oweals/u-boot.git
11 years agoMIPS: mips32/cache.S: save return address in t9 register
Gabor Juhos [Thu, 13 Jun 2013 10:59:34 +0000 (12:59 +0200)]
MIPS: mips32/cache.S: save return address in t9 register

Synchronize the code with mips64/cache.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: xburst/start.S: rework relocation info check
Gabor Juhos [Fri, 14 Jun 2013 12:47:10 +0000 (14:47 +0200)]
MIPS: xburst/start.S: rework relocation info check

Make it similar to the code in mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: xburst/start.S: use t8 register for dynamic relocation
Gabor Juhos [Thu, 13 Jun 2013 10:59:32 +0000 (12:59 +0200)]
MIPS: xburst/start.S: use t8 register for dynamic relocation

Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: xburst/start.S: save gd in s0 register
Gabor Juhos [Thu, 13 Jun 2013 10:59:31 +0000 (12:59 +0200)]
MIPS: xburst/start.S: save gd in s0 register

Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: xburst/start.S: save relocation offset in s1 register
Gabor Juhos [Thu, 13 Jun 2013 10:59:30 +0000 (12:59 +0200)]
MIPS: xburst/start.S: save relocation offset in s1 register

Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: xburst/start.S: save relocation address in s2 register
Gabor Juhos [Thu, 13 Jun 2013 10:59:29 +0000 (12:59 +0200)]
MIPS: xburst/start.S: save relocation address in s2 register

Synchronize the code with mips{32,64}/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: mips32/start.S: rework relocation info check
Gabor Juhos [Thu, 13 Jun 2013 10:59:28 +0000 (12:59 +0200)]
MIPS: mips32/start.S: rework relocation info check

Make it similar to the code in mips64/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: mips32/start.S: use t8 register for dynamic relocation
Gabor Juhos [Thu, 13 Jun 2013 10:59:27 +0000 (12:59 +0200)]
MIPS: mips32/start.S: use t8 register for dynamic relocation

Synchronize the code with mips64/start.S, in order to
allow further unifications.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: mips32/cache.S: remove superfluous register assignment
Gabor Juhos [Wed, 12 Jun 2013 16:02:46 +0000 (18:02 +0200)]
MIPS: mips32/cache.S: remove superfluous register assignment

The t4 register already holds the cache
line size, and the value of the register
is not changed in mips_init_icache.

Get the cache line size value from t4 for
mips_init_dcache as well and remove the
superfluous assignment of t5 register.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
11 years agoMIPS: remove obsolete TODO items
Gabor Juhos [Wed, 12 Jun 2013 16:02:45 +0000 (18:02 +0200)]
MIPS: remove obsolete TODO items

The MIPS  code uses centralized u-boot.lds script already,
and dynamic relocation is supported as well.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: mips64/interrupt.c: remove superfluous include
Gabor Juhos [Wed, 12 Jun 2013 16:02:44 +0000 (18:02 +0200)]
MIPS: mips64/interrupt.c: remove superfluous include

Nothing is used from asm/mipsregs.h.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: mips32/time.c: fix checkpatch errors/warnings
Gabor Juhos [Wed, 12 Jun 2013 16:02:43 +0000 (18:02 +0200)]
MIPS: mips32/time.c: fix checkpatch errors/warnings

Checking mips32/time.c with checkpatch.pl shows this:

  arch/mips/cpu/mips32/time.c:30: WARNING: line over 80 characters
  arch/mips/cpu/mips32/time.c:57: ERROR: return is not a function, parentheses are not required
  total: 1 errors, 1 warnings, 0 checks, 85 lines checked

Fix the code to make checkpatch.pl happy.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: qemu-malta: bring up ethernet
Gabor Juhos [Wed, 22 May 2013 03:57:44 +0000 (03:57 +0000)]
MIPS: qemu-malta: bring up ethernet

Qemu emulates a PCNET PCI card for the Malta CoreLV board.
Enable the pcnet driver and add board specific ethernet
initialization function to bring it up. Also enable the
CONFIG_CMD_NET and CONFIG_CMD_PING options.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: qemu-malta: add PCI support
Gabor Juhos [Wed, 22 May 2013 03:57:42 +0000 (03:57 +0000)]
MIPS: qemu-malta: add PCI support

Qemu emulates the Galileo GT64120 System Controller
which provides a CPU bus to PCI bus bridge.

The patch adds driver for this bridge and enables
PCI support for the emulated Malta board.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: qemu-malta: setup GT64120 registers as done by YAMON
Gabor Juhos [Wed, 22 May 2013 03:57:41 +0000 (03:57 +0000)]
MIPS: qemu-malta: setup GT64120 registers as done by YAMON

Move the GT64120 register base to 0x1be00000
and setup PCI BAR registers as done by the
original YAMON bootloader.

This is needed for running Linux kernel.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: qemu-malta: enable flash support
Gabor Juhos [Wed, 22 May 2013 03:57:39 +0000 (03:57 +0000)]
MIPS: qemu-malta: enable flash support

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: qemu-malta: add reset support
Gabor Juhos [Wed, 22 May 2013 03:57:38 +0000 (03:57 +0000)]
MIPS: qemu-malta: add reset support

The MIPS Malta board has a SOFTRES register. Writing a
magic value into that register initiates a board reset.

Use this feature to implement reset support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: qemu-malta: add support for emulated MIPS Malta board
Gabor Juhos [Wed, 22 May 2013 03:57:37 +0000 (03:57 +0000)]
MIPS: qemu-malta: add support for emulated MIPS Malta board

Add minimal support for the MIPS Malta CoreLV board
emulated by Qemu. The only supported peripherial is
the UART.

This is enough to boot U-Boot to the command prompt
both in little and big endian mode.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: start.S: emulate REVISION register for qemu-malta
Gabor Juhos [Wed, 22 May 2013 03:57:46 +0000 (03:57 +0000)]
MIPS: start.S: emulate REVISION register for qemu-malta

On the origial Malta boards the REVISION register is
accessible at the 0x1fc00010 address. The contents of
this register gives information about the revision
of the Malta and Core Boards.

This register is used by the Linux kernel to identify
the actual board it is running on. However the register
is not emulated properly by Qemu, so put a hardcoded
value into the flash to make Linux work.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: import gt64120.h header from Linux
Gabor Juhos [Wed, 22 May 2013 03:57:40 +0000 (03:57 +0000)]
MIPS: import gt64120.h header from Linux

The Linux specific register access macros, the
extern function declarations and the UL suffixes
has been removed.

The header file will be used for the qemu-malta
board.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agonet: pcnet: use pci_virt_to_mem to obtain buffer addresses
Gabor Juhos [Wed, 22 May 2013 03:57:43 +0000 (03:57 +0000)]
net: pcnet: use pci_virt_to_mem to obtain buffer addresses

The pcnet driver uses the pci_phys_to_mem function
to get the memory address of the DMA buffers. This
This assumes an 1:1 mapping between the PCI and
physical memory which is not true on all platforms.

On MIPS platform U-Boot is running within a mapped
memory region, and the pci_phys_to_mem macro can't
be used to obtain the memory address of the buffers.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
11 years agoMIPS: mips64: fix typos in copyright text of start.S
Tom Rini [Wed, 24 Jul 2013 13:50:52 +0000 (09:50 -0400)]
MIPS: mips64: fix typos in copyright text of start.S

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Conflicts:

arch/mips/cpu/mips64/start.S

Signed-off-by: Tom Rini <trini@ti.com>
11 years agoAdd eCos-2.0 SPDX-License-Identifier to source files
Wolfgang Denk [Mon, 8 Jul 2013 10:11:35 +0000 (12:11 +0200)]
Add eCos-2.0 SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
11 years agoAdd LGPL-2.0+ SPDX-License-Identifier to source files
Wolfgang Denk [Mon, 8 Jul 2013 09:58:49 +0000 (11:58 +0200)]
Add LGPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
11 years agoAdd LGPL-2.1+ SPDX-License-Identifier to source files
Wolfgang Denk [Mon, 8 Jul 2013 09:48:07 +0000 (11:48 +0200)]
Add LGPL-2.1+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
11 years agoAdd GPL-2.0+ SPDX-License-Identifier to source files
Wolfgang Denk [Mon, 8 Jul 2013 07:37:19 +0000 (09:37 +0200)]
Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
11 years agoLicenses: introduce SPDX Unique Lincense Identifiers
Wolfgang Denk [Fri, 21 Jun 2013 08:22:36 +0000 (10:22 +0200)]
Licenses: introduce SPDX Unique Lincense Identifiers

Like many other projects, U-Boot has a tradition of including big
blocks of License headers in all files.  This not only blows up the
source code with mostly redundant information, but also makes it very
difficult to generate License Clearing Reports.  An additional problem
is that even the same lincenses are referred to by a number of
slightly varying text blocks (full, abbreviated, different
indentation, line wrapping and/or white space, with obsolete address
information, ...) which makes automatic processing a nightmare.

To make this easier, such license headers in the source files will be
replaced with a single line reference to Unique Lincense Identifiers
as defined by the Linux Foundation's SPDX project [1].  For example,
in a source file the full "GPL v2.0 or later" header text will be
replaced by a single line:

        SPDX-License-Identifier:        GPL-2.0+

We use the SPDX Unique Lincense Identifiers here; these are available
at [2].

Note: From the legal point of view, this patch is supposed to be only
a change to the textual representation of the license information,
but in no way any change to the actual license terms. With this patch
applied, all files will still be licensed under the same terms they
were before.

Note 2: The apparent difference between the old "COPYING" and the new
"Licenses/gpl-2.0.txt" only results from switching to the upstream
version of the license which is differently formatted; there are not
any actual changes to the content.

Note 3: There are some recurring questions about linense issues, such
as:
    - Is a "All Rights Reserved" clause a problem in GPL code?
    - Are files without any license header a problem?
    - Do we need license headers at all?

The following excerpt from an e-mail by Daniel B. Ravicher should help
with these:

| Message-ID: <4ADF8CAA.5030808@softwarefreedom.org>
| Date: Wed, 21 Oct 2009 18:35:22 -0400
| From: "Daniel B. Ravicher" <ravicher@softwarefreedom.org>
| To: Wolfgang Denk <wd@denx.de>
| Subject: Re: GPL and license cleanup questions
|
| Mr. Denk,
|
| Wolfgang Denk wrote:
| > - There are a number of files which do not include any specific
| > license information at all. Is it correct to assume that these files
| > are automatically covered by the "GPL v2 or later" clause as
| > specified by the COPYING file in the top level directory of the
| > U-Boot source tree?
|
| That is a very fact specific analysis and could be different across the
| various files.  However, if the contributor could reasonably be expected
| to have known that the project was licensed GPLv2 or later at the time
| she made her contribution, then a reasonably implication is that she
| consented to her contributions being distributed under those terms.
|
| > - Do such files need any clean up, for example should we add GPL
| > headers to them, or is this not needed?
|
| If the project as a whole is licensed under clear terms, you need not
| identify those same terms in each file, although there is no harm in
| doing so.
|
| > - There are other files, which include both a GPL license header
| > _plus_ some copyright note with an "All Rights Reserved" clause. It
| > has been my understanding that this is a conflict, and me must ask
| > the copyright holders to remove such "All Rights Reserved" clauses.
| > But then, some people claim that "All Rights Reserved" is a no-op
| > nowadays. License checking tools (like OSLC) seem to indicate this is
| > a problem, but then we see quite a lot of "All rights reserved" in
| > BSD-licensed files in gcc and glibc. So what is the correct way to
| > deal with such files?
|
| It is not a conflict to grant a license and also reserve all rights, as
| implicit in that language is that you are reserving all "other" rights
| not granted in the license.  Thus, a file with "Licensed under GPL, All
| Rights Reserved" would mean that it is licensed under the GPL, but no
| other rights are given to copy, modify or redistribute it.
|
| Warm regards,
| --Dan
|
| Daniel B. Ravicher, Legal Director
| Software Freedom Law Center (SFLC) and Moglen Ravicher LLC
| 1995 Broadway, 17th Fl., New York, NY 10023
| (212) 461-1902 direct  (212) 580-0800 main  (212) 580-0898 fax
| ravicher@softwarefreedom.org   www.softwarefreedom.org

[1] http://spdx.org/
[2] http://spdx.org/licenses/

Signed-off-by: Wolfgang Denk <wd@denx.de>
11 years agoPrepare v2013.07 v2013.07
Tom Rini [Mon, 22 Jul 2013 19:57:32 +0000 (15:57 -0400)]
Prepare v2013.07

Signed-off-by: Tom Rini <trini@ti.com>
11 years agofs/ext4: fix log2blksz un-initialized error, by cacaulating its value from blksz
Lan Yixun (dlan) [Sat, 20 Jul 2013 00:17:59 +0000 (08:17 +0800)]
fs/ext4: fix log2blksz un-initialized error, by cacaulating its value from blksz

The problem here is that uboot can't mount ext4 filesystem with
commit "50ce4c07df1" applied. We use hard-coded "SECTOR_SIZE"(512)
before this commit, now we introduce (block_dev_desc_t *)->log2blksz
to replace this macro. And after we calling do_ls()->fs_set_blk_dev(),
the variable log2blksz is not initialized, which it's not correct.

And this patch try to solve the problem by caculating the value of
log2blksz from variable blksz.

11 years agoext4fs: le32_to_cpu() used on a 16-bit field
Rommel Custodio [Sun, 21 Jul 2013 08:53:25 +0000 (10:53 +0200)]
ext4fs: le32_to_cpu() used on a 16-bit field

Fix reading ext4_extent_header struture on BE machines.  Some 16 bit
fields where converted to 32 bit fields, due to the byte swap on BE
machines the containing value was corrupted. Therefore reading ext4
filesystems on BE machines where broken before.

Signed-off-by: Rommel Custodio <sessyargc+uboot@gmail.com>
[sent via git-send-email; rework commit message]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
11 years agoarm: at91sam9n12: change EBI IO to high drive mode
Bo Shen [Wed, 17 Jul 2013 09:14:17 +0000 (17:14 +0800)]
arm: at91sam9n12: change EBI IO to high drive mode

As both the DDR SDRAM and NAND flash connect to EBI on at91sam9n12
and share the lower 8 bits data line. If use low drive of the data
line, it will cause DDR data access corrupt in lower address, so
change the data line to high drive mode

This will fix the Linux kernel boot issue when use Lower address

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
11 years agoddr cfg: DRAM_RESET needs 0x00020030
Troy Kisky [Wed, 17 Jul 2013 19:46:15 +0000 (12:46 -0700)]
ddr cfg: DRAM_RESET needs 0x00020030

The old value of 0x000e0030 will cause ethernet
timeout issues on the sabrelite and possibly other
boards using the KSZ9021.
I have no explanation as to why.

But this is a correct change, the TRM will be updated
to show that 00b is the only valid setting for bits
19-18 of DRAM_RESET.

My thanks go to Liu Hui(Jason) for this information.

Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
11 years agonet: phy: Set SUPPORTED_1000baseX_Half flag in ESTATUS_1000_XHALF case
Fabio Estevam [Fri, 19 Jul 2013 13:01:34 +0000 (10:01 -0300)]
net: phy: Set SUPPORTED_1000baseX_Half flag in ESTATUS_1000_XHALF case

Commit de1d786e (add support for Xilinx 1000BASE-X phy (GTX)) introduced the
checking for ESTATUS_1000_XHALF, but it incorrectly sets the
SUPPORTED_1000baseX_Full flag in this case.

Set the SUPPORTED_1000baseX_Half flag instead.

Acked-by: Charles Coldwell <coldwell@gmail.com>
Reviewed-By: Sascha Silbe <t-uboot@infra-silbe.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
11 years agophy: fix 10/100Mbps operation on 1Gbps-capable links
Sascha Silbe [Fri, 19 Jul 2013 10:25:10 +0000 (12:25 +0200)]
phy: fix 10/100Mbps operation on 1Gbps-capable links

de1d786 [add support for Xilinx 1000BASE-X phy (GTX)] introduced a
check for the extended status register in order to support
1Gbps-capable PHYs that don't have the 1000BASE-T registers. Since
Extended Status only indicates what the PHY (i.e. the local side) is
capable of, this broke communication with non-1Gbps peers.

Only check the extended status if the 1000BASE-T registers are
actually missing so we don't end up setting speed to 1Gbps even though
the previous test (for the combination of local and peer support for
1Gbps) already indicated we can't do 1Gbps with the current peer.

Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
11 years agomkimage: Use board config to get CONFIG_FIT_SIGNATURE value
Simon Glass [Wed, 17 Jul 2013 22:10:59 +0000 (15:10 -0700)]
mkimage: Use board config to get CONFIG_FIT_SIGNATURE value

The value of this config variable is not available to image.h on the host,
since the board config is not actually included. Bring this in so that
mkimage will be built with image-signing support for sandbox at least.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agoarm:trats:fix: Correction of loaddtb environment variable.
Łukasz Majewski [Thu, 18 Jul 2013 11:14:22 +0000 (13:14 +0200)]
arm:trats:fix: Correction of loaddtb environment variable.

Missing space for loaddtb command has been added. When missing, ext4load
fails with wrong number of passed parameters.

Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
11 years agobootm: Move fixup_silent_linux() earlier in the bootm stages
Simon Glass [Wed, 17 Jul 2013 03:09:59 +0000 (20:09 -0700)]
bootm: Move fixup_silent_linux() earlier in the bootm stages

Before the bootm refactor, fixup_silent_linux() was done only in the
monolithic bootm case, not in the subcommand case. With the refactor, it
is done always, which is good. Unfortunately it is done too late, since it
is the PREP or CMDLINE stages that set up the command line for Linux.

Move fixup_silent_linux() into the LOADOS stage, which is where we find
out the OS being used, and can thus decide whether to perform this step.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agoREADME.mx28_common: Rename it to README.mxs
Fabio Estevam [Fri, 12 Jul 2013 11:31:05 +0000 (08:31 -0300)]
README.mx28_common: Rename it to README.mxs

commit 54965b61360 (README: mxs: Introduce README.mxs) should have changed the
file name to README.mxs, as it covers both mx23 and mx28 now.

Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
11 years agoMerge branch 'master' of git://git.denx.de/u-boot-mmc
Tom Rini [Wed, 17 Jul 2013 01:05:35 +0000 (21:05 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc

11 years agofsl_esdhc: Touch only relevant sys ctrl bits
Dirk Behme [Mon, 15 Jul 2013 13:44:29 +0000 (15:44 +0200)]
fsl_esdhc: Touch only relevant sys ctrl bits

Dealing with the sys ctrl register should touch only the
relevant bits and not accidently the whole register. On i.MX6,
the sys control register contains bits which shouldn't be reset to
0, e.g. SYS_CTRL[3-0] and IPP_RST_N (SYS_CTRL[23]).

Do this by read/modify/write instead of just a 32bit write.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agodrivers/mmc/dw_mmc - remove extra arch specific "asm/arch/clk.h" inclusion
Alexey Brodkin [Mon, 15 Jul 2013 11:30:30 +0000 (15:30 +0400)]
drivers/mmc/dw_mmc - remove extra arch specific "asm/arch/clk.h" inclusion

1. No contents of "asm/arch/clk.h" is used within "dw_mmc.c".
2. If arch doesn't have "asm/arch/clk.h" driver won't build.

Without mentioned inclusion dw_mmc driver could be built for arches
other than ARM. For ARM driver still builds without it.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agoPowerpc: eSDHC: Fix mmc read write err in uboot of T4240QDS board
Haijun.Zhang [Mon, 1 Jul 2013 06:26:01 +0000 (14:26 +0800)]
Powerpc: eSDHC: Fix mmc read write err in uboot of T4240QDS board

Fill the right command type when using CMD12 to stop data transfer.

Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
CC: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agopowerpc/mpc85xx:Disable Debug TLB entry for non-minimal SPL
Prabhakar Kushwaha [Fri, 5 Jul 2013 06:29:26 +0000 (11:59 +0530)]
powerpc/mpc85xx:Disable Debug TLB entry for non-minimal SPL

CONFIG_SPL_BUILD creates debug TLB entry, so disable it before init_tlbs.

CONFIG_SPL_INIT_MINIMAL never creates any debug TLB entry, so no need
of disable_tlb().

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agompc85xx: Add gdsys ControlCenter Digital board
Dirk Eibach [Wed, 26 Jun 2013 13:55:17 +0000 (15:55 +0200)]
mpc85xx: Add gdsys ControlCenter Digital board

The gdsys ControlCenter Digital board is based on a Freescale P1022 QorIQ SOC.
It boots from SPI-Flash but can be configured to boot from SD-card for
factory programming and testing.
On board peripherals include:
- 2x GbE
- Lattice ECP3 FPGA connected via PCIe
- mSATA RAID1
- USB host
- DisplayPort video output
- Atmel TPM

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agoBuild arch/$ARCH/lib/bootm.o depending on CONFIG_CMD_BOOTM
Dirk Eibach [Wed, 26 Jun 2013 13:55:16 +0000 (15:55 +0200)]
Build arch/$ARCH/lib/bootm.o depending on CONFIG_CMD_BOOTM

MAKEALL is fine for ppc4xx and mpc85xx.
Run checks were done on our controlcenterd hardware.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agoAdd Atmel I2C tpm
Dirk Eibach [Wed, 26 Jun 2013 13:55:15 +0000 (15:55 +0200)]
Add Atmel I2C tpm

Add support for Atmel TPM devices with two wire interface.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agoi2c: fsl_i2c: i2c_read(): dont try to write address w/ alen=0
Reinhard Pfau [Wed, 26 Jun 2013 13:55:14 +0000 (15:55 +0200)]
i2c: fsl_i2c: i2c_read(): dont try to write address w/ alen=0

if alen is 0: no longer start a write cycle before reading data.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agotpm: add AUTH1 cmds for LoadKey2 and GetPubKey
Reinhard Pfau [Wed, 26 Jun 2013 13:55:13 +0000 (15:55 +0200)]
tpm: add AUTH1 cmds for LoadKey2 and GetPubKey

Extend the tpm library with support for single authorized (AUTH1) commands
as specified in the TCG Main Specification 1.2. (The internally used helper
functions are implemented in a way that they could also be used for double
authorized commands if someone needs it.)

Provide enums with the return codes from the TCG Main specification.

For now only a single OIAP session is supported.

OIAP authorized version of the commands TPM_LoadKey2 and TPM_GetPubKey are
provided. Both features are available using the 'tpm' command, too.

Authorized commands are enabled with CONFIG_TPM_AUTH_SESSIONS. (Note that
this also requires CONFIG_SHA1 to be enabled.)

Signed-off-by: Reinhard Pfau <reinhard.pfau@gdsys.cc>
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
11 years agoarm:samsung:trats:fix: Restore proper orientation of TRATS's LCD panel
Łukasz Majewski [Mon, 15 Jul 2013 14:09:50 +0000 (16:09 +0200)]
arm:samsung:trats:fix: Restore proper orientation of TRATS's LCD panel

Before setting: mipi_lcd_device.reverse_panel = 1, the Trats's LCD panel
was flipped by 180 degrees.

The flip was caused by following change:
Exynos: Change get_timer() to work correctly
SHA1: 3d00c0cb96ff93a929700b80d89cb905e5ab5315

This commit fixed udelay(), which is necessary (due to HW LCD controller
oddity) for mipi-dsi correct operation. As a result the display orientation
has been switched.

As a follow up, the hwrevision() function has been removed, since it was
used only in this particular place.

Test HW: Trats Exynos4210 rev 0.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
11 years agoarm:exynos:fix: Fix clock calculation for Exynos4210 based targets.
Łukasz Majewski [Fri, 12 Jul 2013 17:08:25 +0000 (19:08 +0200)]
arm:exynos:fix: Fix clock calculation for Exynos4210 based targets.

Provide proper setting for the APLL fout frequency calculation for
Exynos4 based targets (especially Exynos4210 - Trats board).

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
11 years agoPPC MPC83xx: Fix MPC8323ERDB build warning
Wolfgang Denk [Sun, 14 Jul 2013 17:42:40 +0000 (19:42 +0200)]
PPC MPC83xx: Fix MPC8323ERDB build warning

Fix:

mpc8323erdb.c: In function 'mac_read_from_eeprom':
mpc8323erdb.c:198:3: warning: dereferencing type-punned pointer will
break strict-aliasing rules [-Wstrict-aliasing]

Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Timur Tabi <timur@tabi.org>
cc: Kim Phillips <kim.phillips@freescale.com>

11 years agoFix ext2/ext4 filesystem accesses beyond 2TiB
Frederic Leroy [Wed, 26 Jun 2013 16:11:25 +0000 (18:11 +0200)]
Fix ext2/ext4 filesystem accesses beyond 2TiB

With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives

We now use lbaint_t for partition offset to reflect the lbaint_t change,
and access partitions beyond or crossing the 2.1TiB limit.
This required changes to signature of ext4fs_devread(), and type of all
variables relatives to block sector.

ext2/ext4 fs uses logical block represented by a 32 bit value. Logical
block is a multiple of device block sector. To avoid overflow problem
when calling ext4fs_devread(), we need to cast the sector parameter.

Signed-off-by: Frédéric Leroy <fredo@starox.org>
11 years agocommon: remove unaligned access error in bootmenu_getoption()
Lan Yixun (dlan) [Thu, 27 Jun 2013 10:58:53 +0000 (18:58 +0800)]
common: remove unaligned access error in bootmenu_getoption()

Some ARM compilers may emit code that makes unaligned accesses when
faced with constructs such as:

    char name[12] = "bootmenu_";

same fix as commit: 064d55f8bc8d7d205ed0be6abb6717e92eeb7cad

=========================================================
data abort

    MAYBE you should read doc/README.arm-unaligned-accesses

pc : [<3ff4b60c>]          lr : [<3ff4b7b0>]
sp : 3f346a58  ip : 3ff9c8e6     fp : 02000060
r10: 00000000  r9 : 3df47fc0     r8 : 3f347f40
r7 : 00000000  r6 : 00000000     r5 : 00000003  r4 : 3f759140
r3 : 000003f0  r2 : 00000000     r1 : 000003f1  r0 : 00000000
Flags: nzCv  IRQs on  FIQs off  Mode SVC_32
Resetting CPU ...
======================================================

Signed-off-by: Lan Yixun (dlan) <dennis.yxun@gmail.com>
11 years agocramfs: fix bug for wrong filename comparison
Holger Brunck [Mon, 8 Jul 2013 07:06:49 +0000 (09:06 +0200)]
cramfs: fix bug for wrong filename comparison

"cramfsload uImage_1" succeeds even though the actual file is named
"uImage".

Fix file name comparison when one name is the prefix of the other.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

11 years agopatman: README documentation nits (unit test)
Gerhard Sittig [Sun, 14 Jul 2013 09:27:45 +0000 (11:27 +0200)]
patman: README documentation nits (unit test)

adjust instructions for the invocation of Patman's self test: the -t
flag appears to have a different meaning now, refer to the --test option
for the builtin unit test; adjust a directory location and make sure to
run the file which resides in the source directory

Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
11 years agoscsi: Correct types of scsi_read/write()
Simon Glass [Wed, 3 Jul 2013 14:11:41 +0000 (07:11 -0700)]
scsi: Correct types of scsi_read/write()

The block device expects to see lbaint_t for the blknr parameter. Change
the SCSI read/write functions to suit.

This fixes the following build warnings for coreboot:

cmd_scsi.c: In function ‘scsi_scan’:
cmd_scsi.c:119:30: error: assignment from incompatible pointer type [-Werror]
cmd_scsi.c:120:32: error: assignment from incompatible pointer type [-Werror]

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agoRevert "MIPS: Jz4740: Add qi_lb60 board support"
Tom Rini [Mon, 15 Jul 2013 13:19:39 +0000 (09:19 -0400)]
Revert "MIPS: Jz4740: Add qi_lb60 board support"

The files board/qi/qi_lb60/qi_lb60.c and include/configs/qi_lb60.h were
licensed under the GPL v3 or later, and not v2 or later.  As this is
incompatible with the project, revert this board support until the
responsible parties are available to re-license (if so desired) under
GPL v2.

Signed-off-by: Tom Rini <trini@ti.com>
11 years agoPrepare v2013.07-rc3 v2013.07-rc3
Tom Rini [Fri, 12 Jul 2013 21:16:19 +0000 (17:16 -0400)]
Prepare v2013.07-rc3

Signed-off-by: Tom Rini <trini@ti.com>
11 years agoMerge branch 'master' of git://git.denx.de/u-boot-nand-flash
Tom Rini [Fri, 12 Jul 2013 21:18:59 +0000 (17:18 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash

11 years agobootm: Handle errors consistently
Simon Glass [Wed, 10 Jul 2013 13:25:33 +0000 (09:25 -0400)]
bootm: Handle errors consistently

A recent bootm fix left the error path incomplete. If CONFIG_TRACE is
set it may still not be a supported command, so cover that with the
unsupported subcommand print.  Once we handle BOOTM_STATE_OS_GO, we can
just move into the error handler itself, no need for a goto there.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Update slightly based on Simon's changes to also cover
CONFIG_TRACE/BOOTM_STATE_FAKE_OS_GO]
Signed-off-by: Tom Rini <trini@ti.com>
11 years agomtd: mxc_nand: Fix crash after MTD resync
Marek Vasut [Wed, 3 Jul 2013 00:34:34 +0000 (02:34 +0200)]
mtd: mxc_nand: Fix crash after MTD resync

The driver triggered a BUG() in nand_base.c:3214/nand_scan_tail()
because the ecc.strength was not set in NAND_ECC_HW_SYNDROME ECC
mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
11 years agocommon/image.c: Fix regression with ramdisk load/entry points in FIT
Stefano Babic [Fri, 12 Jul 2013 13:09:23 +0000 (15:09 +0200)]
common/image.c: Fix regression with ramdisk load/entry points in FIT

A FIT image with a ramdisk that sets the entry or load points to 0x0
must be treated as meaning "leave in place" and NOT "relocate to 0x0".
This regression was introduced in a51ec63.

Signed-off-by: Stefano Babic <sbabic@denx.de>
11 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Fri, 12 Jul 2013 14:36:48 +0000 (10:36 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.

Conflicts:
arch/arm/dts/exynos5250.dtsi

Signed-off-by: Tom Rini <trini@ti.com>
11 years agobootm: Correct the arguments for the ELF image loader
Simon Glass [Thu, 11 Jul 2013 06:08:11 +0000 (23:08 -0700)]
bootm: Correct the arguments for the ELF image loader

The arguments were out of place since commit 983c72f, since this file was
missed and not tested. Correct this.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agobootm: Use selected configuration for ramdisk and fdt
Simon Glass [Thu, 11 Jul 2013 06:08:10 +0000 (23:08 -0700)]
bootm: Use selected configuration for ramdisk and fdt

If a specific configuraion is selected by the bootm command, e.g. with
'bootm 84000000#recoveryconf' we must honour this for not just the kernel,
but also the ramdisk and FDT.

In the conversion to using a common fit_image_load() function for loading
images from FITs (commits a51ec63 and 53f375f) this feature was lost.
Reinstate it by passing the selected configuration back from
fit_image_load() to boot_get_kernel(), then use this configuration
(which is stored in images->fit_uname_cfg) in both boot_get_ramdisk()
and boot_get_fdt().

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agoblackfin: x86: bootm: Handle PREP stage of bootm
Simon Glass [Thu, 11 Jul 2013 06:08:09 +0000 (23:08 -0700)]
blackfin: x86: bootm: Handle PREP stage of bootm

The OS function is now always called with the PREP stage. Adjust the
remaining bootm OS functions to deal with this correctly.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agobootm: Remove extra OK message
Simon Glass [Thu, 11 Jul 2013 06:08:08 +0000 (23:08 -0700)]
bootm: Remove extra OK message

This is not needed as we already print 'OK' later in all cases.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agocmd_bootm.c: Re-order bootm_load_os return check for ELDK4.2
Tom Rini [Thu, 11 Jul 2013 13:35:23 +0000 (09:35 -0400)]
cmd_bootm.c: Re-order bootm_load_os return check for ELDK4.2

With ELDK4.2 we were getting a warning that load_end may be used
uninitialized in calling lmb_reserve.  This could not be the case,
however.  If we re-order the checks (and make them slightly clearer as
well) the warning goes away.  bootm_load_os may only return 0 on
success, BOOTM_ERR_OVERLAP in a non-fatal overlap (already covered in
comments) or a fatal BOOTM_ERR that is covered in the error handler.

Signed-off-by: Tom Rini <trini@ti.com>
11 years agoMerge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Albert ARIBAUD [Fri, 12 Jul 2013 11:20:35 +0000 (13:20 +0200)]
Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

11 years agomx53ard: Change default environment to cope with OE changes
Otavio Salvador [Fri, 28 Jun 2013 21:52:44 +0000 (18:52 -0300)]
mx53ard: Change default environment to cope with OE changes

OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
11 years agomx51evk: Change default environment to cope with OE changes
Otavio Salvador [Fri, 28 Jun 2013 21:52:43 +0000 (18:52 -0300)]
mx51evk: Change default environment to cope with OE changes

OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
11 years agowandboard: Change default environment to cope with OE changes
Otavio Salvador [Fri, 28 Jun 2013 21:52:42 +0000 (18:52 -0300)]
wandboard: Change default environment to cope with OE changes

OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
11 years agomx6slevk: Change default environment to cope with OE changes
Otavio Salvador [Fri, 28 Jun 2013 21:52:41 +0000 (18:52 -0300)]
mx6slevk: Change default environment to cope with OE changes

OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
11 years agomx6qsabrelite: Change default environment to cope with OE changes
Otavio Salvador [Fri, 28 Jun 2013 21:52:40 +0000 (18:52 -0300)]
mx6qsabrelite: Change default environment to cope with OE changes

OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
11 years agomx53loco: Change default environment to cope with OE changes
Otavio Salvador [Fri, 28 Jun 2013 21:52:39 +0000 (18:52 -0300)]
mx53loco: Change default environment to cope with OE changes

OpenEmbedded has change partitioning layout of generated image so it
does not raise warnings during the boot regarding unkown partition
being used for U-Boot.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Jason Liu <r64343@freescale.com>
11 years agonet: fec: Avoid MX28 bus sync issue
Marek Vasut [Thu, 11 Jul 2013 23:03:04 +0000 (01:03 +0200)]
net: fec: Avoid MX28 bus sync issue

The MX28 multi-layer AHB bus can be too slow and trigger the
FEC DMA too early, before all the data hit the DRAM. This patch
ensures the data are written in the RAM before the DMA starts.
Please see the comment in the patch for full details.

This patch was produced with an amazing help from Albert Aribaud,
who pointed out it can possibly be such a bus synchronisation
issue.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
11 years agonet: fec: Remove bogus flush_dcache_range() call
Marek Vasut [Thu, 11 Jul 2013 15:23:26 +0000 (17:23 +0200)]
net: fec: Remove bogus flush_dcache_range() call

Remove incorrectly called and duplicate flush_dcache_range() call
from fec_mxc driver. The call is not needed, since the caches are
already flushed in fec_tbd_init(), moreover the second argument should
be the ending address, not size.

Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
11 years agom28evk: add trimffs to nand command
Marek Vasut [Sun, 7 Jul 2013 18:20:26 +0000 (20:20 +0200)]
m28evk: add trimffs to nand command

this is usefull when writing an UBI image which contains
and UBIFS volume (check README.nand and UBI FAQ for more
details)

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
11 years agoARM: tegra: enable LCD panel on Ventana
Stephen Warren [Tue, 18 Jun 2013 15:46:52 +0000 (09:46 -0600)]
ARM: tegra: enable LCD panel on Ventana

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
11 years agoARM: tegra: enable LCD panel on Harmony
Stephen Warren [Tue, 18 Jun 2013 15:46:51 +0000 (09:46 -0600)]
ARM: tegra: enable LCD panel on Harmony

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
11 years agoTegra: Config: Enable Tegra30/Tegra114 USB function
Jim Lin [Fri, 21 Jun 2013 11:05:48 +0000 (19:05 +0800)]
Tegra: Config: Enable Tegra30/Tegra114 USB function

Add USB EHCI, storage and network support.

Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
11 years agoARM: Tegra: USB: EHCI: Add support for Tegra30/Tegra114
Jim Lin [Fri, 21 Jun 2013 11:05:47 +0000 (19:05 +0800)]
ARM: Tegra: USB: EHCI: Add support for Tegra30/Tegra114

Tegra30 and Tegra114 are compatible except PLL parameters.

Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
11 years agoARM: Tegra: FDT: Add USB EHCI function for T30/T114
Jim Lin [Fri, 21 Jun 2013 11:05:46 +0000 (19:05 +0800)]
ARM: Tegra: FDT: Add USB EHCI function for T30/T114

Add DT node for USB EHCI function.
Add support for T30-Cardhu, T30-Beaver, T114-Dalmore boards.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
11 years agoMerge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Albert ARIBAUD [Wed, 10 Jul 2013 18:40:47 +0000 (20:40 +0200)]
Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'

11 years agousb: pxa27x_udc: fix compiler warnings
Mike Dunn [Wed, 26 Jun 2013 19:33:54 +0000 (12:33 -0700)]
usb: pxa27x_udc: fix compiler warnings

Newer gcc versions warn about unused variables.  This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
11 years agodfu: Update DFU's authorship history
Łukasz Majewski [Fri, 5 Jul 2013 09:40:47 +0000 (11:40 +0200)]
dfu: Update DFU's authorship history

The DFU's state machine original implementation author and copyright were
missing.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
11 years agocmd_bootm.c: Make bootz handle BOOTM_STATE_FINDOTHER itself
Tom Rini [Tue, 9 Jul 2013 19:33:25 +0000 (15:33 -0400)]
cmd_bootm.c: Make bootz handle BOOTM_STATE_FINDOTHER itself

As a zImage does not have a U-Boot header, we cannot really do what
BOOTM_STATE_FINDOTHER does, exactly.  Break the ramdisk/fdt portions of
bootm_find_other into bootm_find_ramdisk/fdt which can be called in both
cases.

Signed-off-by: Tom Rini <trini@ti.com>
11 years agocmd_bootm.c: Make bootz consume 'bootz' from argv, decrement argc
Tom Rini [Tue, 9 Jul 2013 19:32:34 +0000 (15:32 -0400)]
cmd_bootm.c: Make bootz consume 'bootz' from argv, decrement argc

Like 'bootm', 'bootz' needs to consume 'bootz' so that the rest of the
state functions will work.

Signed-off-by: Tom Rini <trini@ti.com>
11 years agobootm: Add the missing PREP stage to bootz and correct image handling
Simon Glass [Thu, 4 Jul 2013 20:26:11 +0000 (13:26 -0700)]
bootm: Add the missing PREP stage to bootz and correct image handling

In the recent bootm refactor, the PREP stage was missing in the bootz
command. This causes unpredictable behaviour.

The use of a local variable means that the reset of cmd_bootm.c does not
in fact use the same image structure, so remove this.

Also manually set the OS type to Linux, since this is the only possibility
at present, and we need to select the right boot function.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agobootm: Clean up bootz_setup() function
Simon Glass [Thu, 4 Jul 2013 20:26:10 +0000 (13:26 -0700)]
bootm: Clean up bootz_setup() function

This function has no prototype in the headers and passes void * around, thus
requiring several casts. Tidy this up.

- Add new patch to clean up bootz_setup() function

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agobootm: Require boot function only if it is about to be used
Simon Glass [Thu, 4 Jul 2013 20:26:09 +0000 (13:26 -0700)]
bootm: Require boot function only if it is about to be used

The original bootm code (before commit 35fc84f) did not check for a valid
boot function in the subcommand case, which was incorrect.

This check was introduced in all cases, but in fact we should only check
for the function when we need it. Otherwise in some cases the check fires
before the OS type is known.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agobootm: Disable interrupts only when loading
Simon Glass [Thu, 4 Jul 2013 20:26:08 +0000 (13:26 -0700)]
bootm: Disable interrupts only when loading

With the move of the interrupt code to earlier in the sequence, we
exposed a problem where the interrupts are disabled at each bootm
stage. This is not correct - it should be done only once. Let's disable
interrupts in the LOAD stage. Put the code in a function for clarity.

Also, bootz lost its interrupt code altogether, so reinstate it.

Signed-off-by: Simon Glass <sjg@chromium.org>
11 years agoMerge branch 'master' of git://git.denx.de/u-boot-video
Tom Rini [Wed, 10 Jul 2013 12:42:25 +0000 (08:42 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-video

11 years agoEXYNOS: Resolve the i2c compilation error
Amar [Wed, 10 Jul 2013 05:12:29 +0000 (10:42 +0530)]
EXYNOS: Resolve the i2c compilation error

This patch resolves the below mentioned compilation error of i2c driver
for non-FDT case

Compilation error:
s3c24x0_i2c.c: In function 'board_i2c_init':
s3c24x0_i2c.c:544:18: error: 'CONFIG_MAX_I2C_NUM' undeclared (first use
in this function) s3c24x0_i2c.c:544:18: note: each undeclared
identifier is reported only once for each function it appears in
s3c24x0_i2c.c:545:3: warning: implicit declaration of function

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
11 years agoarm: exynos: fix clock calculation
Minkyu Kang [Fri, 5 Jul 2013 10:08:33 +0000 (19:08 +0900)]
arm: exynos: fix clock calculation

There are differnce with clock calcuation by cpu variations.
This patch will fix it according to user manual.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
11 years agovideo: consolidate splash screen alignment code
Anatolij Gustschin [Mon, 1 Jul 2013 22:04:05 +0000 (00:04 +0200)]
video: consolidate splash screen alignment code

Code for checking "splashpos" environment variable is
duplicated in drivers, move it to the common function.
Call this function also in the bmp display command to
consider "splashpos" settings.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
11 years agopower:bat:trats: Break battery charging with ctrl+C
Łukasz Majewski [Tue, 25 Jun 2013 13:28:15 +0000 (15:28 +0200)]
power:bat:trats: Break battery charging with ctrl+C

Add support for disabling battery charging with ctrl+C keyboard
combination pressed.
Moreover the battery update is done more frequently.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
11 years agoarm:trats: Increase malloc pool size (for DFU ext4 transfers)
Łukasz Majewski [Fri, 28 Jun 2013 16:43:53 +0000 (18:43 +0200)]
arm:trats: Increase malloc pool size (for DFU ext4 transfers)

Commit:
dfu: make data buffer size configurable
SHA1: 89a72b2e0e141042c9109185e02d39b2107ffc62

replaced statically allocated buffers with one allocated with memalign.

Malloc pool size of 1MiB was too small, since we needed bigger buffer to
transfer for example uImage.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
11 years agoEXYNOS: Move files from board/samsung to arch/arm
Rajeshwari Shinde [Thu, 4 Jul 2013 06:59:17 +0000 (12:29 +0530)]
EXYNOS: Move files from board/samsung to arch/arm

This patch performs the following:

1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
   the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
   done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.

TEST: Tested SD-MMC boot on SMDK5250 and Origen.
      Tested USB and SPI boot on SMDK5250
      Compile tested for SMDKV310.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
11 years agoEXYNOS4210: Configure GPIO for uart
Rajeshwari Shinde [Thu, 4 Jul 2013 06:59:16 +0000 (12:29 +0530)]
EXYNOS4210: Configure GPIO for uart

This patch configures the gpio values for UART
on Origen and SMDKV310 using pinmux

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>