Rajeshwari Shinde [Sun, 13 Jan 2013 19:49:36 +0000 (19:49 +0000)]
I2C: S3C24X0: Resolve build error for VCMA9
This patch resolves the following build errors for I2C driver in
VCMA9:
In file included from s3c24x0_i2c.c:40:0:
s3c24x0_i2c.h:38:17: error: field 'id' has incomplete type
s3c24x0_i2c.c:70:39: error: 'CONFIG_MAX_I2C_NUM' undeclared here (not
in a function) s3c24x0_i2c.c:70:31: warning: 'i2c_bus' defined but
not used [-Wunused-variable] s3c24x0_i2c.c:72:12: warning:
'i2c_busses' defined but not used [-Wunused-variable]
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Thu, 10 Jan 2013 21:06:11 +0000 (21:06 +0000)]
EXYNOS5: Enable console multiplexing in u-boot
We enable console multiplexing and use both serial and LCD for stdout/stderr.
Initially, u-boot output console is observed via serial port.
If you also have a DP panel connected onto your SMDK5250 board,
you can switch to LCD console by typing "setenv stdout lcd".
You can always switch back to serial using "setenv stdout serial".
You can switch error console(stderr) as well, using similar commands.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Thu, 10 Jan 2013 21:06:10 +0000 (21:06 +0000)]
EXYNOS5: Make all display related code dependent on CONFIG_LCD
u-boot compilation fails for smdk5250 when we deselect CONFIG_LCD
from the main config file.
Following error was observed:
drivers/video/libvideo.o: In function `exynos_lcd_init':
/home/ajay/u-boot-samsung/drivers/video/exynos_fb.c:68: undefined reference to `lcd_set_flush_dcache'
This is because exynos video drivers have dependency on CONFIG_LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Jaehoon Chung [Thu, 27 Dec 2012 22:30:33 +0000 (22:30 +0000)]
Exynos: clock: add CLK_DIV_FSYS3 at set_mmc_clk
Mobile storage is used the CLK_DIV_FSYS3 value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Jaehoon Chung [Thu, 27 Dec 2012 22:30:32 +0000 (22:30 +0000)]
Exynos: clock: support get_mmc_clk for exynos
To get exactly clock value for mmc, support the get_mmc_clk() like
set_mmc_clk().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Tue, 8 Jan 2013 20:42:25 +0000 (20:42 +0000)]
video: Modify exynos_fimd driver to support LCD console
Currently, exynos FIMD driver is being used to support only TIZEN LOGOs.
In order to get LCD console, we need to enable half word swap feature
of FIMD and use 16 BPP.
LCD console and proprietary Logo cannot be used simultaneously.
We use "logo_on" field inside vidinfo_t structure to decide whether
user wants Logo or Console.
Define CONFIG_CMD_BMP and make logo_on = 1 to get Logo on screen.
Use logo_on = 0 to get output console on LCD.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Tue, 8 Jan 2013 20:42:24 +0000 (20:42 +0000)]
EXYNOS: Add dummy definition to fix compilation dependency on CONFIG_EXYNOS_MIPI_DSIM
When only DP is used, we need not enable CONFIG_EXYNOS_MIPI_DSIM.
But if we do not select CONFIG_EXYNOS_MIPI_DSIM, exynos_fb.c throws
error saying exynos_mipi_dsi_init() not defined. So, we add
dummy definition for exynos_mipi_dsi_init when CONFIG_EXYNOS_MIPI_DSIM
is not defined.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Tue, 8 Jan 2013 20:42:23 +0000 (20:42 +0000)]
EXYNOS5: Change parent clock of FIMD to MPLL
With VPLL as source clock to FIMD,
Exynos DP Initializaton was failing sometimes with unstable clock.
Changing FIMD source to MPLL resolves this issue.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Ajay Kumar [Tue, 8 Jan 2013 20:42:26 +0000 (20:42 +0000)]
EXYNOS5: Add support for FIMD and DP
Add panel_info structure required by LCD driver
and DP panel platdata for SMDK5250.
Add GPIO configuration for LCD.
Enable FIMD and DP support on SMDK5250.
DP Panel size: 2560x1600.
We use 16BPP resolution to get LCD console.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Simon Glass <sjg@chomium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Tue, 8 Jan 2013 21:03:40 +0000 (21:03 +0000)]
PMIC: MAX77686: Add FDT Support
This patch adds fdt support to MAX77686.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Tue, 8 Jan 2013 21:03:39 +0000 (21:03 +0000)]
EXYNOS5: Add device node for PMIC
Add device node for MAX77686
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Tue, 8 Jan 2013 21:03:38 +0000 (21:03 +0000)]
EXYNOS5: FDT: Add compatible strings for PMIC
Add required compatible information for PMIC
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 8 Jan 2013 03:48:40 +0000 (03:48 +0000)]
video:cache:fix: Enable dcache flush at LCD subsystem for Exynos based boards
lcd_set_flush_dcache(1) function is called from exynos_fb.c configuration file
to enable lcd_sync function.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Vivek Gautam [Mon, 7 Jan 2013 23:37:18 +0000 (23:37 +0000)]
SMDK5250: Enable VBus for USB 2.0 controller
This patch enables Vbus required for USB 2.0 controller.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Mon, 7 Jan 2013 23:35:05 +0000 (23:35 +0000)]
EXYNOS5: FDT: Add compatible strings for USB
Add required compatible information for USB
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Mon, 7 Jan 2013 23:35:04 +0000 (23:35 +0000)]
EXYNOS5: Add device node for USB.
This patch adds the device node required for USB
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Mon, 7 Jan 2013 23:35:03 +0000 (23:35 +0000)]
EHCI: Exynos: Add fdt support
Adding fdt support to ehci-exynos in order to parse
register base addresses from the device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:23 +0000 (20:03 +0000)]
SPI: EXYNOS: Add FDT support to driver.
This patch adds FDT support to the SPI driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:22 +0000 (20:03 +0000)]
EXYNOS5: FDT: Add SPI device node data
Add SPI device node data for exynos.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:21 +0000 (20:03 +0000)]
EXYNOS5 : FDT: Add Aliases for SPI device
This patch adds aliases for SPI.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:20 +0000 (20:03 +0000)]
EXYNOS5: FDT: Add compatible strings for SPI
Add required compatible information for SPI driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:19 +0000 (20:03 +0000)]
Sound: Add FDT support to CMD.
This patch adds FDT support to sound init in CMD.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:18 +0000 (20:03 +0000)]
Sound: WM8994: Add FDT support to codec
This patch adds FDT support to the codec.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:17 +0000 (20:03 +0000)]
Sound: Add FDT support to driver
This patch adds FDT support to the sound driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:16 +0000 (20:03 +0000)]
EXYNOS5: FDT: Add compatible strings for sound
Add required compatible information for sound driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:15 +0000 (20:03 +0000)]
EXYNOS5: FDT: Add sound and codec device node
Adds sound and codec device node parameters
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:14 +0000 (20:03 +0000)]
EXYNOS5: FDT: Add sound device node data
Add sound device node data for exynos
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:13 +0000 (20:03 +0000)]
SMDK5250: Initialise I2C using FDT
This patch initialises I2C using FDT.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:12 +0000 (20:03 +0000)]
I2C: Driver changes for FDT support
Functions added to get the I2C bus number and reset I2C bus using
FDT node.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:11 +0000 (20:03 +0000)]
EXYNOS5: FDT : Decode peripheral id
Api is added to decode peripheral id based on the interrupt number
of the peripheral.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:10 +0000 (20:03 +0000)]
FDT: Add compatible string for I2C
Add required compatible information for I2C driver.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:09 +0000 (20:03 +0000)]
EXYNOS5 : FDT: Add Aliases for I2C device
This patch adds aliases for I2C.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Wed, 26 Dec 2012 20:03:08 +0000 (20:03 +0000)]
EXYNOS5: FDT: Add I2C device node data
Add I2C device node data for exynos
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Wed, 2 Jan 2013 21:31:00 +0000 (21:31 +0000)]
arm:exynos4:pinmux: Modify the gpio function for mmc
This patch add pinmux settings for Exynos4 for mmc0 and mmc2
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Wed, 2 Jan 2013 06:06:02 +0000 (06:06 +0000)]
spl:falcon:trats Update Trats default board configuration file to support FALCON MODE
Support for a new command (defined at envs) - spl_export generates
the ATAGS image necessary for fast boot. Afterwards, it is stored
at ext4 partition.
Generated image format:
CRC [4B] SIZE [4B] PAYLOAD(ATAGS/DT) [SIZE]
Remarks:
- CRC is calculated only for PAYLOAD
- SIZE is the size of PAYLOAD
It is important to adjust ${splsize} when large image is generated.
It is defined as hex, since ext4 related commands expect it.
The ${spladdr} environment variable corresponds to
CONFIG_SYS_SPL_ARGS_ADDR
Additionally definitions for DFU have been refactored and support for
EFI has been added as well.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Sun, 7 Oct 2012 01:43:17 +0000 (01:43 +0000)]
EXYNOS: EXYNOS4X12: extract Exynos4x12 IPs clock frequency
Adds functions to extract clock frequency of Exynos4x12 IPs.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Tue, 11 Dec 2012 00:52:49 +0000 (00:52 +0000)]
SMDK5250: config: Add configuration file for SMDK5250 board
Add the configuration file for exynos5250 based SMDK5250 board.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Tue, 11 Dec 2012 00:52:48 +0000 (00:52 +0000)]
exynos5: config: Rename the smdk5250.h to exynos5250-dt.h
Create a common configuration file for all exynos5250 based boards.
Going forward we will be using DT based driver discovery for all the boards
based on Exynos5. The different boards added will have there own config.h files
which internally will include this file and specify their specific DT files.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Tue, 11 Dec 2012 00:52:47 +0000 (00:52 +0000)]
exynos5: Add DT based driver for SMC911X ethernet
Add device tree based ethernet driver for SMC911X controller on
SMDK5250 boards.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Tue, 11 Dec 2012 00:52:46 +0000 (00:52 +0000)]
fdt: exynos5: Add DT node definition for SROM and SMSC9215
Add the compatibility string and constant for the ethernet driver
so the device tree parsing code can recognize it.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Tue, 11 Dec 2012 00:52:45 +0000 (00:52 +0000)]
EXYNOS5: FDT: add initial dts file for EXYNOS5250, SMDK5250
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file currently include only ethernet devices and properties. More
devices to be added in subsequent patches.
Also add the dts file for SMDK5250 board which uses the EXYNOS5250
dts file.
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Tue, 25 Dec 2012 20:13:42 +0000 (20:13 +0000)]
EXYNOS: EXYNOS4X12: Add gpio structure for EXYNOS4X12
This patch adds gpio structure for Exynos4x12.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Tue, 25 Dec 2012 20:13:40 +0000 (20:13 +0000)]
EXYNOS: EXYNOS4X12: Add clock structure for EXYNOS4X12
This patch adds clock structure for Exynos4x12.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Chander Kashyap [Tue, 25 Dec 2012 20:13:38 +0000 (20:13 +0000)]
EXYNOS: EXYNOS4X12: Populate Exynos4x12 register addresses
This patch populates base addresses of Exynos4x12 registers.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Albert ARIBAUD [Sat, 22 Dec 2012 10:59:14 +0000 (11:59 +0100)]
Merge samsung, imx, tegra into u-boot-arm/master
This commit merges branches from samsung, imx and tegra
meant to fix merge issues between u-boot/master and
u-boot-arm/master, as well as a few manual merge fixes.
Allen Martin [Wed, 19 Dec 2012 21:02:36 +0000 (13:02 -0800)]
Merge remote-tracking branch 'u-boot/master' into u-boot-arm-merged
Conflicts:
README
arch/arm/cpu/armv7/exynos/clock.c
board/samsung/universal_c210/universal.c
drivers/misc/Makefile
drivers/power/power_fsl.c
include/configs/mx35pdk.h
include/configs/mx53loco.h
include/configs/seaboard.h
Tom Rini [Tue, 18 Dec 2012 01:39:50 +0000 (18:39 -0700)]
Merge branch 'master' of git://git.denx.de/u-boot-net
Tom Rini [Tue, 18 Dec 2012 01:39:45 +0000 (18:39 -0700)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Yoshihiro Shimoda [Sun, 4 Nov 2012 15:54:30 +0000 (15:54 +0000)]
net: sh_eth: add support for SH7752
SH7752 has two fast ethernet controllers and two gigabit ethernet
controllers. It is similar to SH7757.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Joe Hershberger [Mon, 5 Nov 2012 06:13:45 +0000 (06:13 +0000)]
net: Fix endianness bug in link-local
The ip is stored in network order, so we can't test it in host order.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Simon Glass [Thu, 11 Oct 2012 13:57:36 +0000 (13:57 +0000)]
net: Add tftp speed indication
This prints a tftp speed indication after the download completes. This
is the 3.6 MiB/s indicator below.
Tegra2 (SeaBoard) # tftp ...
Using asx0 device
TFTP from server 172.22.72.144; our IP address is 172.22.73.81
Filename '/tftpboot/uImage-user-seaboard-1'.
Load address: 0x408000
Loading: #################################################
3.6 MiB/s
done
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
trem [Sat, 6 Oct 2012 04:25:56 +0000 (04:25 +0000)]
powerpc: remove not used CONFIG_SYS_TFTP_LOADADDR
CONFIG_SYS_TFTP_LOADADDR is defined on severals boards,
but it's never used. So we can safely removed it.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Michal Simek [Tue, 7 Aug 2012 02:23:07 +0000 (02:23 +0000)]
phy: Add support for Marvell 88E1118R
Marvell 88E1118R has different uid then
88E1118.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Andy Fleming <afleming@freescale.com>
CC: Zang Roy-R61911 <tie-fei.zang@freescale.com>
CC: Kumar Gala <galak@kernel.crashing.org>
Ruchika Gupta [Thu, 19 Apr 2012 02:27:11 +0000 (02:27 +0000)]
e1000e : Correct Rx Threshold granularity
In e1000e driver, Rx descriptor queue is used such that hardware can add only
one descriptor at a time. So the WTHRESH granularity in RXDCTL should be set
to single descriptor. This would ensure that every time controller fills a Rx
descriptor, it is flushed to host memory. Earlier this granularity was in
cache line units i.e 2 descriptors. This leads to controller always waiting
for 2 descriptors before flushing them out. But since not more than one Rx BD
is actually available , the accumulation condition never gets hit.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Eric Benard [Tue, 11 Dec 2012 11:36:21 +0000 (11:36 +0000)]
m28evk/mx28evk: fix nand_update_full
- since commit
418396e212b59bf907dbccad997ff50f7eb61b16 nand write.raw
can take the number of page to be written as an argument. nand_update_full
is passing the size (in bytes) to nand write.raw. This value was previously
ignored but now breaks the write.
- this patch updates the default environment of these boards to provide a
pagecount instead of a size to nand write.raw.
- tested on a mx28evk with a 4k page NAND and on a custom board with a
2k page NAND.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Scott Wood [Fri, 14 Dec 2012 22:03:55 +0000 (16:03 -0600)]
Merge remote-tracking branch 'origin/master'
Tom Rini [Fri, 14 Dec 2012 21:43:22 +0000 (14:43 -0700)]
Prepare v2013.01-rc2
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 13 Dec 2012 20:58:27 +0000 (13:58 -0700)]
omap3_evm: Let CONFIG_EFI_PARTITION be set for SPL
The #ifdef here is not enough to stop part_efi.c from being built, only
being unused. And with recent changes this now leads to warnings. The
easiest solution here is to just let the garbage collection at link time
do its job.
Signed-off-by: Tom Rini <trini@ti.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:37 +0000 (22:16 -0600)]
env: Handle write-once ethaddr and serial# generically
Use the variable access flags to implement the protection for ethaddr
and serial# instead of hard-coding them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:36 +0000 (22:16 -0600)]
env: Implement the env delete command
Implement a way to delete more than one variable at a time.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:35 +0000 (22:16 -0600)]
env: Add setenv force support
Now that we have support for permissions, add a way to override them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:34 +0000 (22:16 -0600)]
env: Add support for access control to .flags
Add support for read-only, write-once, and change-default.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:33 +0000 (22:16 -0600)]
env: Add a command to display details about env flags
Similar to the env callback command, this will show details about the
options available, the static list, and the currently active variables.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:32 +0000 (22:16 -0600)]
tools/env: Add environment variable flags support
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address. Call
env_acl_validate_setenv_params() from setenv() in fw_env.c.
If the entry is not found in the env .flags, then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Need to build in _ctype for isdigit for Linux.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:31 +0000 (22:16 -0600)]
env: Add environment variable flags
Currently just validates variable types as decimal, hexidecimal,
boolean, ip address, and mac address.
If the entry is not found in the env ".flags", then look in the static
one. This allows the env to override the static definitions, but prevents
the need to have every definition in the environment distracting you.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:30 +0000 (22:16 -0600)]
env: Add a silent env handler
The silent variable now updates the global data flag anytime it is
changed as well as after the env relocation (in case its value is
different from the default env in such cases as NAND env)
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:29 +0000 (22:16 -0600)]
env: Add a console env handler
Remove the hard-coded console handler and use a callback instead
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:28 +0000 (22:16 -0600)]
env: Add a loadaddr env handler
Remove the hard-coded loadaddr handler and use a callback instead
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:27 +0000 (22:16 -0600)]
env: Add a baudrate env handler
Remove the hard-coded baudrate handler and use a callback instead
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:26 +0000 (22:16 -0600)]
env: Add a bootfile env handler
Remove the hard-coded bootfile handler and use a callback instead
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:25 +0000 (22:16 -0600)]
env: Add a command to view callbacks
The callbacks can be bound, but are otherwise invisible. Add a command
to show what callbacks are available.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
!!! fix callback command
Joe Hershberger [Wed, 12 Dec 2012 04:16:24 +0000 (22:16 -0600)]
env: Add support for callbacks to environment vars
Add support for per-variable callbacks to the "hashtable" functions.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
!!!fix comment in callback
Joe Hershberger [Wed, 12 Dec 2012 04:16:23 +0000 (22:16 -0600)]
env: Hide '.' variables in env print by default
When printing all variables with env print, don't print variables that
begin with '.'. If env print is called with a '-a' switch, then
include variables that begin with '.' (just like the ls command).
Variables printed explicitly will be printed even without the -a.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:22 +0000 (22:16 -0600)]
env: Use getenv_yesno() more generally
Move the getenv_yesno() to env_common.c and change most checks for
'y' or 'n' to use this helper.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:21 +0000 (22:16 -0600)]
env: Refactor apply into change_ok
Move the read of the old value to inside the check function. In some
cases it can be avoided all together and at the least the code is only
called from one place.
Also name the function and the callback to more clearly describe what
it does.
Pass the ENTRY instead of just the name for direct access to the whole
data structure.
Pass an enum to the callback that specifies the operation being approved.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:20 +0000 (22:16 -0600)]
env: Consolidate common code in hsearch_r()
The same chunk of code was replicated in two places and the following
changes will make that chunk grow a bit, so combine into a static func.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:19 +0000 (22:16 -0600)]
env: Refactor do_apply to a flag
Use a flag in hsearch_r for insert mode passed from import to allow the
behavior be different based on use.
Now that "do_check" is called for all imports, ensure console init is
complete before updating the console on relocation import
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Wed, 12 Dec 2012 04:16:18 +0000 (22:16 -0600)]
Make linux kernel string funcs available to tools
isspace() and strim() are not in the typical user-mode string.h, so
put them in a separate compilation unit so that they can be built into
tools that need them independent of the other common string functions.
This allows code shared by u-boot and the linux user-mode tools to link.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Lukasz Majewski [Tue, 11 Dec 2012 10:09:48 +0000 (11:09 +0100)]
gpt: Enable support for GPT partition table restoration at Samsung's Trats
Enable support for GPT partition table restoration at Samsung's Trats
development board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Tue, 11 Dec 2012 10:09:47 +0000 (11:09 +0100)]
gpt: Support for new "gpt" command
New command - "gpt" is supported. It restores the GPT partition table.
It looks into the given environment variable for partitions definition.
It can be enabled at target configuration file with CONFIG_CMD_GPT.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Lukasz Majewski [Tue, 11 Dec 2012 10:09:46 +0000 (11:09 +0100)]
gpt: Support for GPT (GUID Partition Table) restoration
The restoration of GPT table (both primary and secondary) is now possible.
Function 'gpt_restore' presents example of partition restoration process.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Chang Hyun Park [Tue, 11 Dec 2012 10:09:45 +0000 (11:09 +0100)]
gpt: The leXX_to_int() calls replaced with ones defined at <compiler.h>
Custom definitions of le_XX_to_int functions have been replaced with
standard ones, defined at <compiler.h>
Replacement of several GPT related structures members with ones
indicating its endianness and proper size.
Signed-off-by: Chang Hyun Park <heartinpiece@outlook.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Lukasz Majewski [Tue, 11 Dec 2012 10:09:44 +0000 (11:09 +0100)]
gpt:doc: GPT (GUID Partition Table) documentation
Documentation of the GPT format.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Lukasz Majewski [Tue, 11 Dec 2012 10:09:43 +0000 (11:09 +0100)]
part:efi: Move part_efi.h file to ./include
This move is necessary to export gpt header and GPT partition entries to be
used with other commands or subsystems.
Additionally the part_efi.h file has been cleaned-up to supress checkpatch's
warnings.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Lukasz Majewski [Tue, 11 Dec 2012 10:09:42 +0000 (11:09 +0100)]
vsprintf:fix: Change type returned by ustrtoul
The ustrtoul shall convert string defined size (e.g. 1GiB) to unsigned
long type (as its name implies).
Up till now it had returned int, which might cause problems with large
numbers (GiB range), when interpreted as U2 signed numbers.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fabio Estevam [Tue, 11 Dec 2012 11:48:46 +0000 (11:48 +0000)]
mx25pdk: Allow booting a device tree kernel
Select CONFIG_OF_LIBFDT so that a device tree kernel can be launched.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Tue, 11 Dec 2012 06:36:58 +0000 (06:36 +0000)]
mx53loco: Fix PMIC name
commit
c73368150 (pmic: Extend PMIC framework to support multiple instances
of PMIC devices) has incorrectly passed the PMIC name under the FSL PMIC case.
Fix that by passing "FSL_PMIC" as the parameter of pmic_get.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tom Rini [Wed, 12 Dec 2012 13:51:02 +0000 (06:51 -0700)]
Merge branch 'master' of git://git.denx.de/u-boot-mips
Joe Hershberger [Tue, 11 Dec 2012 17:52:50 +0000 (17:52 +0000)]
mips: serial: Fix busted manual relocation
serial_initialize() must be called after relocation to adjust the
pointers to putc(), getc(), etc. This is busted ever since the
serial driver-model-ification series.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Daniel Schwierzeck [Wed, 12 Dec 2012 12:13:48 +0000 (13:13 +0100)]
MIPS: constify mips_io_port_base
mips_io_port_base is exported as 'extern const unsigned long mips_io_port_base;'
in arch/mips/include/asm/io.h. Thus make the variable const too.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Wolfram Sang [Wed, 5 Dec 2012 10:48:47 +0000 (10:48 +0000)]
mtd: nand: mxs: reset BCH earlier, too, to avoid NAND startup problems
It could happen (1 out of 100 times) that NAND did not start up correctly after
warm rebooting, so we end up with various failures or DMA timed out due to a
stalled BCH. When resetting BCH together with GPMI, the issue could not be
observed anymore (after 10000+ reboots). We probably need the consistent state
already before sending commands to NAND. This behaviour was observed in barebox
and kernel, so I assume it affects U-Boot as well. I chose to keep the extra
reset for BCH when changing the flash layout to be on the safe side.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
Łukasz Majewski [Thu, 6 Dec 2012 05:23:38 +0000 (05:23 +0000)]
cmd:spl:fix: Prevent from a build error on boards, which don't support FDT
Do not compile in FDT related code, when it is not supported.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Simon Glass [Wed, 5 Dec 2012 14:46:45 +0000 (14:46 +0000)]
exynos: Enable hashing functions and EDID for smdk5250
Enable SHA1/SHA256 hashing and the hash command. Also enable EDID
support for reading from an LCD.
Signed-off-by: Simon Glass <sjg@chromium.org>
Luigi Semenzato [Wed, 5 Dec 2012 14:46:44 +0000 (14:46 +0000)]
tpm: Add TPM stress test
Add a simple command to stress-test a TPM (Trusted Platform Module).
Signed-off-by: Luigi Semenzato <semenzato@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 5 Dec 2012 14:46:43 +0000 (14:46 +0000)]
console: Enable function to display console info
The CONFIG_SYS_CONSOLE_INFO_QUIET option should suppress the console
information, but allow boards to display it later if required. Adjust
the code to support this.
This is used to avoid printing the information while the LCD display
is not ready, since it only becomes ready when stdio init is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
Vadim Bendebury [Wed, 5 Dec 2012 14:46:42 +0000 (14:46 +0000)]
Add console command to access io space registers
Provide u-boot console functions to access IO space registers. A no
thrills implementation, accessing one register at a time.
For example:
boot > iod 80
0080:
00000094
boot > iod.w 80
0080: 0094
boot > iod.b 80
0080: 94
boot > iow.b 0x80 12
boot > iod 0x80
0080:
00000012
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Wai-Hong Tam [Wed, 5 Dec 2012 14:46:41 +0000 (14:46 +0000)]
fdt: edid: Enable fdt_add_edid() function when CONFIG_LCD defined
This function can be used for LCDs as well as monitors.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Wai-Hong Tam [Wed, 5 Dec 2012 14:46:40 +0000 (14:46 +0000)]
edid: Add I2C command for printing the EDID
Add a single command to read the EDID information over I2C.
For example:
SMDK5250 # i2c dev 7
Setting bus to 7
SMDK5250 # i2c edid 50
EDID version: 1.4
Product ID code: 305c
Manufacturer: AUO
Serial number:
00000000
Manufactured in week: 0 year: 2011
Video input definition: digital signal, voltage level 0, blank to black
Monitor is non-RGB
Maximum visible display size: 26 cm x 14 cm
Power management features: no active off, no suspend, no standby
Estabilished timings:
Standard timings:
1366x768 60 Hz (detailed)
1366x768 60 Hz (detailed)
Monitor ID: 2VD2K.B116XW
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tom Wai-Hong Tam [Wed, 5 Dec 2012 14:46:39 +0000 (14:46 +0000)]
edid: Library of EDID decode and print
This implements a library for accessing EDID data from an LCD panel.
This is used to obtain information about the panel such as its
resolution and type.
This is a tidied-up version of the original code pulled from
https://github.com/ynezz/u-boot-edid.
The changes we made are:
- removed bit fields in the struct;
- removed endianness cases in the struct;
- fixed some wrong definitions;
- fixed to fit 80 columns;
- fixed some code styles.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 5 Dec 2012 14:46:38 +0000 (14:46 +0000)]
Add hash command to perform hashing using various algorithms
This new command supports hashing SHA1 and SHA256. It could be extended
to others such as MD5 and the CRC algorithms. The syntax is modeled on
those:
hash <algorithm> <address> <length> [*<dest_addr> | <dest_envvar>]
to calculate a hash, and:
hash -v <algorithm> <address> <length> [*<verify_addr> | <verify_envvar>]
to verify a hash.
Use CONFIG_CMD_HASH to enable the command, CONFIG_SHA1 to enable SHA1 and
CONFIG_SHA256 to enable SHA256.
The existing sha1sum command remains.
Signed-off-by: Simon Glass <sjg@chromium.org>
projects / oweals / u-boot.git / log