Alexander Graf [Thu, 25 Jan 2018 11:05:56 +0000 (12:05 +0100)]
bcm2835_pinctrl: Probe pre-reloc
The serial drivers now depend on the pinctrl driver to determine whether
they are enabled. That means if a serial device wants to be used pre-reloc,
we also need the pinctrl device pre-reloc.
Adapt the pinctrl driver as well as dts overlay accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:55 +0000 (12:05 +0100)]
bcm2835_pl011_serial: Add BCM2835 specific serial driver
On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve this
for the pl011 device, add a bcm2835 specific pl011 wrapper device
that does this check but otherwise behaves like a pl011 device.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:54 +0000 (12:05 +0100)]
MAINTAINERS: Take over BCM2835 maintainership
It seems as if I have more interest in BCM2835 support than most others,
so I'll bite the bullet and declare myself maintainer. It'd be a shame
to leave that platform orphaned.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:53 +0000 (12:05 +0100)]
bcm2835_mu_serial: Convert to Kconfig
Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:52 +0000 (12:05 +0100)]
pl01x: Convert CONFIG_PL01X_SERIAL to Kconfig
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl01x.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:51 +0000 (12:05 +0100)]
pl011: Convert CONFIG_PL011_SERIAL to Kconfig
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl011.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:50 +0000 (12:05 +0100)]
pl010: Convert CONFIG_PL010_SERIAL to Kconfig
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl010.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:49 +0000 (12:05 +0100)]
pl01x: Convert to dev_read
The fdtdec API is deprecated, convert the pl010 and pl011 devices to
use the dev_read API instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:48 +0000 (12:05 +0100)]
serial_bcm283x_mu: Fail loading if not muxed
The bcm283x mini-uart is only really usable as U-Boot serial output
when it is muxed to the UART pins of the RPi pin header.
So fail probing in case it is not muxed correctly, as in that case
firmware did not initialize it properly either.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:47 +0000 (12:05 +0100)]
serial_bcm283x_mu: Always skip init
The serial initialization doesn't always quite work for me, so let's
always skip it for now. We know that firmware on the RPi initializes
us properly already.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:46 +0000 (12:05 +0100)]
serial_bcm283x_mu: Convert to dev_read
The fdtdec API got deprecated in favor of dev_read calls.
Use those instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:45 +0000 (12:05 +0100)]
rpi: Determine PL011/Mini-UART availability at runtime
Firmware on the Raspberry Pi family of devices can dynamically configure either
the PL011, Mini-UART or no device at all to be routed to the user accessible
UART pins.
That means we need to always include both drivers, because we can never be sure
which of the two serial devices firmware actually chooses to use.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:44 +0000 (12:05 +0100)]
serial: bcm283x_mu: Remove support for post-init disabling
We are switching to a model where a serial device doesn't even get probed when
it's not muxed properly, so we don't need device specific disabling
functionality anymore.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:43 +0000 (12:05 +0100)]
rpi: Remove runtime disabling support for serial
We are switching to a model where our board file can directly fail probing
of serial devices when they're not usable, so remove the current runtime
hack we have.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Thu, 25 Jan 2018 11:05:42 +0000 (12:05 +0100)]
serial: Use next serial device if probing fails
Currently our serial device search chokes on the fact that the serial
probe function could fail. If it does, instead of searching for the next
usable serial device, it just quits.
This patch changes the fallback logic so that even when a serial device
was not probed correctly, we just try the next ones until we find one that
works.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Faiz Abbas [Wed, 24 Jan 2018 09:14:49 +0000 (14:44 +0530)]
am33xx: board: Call spl_early_init() to support sdram_init()
With driver model enabled in SPL, sdram_init() requires device tree
and malloc to be initialized.
Therefore call spl_early_init() in early_system_init().
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Felix Brack [Tue, 23 Jan 2018 17:27:22 +0000 (18:27 +0100)]
arm: add support for PDU001
This patch adds support for the PDU001 board.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
Alexander Graf [Tue, 23 Jan 2018 17:05:22 +0000 (18:05 +0100)]
mmc: Add bcm2835 sdhost controller
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Tue, 23 Jan 2018 17:05:21 +0000 (18:05 +0100)]
bcm283x: Add pinctrl driver
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tuomas Tynkkynen [Sun, 21 Jan 2018 16:16:42 +0000 (18:16 +0200)]
powerpc: Drop CONFIG_WALNUT and other related dead code
CONFIG_WALNUT was dropped in June 2017 in:
commit
98f705c9cefdfd ("powerpc: remove 4xx support")
While at it, the related CONFIG_MACH_SPECIFIC and the have_of
and _machine variables are unused as well, so drop them too.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Masahiro Yamada [Sun, 21 Jan 2018 10:19:18 +0000 (19:19 +0900)]
libfdt: migrate include/libfdt_env.h to a wrapper
libfdt_env.h is supposed to provide system-dependent defines.
scripts/dtc/libfdt/libfdt_env.h from upstream DTC is suitable
for user-space, so we should use this for USE_HOSTCC case.
For compiling U-Boot, we need to override such system-dependent
defines, so use <linux/libfdt_env.h> imported from Linux.
<libfdt.h> selects a proper one. Maybe, we should split header
inclusion completely, but I do not want too many patches at one.
I can rip off the include/libfdt_env.h from HOST_EXTRACFLAGS.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Sun, 21 Jan 2018 10:19:17 +0000 (19:19 +0900)]
libfdt: migrate libfdt.h to a wrapper + U-Boot own code
There is tons of code duplication between lib/libfdt/libfdt.h and
scripts/dtc/libfdt/libfdt.h. Evacuate the U-Boot own code to
include/libfdt.h and remove lib/libfdt/libfdt.h.
For host tools, <libfdt.h> should include scripts/dtc/libfdt/libfdt.h,
which is already suitable for user-space.
For compiling U-Boot, <linux/libfdt.h> should be included because we
need a different libfdt_env.h .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Sun, 21 Jan 2018 10:19:16 +0000 (19:19 +0900)]
libfdt: move working_fdt and FDT_RAMDISK_OVERHEAD to include/libfdt.h
libfdt_env.h exists to contain system-dependent defines:
- typedef of fdt*_t
- fdt*_to_cpu(), cpu_to_fdt*
working_fdt and FDT_RAMDISK_OVERHEAD are unrelated to the environment,
so they must get out of this header.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Sun, 21 Jan 2018 10:19:15 +0000 (19:19 +0900)]
tools: include necessary headers explicitly
Several host-tools use "bool" type without including <stdbool.h>.
This relies on the crappy header inclusion chain.
tools/Makefile has the following line:
HOST_EXTRACFLAGS += -include $(srctree)/include/libfdt_env.h \
All host-tools are forced to include libfdt_env.h even if they are
totally unrelated to FDT. Then, <stdbool.h> is indirectly included
as follows:
include/libfdt_env.h
-> include/linux/types.h
-> <stdbool.h>
I am fixing this horrible crap. In advance, I need to add necessary
include directives explicitly. tools/fdtgrep.c needs more; <fctl.h>
for open() and <errno.h> for errno.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Sun, 21 Jan 2018 10:19:14 +0000 (19:19 +0900)]
libfdt: fix <linux/libfdt.h>
I do not remember why, but this is apparently a file-copy mistake.
The file name is libfdt.h, but its content is that of libfdt_env.h
Re-import it from upstream Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Sun, 21 Jan 2018 10:19:13 +0000 (19:19 +0900)]
libfdt: migrate fdt_rw.c to a wrapper of scripts/dtc/libfdt/fdt_rw.c
The only difference between scripts/dtc/libfdt/fdt_rw.c and
lib/libfdt/fdt_rw.c is fdt_remove_unused_strings().
It is only used by fdtgrep, so we do not need to compile it for U-Boot
image. Move it to tools/libfdt/fdw_rw.c so that lib/libfdt/fdt_rw.c
can be a wrapper of scripts/dtc/libfdt/fdt_rw.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Sun, 21 Jan 2018 09:34:57 +0000 (18:34 +0900)]
host-tools: use python2 explicitly for shebang
All of these host tools are apparently written for Python2,
not Python3.
Use 'python2' in the shebang line according to PEP 394
(https://www.python.org/dev/peps/pep-0394/).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Derald D. Woods [Sun, 21 Jan 2018 03:16:14 +0000 (21:16 -0600)]
ARM: omap3: evm: Fix distro bootcmd UBIFS and MMC support
The omap3_evm board does not boot when commit:
a47ca2cf67 ("ARM: omap3: evm: Add kernel image loading from UBIFS and EXT4")
is applied after commit:
3dde8f2037 ("Merge git://git.denx.de/u-boot-mmc")
This commit reduces the CONFIG_EXTRA_ENV_SETTINGS size and better
leverages the existing distro bootcmd infrastructure.
- Use updated UBIFS support from config_distro_bootcmd.h
- Use LEGACY_MMC naming found in am335x_evm.h and ti_omap4_common.h
- Remove extra environment content that is no longer needed
[MMC(0:1)/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-evm-mmc-fat
label omap3-evm-mmc-fat
kernel /zImage
fdt /omap3-evm.dtb
append console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
[MMC(0:2)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-evm-mmc-ext4
label omap3-evm-mmc-ext4
kernel /boot/zImage
fdt /boot/omap3-evm.dtb
append console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
[NAND(ubi0:rootfs)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-evm-nand-ubifs
label omap3-evm-nand-ubifs
kernel /boot/zImage
fdt /boot/omap3-evm.dtb
append console=ttyO0,115200n8 root=ubi0:rootfs rw ubi.mtd=rootfs noinitrd rootfstype=ubifs rootwait
---8<-------------------------------------------------------------------
Fixes:
a47ca2cf67 ("ARM: omap3: evm: Add kernel image loading from UBIFS and EXT4")
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Derald D. Woods [Sun, 21 Jan 2018 03:16:13 +0000 (21:16 -0600)]
distro bootcmd: Allow board defined UBI partition and volume names
This commit allows overriding the default assumption that the boot UBI
MTD partition is named 'UBI' and the UBI volume is 'boot'. A board
desiring to use a legacy or alternative NAND layout can now define the
following two extra environment variables:
bootubipart=<some_ubi_partition_name>
bootubivol=<some_ubi_volume_name>
EXAMPLE:
[include/configs/some_board.h]
---8<-------------------------------------------------------------------
[...]
#include <config_distro_defaults.h>
#define MEM_LAYOUT_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV
#define BOOT_TARGET_DEVICES(func) \
func(UBIFS, ubifs, 0)
#include <config_distro_bootcmd.h>
[...]
#define CONFIG_EXTRA_ENV_SETTINGS \
MEM_LAYOUT_ENV_SETTINGS \
"bootubivol=rootfs\0" \
"bootubipart=rootfs\0" \
BOOTENV
[...]
---8<-------------------------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Kever Yang [Sat, 20 Jan 2018 10:00:26 +0000 (18:00 +0800)]
spl: use different BOARD_INIT MACRO for spl and tpl
SPL and TPL may not always need spl_board_init() at the same time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Alberto Sánchez Molero [Sat, 20 Jan 2018 07:17:57 +0000 (09:17 +0200)]
fs: btrfs: Fix unaligned memory accesses
Loading files stored with lzo compression from a btrfs filesystem was
producing unaligned memory accesses, which were causing a data abort
and a reset on an Orange Pi Zero.
The change in hash.c is not triggered by any error but follows the
same pattern. Please confirm.
Fixed according to doc/README.unaligned-memory-access.txt
Signed-off-by: Alberto Sánchez Molero <alsamolero@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Kever Yang [Wed, 17 Jan 2018 03:05:38 +0000 (11:05 +0800)]
spl: atf: pass NULL for bl32_ep pc
ATF use bl32_ep_info->pc to decide if thre is an available bl32,
let's mark it as NULL first.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Eddie Cai [Wed, 17 Jan 2018 01:51:41 +0000 (09:51 +0800)]
rockchip: rk3036: enable rockusb support on rk3036 based device
Rockchip Rockusb driver already merged. So we enable rockusb
support on rk3036 based device.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 16 Jan 2018 08:08:18 +0000 (16:08 +0800)]
rockchip: dts: rk3128: update pwm-cell for pwm0
The backlight pwm-cell is 3.
This remove the warning in buildman:
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Property 'pwms', cell 3 is not a phandle reference in /backlight
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Missing property '#pwm-cells' in node /sram@
10080400 or bad phandle (referred from /backlight:pwms[3])
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Thu, 25 Jan 2018 14:27:10 +0000 (15:27 +0100)]
rockchip: clk: guard set_parent implementations against OF_PLATDATA
The set_parent implementations do not make sense when OF_PLATDATA is
enabled. We guard these against OF_PLATDATA and don't populate the
set_parent-op when this is the case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:07:04 +0000 (14:07 +0800)]
clk: rockchip: clk_rk3368: Implement "assign-clock-parent"
Implement the setting parent for gmac clock, and add internal
pll div set for mac clk.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:06:33 +0000 (14:06 +0800)]
clk: rockchip: clk_rk3288: Implement "assign-clock-parent" and "assign-clock-rate"
The RK3288 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3288 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
implement the gmac clock set parent, but simply ignore the
others' set_rate() operation and return 0 to signal success.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:06:16 +0000 (14:06 +0800)]
ARM: dts: rk3288: Remove unused LCDC clock assigned
The LCDC assigned rate is 0, it will make boot error,
error log:"pll_para_config: the frequency can not be
0 Hz". Remove them, and the lcdc driver will do the
correct clock rate setting.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:51 +0000 (14:05 +0800)]
config: evb-rk3229: Enable rk gmac configs
Add gmac config support for rk3229 evb.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:30 +0000 (14:05 +0800)]
net: gmac_rockchip: Add support for the RK3228 GMAC
The GMAC in the RK3228 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:05:12 +0000 (14:05 +0800)]
clk: rockchip: Add rk322x gamc clock support
Assuming mac_clk is fed by an external clock, set clk_rmii_src
clock select control register from IO for rgmii interface.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:51 +0000 (14:04 +0800)]
rockchip: pinctrl: Add rk322x gmac pinctrl support
Set gmac pins iomux and rgmii tx pins to 12ma drive-strength,
clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:26 +0000 (14:04 +0800)]
rockchip: pinctrl: rk322x: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk322x.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
After that, define the uart2 iomux at rk322x-board file.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:04:11 +0000 (14:04 +0800)]
rockchip: dts: rk3328-evb: Enable gmac2io for rk3328-evb
Add rk3328-evb gmac support.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:56 +0000 (14:03 +0800)]
rockchip: dts: rk3328: Add gmac2io support
Add basic dts configuration for rk3328 gmac2io.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:23 +0000 (14:03 +0800)]
rockchip: configs: Enable GMAC configs for evb-rk3328
Enable GMAC configs for evb-rk3328
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:03:04 +0000 (14:03 +0800)]
net: gmac_rockchip: Add rk3328 gmac support
The GMAC2IO in the RK3328 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3328-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:02:36 +0000 (14:02 +0800)]
clk: rockchip: Add rk3328 gamc clock support
The rk3328 soc has two gmac controllers, one is gmac2io,
the other is gmac2phy. We use the gmac2io rgmii interface
for 1000M phy here.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:02:07 +0000 (14:02 +0800)]
rockchip: pinctrl: Add rk3328 gmac pinctrl support
Need to set gmac m1 pins iomux, gmac m0 tx pins, select bit2
and bit10 at com iomux register. After that, set rgmii m1 tx
pins to 12ma drive-strength, and clean others to 2ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:01:45 +0000 (14:01 +0800)]
rockchip: pinctrl: rk3328: Move the iomux definitions into pinctrl-driver
Clean the iomux definitions at grf_rk3328.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 06:01:12 +0000 (14:01 +0800)]
net: gmac_rockchip: Add support for the RV1108 GMAC
The rv1108 GMAC only support rmii interface, so need to add the
set_rmii() ops. Use the phy current interface to set rmii or
rgmii ops. At the same time, need to set the mac clock rate of
rmii with 50M, the clock rate of rgmii with 125M.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:57 +0000 (13:53 +0800)]
rockchip: pinctrl: rv1108: Move the iomux definitions into pinctrl-driver
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the
conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h,
and move them into pinctrl-driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:56 +0000 (13:53 +0800)]
rockchip: grf_rv1108.h: Fix the grf offsets
The last 4 grf registers offset of rv1108 are wrong, fix them
for correct usage.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:55 +0000 (13:53 +0800)]
rockchip: configs: Enable CONFIG_NET_RANDOM_ETHADDR for rk3288-evb
If the Ethernet address is not set, the network can't work,
enable the random address config for default use.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
David Wu [Sat, 13 Jan 2018 05:53:54 +0000 (13:53 +0800)]
rockchip: dts: rk3399-evb: Change the tx/rx delay value for transmission quality
Give the mac controller the correct tx-delay and rx-delay value
for the rgmii mode transmission. If they are not matched, there
would be Ethernet packets lost, the net feature may not work.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 8 Jan 2018 13:00:27 +0000 (14:00 +0100)]
rockchip: clk: rk3399: accept all assigned-clocks from the 'cru'-node
The RK3399 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3399 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
simply ignore the set_rate() operation and return 0 to signal success.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Philipp Tomsich [Mon, 8 Jan 2018 12:59:18 +0000 (13:59 +0100)]
clk: implement clk_set_defaults()
Linux uses the properties 'assigned-clocks', 'assigned-clock-parents'
and 'assigned-clock-rates' to configure the clock subsystem for use
with various peripheral nodes.
This implements clk_set_defaults() and hooks it up with the general
device probibin in drivers/core/device.c: when a new device is probed,
clk_set_defaults() will be called for it and will process the
properties mentioned above.
Note that this functionality is designed to fail gracefully (i.e. if a
clock-driver does not implement set_parent(), we simply accept this
and ignore the error) as not to break existing board-support.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Series-version: 2
Cover-letter:
clk: support assigned-clock, assigned-clock-parents, assigned-clock-rates
For various peripherals on Rockchip SoCs (e.g. for the Ethernet GMAC),
the parent-clock needs to be set via the DTS. This adds the required
plumbing and implements the GMAC case for the RK3399.
END
Philipp Tomsich [Mon, 8 Jan 2018 12:11:01 +0000 (13:11 +0100)]
rockchip: clk: rk3399: implement set_parent() operation
This implements the (newly added) set_parent() operation for the
RK3399 with a focus on allowing the RGMII clock parent to be
configured via the assigned-clock-parents property of the GMAC node.
This implementation supports only the GMAC (in fact only the RGMII
clock parent) and allows to set this clock's parent either to the
internal SCLK_GMAC or to an external clock input (identifiable by it
providing a 'clock-output-name' of "gmac_clkin").
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Philipp Tomsich [Mon, 8 Jan 2018 10:18:18 +0000 (11:18 +0100)]
clk: refactor clk_get_by_index() into clk_get_by_indexed_prop()
The logic in clk_get_by_index() may be useful for other properties
than 'clocks': e.g. 'assigned-clocks' and 'assigned-clock-parents'
follows the same model.
This commit refactors clk_get_by_index() by introducing an internal
function clk_get_by_indexed_prop() that allows to specify the name
of the property to process. The original clk_get_by_index() call
is simply directed through this helper function with the property
name fixed to "clocks".
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Philipp Tomsich [Mon, 8 Jan 2018 10:15:08 +0000 (11:15 +0100)]
clk: add clk_set_parent()
Clocks may support multiple parents: this change introduces an
optional operation on the clk-uclass to set a clock's parent.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Patrice Chotard [Fri, 19 Jan 2018 17:02:40 +0000 (18:02 +0100)]
clk: clk_stm32f: Fix PLLSAICFGR_PLLSAIP_4 divider value
PLLSAIP divider uses 2 bits (bits 16 and 17) into RCC_PLLSAICFGR
register, available combination are :
00: PLLSAIP = 2
01: PLLSAIP = 4
10: PLLSAIP = 6
11: PLLSAIP = 8
Previously, the divider value was incorrectly set to 6.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Faiz Abbas [Fri, 19 Jan 2018 10:02:48 +0000 (15:32 +0530)]
ARM: AM43XX: Call hw_data_init() again after relocation to update *ctrl
hw_data_init() is called before relocation to initialise hardware data.
Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in
arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be
updated during relocation and will hold a stale value.
Therefore call hw_data_init() again after relocation to
reinitialize *ctrl.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Fri, 19 Jan 2018 10:02:47 +0000 (15:32 +0530)]
configs: Replace CONFIG_ISW_ENTRY_ADDR with CONFIG_SYS_TEXT_BASE
Since
7e0ed13 ("Convert ARCH_OMAP2PLUS boards' CONFIG_SYS_TEXT_BASE to
Kconfig"), a default SYS_TEXT_BASE was set for all ARCH_OMAP2PLUS devices.
CONFIG_ISW_ENTRY_ADDR is used to set SYS_TEXT_BASE in qspi boot.
Simplify this by directly assigning SYS_TEXT_BASE in the defconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Jelle van der Waa [Thu, 18 Jan 2018 19:19:43 +0000 (20:19 +0100)]
tools: remove unused ret
Remove unused ret from fw_env_flush.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patrice Chotard [Thu, 18 Jan 2018 13:10:05 +0000 (14:10 +0100)]
clk: clk_stm32f: Move SYSCFG clock setup into configure_clocks()
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 18 Jan 2018 13:10:04 +0000 (14:10 +0100)]
clk: clk_stm32f: Remove STMMAC clock setup
Thanks to 'commit
ba1f96672522 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Patrice Chotard [Thu, 18 Jan 2018 13:10:03 +0000 (14:10 +0100)]
ARM: dts: stm32: Add STMMAC clocks for stm32f746
Add ETHMAC, ETHMACRX and ETHMACTX clocks for STMMAC.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Bradley Bolen [Sat, 27 Jan 2018 03:11:04 +0000 (22:11 -0500)]
atomic-long: Fix warnings on arm64
Several inline functions in this file reference undefined functions in
U-Boot. For example:
atomic-long.h:73:9: warning: implicit declaration of function
'atomic64_sub_and_test'
atomic-long.h:80:9: warning: implicit declaration of function
'atomic64_dec_and_test'
atomic-long.h:87:9: warning: implicit declaration of function
'atomic64_inc_and_test'
Handle this the same as the 32 bit build by wrapping these functions in
a __UBOOT__ check.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Patrice Chotard [Thu, 18 Jan 2018 12:39:34 +0000 (13:39 +0100)]
ARM: dts: stm32: add stm32429-eval-u-boot dts file
_ Add gpio compatible and aliases for stm32f469
_ Add FMC sdram node
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 18 Jan 2018 12:39:33 +0000 (13:39 +0100)]
ARM: dts: stm32: Add STM32F429 Evaluation board support
This DT file comes from kernel v4.15, this board offers :
_ STM32F429NIH6 microcontroller
_ 4.3” color TFT LCD with resistive touchscreen (480 x 272 pixels)
_ Six 5 V power supply options:
Power jack
ST-LINK/V2 USB connector
User USB HS connector
User USB FS1 connector
User USB FS2 connector
Daughterboard
_ SAI Audio DAC, stereo audio jack which supports headset with
microphone
_ Stereo digital microphone, audio terminal connector used to connect
external speakers
_ 2 GBytes (or more) SDIO interface MicroSD card
_ RF EEPROM on I2 C compatible serial interface
_ RS-232 communication
_ IrDA transceiver
_ JTAG/SWD and ETM trace debug support, ST-LINK/V2 embedded
_ IEEE-802.3-2002 compliant Ethernet connector
_ Camera module
_ 8M x 32-bit SDRAM, 1M x 16-bit SRAM and 8M x 16-bit NOR Flash
_ Joystick with 4-directional control and selector
_ Reset, Wakeup and Tamper buttons
_ 4 color user LEDs
_ Extension connectors & memory connectors for daughterboard or
wrapping board
_ USB OTG HS and FS with Micro-AB connectors
_ RTC with backup battery
_ CAN2.0A/B compliant connection
_ Potentiometer
_ Motor control connector
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 18 Jan 2018 12:39:32 +0000 (13:39 +0100)]
board: stm32: Add stm32f429-evaluation board support
Add stm32f429-evaluation board support.
For more information, please visit:
http://www.st.com/en/evaluation-tools/stm32429i-eval.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 18 Jan 2018 12:39:31 +0000 (13:39 +0100)]
configs: stm32f: Remove STM32_HSE_HZ for all STM32F series
As clk_stm32f driver is able to retrieve HSE frequency from DT,
CONFIG_STM32_HSE_HZ becomes useless.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 18 Jan 2018 12:39:30 +0000 (13:39 +0100)]
clk: stm32: retrieve external oscillator frequency from DT
All current STM32F4 supported boards uses a 8MHz external oscillator.
All current STM32F7 supported boards uses a 25MHz external oscillator.
In order to introduce the new stm32f429-evaluation board which uses a
25MHz external oscillator without creating a dedicated struct
stm32_clk_info for this board, retrieve the external oscillator
frequency from DT and set pll_m accordingly to obtain 1MHz for the VCO.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 18 Jan 2018 12:39:29 +0000 (13:39 +0100)]
ARM: dts: stm32: add "u-boot, dm-pre-reloc" for clk_hse in stm32f7-u-boot
In order to retrieve the clk_hse fixed clock phandle in clk_stm32f driver,
add "u-boot,dm-pre-reloc" property in Uboot specific DT file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Heiko Schocher [Wed, 17 Jan 2018 06:00:37 +0000 (07:00 +0100)]
arm: bootm-fdt.c: fix compiler warning
compiling U-Boot with bosch_mpcxxxxd_sd_defconfig
drops warning:
arch/arm/lib/bootm-fdt.c: In function ‘arch_fixup_fdt’:
arch/arm/lib/bootm-fdt.c:37:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret = 0;
^~~
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Andrew F. Davis [Tue, 16 Jan 2018 20:25:48 +0000 (14:25 -0600)]
arm: mach-omap2: Pass args to secure ROM in SRAM in SPL
When in early SPL we make some secure ROM calls that can effect
DRAM, due to this it is more stable to store the args for these
calls in SRAM, but uninitialized and zero'd globals are placed
in BSS, located in DRAM. Force our args into the data section
which is in SRAM during SPL.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Mario Six [Mon, 15 Jan 2018 10:10:30 +0000 (11:10 +0100)]
common: board_r: Fix style violations
Fix some style violations in the board_r file.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:10:02 +0000 (11:10 +0100)]
common: board_f: Fix style violations
Fix some style violations in the board_f file.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:09:49 +0000 (11:09 +0100)]
serial: ns16550: Fix style violation
Clarify the computation precedence in two ternary operator
constructions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:09:36 +0000 (11:09 +0100)]
include: dm: Fix 'devioe'/'devuce' typos
There are some typos in the documentation of some functions in read.h;
fix those.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mario Six [Mon, 15 Jan 2018 10:07:50 +0000 (11:07 +0100)]
gpio: mpc8xxx: Make live-tree compatible
Make the MPC8xxx GPIO driver compatible with a live device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:07:49 +0000 (11:07 +0100)]
gpio: mpc8xxx: Make compatible with more SoCs
Finally, make the mpc8xxx driver capable of handling more GPIO devices;
this entails adding a special case for the MPC5121 SoC, and adding a set
of new compatible strings.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:07:48 +0000 (11:07 +0100)]
gpio: mpc8xxx: Rename Kconfig option, structures, and functions
Rename the Kconfig option, structures (and their members), as well as
functions of the mpc85xx driver to include mpc8xxx to reflect the more
generic usage.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:07:47 +0000 (11:07 +0100)]
gpio: mpc85xx: Rename driver file to mpc8xxx
In preparation to making the MPC85xx GPIO driver useable for a broader
range of SoCs, rename the driver file.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:07:46 +0000 (11:07 +0100)]
gpio: mpc85xx_gpio: Fix style violations
Fix some style violations in the MPC85XX GPIO driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:07:45 +0000 (11:07 +0100)]
gpio: pca953x_gpio: Make live-tree compatible
Make the pca953x_gpio driver compatible with a live device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Mario Six [Mon, 15 Jan 2018 10:07:44 +0000 (11:07 +0100)]
gpio: pca953x_gpio: Fix style violations
Fix some style violations in the pca953x_gpio driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Martin Etnestad [Fri, 12 Jan 2018 08:04:38 +0000 (09:04 +0100)]
Initialize SHA buffer size var in passwd_abort
The call to hash_block in passwd_abort fails with error ENOSPC on some
systems. The reason is that the variable which specifies the size of the
buffer to contain the computed hash does not get initialized.
This patch initializes the variable with the size of the buffer.
Signed-off-by: Martin Etnestad <martin.etnestad@appeartv.com>
Tom Rini [Sun, 28 Jan 2018 14:21:53 +0000 (09:21 -0500)]
Merge git://git.denx.de/u-boot-usb
Tom Rini [Sat, 27 Jan 2018 20:22:56 +0000 (15:22 -0500)]
usb: host: Drop unused hcd_name from r8a66597-hcd.c
The variable hcd_name is unsued, drop.
Cc: Marek Vasut <marex@denx.de>
Cc: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 27 Jan 2018 20:21:47 +0000 (15:21 -0500)]
usb: Remove isp116x-hcd support
The isp116x-hcd driver is extremely long unused, so just remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sun, 28 Jan 2018 02:55:04 +0000 (21:55 -0500)]
Merge git://git.denx.de/u-boot-uniphier
Tom Rini [Sat, 27 Jan 2018 19:50:52 +0000 (14:50 -0500)]
Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-sh
Masahiro Yamada [Thu, 25 Jan 2018 04:43:19 +0000 (13:43 +0900)]
ARM: uniphier: enable HS200 support for uniphier_v8_defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Sat, 27 Jan 2018 19:48:52 +0000 (14:48 -0500)]
Merge git://git.denx.de/u-boot-usb
Tom Rini [Sat, 27 Jan 2018 19:48:41 +0000 (14:48 -0500)]
Merge git://git.denx.de/u-boot-socfpga
Marek Vasut [Sun, 7 Jan 2018 18:32:56 +0000 (19:32 +0100)]
ARM: rmobile: Convert R8A7791 Porter board to DM and DT
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sun, 7 Jan 2018 19:26:04 +0000 (20:26 +0100)]
ARM: rmobile: Enable OF_CONTROL on RCar Gen2
Since the DTs are now in place, enable OF control so that they get
bundled into the U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Wed, 17 Jan 2018 21:47:21 +0000 (22:47 +0100)]
ARM: dts: rmobile: Add SoC and board U-Boot DT extras
Add U-Boot DT extras for each SoC and board. This marks the required
nodes with u-boot,dm-pre-reloc to start clock and PRR early on while
avoiding modification of the DTs imported from Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Wed, 24 Jan 2018 14:52:56 +0000 (15:52 +0100)]
ARM: dts: rmobile: Add rudimentary R8A7790 Stout DT
The Stout board is not supported in Linux, so add a rudimentary DTS
for H2 Stout as a placeholder for when a proper DTS is available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The Stout is already being shipped over, so proper DTS for both
U-Boot and Linux will happen once it's delivered :-)