oweals/openwrt.git
6 years agosunxi: NanoPi NEO Plus2 backport Gigabit Ethernet DT node
Antony Antony [Tue, 6 Mar 2018 19:08:42 +0000 (20:08 +0100)]
sunxi: NanoPi NEO Plus2 backport Gigabit Ethernet DT node

Kernel 4.16 commit 27d7f9297027

Signed-off-by: Antony Antony <antony@phenome.org>
6 years agomvebu: new subtarget cortex A53
Tomasz Maciej Nowak [Wed, 7 Mar 2018 21:10:02 +0000 (22:10 +0100)]
mvebu: new subtarget cortex A53

This commit introduces new subtarget for Marvell EBU Armada Cortex A53
processor based devices.

The first device is Globalscale ESPRESSObin. Some hardware specs:

SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53
     processor up to 1.2GHz
RAM: 512MB, 1GB or 2GB DDR3
Storage: SATA interface
         µSD card slot with footprint for an optional 4GB EMMC
         4MB SPI NOR flash for bootloader
Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports
Connectors: USB 3.0
            USB 2.0
            µUSB port connected to PL2303SA (USB to serial bridge
            controller) for UART access
Expansion: 2x 46-pin GPIO headers for accessories and shields with
           I2C, GPIOs, PWM, UART, SPI, MMC, etc
           MiniPCIe slot
Misc: Reset button, JTAG interface

Currently booting only from µSD card is supported.
The boards depending on date of dispatch can come with various U-Boot
versions. For the newest version 2017.03-armada-17.10 no manual
intervention should be needed to boot OpenWrt image. For the older ones
it's necessary to modify default U-Boot environment:

 1. Interrupt boot process to run U-Boot command line,

 2. Run following commands:
    (for version 2017.03-armada-17.06 and 2017.03-armada-17.08)
     setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000"
     saveenv

    (for version 2015.01-armada-17.02 and 2015.01-armada-17.04)
     setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait"
     setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}"
     saveenv

 3. Poweroff, insert SD card with OpenWrt image, boot and enjoy.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: Add subtarget for Cortex A9 build
Hauke Mehrtens [Wed, 7 Mar 2018 21:10:01 +0000 (22:10 +0100)]
mvebu: Add subtarget for Cortex A9 build

This is in preparation for adding a subtarget for the Cortex A53 later.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agomvebu: add support for Turris Omnia
Ryan Mounce [Fri, 2 Jun 2017 16:31:06 +0000 (02:01 +0930)]
mvebu: add support for Turris Omnia

Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.

An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.

Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.

Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.

Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem

Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv

Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.

Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
6 years agomvebu: generate ramdisk image by default
Ryan Mounce [Thu, 13 Jul 2017 14:41:22 +0000 (00:11 +0930)]
mvebu: generate ramdisk image by default

ramdisk images must be used in the installation process for upcoming
Turris Omnia support.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
6 years agomvebu: disable DSA DT nodes for boards using mvsw61xx
Ryan Mounce [Mon, 19 Feb 2018 14:01:34 +0000 (00:31 +1030)]
mvebu: disable DSA DT nodes for boards using mvsw61xx

As at this commit, DSA is not enabled in the kernel config for mvebu, so these
nodes have been ignored. In preparation for the first mvebu board using DSA,
disable these nodes for existing boards to avoid issues.

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
6 years agofirmware: ath10k-firmware: update QCA9984 firmware to 10.4-3.5.3-00053
Henryk Heisig [Sun, 18 Feb 2018 08:47:13 +0000 (09:47 +0100)]
firmware: ath10k-firmware: update QCA9984 firmware to 10.4-3.5.3-00053

This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.

The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.

Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
6 years agofirmware: ath10k-firmware: update to 2018-02-09
Henryk Heisig [Sat, 17 Feb 2018 10:26:23 +0000 (11:26 +0100)]
firmware: ath10k-firmware: update to 2018-02-09

This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
6 years agoutil-linux: added unshare and nsenter executables
Toni Uhlig [Sat, 3 Mar 2018 21:18:28 +0000 (22:18 +0100)]
util-linux: added unshare and nsenter executables

Signed-off-by: Toni Uhlig <matzeton@googlemail.com>
6 years agoiperf3: update to 3.5
Philip Prindeville [Fri, 2 Mar 2018 22:09:18 +0000 (15:09 -0700)]
iperf3: update to 3.5

Get rid of patches which are already upstream.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
6 years agoe2fsprogs: bump to 1.44.0
Ansuel Smith [Fri, 9 Mar 2018 01:29:58 +0000 (02:29 +0100)]
e2fsprogs: bump to 1.44.0

Fix compilation error

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
6 years agoopenvpn: update to 2.4.5
Magnus Kroken [Sat, 3 Mar 2018 00:11:07 +0000 (01:11 +0100)]
openvpn: update to 2.4.5

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agolinux-firmware: bump firmware for Intel Wireless 8260AC to version 31
Stijn Segers [Wed, 7 Mar 2018 21:25:12 +0000 (22:25 +0100)]
linux-firmware: bump firmware for Intel Wireless 8260AC to version 31

Bump the firmware for 8260AC and related hardware to version 31.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
6 years agokernel: bump 4.9 to 4.9.86
Koen Vandeputte [Mon, 5 Mar 2018 16:34:07 +0000 (17:34 +0100)]
kernel: bump 4.9 to 4.9.86

- Refreshed all patches
- Removed 1 patch which got upstreamed

Compile tested on: ar71xx (Rocket M5, Mikrotik RB2011)
Runtime tested on: ar71xx (Rocket M5, Mikrotik RB2011)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agokernel: bump to version 4.14.25
Kabuli Chana [Fri, 9 Mar 2018 17:33:04 +0000 (10:33 -0700)]
kernel: bump to version 4.14.25

compile/test target mvebu/rango

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
6 years agoar71xx: fix double registration of usb host mode devices, add usb client support...
Felix Fietkau [Fri, 9 Mar 2018 17:22:18 +0000 (18:22 +0100)]
ar71xx: fix double registration of usb host mode devices, add usb client support for qca955x

Only register the chipidea usb device if the strapping option indicates
device mode. If not, use the regular ehci platform driver.

Add qca955x device mode support, tested on 8devices Rambutan.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoinclue/image.mk: fix package installation for per-device rootfs
Matthias Schiffer [Fri, 9 Mar 2018 07:18:54 +0000 (08:18 +0100)]
inclue/image.mk: fix package installation for per-device rootfs

Fixes FS#1421.

Fixes: 2fbf669730bf ("imagebuilder: reuse rootfs preparation from rootfs.mk")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoebtables: update to latest git 2018-01-17
Hans Dedecker [Thu, 8 Mar 2018 17:23:25 +0000 (18:23 +0100)]
ebtables: update to latest git 2018-01-17

068ba95 Fix locking if LOCKDIR does not exist

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agouml: Remove 4.4 patches
Florian Fainelli [Sat, 16 Dec 2017 22:37:51 +0000 (14:37 -0800)]
uml: Remove 4.4 patches

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
6 years agofirewall: bump to git HEAD
Stijn Tintel [Fri, 2 Mar 2018 10:14:11 +0000 (11:14 +0100)]
firewall: bump to git HEAD

392811a ubus: let fw3_ubus_address() return the number of resolved addresses
359adcf options: emit an empty address item when resolving networks fails
503db4a zones: disable masq when resolving of all masq_src or masq_dest items failed
f50a524 helpers: implement explicit CT helper assignment support
a3ef503 zones: allow per-table log control
8ef12cb iptables: fix possible NULL pointer access on constructing rule masks

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years agobase-files: tune fragment queue thresholds for available system memory
Matthias Schiffer [Mon, 5 Mar 2018 08:13:53 +0000 (09:13 +0100)]
base-files: tune fragment queue thresholds for available system memory

The default fragment low/high thresholds are 3 and 4 MB. On devices with
only 32MB RAM, these settings may lead to OOM when many fragments that
cannot be reassembled are received. Decrease fragment low/high thresholds
to 384 and 512 kB on devices with less than 64 MB RAM.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agobcm53xx: include patch adding WZR-900DHP LEDs support
Rafał Miłecki [Wed, 7 Mar 2018 16:00:30 +0000 (17:00 +0100)]
bcm53xx: include patch adding WZR-900DHP LEDs support

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agoinclude/package-defaults.mk: fix default Build/Prepare with empty ./src
Matthias Schiffer [Tue, 6 Mar 2018 20:55:01 +0000 (21:55 +0100)]
include/package-defaults.mk: fix default Build/Prepare with empty ./src

Copying ./src/* would fail when src exists, but is empty or only contains
hidden files.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoinclude/image.mk: base package-list manifest on unprepared rootfs
Matthias Schiffer [Tue, 6 Mar 2018 13:42:37 +0000 (14:42 +0100)]
include/image.mk: base package-list manifest on unprepared rootfs

With CONFIG_CLEAN_IPKG, the prepared rootfs does not have a full opkg
status file.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoimagebuilder: remove split patch dirs from imagebuilder archive
Matthias Schiffer [Tue, 6 Mar 2018 20:50:05 +0000 (21:50 +0100)]
imagebuilder: remove split patch dirs from imagebuilder archive

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoimagebuilder: reuse rootfs preparation from rootfs.mk
Matthias Schiffer [Tue, 6 Mar 2018 08:38:29 +0000 (09:38 +0100)]
imagebuilder: reuse rootfs preparation from rootfs.mk

In addition to removing redundant code, this fixes various issues in
IB-generated images that have been fixed in prepare_rootfs before,
including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts
from FILES.

We also reuse the opkg macro and remove --force-... flags that have been
removed from rootfs.mk as well.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoinclude/rootfs.mk: pass additional files dir to prepare_rootfs as an argument
Matthias Schiffer [Tue, 6 Mar 2018 20:06:30 +0000 (21:06 +0100)]
include/rootfs.mk: pass additional files dir to prepare_rootfs as an argument

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoinclude/rootfs.mk: retain list of conffiles with CONFIG_CLEAN_IPKG
Matthias Schiffer [Tue, 6 Mar 2018 13:29:46 +0000 (14:29 +0100)]
include/rootfs.mk: retain list of conffiles with CONFIG_CLEAN_IPKG

/usr/lib/opkg/status must not be removed completely, otherwise the
packages' conffile lists will be missing. Replace it with a reduced version
only containing the conffile entries.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoinclude/rootfs.mk: do not remove opkg prerm scripts during rootfs preparation
Matthias Schiffer [Tue, 6 Mar 2018 07:49:14 +0000 (08:49 +0100)]
include/rootfs.mk: do not remove opkg prerm scripts during rootfs preparation

When a user removes a preinstalled opkg package, the package's prerm script
(and in particular our default_prerm) should run.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agobase-files: sysupgrade: do not rely on opkg to list changed conffiles
Matthias Schiffer [Tue, 6 Mar 2018 07:25:32 +0000 (08:25 +0100)]
base-files: sysupgrade: do not rely on opkg to list changed conffiles

Many packages use the opkg conffiles field to list configuration files that
are to be retained on upgrades. Make this work on systems without opkg.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agolantiq/xrx200: add usif support to dts files
Martin Schiller [Fri, 23 Feb 2018 13:15:49 +0000 (14:15 +0100)]
lantiq/xrx200: add usif support to dts files

The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead,
there is an USIF module which can either be an UART or a
SPI Controller.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
6 years agolantiq: ltq-adsl: deactivate ASLR support
Mathias Kresin [Tue, 6 Mar 2018 18:43:40 +0000 (19:43 +0100)]
lantiq: ltq-adsl: deactivate ASLR support

The package still leaks some user space linker options into the kernel
space. This breaks the build when ASLR is activated, deactivate it for
now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: mt7620n: enable port 4 as EPHY by default
Giuseppe Lippolis [Sat, 24 Feb 2018 08:45:12 +0000 (09:45 +0100)]
ramips: mt7620n: enable port 4 as EPHY by default

According to the datasheet the mt7620n have a fixed switch configuration
with 5 ephy (10/100) port. No RGMII configuration is possible.

Drop the mdio node as well. Without RGMII, the mdio node doesn't make any
sense

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[drop mdio node, enable port4 by default]
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: mt7620: power up ephy port 4
Pawel Dembicki [Mon, 19 Feb 2018 21:15:56 +0000 (22:15 +0100)]
ramips: mt7620: power up ephy port 4

In some boards port 4 of mt7620 switch is powered down in bootloader
configuration as lan/wan package leak mitigation.

Reset ephy port 4 to default settings to power up the port.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[clarify issue in commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agowireguard: bump to 20180304
Jason A. Donenfeld [Mon, 5 Mar 2018 10:31:53 +0000 (11:31 +0100)]
wireguard: bump to 20180304

7c0d711 version: bump snapshot
b6a5cc0 contrib: add extract-handshakes kprobe example
37dc953 wg-quick: if resolvconf/run/iface exists, use it
1f9be19 wg-quick: if resolvconf/interface-order exists, use it
4d2d395 noise: align static_identity keys
14395d2 compat: use correct -include path
38c6d8f noise: fix function prototype
302d0c0 global: in gnu code, use un-underscored asm
ff4e06b messages: MESSAGE_TOTAL is unused
ea81962 crypto: read only after init
e35f409 Kconfig: require DST_CACHE explicitly
9d5baf7 Revert "contrib: keygen-html: rewrite in pure javascript"
6e09a46 contrib: keygen-html: rewrite in pure javascript
e0af0f4 compat: workaround netlink refcount bug
ec65415 contrib: embedded-wg-library: add key generation functions
06099b8 allowedips: fix comment style
ce04251 contrib: embedded-wg-library: add ability to add and del interfaces
7403191 queueing: skb_reset: mark as xnet

Changes:

* queueing: skb_reset: mark as xnet

This allows cgroups to classify packets.

* contrib: embedded-wg-library: add ability to add and del interfaces
* contrib: embedded-wg-library: add key generation functions

The embeddable library gains a few extra tricks, for people implementing
plugins for various network managers.

* crypto: read only after init
* allowedips: fix comment style
* messages: MESSAGE_TOTAL is unused
* global: in gnu code, use un-underscored asm
* noise: fix function prototype

Small cleanups.

* compat: workaround netlink refcount bug

An upstream refcounting bug meant that in certain situations it became
impossible to unload the module. So, we work around it in the compat code. The
problem has been fixed in 4.16.

* contrib: keygen-html: rewrite in pure javascript
* Revert "contrib: keygen-html: rewrite in pure javascript"

We nearly moved away from emscripten'ing the fiat32 code, but the resultant
floating point javascript was just too terrifying.

* Kconfig: require DST_CACHE explicitly

Required for certain frankenkernels.

* compat: use correct -include path

Fixes certain out-of-tree build systems.

* noise: align static_identity keys

Gives us better alignment of private keys.

* wg-quick: if resolvconf/interface-order exists, use it
* wg-quick: if resolvconf/run/iface exists, use it

Better compatibility with Debian's resolvconf.

* contrib: add extract-handshakes kprobe example

Small utility for extracting ephemeral key data from the kernel's memory.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (git log --oneline description)
6 years agonghttp2: bump to 1.31.0
Hans Dedecker [Mon, 5 Mar 2018 09:23:09 +0000 (10:23 +0100)]
nghttp2: bump to 1.31.0

6e744662 Update bash_completion
478eac09 Update manual pages
88e2029e Bump up version number to 1.31.0, LT revision to 30:0:16
45d76cf5 nghttpx: Close listening socket on graceful shutdown
54573f28 Merge pull request #1137 from nghttp2/session-set-user-data
17793e99 Add nghttp2_session_set_user_data() public API function
5eac3c90 Update manual pages
e70195ae nghttpx: Update doc
fe51e7fa Merge pull request #1130 from nghttp2/avoid-inet_pton-macro
eb951c2c src: Define nghttp2_inet_pton wrapper to avoid inet_pton macro
39f0ce7c Merge pull request #1126 from nghttp2/nghttpx-expired-client-cert
65157811 Merge pull request #1123 from nghttp2/mruby-client-cert-not-before-after
e8af7afc nghttpx: Add an option to accept expired client certificate
38abfd18 nghttpx: Add mruby tls_client_not_before, and tls_client_not_after
ff3edc09 nghttpx: Fix potential memory leak
0bb15406 Bump up version number to 1.31.0-DEV

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agomt76: update to the latest version
Felix Fietkau [Mon, 26 Feb 2018 21:15:24 +0000 (22:15 +0100)]
mt76: update to the latest version

cda627f mt76: add missing VHT maximum A-MPDU length capability
ffa2069 mt76: fix potential sleep in atomic context

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agokernel: remove an old kernel compatibility line from module packaging
Felix Fietkau [Thu, 22 Feb 2018 11:16:19 +0000 (12:16 +0100)]
kernel: remove an old kernel compatibility line from module packaging

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoar71xx: fix mii bus irq assignment
Felix Fietkau [Sat, 3 Mar 2018 11:23:51 +0000 (12:23 +0100)]
ar71xx: fix mii bus irq assignment

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoar71xx: remove pdata->fifo_cfg*
Felix Fietkau [Fri, 2 Mar 2018 20:30:10 +0000 (21:30 +0100)]
ar71xx: remove pdata->fifo_cfg*

The values are the same for all chipsets that use it

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomac80211: avoid sampling rates that are too slow, improves throughput
Felix Fietkau [Sat, 3 Mar 2018 17:51:49 +0000 (18:51 +0100)]
mac80211: avoid sampling rates that are too slow, improves throughput

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agokernel: bump 4.4 to 4.4.119
Stijn Segers [Fri, 2 Mar 2018 07:31:03 +0000 (08:31 +0100)]
kernel: bump 4.4 to 4.4.119

This bumps the 4.4. kernel in master to 4.4.119.
Includes more Meltdown & Spectre mitigation.

* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)).

Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant.

Compile-tested on: ar71xx & oxnas.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Rosen Penev <rosenp@gmail.com>
6 years agokernel: bump 4.9 to 4.9.85
Magnus Kroken [Sat, 3 Mar 2018 00:12:07 +0000 (01:12 +0100)]
kernel: bump 4.9 to 4.9.85

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
6 years agolantiq: Deactivate ASLR support for some applications
Hauke Mehrtens [Sat, 3 Mar 2018 00:21:08 +0000 (01:21 +0100)]
lantiq: Deactivate ASLR support for some applications

The lantiq components still leak some user space linker options into the
kernel space. This breaks with build when ASLR is activated, deactivate
it for now on these packages.

Fixes: FS#1391
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agolantiq: ltq-vmmc: Do not leak user space CFLAGS into kernel space
Hauke Mehrtens [Fri, 2 Mar 2018 23:52:16 +0000 (00:52 +0100)]
lantiq: ltq-vmmc: Do not leak user space CFLAGS into kernel space

Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agolantiq: ltq-tapi: Do not leak user space CFLAGS into kernel space
Hauke Mehrtens [Fri, 2 Mar 2018 23:51:40 +0000 (00:51 +0100)]
lantiq: ltq-tapi: Do not leak user space CFLAGS into kernel space

Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agolantiq: ltq-adsl: Do not leak user space CFLAGS into kernel space
Hauke Mehrtens [Sat, 3 Mar 2018 00:38:50 +0000 (01:38 +0100)]
lantiq: ltq-adsl: Do not leak user space CFLAGS into kernel space

Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agolantiq: ltq-vdsl: Do not leak user space CFLAGS into kernel space
Hauke Mehrtens [Fri, 2 Mar 2018 23:25:06 +0000 (00:25 +0100)]
lantiq: ltq-vdsl: Do not leak user space CFLAGS into kernel space

Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agolantiq: ltq-vdsl-mei: Do not leak user space CFLAGS into kernel space
Hauke Mehrtens [Fri, 2 Mar 2018 23:23:55 +0000 (00:23 +0100)]
lantiq: ltq-vdsl-mei: Do not leak user space CFLAGS into kernel space

Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.

This decreases the size of the ipk file from 87589 bytes to 81267 bytes.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agolantiq: ltq-ifxos: Do not force O3 build any more
Hauke Mehrtens [Fri, 2 Mar 2018 23:22:49 +0000 (00:22 +0100)]
lantiq: ltq-ifxos: Do not force O3 build any more

Do not force to build with O3 optimization any more, but take what was
selected by the OpenWrt build system.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agolantiq: ltq-ifxos: activate build with mips16
Hauke Mehrtens [Fri, 2 Mar 2018 23:20:43 +0000 (00:20 +0100)]
lantiq: ltq-ifxos: activate build with mips16

The build process does not leak the user space cflags into the kernel
build process any more, this allows to activate MIPS16 builds.
This was fixed with some update of ifxos.

This decreases size of the  libifxos.a and the ltq-vdsl-app
old:
78320 libifxos.a
44383 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk

new:
66852 libifxos.a
43506 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agokernel: generic: Add kernel configuration options
Hauke Mehrtens [Fri, 2 Mar 2018 21:32:13 +0000 (22:32 +0100)]
kernel: generic: Add kernel configuration options

These options are needed for the mvebu arm64 target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agokernel: bump 4.14 to 4.14.23
Stijn Segers [Wed, 28 Feb 2018 21:53:37 +0000 (22:53 +0100)]
kernel: bump 4.14 to 4.14.23

This patch bumps the 4.14 kernel to .23.
- Refreshed patches.
- Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream.
- Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed,
  the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes.

Compile-tested on: ramips/mt7621, x86/64
Run-tested on: ramips/mt7621, x86/64

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
6 years agomvebu: base-files: moving on from net-tools
Tomasz Maciej Nowak [Wed, 24 Jan 2018 15:41:32 +0000 (16:41 +0100)]
mvebu: base-files: moving on from net-tools

Remove dependency on net-tools, replacing calls to ifconfig with iproute
equivalent, in functions changing interface MAC addresses.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: rename clearfog sysupgrade script and functions
Tomasz Maciej Nowak [Wed, 24 Jan 2018 15:39:48 +0000 (16:39 +0100)]
mvebu: rename clearfog sysupgrade script and functions

Cosmetic name change of ClearFog sysupgrade script and its functions to
more generic sdcard. This way it won't be confusing for other future
device additions.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: remove fs declaration in mount commands
Tomasz Maciej Nowak [Wed, 24 Jan 2018 23:04:56 +0000 (00:04 +0100)]
mvebu: remove fs declaration in mount commands

Allows to have other file system for boot partition without breaking
sysupgrade.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: unify boot.scr creation
Tomasz Maciej Nowak [Wed, 14 Feb 2018 16:34:38 +0000 (17:34 +0100)]
mvebu: unify boot.scr creation

Unify boot.scr generation so Makefile for device image generation won't
grow without a reason. Also make boot-scr step optional.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: make sdcard bootloader option configurable
Tomasz Maciej Nowak [Wed, 14 Feb 2018 16:28:09 +0000 (17:28 +0100)]
mvebu: make sdcard bootloader option configurable

Remove the necessity for boot loader from SD card image creation process
and make it configurable.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: fix partition type and signature for sdcard
Tomasz Maciej Nowak [Wed, 24 Jan 2018 14:32:58 +0000 (15:32 +0100)]
mvebu: fix partition type and signature for sdcard

Previously the partition signature was assigned from provided type. Now
both are corrected wherein signature is always generated from
SOURCE_DATE_EPOCH. With that the root file system can be identified
by PARTUUID string, without relying on static declaration of device node.
This commit also does some cosmetics, removing trailing whitespace and
replacing spaces with tab.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: remove redefinition of image name for clearfog
Tomasz Maciej Nowak [Wed, 14 Feb 2018 16:20:00 +0000 (17:20 +0100)]
mvebu: remove redefinition of image name for clearfog

The IMAGE_NAME redefinition causes overwriting of generated SD card
image when multiple root file system types are selected. In result only
single SD card image is generated. This commit fixes this behaviour.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: clearfog: use partition uuid for root= bootarg
Josua Mayer [Thu, 19 Oct 2017 07:22:11 +0000 (09:22 +0200)]
mvebu: clearfog: use partition uuid for root= bootarg

U-Boot already knows where it found the boot.scr, and
figuring out the partition UUID becomes trivial at this point.
This change allows booting OpenWrt from whatever storage it has been
flashed to: SD card, eMMC, USB disk or SATA disk.

Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
[replace lede with openwrt, redact commit message]
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
6 years agomvebu: Use kernel 4.14 by default
Hauke Mehrtens [Thu, 1 Mar 2018 20:45:24 +0000 (21:45 +0100)]
mvebu: Use kernel 4.14 by default

I am not aware of any regressions in kernel 4.14 compared to kernel 4.9.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agomvebu: activate more workarounds for ARM erratas
Hauke Mehrtens [Sun, 18 Feb 2018 17:57:02 +0000 (18:57 +0100)]
mvebu: activate more workarounds for ARM erratas

The Armada XP uses a Marvell PJ4Bv7 Processor for which already one
workaround for an errata is activated.
The Armada 285 uses a Cortex A9 r4p1 for which the Linux kernel provides
a workaround for ERRATA_764369, activate this.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agomwlwifi: Update to version 10.3.4.0-20180226
Kabuli Chana [Mon, 26 Feb 2018 04:46:55 +0000 (21:46 -0700)]
mwlwifi: Update to version 10.3.4.0-20180226

move to latest version, address vfs_write issue

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
6 years agokernel: generic: Move config option to generic
Hauke Mehrtens [Thu, 1 Mar 2018 20:48:28 +0000 (21:48 +0100)]
kernel: generic: Move config option to generic

This is deactivated in all targets using the DSA switch driver with
kernel 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agogre: squash grev4 and grev6 packages into gre (FS#1399)
Hans Dedecker [Fri, 2 Mar 2018 13:28:43 +0000 (14:28 +0100)]
gre: squash grev4 and grev6 packages into gre (FS#1399)

The split-up into packages gre, grev4 and grev6 causes confusion for the
users as reported in FS#1399.
As IPv4 and IPv6 are considered now as bundled; squash the grev4 and grev6
packages into the gre package and let gre provide both grev4 and grev6.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agonetifd: add udhcpc link check to dhcp shell handler script
Hans Dedecker [Thu, 1 Mar 2018 17:38:55 +0000 (18:38 +0100)]
netifd: add udhcpc link check to dhcp shell handler script

Fixes the assumption the busybox udhcpc applet is always enabled; in case
the symbolic link check fails the DHCP shell handler script will exit and
as result the DHCP protocol handler will not be registered in netifd.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agomac80211: brcmfmac: better logging of firmware api errors
Rafał Miłecki [Thu, 1 Mar 2018 17:45:10 +0000 (18:45 +0100)]
mac80211: brcmfmac: better logging of firmware api errors

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: brcmfmac: backport remaining changes from 4.16
Rafał Miłecki [Thu, 1 Mar 2018 17:36:04 +0000 (18:36 +0100)]
mac80211: brcmfmac: backport remaining changes from 4.16

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: brcmfmac: enlarge caps buffer & final sdio restructuring
Rafał Miłecki [Thu, 1 Mar 2018 17:22:51 +0000 (18:22 +0100)]
mac80211: brcmfmac: enlarge caps buffer & final sdio restructuring

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: brcmfmac: restructuring sdio access functions - take 2
Rafał Miłecki [Thu, 1 Mar 2018 17:15:43 +0000 (18:15 +0100)]
mac80211: brcmfmac: restructuring sdio access functions - take 2

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: brcmfmac: restructuring sdio access functions
Rafał Miłecki [Thu, 1 Mar 2018 17:00:19 +0000 (18:00 +0100)]
mac80211: brcmfmac: restructuring sdio access functions

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: brcmfmac: backport remaining changes from 4.15
Rafał Miłecki [Thu, 1 Mar 2018 14:08:25 +0000 (15:08 +0100)]
mac80211: brcmfmac: backport remaining changes from 4.15

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: brcmfmac: firmware halt and scan cleanup
Rafał Miłecki [Thu, 1 Mar 2018 13:55:08 +0000 (14:55 +0100)]
mac80211: brcmfmac: firmware halt and scan cleanup

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: reorder patches putting backports first
Rafał Miłecki [Thu, 1 Mar 2018 13:46:34 +0000 (14:46 +0100)]
mac80211: reorder patches putting backports first

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agomac80211: add a missing check to the last minstrel fix
Felix Fietkau [Thu, 1 Mar 2018 13:43:56 +0000 (14:43 +0100)]
mac80211: add a missing check to the last minstrel fix

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomac80211: rename patches accepted upstream
Rafał Miłecki [Thu, 1 Mar 2018 11:32:07 +0000 (12:32 +0100)]
mac80211: rename patches accepted upstream

This is to simplify maintenance. It's easy to say now which patches need
some extra work and/or sending upstream. Updating to newer backports
should be also simpler with this.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agoRevert "ath: do not apply broken power limits with ATH_USER_REGD"
Felix Fietkau [Wed, 28 Feb 2018 20:10:32 +0000 (21:10 +0100)]
Revert "ath: do not apply broken power limits with ATH_USER_REGD"

This reverts commit 79a768a90fa94c0a38c9def1992cc974c091e286.
Some devices can go over their power limits with this commit, so this
needs to be handled on a case by case basis instead

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomac80211: update the A-MSDU fast-rx patch to the latest version
Felix Fietkau [Wed, 28 Feb 2018 20:14:07 +0000 (21:14 +0100)]
mac80211: update the A-MSDU fast-rx patch to the latest version

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomac80211: add more minstrel fixes
Felix Fietkau [Thu, 1 Mar 2018 12:34:41 +0000 (13:34 +0100)]
mac80211: add more minstrel fixes

Improves 2.4 GHz throughput

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomac80211: fix regression introduced by the recent minstrel changes
Felix Fietkau [Thu, 1 Mar 2018 10:59:47 +0000 (11:59 +0100)]
mac80211: fix regression introduced by the recent minstrel changes

The cck rates array needs to be initialized for both the minstrel and
the minstrel_ht variant

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agobase-files: fix off-by-one in counting seconds for factory reset
Rafał Miłecki [Tue, 27 Feb 2018 15:44:25 +0000 (16:44 +0100)]
base-files: fix off-by-one in counting seconds for factory reset

There was a mismatch between indicating factory reset and code actually
starting it. After 5 seconds status LED started blinking rapidly letting
user know it's ready to release reset button. In practice button had to
stay pressed for another second in order to relly start the process.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agoar71xx: fix build with ag71xx debugfs support enabled
Felix Fietkau [Wed, 28 Feb 2018 12:57:58 +0000 (13:57 +0100)]
ar71xx: fix build with ag71xx debugfs support enabled

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoiw: update to version 4.14
Felix Fietkau [Sat, 24 Feb 2018 10:43:28 +0000 (11:43 +0100)]
iw: update to version 4.14

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomac80211: add an optimization for fast-rx support
Felix Fietkau [Mon, 26 Feb 2018 21:13:44 +0000 (22:13 +0100)]
mac80211: add an optimization for fast-rx support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agonetifd: update to the latest version, rewrite RPS/XPS handling
Felix Fietkau [Mon, 26 Feb 2018 11:30:28 +0000 (12:30 +0100)]
netifd: update to the latest version, rewrite RPS/XPS handling

Remove RPS/XPS support from netifd core, move the logic to a hotplug
script that uses a different policy which provides better performance
and more fairness across flows

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoag71xx: Move timestamp struct member outside of struct.
Rosen Penev [Wed, 7 Feb 2018 21:57:30 +0000 (13:57 -0800)]
ag71xx: Move timestamp struct member outside of struct.

With this change, the timestamp variable is only used in ag71xx_check_dma_stuck. Small tx speedup.

Based on a Qualcomm commit. ag->timestamp = jiffies was not replaced with netif_trans_update(dev) because of this quote:

It should be noted that after this series several instances
of netif_trans_update() are useless (if they occur in
.ndo_start_xmit and driver doesn't set LLTX flag -- stack already
did an update).

From: http://lists.openwall.net/netdev/2016/05/03/87

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agokernel: kmod-geneve: kmod for Geneve tunneling
Yousong Zhou [Tue, 13 Feb 2018 03:20:57 +0000 (11:20 +0800)]
kernel: kmod-geneve: kmod for Geneve tunneling

This will be required for Open vSwitch geneve tunneling support

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
6 years agoramips: fix spurious IRQ7 events when using perf on 4.14
Felix Fietkau [Tue, 27 Feb 2018 14:09:43 +0000 (15:09 +0100)]
ramips: fix spurious IRQ7 events when using perf on 4.14

Upstream handling of MIPS CPU IRQs is rather hackish and the interrupts
are being enabled unconditionally in various places because of legacy
code.
Performance counter events are routed both through the GIC and through
legacy CPU IRQ7 events, causing spurious interrupts.

Fix this by disabling IRQ7 when trying to access the performance counter
IRQ.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agobcm53xx: fix fallback code for picking status LED
Rafał Miłecki [Tue, 27 Feb 2018 15:49:31 +0000 (16:49 +0100)]
bcm53xx: fix fallback code for picking status LED

Looking for a wrong LED file name was stopping this code from find any
LED. This affects devices with only a red/amber power LED.

Fixes: 3aaee1ba023ac ("bcm53xx: failsafe support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agonetifd: support DHCP sendopts as list options
Hans Dedecker [Sat, 24 Feb 2018 15:52:38 +0000 (16:52 +0100)]
netifd: support DHCP sendopts as list options

Support config in the form of ....
add_list sendopts=router:10.10.10.2
add_list sendopts=nissrv:20.20.20.2
add_list sendopts=0x7D:abba

This allows to configure sendopts having white spaces as option value

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoRevert "ramips: improve NAPI polling to increase GRO batch size" (fixes FS#1333)
Felix Fietkau [Tue, 27 Feb 2018 08:41:59 +0000 (09:41 +0100)]
Revert "ramips: improve NAPI polling to increase GRO batch size" (fixes FS#1333)

This reverts commit 968b8616127a52fe5baff20a1f29ff49ade26bc2.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agotoolchain: fix selecting older gcc versions for x86
Felix Fietkau [Tue, 27 Feb 2018 08:00:52 +0000 (09:00 +0100)]
toolchain: fix selecting older gcc versions for x86

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agokernel: m25p80: allow fallback from spi_flash_read to regular SPI transfer
Felix Fietkau [Fri, 23 Feb 2018 16:33:21 +0000 (17:33 +0100)]
kernel: m25p80: allow fallback from spi_flash_read to regular SPI transfer

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agogcc: merge upstream fix for PR 83496 (fixes FS#814)
Felix Fietkau [Sun, 25 Feb 2018 19:25:20 +0000 (20:25 +0100)]
gcc: merge upstream fix for PR 83496 (fixes FS#814)

This bug was causing miscompiled code related to branch delay slots

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agogcc: refresh patches for version 7.3.0
Felix Fietkau [Sun, 25 Feb 2018 19:24:52 +0000 (20:24 +0100)]
gcc: refresh patches for version 7.3.0

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agoiptables: fix compile with kernel 3.18
Hauke Mehrtens [Mon, 26 Feb 2018 16:49:37 +0000 (17:49 +0100)]
iptables: fix compile with kernel 3.18

This fixes a compile bug found by build bot with kernel 3.18

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6 years agokernel: generic: add 4.14 config option
Hans Dedecker [Mon, 26 Feb 2018 15:32:54 +0000 (16:32 +0100)]
kernel: generic: add 4.14 config option

When CGROUPS is enabled the new option CONFIG_CGROUP_NET_CLASSID is
selectable and not handled.
Add this option to the 4.14 kernel configuration.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agokernel: package efivarfs module
Alif M. Ahmad [Sun, 25 Feb 2018 03:18:41 +0000 (03:18 +0000)]
kernel: package efivarfs module

With this, `mount -t efivarfs` is available and tools such as efitools
and efibootmgr will be usable.

Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
[daniel@makrotopia.org: some whitespace fixes, match From: with SoB]

6 years agosunxi: Add support for Xunlong Orange Pi PC
Vitalij Alshevsky [Sun, 25 Feb 2018 18:12:49 +0000 (21:12 +0300)]
sunxi: Add support for Xunlong Orange Pi PC

CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.3 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 1GB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard: Network 10/100M Ethernet RJ45
Onboard header pinout: SPI, I2C, 1-WIRE
USB 2.0: Three USB 2.0 HOST, One USB 2.0 OTG
Buttons: Power Button(SW4)
Debug TTL UART: ..DC-IN.. >[GND][RX][TX] ..HDMI..

Signed-off-by: Vitalij Alshevsky <v_alshevsky@tut.by>