arm64: zynqmp: Add support for verifying secure images

This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Remove ep108 board

ZynqMP Emulation board is no longer tested and there is no reason to
keep maintaining it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Correct EG/EV part detection logic

The vcu disable bit in efuse ipdisable register is valid only
if PL powered up so, consider PL powerup status for determing
EG/EV part. If PL is not powered up, ignore EG/EV part of string.
The PL powerup status will be filled by pmufw based on PL PROGB
status in the 9th bit of version field.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Print the value of pl clocks and wdt clock using clk dump

This patch print pl clocks (pl0...pl3) and watchdog
clock using clk dump.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: nand: Fixed NAND erase issue for size 1GiB or more

NAND erase was not happening for size 1GiB or more. Erase
command was executing successfully but in actual, it was not
erasing.
This patch fixed erase issue for 1 GiB or more size nand.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Remove OF_EMBED configuration for zc770 xm011 x16

Use appended dtb which is default option for zynq boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Setup the same bootcommand as for zc770 xm011 x8

The same command should be used for x16 configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Changed scratch address used by the alternate memory test

This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the
accessible DDR address used by alternate memory test.
Before this, 0xfffc0000 address was used, which is the OCM
address and not enabled in MMU table. So, whenever trying
to access 0xfffc0000 address, got Synchronous Abort exception.

After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate
memory test is working fine.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Enable cadence driver on zc706

Enable watchdog with reset-on-timeout feature.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Wire watchdog internals

Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

watchdog: Add Cadence watchdog driver

This IP can be found on Zynq and ZynqMP devices.
The driver was tested with reset-on-timeout; feature.

Also adding WATCHDOG symbol to Kconfig because it is required.

Signed-off-by: Shreenidhi Shedi <imshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

clk: zynq: Show watchdog clock rate properly

watchdog clock is also connected to cpu 1X clocksource.

Zynq> clk dump
...

Before:
      swdt          4294967290
After:
      swdt           111111110

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Enable newer pmufw versions

As of now newer pmufw is keeping old interfaces. That's why permit
u-boot to run on newer version. Recommended version will be setup later.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

net: zynq_gem: Dont run any phy detection logic for GMII case

This patch bypasses phy detection logic for GMII interface
and just depend on phy address received from DT. This patch
is required as phy detection logic is different for some phys
like xilinx phy which can be connected over SGMII and GMII
interface.
This fixes the issue of ethernet failures when xilinx phy is
connected over GMII interface.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

arm64: zynqmp: Add support to load an app at EL1

This patch is adding support to switch to EL1 while loading an EL1
application with u-boot running at EL above EL1 in aarch64 mode.

Signed-off-by: Nitin Jain <nitinj@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm: zynq: Enable debug uart on Zedboard

It helps with debugging.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Enable ethernet driver for zc1751-dc5

Enable missing driver on this board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

fpga: Simplify error path in fpga_add

Check !desc earlier to simplify code.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>

xilinx: Sync defconfigs with latest Kconfig updates

Make defconfigs up2date with current location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

arm64: zynqmp: Convert board to use zynqmp-clk driver

Use zynqmp clock driver instead of fixed clocks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Merge git://git.denx.de/u-boot-net

configs: omapl138: Enable DM and DT

Enable Driver Model and Device-tree support for omapl138 board
in U-Boot. Also enable DM_SERIAL and DM_I2C.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

ARM: dts: da850-lcdk: Sync from Linux 4.16

Sync dts from Linux 4.16 and also add u-boot specific
dtsi for OMAPl138 board.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

davinci: Enable DDR_INIT for DA8XX

Commit 6aa4ad8e3820 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
converted SOC_DA8XX to Kconfig but missed enabling DDR_INIT for
SOC_DA8XX, which broke OMAPL138 to boot.

Commit 2e87980580d0 ("davinci: Fix omapl138_lcdk builds") disabled
DDR_INIT for all DA850 SoCs. This failed all DA850 boards to boot
as ddr is not being initialized.

Enable SYS_DA850_DDR_INIT for DA8XX so that all DA850 and OMAPL138
will have ddr initialized

Fixes: 2e87980580d0 ("davinci: Fix omapl138_lcdk builds")
Fixes: 6aa4ad8e3820 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

configs: am335x_evm: Increase SPL_SYS_MALLOC_F_LEN to accomodate gpio_devices

With gpio devices getting created in SPL, the size of the heap is
no longer sufficient. Therefore, increase SPL_SYS_MALLOC_F_LEN
to 0x1000.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

gpio: omap_gpio: Add DM_FLAG_PRE_RELOC flag

With DM enabled in SPL, DM_FLAG_PRE_RELOC is required for
the omap_gpio driver to be bound to the gpio devices.

Therefore, add DM_FLAG_PRE_RELOC flag to the omap_gpio driver.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

scripts/check-config.sh: fix "command not found" error handling

scripts/check-config.sh exits successfully and silently without doing
any checks when the 'comm' command is not found.

The problem triggers from the command around line 39:

  comm -23 ${suspects} ${ok} >${new_adhoc}

This statement fails when 'comm' is not in $PATH, creating an empty
${new_adhoc} file. But the script continues and the following line,
which is supposed to detect an error:

  if [ -s ${new_adhoc} ]; then

will always be false since the file is empty, and the script will exit
successfully as if everything were OK.

The case where 'comm' in not in $PATH is not theoretical. It used to
happen on yocto until a recent fix [0], and still happens on the
current stable branch (rocko).

Fix by setting the errexit flag to exit with error when a statement
fails, so that at least the problem is noticed.

For additional safety also set the nounset flag to detect expansion
errors.

[0] http://git.yoctoproject.org/cgit/cgit.cgi/poky/commit/?id=fe0b4cb5b48580d4a3f3c0eb82bfa6f1b13801e4

Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Simon Glass <sjg@chromium.org>

davinci: omapl138_lcdk: fix PLL0 frequency

commit 1601dd97edc6 ("davinci: omapl138_lcdk: increase PLL0 frequency")
changed the PLL0 frequency to 456MHz, which is needed for the LCDC IP
block. However, in doing so, it caused the PLLOUT clock to be outside
of the allowable specifications given in the OMAP-L138 data sheet. (It
says PLLOUT must be 600MHz max). It also uses a PLLM value outside of
the range given in the TRM (it says PLLM must in the range 0 to 0x1f).

So here is what we have currently:

PLLOUT = 24 / (0 + 1) * (37 + 1) = 912MHz (out of spec)
         ^     ^         ^
       CLKIN PREDIV    PLLM (out of spec)

input to PLLDIVn = 912 / (1 + 1) = 456MHz (desired result)
                    ^     ^
                 PLLOUT POSTDIV

This changes the PLLM value to 18 and the POSTDIV value to 0 so that
PLLOUT is now within specification but we still get the desired
result.

PLLOUT = 24 / (0 + 1) * (18 + 1) = 456MHz (within spec)
         ^     ^         ^
       CLKIN PREDIV     PLLM

input to PLLDIVn = 456 / (0 + 1) = 456MHz (desired result)
                    ^     ^
                 PLLOUT POSTDIV

Fixes: 1601dd97edc6 ("davinci: omapl138_lcdk: increase PLL0 frequency")
Signed-off-by: David Lechner <david@lechnology.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>

test/py: add spi_flash tests

Add basic tests for the spi_flash subsystem.

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

net: Drop CONFIG_ENC28J60

Last user of this driver went away in October 2014 in
commit d58a9451e7339ed4 ("ppc/arm: zap EMK boards").

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: macb: remove superfluous logical constraint

In

if (a > =0) {...}
else (a < 0) {...}

the second logical constraint is superfluous.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: cpsw: remove superfluous assignment.

In

int ret = A;
ret = B;

the first assignment has not effect.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

lan7xxx: Require phylib

The lan75xx and lan78xx drivers need to drive their phy via the generic
phylib framework. Let's reflect that dependency in Kconfig, so that we
don't get build errors when phylib does not get selected.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: Only access network devices after init

In the efi_loader main loop we call eth_rx() occasionally. This rx function
might end up calling into devices that haven't been initialized yet,
potentially resulting in a lot of transfer timeouts.

Instead, let's make sure the ethernet device is actually initialized before
reading from or writing to it.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: Fix netretry condition

The "net_try_count" counter starts from "1".
And the "retrycnt" contains requested amount of retries.

With current logic, that means that the actual retry amount
will be one time less then what we set in "netretry" env.
For example setting "netretry" to "once" will make "retrycnt"
equal "1", so no retries will be triggered at all.

Fix the logic by changing the statement of "if" condition.

Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net/phy/cortina: Add No firmware upload option

Current Cortina phy driver assumes that firmware upload
is required during initialization and is dependent
on presence of corresponding macros like CONFIG_CORTINA_FW_ADDR
for compilation.

But Cortina phy has provision to store phy firmware in
attached dedicated EEPROM. And boards designed with such
EEPROM does not require firmware upload.

Add CORTINA_NO_FW_UPLOAD option in cortina.c to support
such boards.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net/phy/cortina.c: Update get_phy_id implementation

Update get_phy_id() implementation in cortina.c to check
for Cortina_phy by comparing device phy_id with cortina phy_id
instead of relying on presence of CORTINA macros.

This will allow get_phy_id to work with non-cortina phy devices
which might have same phy address as Cortina device but on
different  bus.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

configs: ls1012a: add pfe configuration for LS1012A

Add configurations for PFE.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

armv8: layerscape: csu: enable ns access to PFE registers

Enable all types of non-secure access to PFE block registers.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

armv8: fsl-lsch2: configure pfe's DDR and HDBUS interfaces and ECC

1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces
to bufferable.
2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces.
3. Disable ECC detection for PFE.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

armv8: fsl-lsch2: add pfe macros and update ccsr_scfg structure

SoC specific PFE macros are defined and structure ccsr_scfg
is updated with members defined for PFE.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

board: freescale: ls1012a2g5rdb: enable network support on ls1012a2g5rdb

This patch enables ethernet support for ls1012a2g5rdb.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

board: freescale: ls1012ardb: enable network support on ls1012ardb

This patch enables ethernet support for ls1012ardb.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

board: freescale: ls1012afrdm: enable network support on ls1012afrdm

This patch enables ethernet support for ls1012afrdm.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

board: freescale: ls1012aqds: enable network support on ls1012aqds

This patch enables ethernet support for ls1012aqds.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: pfe_eth: LS1012A PFE headers

Contains all the pfe header files.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: pfe_eth: provide pfe commands

pfe_command provides command line support for several features that
support pfe, like starting or stopping the pfe, checking the health
of the processor engines and checking status of different units inside
pfe.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: pfe_eth: LS1012A PFE driver introduction

This patch adds PFE driver to U-Boot

Following are the main driver files:-
pfe_hw.c: provides low level helper functions to initialize PFE
internal processor engines and other hardware blocks
pfe_driver.c: provides initialization functions
and packet send and receive functions
pfe_eth.c: provides high level gemac initialization functions
pfe_firmware.c: provides functions to load firmware into PFE
internal processor engines.
pfe_mdio.c: provides functions to initialize phy and mdio.

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

armv8: fsl-layerscape: Add support of GPIO structure

Layerscape Gen2 SoC supports GPIO registers to control GPIO
signals. Adding support of GPIO structure to access GPIO
registers.

Signed-off-by: Pratiyush Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

drivers: net: phy: Fix aquantia compilation with DM

With CONFIG_DM_ETH enabled, aquantia driver compilation fails with
below error. This patch fixes the issue by including dm.h.

drivers/net/phy/aquantia.c: In function ‘aquantia_startup’:
drivers/net/phy/aquantia.c:73:21: error: dereferencing pointer to
incomplete
type ‘struct udevice’
          phydev->dev->name);
     ^~

Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: mvpp2x: add check after calloc

After allocating plat the pointer is checked.
Afterwards name is allocated and not checked.

Add the missing check to avoid a possible NULL dereference.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Configs: Use the newly added PHY_RTL8211E_PINE64_GIGABIT_FIX

The Pine64+ uses a generic PHY driver, so flip it over to using the
Realtek PHY driver to actually apply the RTL8211e fix.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.

Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

test/py: add generic CRC32 function

Add a generic function which can be used to compute the CRC32 value of
a region of RAM.

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

test/py: do not import pytest multiple times

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

test/py: README: add HOSTNAME to PYTHONPATH

As opposed to PATH, HOSTNAME is not appended to PYTHONPATH
automatically. Lets add it to the examples to make it more
obvious to new users.

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

test/py: README: fix typo

Fix a minor typo causing vim (and possibly other) to get confused with
coloring.

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

cmd: sf: fix map_physmem check

Make sure 0x00 is a valid address to read to. If `addr` is 0x00 then
map_physmem() will return 0 which should be a valid address.

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

spi: spi_flash: do not fail silently on bad user input

Make sure the user is notified instead of silently returning an error.

Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>

tools: Make kwboot build if HOST_TOOLS_ALL=y

The kwboot tool for Marvell devices isn't currently being built even if
HOST_TOOLS_ALL is set. It doesn't appear to depend on any CONFIG_
options, so it seems appropriate to enable building it here.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

Merge git://git.denx.de/u-boot-mips

mips: bmips: add ar-5315 usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add support for bcm6318 usb

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

phy: add support for bcm6318 usbh phy

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

mips: bmips: add vr-3032u usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add support for bcm63268 usb

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add dgnd3700v2 usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add support for bcm6362 usb

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add ar-5387un usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add support for bcm6328 usb

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add wap-5813n usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add support for bcm6368 usb

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

phy: add support for bcm6368 usbh phy

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

mips: bmips: add nb4-ser usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add hg556a usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add support for bcm6358 usb

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

phy: add support for bcm6358 usbh phy

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

mips: bmips: add ct-5361 usb support

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

mips: bmips: add support for bcm6348 usb

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>

phy: add support for bcm6348 usbh phy

Signed-off-by: Ã\81lvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

mips: micronas/vct: check array bounds before access

If we check an index against array bounds, we should do so before
accessing the array and not afterwards.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>

mips: bmips: select OF_EMBED for all boards

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

MIPS: add BMIPS Netgear DGND3700v2 board

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

MIPS: add support for Broadcom MIPS BCM6362 SoC family

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

dm: cpu: bmips: add BCM6362 support

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

Merge git://git.denx.de/u-boot-fsl-qoriq

LS2088ARDB: Secure Boot: Fix fall back option failure

Fix NOR, SD and QSPI fallback option in case of secure boot failure.

Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088aqds: Add IFC-NOR as boot source for LS1088

IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.

Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088a: Add i2c_early_init() func for LS1088AQDS

This function is required for enabling access to early i2c function
for correct usage of QIXIS_READ and QIXIS_WRITE.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088a: Add clock related function in CONFIG_SPL_BUILD

get_board_ddr_clk(), get_board_sys_clk() and if_board_diff_clk() is
now available for SPL build.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088qds: Remove CONFIG_ from local defines for FPGA

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Merge git://git.denx.de/u-boot-usb

Merge git://git.denx.de/u-boot-sunxi

bootm: optee: Add a bootm command for type IH_OS_TEE

This patch makes it possible to verify the contents and location of an
OPTEE image in DRAM prior to handing off control to that image. If image
verification fails we won't try to boot any further.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Andrew F. Davis <afd@ti.com>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>

image: Add IH_OS_TEE for TEE chain-load boot

This patch adds a new type IH_OS_TEE. This new OS type will be used for
chain-loading to Linux via a TEE.

With this patch in-place you can generate a bootable OPTEE image like this:

mkimage -A arm -T kernel -O tee -C none -d tee.bin uTee.optee

where "tee.bin" is the input binary prefixed with an OPTEE header and
uTee.optee is the output prefixed with a u-boot wrapper header.

This image type "-T kernel -O tee" is differentiated from the existing
IH_TYPE_TEE "-T tee" in that the IH_TYPE is installed by u-boot (flow
control returns to u-boot) whereas for the new IH_OS_TEE control passes to
the OPTEE firmware and the firmware chainloads onto Linux.

Andrew Davis gave the following ASCII diagram:

IH_OS_TEE: (mkimage -T kernel -O tee)
Non-Secure       Secure

                 BootROM
                   |
      -------------
     |
     v
    SPL
     |
     v
   U-Boot ------>
          <-----  OP-TEE
      |
      V
    Linux

IH_TYPE_TEE: (mkimage -T tee)
Non-Secure       Secure

                 BootROM
                   |
      -------------
     |
     v
    SPL ------->
         <-----  OP-TEE
     |
     v
   U-Boot
      |
      V
    Linux

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Andrew F. Davis <afd@ti.com>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Link: http://mrvan.github.io/optee-imx6ul

optee: Add error printout

When encountering an error in OPTEE verification print out various details
of the OPTEE header to aid in further debugging of encountered errors.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>

optee: Add optee_verify_bootm_image()

This patch adds optee_verify_bootm_image() which will be subsequently used
to verify the parameters encoded in the OPTEE header match the memory
allocated to the OPTEE region, OPTEE header magic and version prior to
handing off control to the OPTEE image.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>

optee: Add optee_image_get_load_addr()

This patch adds optee_image_get_load_addr() a helper function used to
calculate the load-address of an OPTEE image based on the lower
entry-point address given in the OPTEE header.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>

optee: Add optee_image_get_entry_point()

Add a helper function for extracting the least significant 32 bits from the
OPTEE entry point address, which will be good enough to load OPTEE binaries
up to (2^32)-1 bytes.

We may need to extend this out later on but for now (2^32)-1 should be
fine.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>

optee: Add CONFIG_OPTEE_LOAD_ADDR

CONFIG_OPTEE_LOAD_ADDR is used to tell u-boot where to load the OPTEE
binary into memory prior to handing off control to OPTEE.

We need to pull this value out of u-boot in order to produce an IMX IVT/CSF
signed pair for the purposes of secure boot. The best way to do that is to
have CONFIG_OPTEE_LOAD_ADDR appear in u-boot.cfg.

Adding new CONFIG entires to u-boot should be kconfig driven so this patch
does just that.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>