls1028a: disable multimedia for ls1027a, ls1017a
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a.
Both ls1027a and ls1017a personalities are lower functionality version
which doesn't support the multimedia subsystems, like LCD, GPU.
To disable multimedia feature on non-multimedia version,
set the status property to disabled in dts nodes.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Udit Agarwal [Mon, 30 Sep 2019 10:16:57 +0000 (10:16 +0000)]
board/ls1028a: Add call to sec_init()
Adds sec_init call to initialise the job ring parameters
for secure boot operations.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Mon, 30 Sep 2019 07:08:34 +0000 (12:38 +0530)]
configs: ls1012afrwy: Add CONFIG_ENV_ADDR
This configuration enables picking the environment from flash before
DDR init.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Wed, 25 Sep 2019 09:48:11 +0000 (17:48 +0800)]
armv7: ls102xa: Correct endianness of SCFG_SPARECR8 read
The patch corrects endianness of register SCFG_SPARECR8 read
in_le32 -> in_be32
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Ran Wang [Fri, 20 Sep 2019 09:34:29 +0000 (17:34 +0800)]
armv8: fsl-layerscape: Make USB masters snoopable
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and
SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write
snoop signal on LS1043A and LS1046A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Wed, 18 Sep 2019 10:58:04 +0000 (16:28 +0530)]
armv7: ls102xa: Update SCFG_QSPI_CLKSEL value
Update SCFG_QSPI_CLKSEL value : 0xC -> 0x5
which means ClusterPLL/16
Signed-off-by: Ashish Kumar <Ashish.kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Wed, 18 Sep 2019 09:28:11 +0000 (14:58 +0530)]
configs: ls1012ardb: Add CONFIG_ENV_ADDR
CONFIG_ENV_ADDR config option enables picking the environment from
flash before DDR init.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Yuantian Tang [Wed, 18 Sep 2019 08:50:52 +0000 (16:50 +0800)]
armv8: ls1028a: Add more personalities support
Add LS1027A, LS1018A and LS1017A personalities support to
LS1028A SoC family.
LS1028A is the prime personality of LS1028A SoC family.
LS1027A is a lower funtionality version of QorIQ LS1028A
which does not support the multimedia subsystems, such as LCD
controller, GPU, and eDP PHY.
The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72
core, low power versions of the QorIQ LS1028A and LS1027A
SoCs respectively.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Anatolij Gustschin [Fri, 18 Oct 2019 19:38:33 +0000 (21:38 +0200)]
spl: mmc: make eMMC HW boot partition configuration optional
Loading U-Boot on i.MX8QXP MEK board is broken since recent changes
in spl_mmc:
U-Boot SPL
2019.10-00162-gff5bd397e4 (Oct 18 2019 - 15:50:45 +0200)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
Load image from MMC/SD 0x46400
spl: mmc partition switch failed
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The newly added CONFIG_SYS_MMCSD_RAW_MODE_EMMC_BOOT_PARTITION option
is selected automatically and overrides the EXT_CSC_PART_CONFIG
configurations with default value, always selecting the eMMC boot
partition 1. Boards which place U-Boot image in other partitions
became not bootable.
Fix this by making the eMMC HW boot partition selection optional.
Fixes:
17241ea0543a (spl: mmc: Add option to set eMMC HW boot partition)
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tom Rini [Fri, 18 Oct 2019 20:37:03 +0000 (16:37 -0400)]
Merge tag 'efi-2020-01-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1 (2)
Install the simple file protocol only if there is a file system on the
partition.
Enable CONFIG_CMD_NVEDIT_EFI on QEMU.
Tom Rini [Fri, 18 Oct 2019 20:36:44 +0000 (16:36 -0400)]
Merge tag 'u-boot-amlogic-
20191018' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools
- add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board
- add support for Amlogic A311D based Khadas VIM3
- add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
Tom Rini [Fri, 18 Oct 2019 20:36:16 +0000 (16:36 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- Support sifive DM based gpio driver for FU540-SoC.
- Align boot image header with Linux v5.3
Guillaume La Roque [Fri, 11 Oct 2019 15:33:58 +0000 (17:33 +0200)]
configs: sei610: Add config file to fix userdata size
Add separate config file to handle the different eMMC size on
the sei610 board.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Guillaume La Roque [Fri, 11 Oct 2019 15:33:57 +0000 (17:33 +0200)]
configs: sei510: rework header and fix userdata size
Move android generic config and boot sequence in meson64_android header
and fix size of userdata to use all eMMC on SEI510.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:56 +0000 (17:33 +0200)]
boards: amlogic: add SEI610 support
Add support for the customer board SEI610 manufactured by SEI Robotics
with the following specifications:
- Amlogic S905X3 ARM Cortex-A55 quad-core SoC
- 2GB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- 1 x USB Type-C DRD
- 1 x FTDI USB Serial Debug Interface
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
Like it's SEI510 counterpart, the boot flow is designed to boot
Android AOSP built for the Yukawa Android device.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:55 +0000 (17:33 +0200)]
ARM: dts: meson-sm1: add U-Boot specific DT for graphics
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to
match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi
to handle the U-Boot specific DT for graphics.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 13:12:20 +0000 (15:12 +0200)]
configs: sei510: enable everything-else power domain
The GX VPU Power Domain driver has been replaced by the Everything-Else
Power Domain driver for G12A and SM1.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 13:12:19 +0000 (15:12 +0200)]
power: domain: add Amlogic Everything-Else power domain driver
Based on the
54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain
driver for Amlogic SoCs.
This driver handles the VPU Power domain and other domains from the
Everything-Else part of the SM1 and G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:54 +0000 (17:33 +0200)]
ARM: dts: Import SEI610 DT from Linux 5.4-rc2
Import the Amlogic SM1 DT and the SEI610 board DT from [1]
[1]
da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:53 +0000 (17:33 +0200)]
clk: meson-sm1: add compatible
The SM1 clock controller is almost identical to the G12A and
so far the differences don't matter.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:52 +0000 (17:33 +0200)]
mmc: meson-gx: add support for mmc-pwrseq-emmc
Add support for mmc-pwrseq-emmc in the meson-gx mmc driver to support
enabling the eMMC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 11 Oct 2019 15:33:51 +0000 (17:33 +0200)]
ARM: meson: add SM1 SoC id
Add the missing IDs to detect the SM1 S905X3 SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:57 +0000 (16:03 +0200)]
arm: meson: Recognize A311D SoC
Values imported from Linux driver, but in correct numeric order.
Khadas VIM3 prints: Amlogic Meson G12B (A311D) Revision 29:b (10:2)
Cc: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:56 +0000 (16:03 +0200)]
arm: meson: Tidy SoC information output
Write SoC instead of Soc. The Linux driver is not affected.
Fixes:
f41d723b9f ("ARM: meson: display Amlogic SoC Information")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:55 +0000 (16:03 +0200)]
configs: Add Khadas VIM3 defconfig
Derived from odroid-n2_defconfig and README.odroid-n2.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Andreas Färber [Wed, 9 Oct 2019 14:03:54 +0000 (16:03 +0200)]
arm: dts: Import and update DT for Khadas VIM3
In Linux meson-g12-common.dtsi was introduced as well as new g12b nodes
and headers, as dependencies of new meson-g12b-a311d-khadas-vim3.dts.
Copied from
da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Fri, 30 Aug 2019 12:09:28 +0000 (14:09 +0200)]
configs: sei510: enable Video Display support
Add the necessary config options to support BMP display over HDMI,
and add a preboot command to load the BMP file from a predefined
eMMC partition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:27 +0000 (14:09 +0200)]
ARM: dts: meson-g12a: add U-Boot specific DT for graphics
Like the meson-gx support, add the U-Boot specific bits in DT
to support graphics on G12A SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:26 +0000 (14:09 +0200)]
arm: meson: board-g12a: Setup VPU in fdt
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.
Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:25 +0000 (14:09 +0200)]
video: meson: add compatible for Amlogic G12A
Finally add the Amlogic G12A SoC compatible for the VPU driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:24 +0000 (14:09 +0200)]
video: meson: sync with linux drm-misc tree
Synchronize the Amlogic Meson Video driver back with the latest
DRM misc tree, adding G12A platform support, from the latest commit:
528a25d040bc ("drm: meson: use match data to detect vpu compatibility")
The sync includes the following changes from Linux adapted to U-Boot:
- Add support for VIC alternate timings
- Switch PLL to 5.94GHz base for 297Mhz pixel clock
- Add registers for G12A SoC
- Add G12A Support for VPP setup
- Add G12A Support for VIU setup
- Add G12A support for OSD1 Plane
- Add G12A support for plane handling in CRTC driver
- Add G12A support for CVBS Encoder
- Add G12A Video Clock setup
- Add G12A support for the DW-HDMI Glue
- fix G12A HDMI PLL settings for 4K60 1000/1001 variations
- fix primary plane disabling
- fix G12A primary plane disabling
- mask value when writing bits relaxed
- crtc: drv: vpp: viu: venc: use proper macros instead of magic constants
- global clean-up
- add macro used to enable HDMI PLL
- venc: set the correct macrovision max amplitude value
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:23 +0000 (14:09 +0200)]
video: meson: remove power domain get
Remove getting and enabling the node power domain since it's now handled
by the dm core directly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:22 +0000 (14:09 +0200)]
clk: meson: g12a: add support for VPU/HDMI clocks
Add necessary clock support to set up clock for the VPU and
HDMI support.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Neil Armstrong [Fri, 30 Aug 2019 12:09:21 +0000 (14:09 +0200)]
power: domain: meson-gx-pwrc: add G12A support
Add Amlogic G12A support for the gx-pwrc driver, aligned on the
Linux v5.2 driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Daniel Drake [Tue, 6 Aug 2019 08:10:42 +0000 (16:10 +0800)]
board: amlogic: document alternative libretech-cc installation methods
As already documented in this README, several binaries must be
glued together in order to boot the device.
Extend the documentation to cover the prebuilt binaries
(saving you the hassle of installing ancient cross-compilers),
and also mention the open source replacements for the encryption
tool (which is especially useful if you want to avoid requiring
32-bit x86 binaries in your build system).
Signed-off-by: Daniel Drake <drake@endlessm.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Atish Patra [Wed, 9 Oct 2019 17:34:17 +0000 (10:34 -0700)]
RISC-V: Align boot image header with Linux
The released Linux boot image header in v5.3 is different from the
one present in U-Boot. Align the header with the new version. The
changes in Linux are backward compatible. Previous U-Boot releases
with older header will continue to work as well. As v5.3 kernel is
the first one to support image header, there is no compatibility
issue between new U-Boot (with this patch) and older kernel.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Sagar Shrikant Kadam [Tue, 1 Oct 2019 17:00:47 +0000 (10:00 -0700)]
configs: fu540: enable gpio driver
Enable the DM based GPIO driver for FU540-C000 SoC.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Sagar Shrikant Kadam [Tue, 1 Oct 2019 17:00:46 +0000 (10:00 -0700)]
gpio: sifive: add support for DM based gpio driver for FU540-SoC
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.
This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]
[1]: https://lkml.org/lkml/2018/10/9/1103
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Sun, 13 Oct 2019 09:54:20 +0000 (11:54 +0200)]
efi_loader: enable CONFIG_CMD_NVEDIT_EFI on QEMU
To reduce the default image size CONFIG_CMD_NVEDIT_EFI was disabled by
default. Re-enable it on the QEMU platforms supporting the UEFI sub-system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:38 +0000 (14:59 +0900)]
efi_loader: disk: install FILE_SYSTEM_PROTOCOL only if available
In the current implementation, EFI_SIMPLEFILE_SYSTEM_PROTOCOL is always
installed to all the partitions even if some of them may house no file
system.
With this patch, that protocol will be installed only if any file system
exists.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:37 +0000 (14:59 +0900)]
fs: add fs_get_type() for current filesystem type
This function is a variant of fs_get_type_name() and returns a filesystem
type with which the current device is associated.
We don't want to export fs_type variable directly because we have to take
care of it consistently within fs.c.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:36 +0000 (14:59 +0900)]
fs: clean up around fs_type
fs_ls(), fs_mkdir() and fs_unlink() sets fs_type to FS_TYPE_ANY
explicitly, but it is redundant as they call fs_close().
So just remove those lines.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sun, 13 Oct 2019 08:26:26 +0000 (10:26 +0200)]
fs: update fs_close() description
Provide a more detailed description of fs_close().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Mon, 7 Oct 2019 05:59:35 +0000 (14:59 +0900)]
fs: export fs_close()
fs_close() closes the connection to a file system which opened with
either fs_set_blk_dev() or fs_set_dev_with_part(). Many file system
functions implicitly call fs_close(), e.g. fs_closedir(), fs_exist(),
fs_ln(), fs_ls(), fs_mkdir(), fs_read(), fs_size(), fs_write()
and fs_unlink().
So just export it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Wed, 9 Oct 2019 07:19:52 +0000 (16:19 +0900)]
efi_loader: device_path: check against file path length
device_path strcuture has 2 bytes of "length" field, and so
file path length should not exceed this limit, 65535.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Thu, 17 Oct 2019 11:26:16 +0000 (07:26 -0400)]
Merge tag 'for-v2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-ubi
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
Tom Rini [Wed, 16 Oct 2019 22:10:31 +0000 (18:10 -0400)]
Merge tag 'dm-pull-15oct19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
Tom Rini [Wed, 16 Oct 2019 22:10:01 +0000 (18:10 -0400)]
Merge branch '2019-10-15-master-imports'
- Split travis jobs again so we don't have failures due to excessive
build times.
- Android image updates
- cscope bugfix, update ARM maintainers entry, drop H2200 platform.
Tom Rini [Mon, 14 Oct 2019 22:12:59 +0000 (18:12 -0400)]
travis: Split and rename xilinx ARM in to two jobs
Split the ARMv7 and AArch64 platforms into separate jobs, to avoid them
taking too long to build overall. Also rename them from "Xilinx" to
"Zynq*" to reflect slightly better what is being built and to pull in a
few more board matches.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 15 Oct 2019 11:27:14 +0000 (07:27 -0400)]
travis: Split sun8i in to two jobs
Split the 32bit and 64bit platforms into separate jobs, to avoid them
taking too long to build overall.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 15 Oct 2019 11:27:13 +0000 (07:27 -0400)]
travis: Split i.MX jobs a bit more
- Split "tqc" and "technexion" out into their own jobs and exclude
them from the catch-all jobs
- Clarify the job labels a little more.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tom Rini [Thu, 10 Oct 2019 21:33:09 +0000 (17:33 -0400)]
MAINTAINERS: Update ARM entry
Fully take over the ARM maintainers entry.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Andy Shevchenko [Tue, 8 Oct 2019 18:12:45 +0000 (21:12 +0300)]
Makefile: Skip symbolic links to files for cscope
cscope complains that it can't find files that appears to be symbolic links
cscope: cannot find file tools/binman/test/u_boot_binman_syms_bad.c
cscope: cannot find file tools/version.h
`find -L` tests properties, but name, and cscope can't cope with symbolic
links (a lot of bugs in upstream were simple closed as kinda invalid).
To work around the problem, exclude symbolic links from the cscope.files.
Note, it's done in two pass to speed up the process (`-exec realpath ...`
approach is not portable and introduces a 3x delay).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Heinrich Schuchardt [Tue, 8 Oct 2019 18:54:49 +0000 (20:54 +0200)]
arm: remove the H2200 board
U-Boot cannot be built for h2200_defconfig with CONFIG_DM=y.
The maintainer Lukasz Dalek suggested to remove the board.
https://lists.denx.de/pipermail/u-boot/2019-August/380685.html
Cc: Lukasz Dalek <luk0104@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[trini: As this is the last non-toradex PXA board, update travis too]
Signed-off-by: Tom Rini <trini@konsulko.com>
Philippe Reynes [Mon, 14 Oct 2019 17:41:06 +0000 (19:41 +0200)]
ubi: env: fix redundand management
We check (with a #if defined()) the config ENV_UBI_VOLUME_REDUND
to know if there is a redundant env. But this config is a string
and is always defined with env is in ubi, so we always consider
that a redundand env is used.
To fix this issue, I've added a hidden flag ENV_UBI_IS_VOLUME_REDUND
that is true when ENV_UBI_VOLUME_REDUND is not "". Then, I check
this flag in the code, instead of the string ENV_UBI_VOLUME_REDUND.
hs: fixed typo s/condider/consider
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Tue, 17 Sep 2019 07:17:53 +0000 (09:17 +0200)]
ubi: Add "skipcheck" command to set/clear this bit in the UBI volume hdr
U-Boot now supports the "skip_check" flag to optionally skip the CRC
check at open time. Currently its only possible to set this bit upon
UBI volume creation. But it might be very useful to also set this bit
on already installed systems (e.g. field upgrade) to make also use of
the boot-time decrease on those systems.
This patch now adds a new "ubi" command "ubi skipcheck" to set or clear
this bit in the UBI volume header:
=> ubi skipcheck rootfs0 on
Setting skip_check on volume rootfs0
BTW: This saves approx. 10 seconds Linux bootup time on a MT7688 based
target with 128MiB of SPI NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Stefan Roese [Thu, 12 Sep 2019 14:41:02 +0000 (16:41 +0200)]
ubi: Print skip_check in ubi_dump_vol_info()
It might be interesting, if "skip_check" is set or not, so lets print
this flag in ubi_dump_vol_info() as well.
hs: fix typo in commit message
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
projects / oweals / u-boot.git / log