Łukasz Majewski [Fri, 16 Aug 2013 13:31:45 +0000 (15:31 +0200)]
i2c:multibus:fix: Correct I2C_MULTI_BUS value when support for many buses is enabled
The I2C_MULTI_BUS needs to be defined for correct I2C operation with
many software emulated I2C controllers.
This fix restores correct value of the I2C_MULTI_BUS changed by following
commit:
SHA1:
385c9ef5a7215b2b0c22836fee6c692dfc8559d7
i2c: add i2c_core and prepare for new multibus support
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Chunhe Lan [Fri, 16 Aug 2013 07:10:37 +0000 (15:10 +0800)]
fsl_i2c: add workaround for the erratum I2C
A004447
This workaround is for the erratum I2C
A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.
At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.
The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Chunhe Lan [Fri, 16 Aug 2013 07:10:36 +0000 (15:10 +0800)]
fsl_i2c: generate nine pulses on SCL if the I2C bus is hung
When the code detected that the bus is hung (e.g. SDA stuck low),
send 9 pulses on SCL to try to fixup the bus.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Tom Rini [Mon, 19 Aug 2013 21:26:15 +0000 (17:26 -0400)]
Prepare v2013.10-rc1
Signed-off-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:47 +0000 (22:12 +0200)]
SPDX-License-Identifier: convert BSD-3-Clause files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini Don't remove some copyrights by accident]
Signed-off-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:46 +0000 (22:12 +0200)]
board/esd/cpci750/mv_eth.c: Fix license
The file header indicated that this file was GPL-2.0+, but actually
the code was derived from (Marvell based) Linux source code which is
only GPL-2.0. Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:45 +0000 (22:12 +0200)]
SPDX-License-Identifier: convert PIBS licensed files
This commit adapts the files that were derived from PIBS (PowerPC
Initialization and Boot Software) codeto using SPDX License
Identifiers.
So far, SPDX has not assigned an official License ID for the PIBS
license yet, so this should be considered preliminary.
Note that the following files contained incorrect license information:
arch/powerpc/cpu/ppc4xx/4xx_uart.c
arch/powerpc/cpu/ppc4xx/start.S
arch/powerpc/include/asm/ppc440.h
These files included, in addition to the GPL-2.0 / ibm-pibs dual
license as inherited from PIBS, a GPL-2.0+ license header which was
obviously incorrect. This has been removed.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
Licenses/README
Acked-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:44 +0000 (22:12 +0200)]
SPDX-License-Identifier: fixing some problematic GPL-2.0 files
Unlike the other patches in this series so far, this commit fixes a
ambiguity in the license terms for some OMAP files: the code was
originally derived from the Linux kernel sources, where it was clearly
marked as GPL-2.0 (i. e. without the "or later" part), but the U-Boot
version had a GPL-2.0+ file header added, apparently without
permission / relicensing from the original authors of the code.
Insert a GPL-2.0 SPDX-License-Identifier to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Sun, 28 Jul 2013 20:12:43 +0000 (22:12 +0200)]
SPDX-License-Identifier: convert GPL-2.0+ / BSD-2-Clause dual-licensed files
Signed-off-by: Wolfgang Denk <wd@denx.de>
Kuo-Jung Su [Wed, 10 Jul 2013 01:25:49 +0000 (09:25 +0800)]
net: ftmac110: Update tx/rx descriptor format
1. Reformat tx/rx descriptor as an uniform struct.
2. Replace uint32_t[2] with uint64_t for descriptor control.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Kuo-Jung Su [Wed, 10 Jul 2013 01:25:48 +0000 (09:25 +0800)]
net: ftmac110: struct ftmac110_regs __iomem * -> struct ftmac110_regs *
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Kuo-Jung Su [Wed, 10 Jul 2013 01:25:47 +0000 (09:25 +0800)]
net: ftmac110: Update license statement
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Jeroen Hofstee [Sat, 10 Aug 2013 14:52:47 +0000 (16:52 +0200)]
net.h: don't use the reserved name __unused
The __* keywords are reserved. On FreeBSD __unused evaluates
to the attribute unused, causing a compilation failure.
Just use unused instead.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: joe.hershberger@gmail.com
Tom Rini [Fri, 9 Aug 2013 19:58:18 +0000 (15:58 -0400)]
linkstation_HGLAN: Convert from unused CONFIG_BOOTP_MASK to specific list
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 18:43:05 +0000 (14:43 -0400)]
galaxy5200: Convert from unused CONFIG_BOOTP_MASK to specific list
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 18:39:51 +0000 (14:39 -0400)]
configs: Remove unused CONFIG_BOOTP_DEFAULT
Signed-off-by: Tom Rini <trini@ti.com>
Bhupesh Sharma [Thu, 18 Jul 2013 08:28:20 +0000 (13:58 +0530)]
net: phy/realtek: Add support for RTL8211DN and RTL8211E phy modules
This patch adds support for Realtek PHY modules RTL8211DN and
RTL8211E (variants: RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211EG-VB-CG),
which can be found on Freescale's T1040RDB boards.
To make the driver more generic across 8211 family, a generic name 8211x
is added for macros and function names.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Stefan Roese [Wed, 3 Jul 2013 16:34:54 +0000 (18:34 +0200)]
net: smsc95xx: Add support for another SMSC95xx variant
This patch adds support for the SMSC9500 with product id 0x9900 which is
equipped in the "EXSYS USB 2.0" etherner USB adapter.
Tested on omap3_beagle.
Signed-off-by: Stefan Roese <sr@denx.de>
Axel Lin [Wed, 3 Jul 2013 03:24:18 +0000 (11:24 +0800)]
net: Use ARRAY_SIZE at appropriate places
Use ARRAY_SIZE instead of having similar implementation in each drivers.
The NUMELEMS defined in drivers/net/npe/include/IxOsalTypes.h is not used
at all, so this patch removes it instead of converting it to use ARRAY_SIZE.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Fabio Estevam [Fri, 7 Jun 2013 00:04:19 +0000 (21:04 -0300)]
phy: smsc: LAN8710/8720 are not Gbit PHYs
LAN8710/8720 are 10/100 Mbps PHYs, so fix the '.features' field.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Axel Lin [Sat, 17 Aug 2013 07:39:34 +0000 (15:39 +0800)]
serial: arm_dcc: Convert to use default_serial_puts
Use default_serial_puts() instead of its own implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Dirk Eibach [Fri, 9 Aug 2013 08:52:54 +0000 (10:52 +0200)]
powerpc/ppc4xx: Fix dlvision-10g reset gpio
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Fri, 9 Aug 2013 08:52:53 +0000 (10:52 +0200)]
powerpc/ppc4xx: Do full iocon PHY initialization in software
Up to this point some PHY initialization was done from the FPGA
and some from u-boot.
From now all initialization is done from u-boot.
To keep this maintainable a PHY setup machine was implemented that can
execute commands from initialization arrays.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Fri, 9 Aug 2013 08:52:52 +0000 (10:52 +0200)]
powerpc/ppc4xx: Add support for iocon-2
Add a new iocon flavor with a second communiction port per channel.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Dirk Eibach [Fri, 9 Aug 2013 08:52:51 +0000 (10:52 +0200)]
powerpc/ppc4xx: Add support for iocon fiber
Add a new iocon flavor with fiber instead of copper connectivity.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Sun, 18 Aug 2013 18:14:34 +0000 (14:14 -0400)]
Merge branch 'master' of git://88.191.163.10/u-boot-arm
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
Albert ARIBAUD [Sat, 17 Aug 2013 16:24:13 +0000 (18:24 +0200)]
Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Axel Lin [Sat, 22 Jun 2013 10:22:48 +0000 (18:22 +0800)]
gpio: pca953x: Use ARRAY_SIZE instead of reinventing it
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
York Sun [Tue, 30 Jul 2013 22:26:11 +0000 (15:26 -0700)]
tools/Makefile: Move _GNU_SOURCE to Makefile
Commit
669dfc2e adds libfdt_env.h to HOSTCPPFLAGS. It causes stdio.h
to be included before _GNU_SOURCE is defined in C files. On some old hosts
some prototypes are protected by #ifdef __USE_GNU, which is set when
_GNU_SOURCE is defined.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 Jul 2013 03:10:01 +0000 (20:10 -0700)]
image: Display FIT timestamp when booting
The timestamp is shown in fit_print_contents() but for some reason not
in fit_image_print(). This seems to be an oversight, since it is the latter
which is used by bootm.
Add timestamp printing in this case.
(There is code duplication in these two function, for looking at in a future
patch).
Signed-off-by: Simon Glass <sjg@chromium.org>
Paul B. Henson [Sun, 4 Aug 2013 04:29:09 +0000 (21:29 -0700)]
bootm: fix conditional controlling call to fixup_silent_linux
This function is only defined if CONFIG_SILENT_CONSOLE is set and
CONFIG_SILENT_U_BOOT_ONLY is not set, the call to it should be based
on the same conditions.
Signed-off-by: Paul B. Henson <henson@acm.org>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 17 Jul 2013 03:10:00 +0000 (20:10 -0700)]
RFC: bootm: Add silent_linux environment variable
At present the console for linux is silent if the U-Boot console is silent,
unless CONFIG_SILENT_U_BOOT_ONLY is set. I wonder if a better way would be
to have an environment variable to control this? Then we can control the
verbosity from scripts, and set the variable to 'no' for those boards that
want Linux to boot with console output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Taras Kondratiuk [Tue, 16 Jul 2013 11:45:01 +0000 (14:45 +0300)]
SPL: Limit image name print length
If image name is longer than 32 bytes, then it will be truncated.
This will remove '\0' at the end of the line, so printf will
go out of string limit.
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Angus Ainslie [Wed, 26 Jun 2013 22:54:24 +0000 (16:54 -0600)]
Enable xmodem support
This is a trivial patch that just enables xmodem downloads using the existing
ymodem framework.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
TENART Antoine [Tue, 2 Jul 2013 10:06:00 +0000 (12:06 +0200)]
Add TI816X evm board support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Change to SPDX, fix a few compiler warnings, adapt to
CONFIG_OMAP_COMMON]
Signed-off-by: Tom Rini <trini@ti.com>
TENART Antoine [Tue, 2 Jul 2013 10:05:59 +0000 (12:05 +0200)]
Add TI816X support
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
TENART Antoine [Tue, 2 Jul 2013 10:05:58 +0000 (12:05 +0200)]
Prepare for TI816X : reuse existing code from TI814X
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
Heiko Schocher [Mon, 5 Aug 2013 14:00:38 +0000 (16:00 +0200)]
arm, da850: add ipam390 board support
add the am1808 based ipam390 board from Barix.
- 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM
interface
- 128MByte, NAND Flash, 8bit databus to the NANDFlash
Interface
- Ethernet PHY Micrel KSZ8051R via RMII
- Console on UART 0
- booting fron nand flash
- spl falcon bootmode
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Heiko Schocher [Mon, 5 Aug 2013 14:00:37 +0000 (16:00 +0200)]
arm, da850: enable the correct uart in arch_cpu_init()
in arch_cpu_init() uart2 is fix enabled, without reference the
setting from CONFIG_SYS_NS16550_COM1. Use the setting from
CONFIG_SYS_NS16550_COM1 for enabling the console.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Heiko Schocher [Mon, 5 Aug 2013 14:00:36 +0000 (16:00 +0200)]
bootstage: get more BOOTSTAGE_ID* in show_boot_progress()
In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name()
show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress()
if CONFIG_BOOTSTAGE is not defined.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
Heiko Schocher [Mon, 5 Aug 2013 14:00:35 +0000 (16:00 +0200)]
arm/davinci/da850: add uart0_pins_rtscts and RMII_MHz_50_CLK in emac_pins_rmii pinmux
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:20 +0000 (11:22 -0400)]
TI:armv7: Enable CONFIG_CMD_GPIO
Add the generic "poke a GPIO" command, with the GPIO related defines.
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:19 +0000 (11:22 -0400)]
TI:armv7: Enable CONFIG_CMD_SPI
Add the generic "poke the SPI bus" command, with the SPI related
defines.
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:18 +0000 (11:22 -0400)]
TI:omap5/dra7xx: Convert to ti_armv7_common.h
Update omap5_common.h to use ti_armv7_common.h, and in turn update
dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are
that IP blocks which exist on the platform, and had clocks enabled,
now have the drivers being built as well.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:17 +0000 (11:22 -0400)]
TI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xx
We create two new files, include/configs/ti_armv7_common.h for all of
the common IP blocks and related features / commands we share in
virtually all of our platforms. We then create
include/configs/ti_am335x_common.h for everything common to the am335x
SoC leaving just the board specific parts to
include/configs/ti_am335x_common.h.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:16 +0000 (11:22 -0400)]
am335x_evm: Bring in 'boot_fdt' logic from i.MX
Bring in the 'boot_fdt' environment variable that i.MX boards use to try
and load a device tree when booting.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:15 +0000 (11:22 -0400)]
arm: spl: For Falcon Mode, set a default machid of ~0
With device trees, boards do not always set CONFIG_MACH_TYPE now, so we
must not rely on this define being set. The kernel uses ~0 to see if we
have a valid machine number or not, so set that as the default, invalid
machine, id and only fix if CONFIG_MACH_TYPE is set.
Acked-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:14 +0000 (11:22 -0400)]
am335x_evm: Use default baud rate table
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:13 +0000 (11:22 -0400)]
am33xx: Stop using PHYS_DRAM_1 define
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1
in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 9 Aug 2013 15:22:12 +0000 (11:22 -0400)]
am33xx: CONFIG_DMA_COHERENT defines are unused, remove
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Javier Martinez Canillas [Wed, 7 Aug 2013 15:53:19 +0000 (17:53 +0200)]
OMAP3: igep00x0: allow booting with a FDT from MMC
IGEP boards now have Device Tree support in the mainline
kernel. To boot an IGEP board using a DT, a uEnv.txt plain
text file could be used to define a custom uenvcmd that will
be run by the default boot command.
It is more convenient to change the default boot command to
allow loading a FDT if it is stored in the boot dir of the
rootfs uSD/MMC partition.
If no FDT is found then the defaul command tries to boot a
zImage without a DT using legacy boot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Enric Balletbo i Serra [Wed, 7 Aug 2013 15:53:18 +0000 (17:53 +0200)]
ARM: igep00x0.h: Enable the use of CMD_EXT4, CMD_FS_GENERIC and zImage.
Able to load the kernel from some form of ext[234] or FAT. Also, with v3.9 and
later of the Linux Kernel, uImage isn't builtable anymore by default, so we
should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Taras Kondratiuk [Tue, 6 Aug 2013 13:16:50 +0000 (16:16 +0300)]
omap: emif: Set initial DDR PHY config first
Commit "OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon"
(
f40107345cbcd6e0d1747eda45e76c4e2a6df0db)
changed sequence to set final DDR PHY config register value at the beginning.
Looks like it was made by mistake and should be reverted.
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Masahiro Yamada [Mon, 5 Aug 2013 01:49:42 +0000 (10:49 +0900)]
ARM: omap24xx: remove remainders of dead board
Since Commit
7f5eef9 removed OMAP2420H4 support,
arm1136/omap24xx has not been used at all.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Naumann Andreas [Tue, 9 Jul 2013 07:43:17 +0000 (09:43 +0200)]
ARM: omap3: Implement dpll5 (HSUSB clk) workaround for OMAP36xx/AM/DM37xx according to errata sprz318e.
In chapter 'Advisory 2.1 USB Host Clock Drift Causes USB Spec Non-compliance in Certain Configurations' of the TI Errata it is recommended to use certain div/mult values for the DPLL5 clock setup.
So far u-boot used the old 34xx values, so I added the errata recommended values specificly for 36xx init only.
Also, the FSEL registers exist no longer, so removed them from init.
Tested this on a AM3703 board with 19.2MHz oscillator, which previously couldnt lock the dpll5 (kernel complained). As a consequence the EHCI USB port wasnt usable in U-Boot and kernel. With this patch, kernel panics disappear and USB working fine in u-boot and kernel.
Signed-off-by: Andreas Naumann <anaumann@ultratronik.de>
[trini: Add extern to <asm/arch-omap3/clock.h>
Signed-off-by: Tom Rini <trini@ti.com>
Ash Charles [Wed, 24 Jul 2013 19:22:35 +0000 (12:22 -0700)]
omap: overo: Use 200MHz SDRC timings for revision 1, 2 & 3 boards
Gumstix uses 200Mhz RAM on revision 1, 2 & 3 COMs, so use 200MHz
timings rather than 165MHz. Based on
6cf8bf44b1f8550e12f7f2a16e01890e5de8443d
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Steve Sakoman [Wed, 24 Jul 2013 19:22:34 +0000 (12:22 -0700)]
omap: overo: update support for Micron 1GB POP
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Enric Balletbo i Serra [Thu, 25 Jul 2013 07:27:40 +0000 (09:27 +0200)]
ARM: IGEP0033: Remove duplicate / unused #defines.
As config was originally based on am335x_evm.h we have also some
duplicate / unnused #defines.
Commit
15191c91 removed these #defines on various AM335x boards but not
for IGEP COM AQUILA. This patch simply removes them for this board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Enric Balletbo i Serra [Thu, 25 Jul 2013 07:27:39 +0000 (09:27 +0200)]
ARM: IGEP0033: Add support to boot from NAND.
Add to the default environment the possibily to boot from NAND using
a ubi rootfs. Also the partition scheme is set as follows:
Start Size
SPL : 0x00000000 0x00080000 (512KiB)
U-Boot : 0x00080000 0x00100000 (1MiB)
U-Boot Env : 0x00180000 0x00020000 (128KiB)
File System : 0x001C0000 -
The ubiboot script gets the kernel and the dtb file from the boot directory
of the File System.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Enric Balletbo i Serra [Thu, 25 Jul 2013 07:27:38 +0000 (09:27 +0200)]
ARM: IGEP0033: Remove CYGNUS name from header.
We will not use CYGNUS names for any IGEP COM based on AM335x processor,
so, to avoid confusion, remove from headers.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Enric Balletbò i Serra [Thu, 25 Jul 2013 07:27:37 +0000 (09:27 +0200)]
ARM: IGEP0033: Add support for Flattened Device Tree.
Now, the default kernel to boot the IGEP COM AQUILA is device tree based. As
old kernel is deprecated we should adapt the boot commands to use DTB files.
Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore
by default, so we should switch to use the bootz command.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Enric Balletbo i Serra [Thu, 25 Jul 2013 07:27:36 +0000 (09:27 +0200)]
ARM: IGEP0033: Remove undef of CONFIG_CMD_MEMTEST
After commit:
79cd2f814b1c75efd47161ac27f4cbebf768240f config_cmd_default.h: Remove CONFIG_CMD_MEMTEST
It's not necessary to undef the CONFIG_CMD_MEMTEST, so we can remove it from
configuration file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Lokesh Vutla [Tue, 30 Jul 2013 06:06:32 +0000 (11:36 +0530)]
ARM: AM43xx: Add config file
Add config file
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 30 Jul 2013 06:06:31 +0000 (11:36 +0530)]
ARM: AM43xx: Add build support
Add AM43xx support in the required places
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 30 Jul 2013 06:06:30 +0000 (11:36 +0530)]
ARM: OMAP: Add CONFIG_OMAP_COMMON
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 30 Jul 2013 06:06:29 +0000 (11:36 +0530)]
ARM: AM43xx: clocks: Add dpll and clock data
Add dpll and clock data for AM43xx
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 30 Jul 2013 06:06:28 +0000 (11:36 +0530)]
ARM: AM43xx: Add header files
Adding the following data:
-> Prcm structure
-> Base addresses
-> Pin mux structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 30 Jul 2013 06:06:27 +0000 (11:36 +0530)]
ARM: AM43xx: Add Board files
Add board specific information for AM43xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 30 Jul 2013 05:18:55 +0000 (10:48 +0530)]
musb: Disable extra prints
There are many musb prints in SPL and U-Boot log.
These prints are required only during musb debug.
So replacing printk with pr_debug in musb_core.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 30 Jul 2013 05:18:54 +0000 (10:48 +0530)]
ARM: AM33xx: Move s_init to a common place
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Lokesh Vutla [Tue, 30 Jul 2013 05:18:53 +0000 (10:48 +0530)]
ARM: AM33xx: Cleanup clocks layer
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Lokesh Vutla [Tue, 30 Jul 2013 05:18:52 +0000 (10:48 +0530)]
ARM: AM33xx: Cleanup dplls data
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Tom Rini [Wed, 14 Aug 2013 19:16:48 +0000 (15:16 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
York Sun [Wed, 14 Aug 2013 17:56:49 +0000 (10:56 -0700)]
include/fsl_usb.h: Cleanup license header
Replace license header with SPDX license identifier.
Replace GPL-2.0 with GPL-2.0+.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Po Liu [Thu, 16 May 2013 01:27:28 +0000 (09:27 +0800)]
powerpc/c29xpcie: add readme document for c29xpcie
Signed-off-by: Po Liu <Po.Liu@freescale.com>
ramneek mehresh [Mon, 5 Aug 2013 10:32:53 +0000 (16:02 +0530)]
powerpc/usb: Depricate usb_phy_type and usb_dr_mode uboot env variables
Remove getting values of usb mode and phy_type from "usb_dr_mode"
and "usb_phy_type" uboot env variables. Now, these are determined
only from hwconfig string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
ramneek mehresh [Mon, 5 Aug 2013 10:30:16 +0000 (16:00 +0530)]
fsl/usb: Move USB internal phy definitions to fsl_usb.h
fsl_usb.h file created to share data bewteen usb platform code
and usb ip driver. Internal phy structure definitions moved to
this file
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Wed, 31 Jul 2013 11:26:41 +0000 (16:56 +0530)]
powerpc/mpc85xx:Avoid hardcoded init for serdes block 1 & 2
It is not necessary for all processor to have serdes block 1 & 2.
They may have only one serdes block.
So, put serdes block 1 & 2 related code under defines
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Simon Glass [Wed, 7 Aug 2013 05:52:25 +0000 (22:52 -0700)]
tegra: Avoid using I2C prior to relocation
Tegra recently moved to the new I2C framework, which sets up I2C prior to
relocation, and prior to calling i2c_init_board(). This causes a crash on
Tegra boards.
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Rini [Tue, 13 Aug 2013 20:49:44 +0000 (16:49 -0400)]
Merge branch 'dcc' of git://denx.de/git/u-boot-microblaze
Tom Rini [Tue, 13 Aug 2013 13:14:02 +0000 (09:14 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Tom Rini [Tue, 13 Aug 2013 12:58:47 +0000 (08:58 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-mips
Daniel Schwierzeck [Sat, 12 Jan 2013 17:18:20 +0000 (18:18 +0100)]
MIPS: bootm: drop obsolete Qemu specific bootm implementation
The Qemu specific bootm implementation was intended for a special
Qemu target in Linux kernel. But this target has been dropped in
v2.6.25-rc1 by commit
302922e5f6901eb6f29c58539631f71b3d9746b8
Author: Ralf Baechle <ralf@linux-mips.org>
Date: Tue Jan 29 10:15:02 2008 +0000
[MIPS] Qemu: Remove platform.
The Qemu platform was originally implemented to have an easily supportable
platform until Qemu reaches a state where it emulates a real world system.
Since the latest release Qemu is capable of emulating the MIPSsim and
Malta platforms, so this goal has been reached. The Qemu plaform is also
rather underfeatured so less useful than a Malta emulation.
Thus the special bootm implementation is obsolete by now and can be
dropped. The Qemu support in U-Boot is going to be replaced by MIPS Malta
board support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Thu, 30 May 2013 17:04:20 +0000 (19:04 +0200)]
MIPS: bootm: add YAMON style Linux preparation/jump code for Qemu Malta
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Thu, 9 May 2013 15:10:06 +0000 (17:10 +0200)]
MIPS: bootm: add support for generic relocation of init ramdisks
All linux kernels after v2.6 require a page-aligned location of
an external init ramdisk. Enable CONFIG_SYS_BOOT_RAMDISK_HIGH to
support this with the generic U-Boot relocation code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Thu, 9 May 2013 15:10:06 +0000 (17:10 +0200)]
MIPS: bootm: refactor initialisation of kernel environment
Move initialisation of Linux environment to separate functions.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Thu, 9 May 2013 15:10:06 +0000 (17:10 +0200)]
MIPS: bootm: refactor initialisation of kernel cmdline
Move initialisation of Linux command line to separate functions.
Also add support for bootm subcommand 'cmdline'.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Thu, 9 May 2013 15:10:06 +0000 (17:10 +0200)]
MIPS: bootm: add support for LMB
This is required for init ramdisk relocation and device tree
support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Thu, 9 May 2013 15:10:06 +0000 (17:10 +0200)]
MIPS: bootm: optimize kernel entry call
Fix signature of kernel entry function. Mark the kernel entry
with __noreturn for better code optimisation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Thu, 9 May 2013 15:10:06 +0000 (17:10 +0200)]
MIPS: bootm: fix checkpatch.pl warnings
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Jagannadha Sutradharudu Teki [Sat, 3 Aug 2013 19:52:25 +0000 (01:22 +0530)]
serial: arm_dcc: Register with serial core
Register arm_dcc with drivers/serial/serial.c
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Jagannadha Sutradharudu Teki [Sat, 3 Aug 2013 19:52:24 +0000 (01:22 +0530)]
serial: arm_dcc: Remove stdio structure support
Removed stdio structure ops support on arm_dcc
driver, and need to register with serial core
so-that it can access like remianing serial drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Mon, 12 Aug 2013 22:06:30 +0000 (18:06 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-video
York Sun [Mon, 12 Aug 2013 21:57:12 +0000 (14:57 -0700)]
powerpc/mpc85xx: Cleanup license header in source files
Fix the license header introduced by the following patches
Add TWR-P10xx board support
Add T4240EMU target
IDT8T49N222A configuration code
Add C29x SoC support
Add support for C29XPCIE board
Signed-off-by: York Sun <yorksun@freescale.com>
Christian Gmeiner [Wed, 7 Aug 2013 07:22:33 +0000 (09:22 +0200)]
edid: rename struct member to fix two EDID_* macros
Without this change EDID_DETAILED_TIMING_VSYNC_OFFSET
and EDID_DETAILED_TIMING_VSYNC_PULSE_WIDTH macros can
not be used (compile error).
The fix is quite trivial: rename struct member to the
expected name.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Donghwa Lee [Mon, 5 Aug 2013 04:34:32 +0000 (13:34 +0900)]
exynos: video: change mipi dsi write function parameters correctly
This patch have changed mipi dsi write functions' parameters correctly
so that type cast operations were removed. And mipi dsi payload is
composed with array of panel commands to improve readability.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Marek Vasut [Tue, 30 Jul 2013 21:37:58 +0000 (23:37 +0200)]
video: Add small 4x6 font from Linux
This font is based on Linux drivers/video/console/font_mini_4x6.c as of commit:
commit
bcfbeecea11c15e243f076d37d637c2598aff4fe
Author: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Date: Sun Aug 12 15:05:10 2012 +0000
drivers: console: font_: Change a glyph from "broken bar" to "vertical line"
I removed these lines as they are useless in U-Boot:
#include <linux/font.h>
#define FONTDATAMAX 1536
Whole "const struct font_desc font_mini_4x6" block
This patch also adds a new configuration option to select this smaller font,
CONFIG_VIDEO_FONT_4X6 , but this is disabled by default. The default setting
is the regular "large" font.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Marek Vasut [Tue, 30 Jul 2013 21:37:57 +0000 (23:37 +0200)]
video: Encapsulate font in video_font_data.h
This patch moves all the font configuration values into video_font_data.h
so they are all in the right place with the font. The video_font.h now only
includes video_font_data.h and will allow us to select and include different
font once more fonts are added.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
[agust: fixed build warning for mcc200]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Stefan Roese [Sat, 22 Jun 2013 14:16:25 +0000 (16:16 +0200)]
mpc5200: Misc updates to a3m071 config header
This patch changes some features of the a3m071/a4m2k board support:
- Add bootcounter support
- Update MTD env default to correct values
- Add mtdparts to bootargs for mtd partitioning via kernel cmdline
- Added some default env variables for easy updating (kernel, dtb)
- Change README to the updated flash locations
Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Mon, 12 Aug 2013 12:54:32 +0000 (08:54 -0400)]
Merge branch 'fpga' of git://denx.de/git/u-boot-microblaze