oweals/openwrt.git
6 years agoar71xx: fix USB switch to mPCIE for Mikrotik rb91x boards
Koen Vandeputte [Thu, 7 Jun 2018 13:59:26 +0000 (15:59 +0200)]
ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boards

Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.

Toggling a gpio selects the output to which USB is connected.

Since kernel 4.9, gpio base is rounded up to a value of 32.

Commit 65da6f9ca164 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.

But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.

Switching the USB port to mPCIe now shows my modem is correctly discovered again:

[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11

Fixes: 65da6f9ca164 ("ar71xx: fix secondary gpio controller base values")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
6 years agoimx-uuc: updated to latest git HEAD
Krystian Kozak [Sun, 27 May 2018 20:54:04 +0000 (22:54 +0200)]
imx-uuc: updated to latest git HEAD

8e29d86 linuxrc: remove superfluous shebang line
12d2045 gitignore: remove Windows stuff
57d8969 Add travis hint
8edf4cc sdimage: use fsync before closing the device (fixes #1)
d395b31 uuc: fix some compiler warnings

Signed-off-by: Krystian Kozak <krystian.kozak20@gmail.com>
6 years agobusybox: udhcpc: no MSG_DONTROUTE when sending packet
Adi Shammout [Wed, 6 Jun 2018 19:53:24 +0000 (22:53 +0300)]
busybox: udhcpc: no MSG_DONTROUTE when sending packet

This reverts a change made in Sep 2017 [1] which introduced
MSG_DONTROUTE flag to prevent udhcpc from reaching out to servers on a
different subnet. That change violates RFC2131 by forcing fully
configured clients, who got their configurations through an offer
relayed by a DHCP relay, from renewing through a unicast request
directly to the DHCP server, resulting in the client resorting to
boradcasting lease extension requests instead of unicasting them,
further breaking RFC2131.

The problem with MSG_DONTROUTE appears when talking to a properly
configured DHCP server that rejects non-compliant requests. Such server
will reject lease extension attempts sent via broadcast rather than
unicast, as is the case with Finnish ISPs Telia and DNA as well as
Estonian ISP Starman. Once the lease expires without renewal, udhcpc
enters init mode, taking down the interfaces with it, and thus causing
interruption on every lease expiry. On some ISPs (such as the ones
mentioned above) that can be once every 10-20 minutes. The interruptions
appear in the logs as such:
----
udhcpc: sending renew to x.x.x.x
udhcpc: send: Network unreachable
udhcpc: sending renew to 0.0.0.0
udhcpc: sending renew to 0.0.0.0
...
udhcpc: lease lost, entering init state
Interface 'wan' has lost the connection
Interface 'wan' is now down
Network alias 'eth0' link is down
udhcpc: sending select for y.y.y.y
udhcpc: lease of y.y.y.y obtained, lease time 1200
Network alias 'eth0' link is up
Interface 'wan' is now up
----

During lease extension, a fully configured client should be able to
reach out to the server from which it recieved the lease for extension,
regardless in which network it is; that's up to the gateway to find. [2]
This patch ensures that.

[1]
http://lists.busybox.net/pipermail/busybox-cvs/2017-September/037402.html
[2]
https://www.netmanias.com/en/post/techdocs/6000/dhcp-network-protocol/
understanding-dhcp-relay-agents

Signed-off-by: Adi Shammout <adi.shammout@outlook.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
6 years agologd: create log directory for log_file
Karl Palsson [Thu, 22 Feb 2018 11:09:53 +0000 (11:09 +0000)]
logd: create log directory for log_file

If log_file is specified, make sure its directory exists.

Signed-off-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
6 years agoath79: fix qca956x SoC boot
Lucian Cristian [Sun, 3 Jun 2018 23:09:15 +0000 (02:09 +0300)]
ath79: fix qca956x SoC boot

based on old ar71xx irq.c driver

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 years agoar71xx: add support for OCEDO Koala
David Bauer [Tue, 29 May 2018 15:00:53 +0000 (17:00 +0200)]
ar71xx: add support for OCEDO Koala

This commit adds support for the OCEDO Koala

SOC: Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
6 years agohostapd: make cli treat UNKNOWN COMMAND as failing
Denton Gentry [Wed, 30 May 2018 15:05:42 +0000 (15:05 +0000)]
hostapd: make cli treat UNKNOWN COMMAND as failing

Avoid infinite loop at 100% CPU when running hostapd_cli
if CONFIG_CTRL_IFACE_MIB is not defined.

  _newselect(4, [3], NULL, NULL, ...)
  recvfrom(3, "UNKNOWN COMMAND\n", 4095, 0, NULL, NULL) = 16
  sendto(3, "STA-NEXT UNKNOWN COMMAND", 24, 0, NULL, 0) = 24

Signed-off-by: Denton Gentry <denny@geekhold.com>
6 years agoipq806x: Enlarge R7800 flash - use netgear partition
Hannu Nyman [Sun, 3 Jun 2018 13:33:15 +0000 (16:33 +0300)]
ipq806x: Enlarge R7800 flash - use netgear partition

Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.

Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.

In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.

Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit

Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52

Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
6 years agoipq806x: Limit NR_CPUS to 2
Rosen Penev [Thu, 7 Jun 2018 01:33:59 +0000 (18:33 -0700)]
ipq806x: Limit NR_CPUS to 2

ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:

RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agoethtool: Update to 4.16
Rosen Penev [Thu, 7 Jun 2018 01:22:28 +0000 (18:22 -0700)]
ethtool: Update to 4.16

Tested on Turris Omnia (mvebu).

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agoiperf: Update to 2.0.11
Rosen Penev [Thu, 7 Jun 2018 01:22:27 +0000 (18:22 -0700)]
iperf: Update to 2.0.11

Tested on Turris Omnia (mvebu).

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agogdb: Update to 8.1
Rosen Penev [Thu, 7 Jun 2018 01:22:26 +0000 (18:22 -0700)]
gdb: Update to 8.1

Tested on Turris Omnia (mvebu).

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agostrace: Update to 4.22
Rosen Penev [Thu, 7 Jun 2018 01:22:25 +0000 (18:22 -0700)]
strace: Update to 4.22

SourceForge is deprecated according to upstream, so switch to main site
for downloads.

Tested on Turris Omnia (mvebu).

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agokernel: bump 4.9 to 4.9.106
Koen Vandeputte [Wed, 6 Jun 2018 13:22:05 +0000 (15:22 +0200)]
kernel: bump 4.9 to 4.9.106

Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agoath79: add WLAN, Ethernet-Switch with LAN/WAN and Status LED to Dorin
Catrinel Catrinescu [Tue, 5 Jun 2018 14:56:48 +0000 (16:56 +0200)]
ath79: add WLAN, Ethernet-Switch with LAN/WAN and Status LED to Dorin

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
6 years agozynq: remove support for kernel 4.4
Luis Araneda [Sun, 13 May 2018 23:48:53 +0000 (19:48 -0400)]
zynq: remove support for kernel 4.4

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agozynq: switch to kernel 4.14
Luis Araneda [Sun, 13 May 2018 23:45:58 +0000 (19:45 -0400)]
zynq: switch to kernel 4.14

Also, remove the source-only qualifier

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agozynq: refresh kernel 4.14 configuration
Luis Araneda [Sun, 13 May 2018 23:39:36 +0000 (19:39 -0400)]
zynq: refresh kernel 4.14 configuration

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agozynq: copy config to kernel 4.14
Luis Araneda [Sun, 13 May 2018 22:22:10 +0000 (18:22 -0400)]
zynq: copy config to kernel 4.14

The file will be used as a base configuration
for kernel 4.14

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agouboot-zynq: update to 2017.03
Luis Araneda [Sun, 13 May 2018 22:12:21 +0000 (18:12 -0400)]
uboot-zynq: update to 2017.03

Compile-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agozynq: fix detection of the zybo board
Luis Araneda [Sun, 13 May 2018 19:55:00 +0000 (15:55 -0400)]
zynq: fix detection of the zybo board

The board_name was being tested for "xlnx,zynq-zybo",
but the .dts compatible string is "digilent,zynq-zybo"

Also, sorted the boards alphabetically, and added an
error message for unsupported boards

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agozynq: remove hard-coded network configuration
Luis Araneda [Sun, 13 May 2018 18:52:04 +0000 (14:52 -0400)]
zynq: remove hard-coded network configuration

This is no longer necessary since commit 57776e6
(base-files: remove default /etc/config/network,
generate it via board.d instead)

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agozynq: reworked image creation process
Luis Araneda [Sun, 13 May 2018 18:05:38 +0000 (14:05 -0400)]
zynq: reworked image creation process

After commit a1248da (zynq: convert to new image build code),
all boards, became unbootable, entering into a boot loop.

Replace the compressed kernel zImage by an uncompressed Image,
which is compressed after with gzip. Also, enable the creation
of an initramfs image by default.

Change images' filename to match the compatible string from the
respective .dts file (<vendor>_<model>). Also, use the shared
mkits.sh script and remove the target specific one.

Fixes: FS#1204

Run-tested: ZedBoard

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
6 years agobrcm2708: Update brcm2708-gpu-fw package
Christo Nedev [Fri, 1 Jun 2018 14:23:21 +0000 (14:23 +0000)]
brcm2708: Update brcm2708-gpu-fw package

Problem - rapsberry pi 3 b/b+ does not boot with bcm2710 images!

How Raspberry Pi boots Actualy?

When Raspberry is switched on GPU is activated.
1. GPU execute First stage bootloader from ROM.
First stage bootloader mount the FAT boot partition on the SD card
and execute second stage bootloader (bootcode.bin).
2. Second stage bootloader (bootcode.bin) activate SDRAM.
Load the GPU firmware (start.elf).
3. GPU firmware (start.elf)
  a) display Rainbow splash.
  b) read firmware configuration file config.txt and
     split the RAM using fixup.dat.
  c) loads a cmdline.txt
  d) enables the CPU.
  e) loads the kernel image configurable via config.txt

In your target/linux/brcm2708/image/config.txt
 493 ## kernel (string)
 494 ##     Alternative name to use when loading kernel.
 495 ##
 496 #kernel=""
it is not configured!

But in your target/linux/brcm2708/image/Makefile
  75   KERNEL_IMG := kernel8.img
  76   DEVICE_TITLE := Raspberry Pi 3B/3B+
you have kernel8.img

GPU Firmware search order by default for a PI 3 is:
kernel8.img if found boot in 64 bit mode
kernel8-32.img if found boot in 32 bit mode
kernel7.img if found boot in 32 bit mode
kernel.img if found boot in 32 bit mode

But a PI 2 will start the search from kernel7.img and
a PI 1 only looks for kernel.img.

Đžbviously the kernel has been found.
But something goes wrong and the device is restarted.

In your package/kernel/brcm2708-gpu-fw/Makefile
  11 PKG_NAME:=brcm2708-gpu-fw
  12 PKG_VERSION:=2017-08-08
  13 PKG_RELEASE:=e7ba7ab135f5a68b2c00a919ea9ac8d5528a5d5b
boot loader is 10 monts old.

In conclusion, the best way to solve the problem is
to update the boot loader!

Fixup_cd.dat and start_cd.elf files are not necessary.
These are used when GPU memory is set to 16 MB, which disables
some GPU features.
I did not remove them just in case!

cheers

Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
6 years agoramips: fix reboot with W25Q256 with 4-address-mode enabled
Daniel Golle [Wed, 6 Jun 2018 23:51:58 +0000 (01:51 +0200)]
ramips: fix reboot with W25Q256 with 4-address-mode enabled

Some board vendors actually changed the loader to expect the chip
to come up in 4-address-mode and flipped the ADP bit in the flash
chip's configuration register which makes it come up in 4-address-mode.
Hence it doesn't make sense to avoid switching to 4-address-mode on
those boards but the opposite as otherwise reboot hangs eg. on the
WrtNode2 boards. Fix this by checking the ADP register and only using
SPI_NOR_4B_READ_OP on chips which have ADP==0 (come up in 3-byte mode).

See also datasheet section 7.1.11 Power Up Address Mode (ADP)

Fixes: 22d982ea0 ("ramips: add support for switching between 3-byte and 4-byte addressing on w25q256 flash")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agoebtables: update to latest git 2018-06-06
Hans Dedecker [Wed, 6 Jun 2018 20:30:57 +0000 (22:30 +0200)]
ebtables: update to latest git 2018-06-06

5699354 extensions: fix build failure on fc28
e6359ee build: update ebtables.h from kernel and drop local unused copy

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoar71xx: switch CPE/WBS 210/510 to okli-loader
Matthias Schiffer [Tue, 5 Jun 2018 22:35:17 +0000 (00:35 +0200)]
ar71xx: switch CPE/WBS 210/510 to okli-loader

We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.

While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.

Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.

Fixes: e39847ea2f70 ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoath79: lzma-loader: sync with ar71xx target
Matthias Schiffer [Wed, 6 Jun 2018 19:01:32 +0000 (21:01 +0200)]
ath79: lzma-loader: sync with ar71xx target

Import all improvements made in the lzma-loader since development on the
ath79 target started.

This also reverts fe594bf90d09 ("ath79: fix loader-okli, lzma-loader"), as
is obsoleted by 2ad60168b6af ("ar71xx: lzma-loader: move padding workaround
to gzip step").

Likely, many of the changes should be ported to the ramips lzma-loader as
well, but I don't have a device to test this.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoar71xx: make loader-okli build step more generic
Matthias Schiffer [Tue, 5 Jun 2018 22:34:25 +0000 (00:34 +0200)]
ar71xx: make loader-okli build step more generic

Add support for different loader types.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoar71xx: lzma-loader: constify kernel argv array
Matthias Schiffer [Tue, 5 Jun 2018 22:30:57 +0000 (00:30 +0200)]
ar71xx: lzma-loader: constify kernel argv array

By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoar71xx: lzma-loader: set page size to 4KB
Matthias Schiffer [Tue, 5 Jun 2018 22:27:42 +0000 (00:27 +0200)]
ar71xx: lzma-loader: set page size to 4KB

The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agoar71xx: lzma-loader: move padding workaround to gzip step
Matthias Schiffer [Wed, 6 Jun 2018 18:51:05 +0000 (20:51 +0200)]
ar71xx: lzma-loader: move padding workaround to gzip step

Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.

This approach had two issues:

- The padding was only working when .data was non-empty (otherwise the
  section would become NOBITS, omitting it in the binary). .data was only
  empty when no CMDLINE was set, leading to further workarounds like
  fe594bf90d09 ("ath79: fix loader-okli, lzma-loader"), and this
  workaround was only effective because a missing "const" led to the kernel
  argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
  uncompressed .bin and .elf loaders. The prevented embedding the kernel
  cmdline in the loader for non-gz loader types.

To fix both issues, move the creation of the padding from the linker script
to the gzip step.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
6 years agobase-files: fix UCI config parsing and callback handling
Tony Ambardar [Thu, 8 Mar 2018 05:00:45 +0000 (21:00 -0800)]
base-files: fix UCI config parsing and callback handling

There are several long-standing issues present in the UCI shell API as
documented in https://wiki.openwrt.org/doc/devel/config-scripting. They
relate both to high-level, user-defined callback functions used to
process UCI config files, and also to low-level functions used within
scripts generally.

The related problems have been encountered now and in the past, e.g.
https://forum.openwrt.org/viewtopic.php?id=54295, and include:

a) UCI parsing option() function and user-defined option_cb() callbacks
being erroneously called during processing of "list" config file entries;

b) normal usage of the low-level config_set() unexpectedy calling any
defined option_cb() if present; and

c) handling of the list_cb() not respecting the NO_CALLBACK variable.

Root causes include a function stack "inversion", where the low-level
config_set() function incorrectly calls the high-level option() function,
intended only for processing the "option" keyword of UCI config files.

This change addresses the inversion and other issues, making the option
handling code more consistent and smaller, and simplifying developers'
usage of UCI callbacks.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
6 years agokernel: bump 4.14 to 4.14.48
Stijn Tintel [Mon, 4 Jun 2018 17:06:00 +0000 (20:06 +0300)]
kernel: bump 4.14 to 4.14.48

Remove upstreamed patches:
generic/pending/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
generic/pending/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
generic/pending/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
lantiq/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
Update patches that no longer apply:
generic/pending/811-pci_disable_usb_common_quirks.patch
ath79/0009-MIPS-ath79-add-lots-of-missing-registers.patch

Fixes CVE-2018-6412.

Compile-tested: octeon, x86/64.
Runtime-tested: octeon, x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years agoscripts: Replace obsolete POSIX tmpnam in slugimage.pl with File::Temp function
Ted Hess [Tue, 5 Jun 2018 14:05:35 +0000 (10:05 -0400)]
scripts: Replace obsolete POSIX tmpnam in slugimage.pl with File::Temp function

Signed-off-by: Ted Hess <thess@kitschensync.net>
6 years agohostapd: properly build hostapd-only SSL variants
Daniel Golle [Thu, 31 May 2018 13:18:12 +0000 (15:18 +0200)]
hostapd: properly build hostapd-only SSL variants

Make sure hostapd-openssl is actually build against OpenSSL, same
for wolfSSL.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agokernel: modules: package module for Exar 8250 UARTs
Daniel Golle [Tue, 5 Jun 2018 03:35:47 +0000 (05:35 +0200)]
kernel: modules: package module for Exar 8250 UARTs

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agokernel: backport patch to fix dst handling for offloaded connections
Felix Fietkau [Tue, 5 Jun 2018 08:16:49 +0000 (10:16 +0200)]
kernel: backport patch to fix dst handling for offloaded connections

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agohostapd: expose device taxonomy signature via ubus
Felix Fietkau [Mon, 30 Apr 2018 11:48:54 +0000 (13:48 +0200)]
hostapd: expose device taxonomy signature via ubus

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agohostapd: add support for client taxonomy in the full config
Felix Fietkau [Mon, 30 Apr 2018 11:40:42 +0000 (13:40 +0200)]
hostapd: add support for client taxonomy in the full config

This can be used to fingerprint clients to try to identify the exact
model

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agogcc: remove support for version 6.3.0
Felix Fietkau [Sat, 12 May 2018 12:56:36 +0000 (14:56 +0200)]
gcc: remove support for version 6.3.0

It is obsoleted by gcc 7

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomt76: update to the latest version
Felix Fietkau [Sat, 19 May 2018 12:45:54 +0000 (14:45 +0200)]
mt76: update to the latest version

20c0766 mt7603: adjust rx hang watchdog for MT7628
664e321 mt7603: add extra PSE hang check signature for MT7628
f24b56f update MT7628 firmware to the latest version
d87e4b0 mt7603: clear PSE reset bit if PSE reset fails
0ef26ef mt76: only stop tx queues on offchannel, not during the entire scan
f399da3 mt76: prevent tx scheduling during channel change
21c1e1e mt76: move ieee80211_hw allocation to common core
730c292 mt76: wait for pending tx to complete before switching channel
fcbb49e mt76x2: use udelay instead of usleep_range in mt76x2_mac_stop
792dbe0 mt7603: do not hold dev->mutex while flushing dev->mac_work

Signed-off-by: Felix Fietkau <nbd@nbd.name>
6 years agomap: make tunnel encapsulation limit support configurable (FS#1501)
Hans Dedecker [Mon, 4 Jun 2018 15:00:32 +0000 (17:00 +0200)]
map: make tunnel encapsulation limit support configurable (FS#1501)

Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the map-e packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agonetifd: update to latest git HEAD (FS#1501)
Hans Dedecker [Wed, 30 May 2018 20:15:48 +0000 (22:15 +0200)]
netifd: update to latest git HEAD (FS#1501)

a580028 system-linux: make encaplimit configurable for ip6 tunnels (FS#1501)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoodhcp6c: make ds-lite/map tunnel encapsulation limit support configurable (FS#1501)
Hans Dedecker [Tue, 29 May 2018 13:31:21 +0000 (15:31 +0200)]
odhcp6c: make ds-lite/map tunnel encapsulation limit support configurable (FS#1501)

Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501 for dynamic created ds-lite/map
interfaces.
Setting the uci parameter encaplimit_dslite/map to ignore; allows to disable the insertion
of the destination option header for the dynamic created ds-lite/map interface.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit_dslite/map uci parameter accordingly.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agods-lite: make tunnel encapsulation limit support configurable (FS#1501)
Hans Dedecker [Tue, 29 May 2018 13:18:16 +0000 (15:18 +0200)]
ds-lite: make tunnel encapsulation limit support configurable (FS#1501)

Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the ds-lite packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agomvebu: fix broken console on WRT32X (venom)
Michael Gray [Tue, 29 May 2018 09:43:48 +0000 (19:43 +1000)]
mvebu: fix broken console on WRT32X (venom)

The console bootarg is being corrupted on boot, causing various issues
including broken sysupgrade.
Utilising the bootargs mangle patch from other targets, hardcode the console
arguments and fetch the rootfs from the bootloader.

Kernel command line: console=ttyS0,115200 root=/dev/mtdblock8

Bootloader command line (ignored): console= root=/dev/mtdblock8

Please cherry pick to 18.06 too

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
6 years agooxnas: bring in new oxnas target
Daniel Golle [Thu, 31 May 2018 17:41:28 +0000 (19:41 +0200)]
oxnas: bring in new oxnas target

Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.

Functional issues:
 * PCIe won't come up (hence no USB3 on Shuttle KD20)
 * I2C bus of Akitio myCloud device is likely not to work (missing
   debounce support in new pinctrl driver)

Code-style issues:
 * plla/pllb needs further cleanup -- currently their users or writing
   into the syscon regmap after acquireling the clk instead of using
   defined clk_*_*() functions to setup multipliers and dividors.
 * PCIe phy needs its own little driver.
 * SATA driver is a monster and should be split into an mfd having
   a raidctrl regmap, sata controller, sata ports and sata phy.

Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agouboot-oxnas: fix build with newer GCC
Daniel Golle [Fri, 1 Jun 2018 13:25:42 +0000 (15:25 +0200)]
uboot-oxnas: fix build with newer GCC

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agooxnas: kill old oxnas target
Daniel Golle [Thu, 31 May 2018 15:28:38 +0000 (17:28 +0200)]
oxnas: kill old oxnas target

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agonetifd: drop conflicting 'device' interface property
Ivan Shapovalov [Sun, 13 May 2018 21:05:43 +0000 (00:05 +0300)]
netifd: drop conflicting 'device' interface property

Do not set device runtime property on interfaces in the hotplug handler
and in fixup_interfaces(). This property conflicts with device option
in several proto handlers (mainly QMI and other WWAN/3G protos) and does
not seem to be used anywhere.

Signed-off-by: Ivan Shapovalov <intelfx@intelfx.name>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
6 years agokernel: re-add export ipv6_push_frag_opts for tunneling now patch
Hans Dedecker [Fri, 1 Jun 2018 11:37:09 +0000 (13:37 +0200)]
kernel: re-add export ipv6_push_frag_opts for tunneling now patch

The patch got removed by commit 7dca1bae82 (kernel: bump to 4.9.105)
but is still required as ipv6_push_frag_opts needs to be exported.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoRevert "ramips: Move PCI driver to files directory"
John Crispin [Fri, 1 Jun 2018 09:41:13 +0000 (11:41 +0200)]
Revert "ramips: Move PCI driver to files directory"

This reverts commit a098a78a33a6b096d15c9982b5d6457988e09f03.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "ramips: Remove redundant owner assignment"
John Crispin [Fri, 1 Jun 2018 09:41:12 +0000 (11:41 +0200)]
Revert "ramips: Remove redundant owner assignment"

This reverts commit 2ad4daf5794b08878467c1dac5bef7487109e4da.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "ramips: improve interrupt mapping"
John Crispin [Fri, 1 Jun 2018 09:41:11 +0000 (11:41 +0200)]
Revert "ramips: improve interrupt mapping"

This reverts commit 5f7396ebef09b224edf08b0bda113613a42f0928.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "ramips: remove conditional compilation."
John Crispin [Fri, 1 Jun 2018 09:41:11 +0000 (11:41 +0200)]
Revert "ramips: remove conditional compilation."

This reverts commit 1f786257147f978ce4c5750fdc404851453fafcb.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "ramips: remove unnecessary resource details."
John Crispin [Fri, 1 Jun 2018 09:41:10 +0000 (11:41 +0200)]
Revert "ramips: remove unnecessary resource details."

This reverts commit edea934799911c54ffa7024ef9a650f9dfc8c695.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "ramips: pci: sync with staging driver"
John Crispin [Fri, 1 Jun 2018 09:41:08 +0000 (11:41 +0200)]
Revert "ramips: pci: sync with staging driver"

This reverts commit e07baec9faf487fd143976636025b5da55e13c20.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "ramips: Add back some non-mt7621 code that staging removed"
John Crispin [Fri, 1 Jun 2018 09:41:04 +0000 (11:41 +0200)]
Revert "ramips: Add back some non-mt7621 code that staging removed"

This reverts commit 048e41f6496697863cc7d73ab95fa89a6ddf2470.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"
John Crispin [Fri, 1 Jun 2018 09:41:00 +0000 (11:41 +0200)]
Revert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"

This reverts commit 02f815d1907cdd7e042415a2b4a749c819087168.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agonettle: bump to 3.4
Kevin Darbyshire-Bryant [Wed, 30 May 2018 08:46:34 +0000 (08:46 +0000)]
nettle: bump to 3.4

3.4 is mainly a bug fix/maintenance release.

3KB increase in ipk lib size on mips.

Compile tested for: ar71xx, ramips
Run tested on: ar71xx Archer C7 v2, ramips mir3g

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
6 years agomtd: mark as nonshared to fix FS#484
Mirko Parthey [Thu, 31 May 2018 13:24:31 +0000 (15:24 +0200)]
mtd: mark as nonshared to fix FS#484

The mtd tool is built with different configurations depending on the
target. For example, brcm47xx adds the fixtrx subcommand, without which
an image fails when booting the second time.

Mark the mtd package as nonshared to really fix FS#484.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
6 years agokernel: bump to 4.9.105
Kevin Darbyshire-Bryant [Thu, 31 May 2018 19:49:08 +0000 (19:49 +0000)]
kernel: bump to 4.9.105

Refresh patches.

Drop patches that have been upstreamed:
target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
target/linux/generic/backport-4.9/095-v4.12-ipv6-Need-to-export-ipv6_push_frag_opts-for-tunnelin.patch
target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch

Compile & run tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
6 years agoath79: correct wmac names in dts
Alex Maclean [Wed, 30 May 2018 13:21:09 +0000 (14:21 +0100)]
ath79: correct wmac names in dts

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
6 years agoath79: add TP-Link TL-WR703N port
Alex Maclean [Wed, 30 May 2018 13:18:54 +0000 (14:18 +0100)]
ath79: add TP-Link TL-WR703N port

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
6 years agoath79: add TP-Link TL-WR740N/ND v2 port
Alex Maclean [Wed, 30 May 2018 13:18:53 +0000 (14:18 +0100)]
ath79: add TP-Link TL-WR740N/ND v2 port

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
6 years agoath79: add pinmux node to ar724x.dtsi
Alex Maclean [Wed, 30 May 2018 13:18:52 +0000 (14:18 +0100)]
ath79: add pinmux node to ar724x.dtsi

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
6 years agoath79: add AR7240 dtsi
Alex Maclean [Wed, 30 May 2018 13:18:51 +0000 (14:18 +0100)]
ath79: add AR7240 dtsi

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
6 years agoath79: add tiny subtarget
Alex Maclean [Wed, 30 May 2018 13:18:50 +0000 (14:18 +0100)]
ath79: add tiny subtarget

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
6 years agoath10k-ct: Update driver to latest
Koen Vandeputte [Thu, 31 May 2018 08:21:06 +0000 (10:21 +0200)]
ath10k-ct: Update driver to latest

127f98189ee5 ath10k:  Fix bad return w/out unlock, compile w/out debugfs
b8f48f3c138f Fix survey-dump for 4.7, 4.9 and 4.13 kernels.
fa8259ad5d6d ath10k-ct:  Support survey dump in 10.1 firmware.
2853e1337ecf ath10k-ct:  Add 4.16 ath10k-ct driver to package.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
CC: Ben Greear <greearb@candelatech.com>
6 years agoath79: fix glinet ar150 lan/wan ordering
John Crispin [Wed, 30 May 2018 13:18:55 +0000 (15:18 +0200)]
ath79: fix glinet ar150 lan/wan ordering

LAN and WAN were swapped

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoRevert "kernel: backport export ipv6_push_frag_opts for tunneling now"
Daniel Golle [Thu, 31 May 2018 23:37:51 +0000 (01:37 +0200)]
Revert "kernel: backport export ipv6_push_frag_opts for tunneling now"

This reverts commit daa73b63d5dc5eb264341336c0d7cd64d750664d.
The fix has already been imported by
commit b7735d8113 ("kernel: import follow-up fix for previous backport").
The patch won't apply twice.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agokernel: backport export ipv6_push_frag_opts for tunneling now
Hans Dedecker [Thu, 31 May 2018 16:08:19 +0000 (18:08 +0200)]
kernel: backport export ipv6_push_frag_opts for tunneling now

Patch is required on top of commit 6c81c27efa as ipv6_push_frag_opts needs to
be exported for usage in ip6_tunnel.c

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agowireguard: bump to 0.0.20180531 to fix flow offloading
Jason A. Donenfeld [Thu, 31 May 2018 01:05:51 +0000 (03:05 +0200)]
wireguard: bump to 0.0.20180531 to fix flow offloading

This version bump was made upstream mostly for OpenWRT, and should fix
an issue with a null dst when on the flow offloading path.

While we're at it, Kevin and I are the only people actually taking care
of this package, so trim the maintainer list a bit.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
6 years agokernel: import follow-up fix for previous backport
Daniel Golle [Thu, 31 May 2018 00:25:59 +0000 (02:25 +0200)]
kernel: import follow-up fix for previous backport

Buildbots complaining made me wonder what's going on...
ERROR: "ipv6_push_frag_opts" [net/ipv6/ip6_tunnel.ko] undefined!

Fixes: 6c81c27efa ("kernel: backport fix for missing tunnel encapsulation limit option")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agohostapd: update packaging and patches
Daniel Golle [Wed, 30 May 2018 22:10:49 +0000 (00:10 +0200)]
hostapd: update packaging and patches

Clean up conflicts/provides/depends hell and add PROVIDES for
eapol-test variants while at it.
Update mesh-DFS patchset from Peter Oh to v5 (with local fixes) which
allows to drop two revert-patches for upstream commits which previously
were necessary to un-break mesh-DFS support.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agowolfssl: change defaults to cover wpa_supplicant needs
Daniel Golle [Wed, 30 May 2018 22:34:15 +0000 (00:34 +0200)]
wolfssl: change defaults to cover wpa_supplicant needs

Implicetely selecting the required options via Kconfig snippet from
hostapd worked fine in local builds when using menuconfig but confused
the buildbots which (in phase1) may build wpad-mini and hence already
come with CONFIG_WPA_WOLFSSL being defined as unset which then won't
trigger changing the defaults of wolfssl.

Work around by explicitely reflecting wpa_supplicant's needs in
wolfssl's default settings to make buildbots happy.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agotoolchain/glibc: update to latest 2.26 commit
Hans Dedecker [Wed, 30 May 2018 12:38:37 +0000 (14:38 +0200)]
toolchain/glibc: update to latest 2.26 commit

4df8479e6b Add NEWS entry for CVE-2018-11236
a5bc5ec967 Add references to CVE-2018-11236, CVE-2017-18269
58ad5f8a64 Add a test case for [BZ #23196]
6b4362f2cb Don't write beyond destination in __mempcpy_avx512_no_vzeroupper (bug 23196)

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agokernel: backport fix for missing tunnel encapsulation limit option
Hans Dedecker [Wed, 30 May 2018 09:41:14 +0000 (11:41 +0200)]
kernel: backport fix for missing tunnel encapsulation limit option

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agocurl: Add ca-bundle dependency
Rosen Penev [Sun, 27 May 2018 22:13:48 +0000 (15:13 -0700)]
curl: Add ca-bundle dependency

While building, curl complains that the path specified is missing.
Also, without ca-bundle, something like 'curl https://www.google.com'
does not work due to a certificate verify error.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agocurl: Use ca-bundle for all TLS libraries.
Rosen Penev [Sun, 27 May 2018 22:13:47 +0000 (15:13 -0700)]
curl: Use ca-bundle for all TLS libraries.

It simplifies the Makefile a bit. In addition, using ca-bundle
saves some space as well.

It also fixes an issue with at least transmission, which has a dependency
on ca-bundle, but currently libcurl with OpenSSL or GnuTLS cause it not
to work.

This has been tested on mt7621 with OpenSSL and GnuTLS just by running
'curl https://www.google.com' and seeing if there's a verify error.
The rest are already using ca-bundle and therefore work fine.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
6 years agoramips: Use generic board detect for GnuBee devices
Rosen Penev [Sun, 27 May 2018 00:26:14 +0000 (17:26 -0700)]
ramips: Use generic board detect for GnuBee devices

This is a port of an old commit from mkresin's tree:

09260cdf3e9332978c2a474a58e93a6f2b55f4a8

This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agoramips: Fix a few other GnuBee DTS differences
Rosen Penev [Sun, 27 May 2018 22:50:50 +0000 (15:50 -0700)]
ramips: Fix a few other GnuBee DTS differences

I was carrying a local commit that added the sdhci stuff and missed it
as a result.

Also fix the rgmii3 thing in the PC2 DTS file as that's bogus and causes
a dmesg warning that it's bogus.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agoramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928
Rosen Penev [Tue, 29 May 2018 18:03:03 +0000 (11:03 -0700)]
ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928

That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.

eg. 2.4GHz working but not 5GHz.

As all of these dts entries are already specified in mt7621.dtsi, remove
them.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agoath10k-firmware: Fix two more typos
Rosen Penev [Tue, 29 May 2018 18:03:02 +0000 (11:03 -0700)]
ath10k-firmware: Fix two more typos

Actually tested with a local build instead of with scp'ing the firmware.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agokernel: bump 4.14 to 4.14.44
Stijn Tintel [Mon, 28 May 2018 21:10:44 +0000 (00:10 +0300)]
kernel: bump 4.14 to 4.14.44

Refresh patches.

Remove upstreamed patch:
generic/pending/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
Update patches that no longer applies:
generic/hack/901-debloat_sock_diag.patch

Compile-tested on: x86/64.
Runtime-tested on: x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years agomac80211: rt2x00: no longer use TXOP_BACKOFF for probe frames
Daniel Golle [Mon, 28 May 2018 13:45:43 +0000 (15:45 +0200)]
mac80211: rt2x00: no longer use TXOP_BACKOFF for probe frames

Import a revert-commit from Stanislaw Gruszka which significantly
improves WiFi performance on rt2x00 based hardware.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agomediatek: add missing symbols for mt7622
John Crispin [Mon, 28 May 2018 06:12:28 +0000 (08:12 +0200)]
mediatek: add missing symbols for mt7622

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoath10k-firmware: Fix typo in last commit
Rosen Penev [Sun, 27 May 2018 16:21:40 +0000 (09:21 -0700)]
ath10k-firmware: Fix typo in last commit

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agokernel: add missing softdog symbol
John Crispin [Sun, 27 May 2018 07:22:40 +0000 (09:22 +0200)]
kernel: add missing softdog symbol

Signed-off-by: John Crispin <john@phrozen.org>
6 years agomediatek: add missing symbols
John Crispin [Sun, 27 May 2018 07:22:21 +0000 (09:22 +0200)]
mediatek: add missing symbols

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoar71xx: add support for GL.iNet GL-AR750S
Luo chongjun [Fri, 25 May 2018 10:06:37 +0000 (18:06 +0800)]
ar71xx: add support for GL.iNet GL-AR750S

This patch adds supports for GL-AR750S.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
6 years agoath10k-firmware: Fix QCA6174 support
Rosen Penev [Fri, 25 May 2018 03:47:46 +0000 (20:47 -0700)]
ath10k-firmware: Fix QCA6174 support

Currently when installing the firmware, a bunch of files and directories
that the ath10k driver does not look for are created.

The package now installs firmware for both hw 2.1 and 3.0 devices.
2.1 is abandonware but may be useful to keep.

3.0 firmware was tested on a Killer 1535 to be relatively stable with
802.11w disabled. 802.11w causes multiple firmware crashes but that's true
of other ath10k firmwares as well.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
6 years agowolfssl: add PKG_CONFIG_DEPENDS symbols
Daniel Golle [Fri, 25 May 2018 18:35:46 +0000 (20:35 +0200)]
wolfssl: add PKG_CONFIG_DEPENDS symbols

This change will trigger rebuild on buildbots in case of changed config
symbols, like in the case of hostapd selecting some wolfssl symbols
lately.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agohostapd: convert ssl provider build options to variants
Daniel Golle [Fri, 25 May 2018 13:59:41 +0000 (15:59 +0200)]
hostapd: convert ssl provider build options to variants

Instead of selecting the SSL provider at compile time, build package
variants for each option so users can select the binary package without
having to build it themselves.
Most likely not all variants have actually ever been user by anyone.
We should reduce the selection to the reasonable and most used
combinations at some point in future. For now, build them all.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agofirewall: update to latest git HEAD
Hans Dedecker [Fri, 25 May 2018 12:29:58 +0000 (14:29 +0200)]
firewall: update to latest git HEAD

30463d0 zones: add interface/subnet bound LOG rules
0e77bf2 options: treat time strings as UTC times

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agofstools: update to latest git HEAD
Hans Dedecker [Fri, 25 May 2018 07:45:04 +0000 (09:45 +0200)]
fstools: update to latest git HEAD

dd02dad fstools: allow the mounting with full access time accounting
242248c fstools: allow to compress the filesystem

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoar71xx: fix bad "proto" references in default network configuration
Jo-Philipp Wich [Fri, 25 May 2018 07:44:28 +0000 (09:44 +0200)]
ar71xx: fix bad "proto" references in default network configuration

This change was originally meant to go along with the ucidef_set_interface()
fixup.

Fixes: 7e664b7c2d ("base-files: fix ucidef_set_interface() protocol selection")
Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agobase-files: fix ucidef_set_interface() protocol selection
Jo-Philipp Wich [Fri, 25 May 2018 05:28:28 +0000 (07:28 +0200)]
base-files: fix ucidef_set_interface() protocol selection

The previous refactoring of ucidef_set_interface() removed the protocol
selection heuristic which breaks the networking defaults for the majority
of boards.

Re-add the protocol selection and rename two bad "proto" references to
the expected "protocol" value.

Fixes: 85048a9c1f ("base-files: rework _ucidef_set_interface to be more generic")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agohostapd: update to git HEAD of 2018-05-21, allow build against wolfssl
Daniel Golle [Sat, 28 Apr 2018 19:12:19 +0000 (21:12 +0200)]
hostapd: update to git HEAD of 2018-05-21, allow build against wolfssl

Support for building wpa_supplicant/hostapd against wolfssl has been
added upstream recently, add build option to allow users using it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>