ARM: da850evm_direct_nor: Enable DM_GPIO

The SPI and NAND variants enable DM_GPIO, so this patch enables
DM_GPIO for the NOR / XIP version of the da850-evm.

Signed-off-by: Adam Ford <aford173@gmail.com>

ARM: da850evm_nand: Enable Ethernet

The NAND configuration has had the ethernet missing, so this patch
enables the on-board ethernet interface.

Signed-off-by: Adam Ford <aford173@gmail.com>

Kconfig: Varios: Fix more SPL, TPL dependencies

Several options are presenting themselves on a various boards
where the options are clearly not used.  (ie, SPL/TPL options
when SPL or TPL are not defined)

This patch is not attempting to be a complete list of items, but
more like low hanging fruit.  In some instances, I wasn't sure
of DM was required, so I simply made them SPL or TPL.

This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.

Signed-off-by: Adam Ford <aford173@gmail.com>

MAINTAINERS,board/siemens: update maintainer

Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>

mailmap: Update mail address

Update my email address from gmail to my domain.

Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>

board: ti: am43xx_evm_usbboot: Enable DM for USB, fix SPL build errors

To address the following warning message:

===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================

CONFIG_DM_USB is enabled, this resulted in SPL build errors:

drivers/built-in.o: In function 'xhci_dwc3_probe':
u-boot/drivers/usb/host/xhci-dwc3.c:155: undefined reference to 'usb_get_dr_mode'
scripts/Makefile.spl:404: recipe for target 'spl/u-boot-spl' failed
make[1]: *** [spl/u-boot-spl] Error 1
Makefile:1721: recipe for target 'spl/u-boot-spl' failed
make: *** [spl/u-boot-spl] Error 2

Enabling usb common library and usb ethernet drivers in SPL
does the job. Target was compile tested, build was clean.

Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>

nvme: Fix PRP Offset Invalid

When large writes take place I saw a Samsung EVO 970+ return a status
value of 0x13, PRP Offset Invalid.  I tracked this down to the
improper handling of PRP entries.  The blocks the PRP entries are
placed in cannot cross a page boundary and thus should be allocated
on page boundaries.  This is how the Linux kernel driver works.

With this patch, the PRP pool is allocated on a page boundary and
other than the very first allocation, the pool size is a multiple of
the page size.  Each page can hold (4096 / 8) - 1 entries since the
last entry must point to the next page in the pool.

Signed-off-by: Aaron Williams <awilliams@marvell.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

cmd: pci: Adjust display of digits for 64bit address and size

The command "pci bar" and "pci region" display the address and size in
16 characters including "0x", so the command can only display
14 hexadecimal digits if the number of digits in the address and size is
less than 14.

    ID   Base                Size                Width  Type
    ----------------------------------------------------------
     0   0x00000020000000  0x00000000100000  64     MEM   Prefetchable
     1   0xffff000080000000  0x00000000100000  64     MEM   Prefetchable

The 64-bit address and size should be displayed in 18(= 16+2) digits,
so this patch adjusts them.

Cc: Yehuda Yitschak <yehuday@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

ARM: omap3_logic: Fix SPL boot failure when EHCI enabled

Some of the USB code is still being built into SPL even when the
SPL menu options have it explicitly disabled for SPL. Unit there is
a better solution, This patch undefines CONFIG_USB_EHCI_OMAP when
building SPL which reduces the code and lets the board boot again.

Fixes: 25e4ff45b17d ("ARM: omap3_logic: Enable OMAP EHCI support
for SOM-LV Boards")

Signed-off-by: Adam Ford <aford173@gmail.com>

cmd: gpio: remove redundant assignment

The assigned value NULL is overwritten before being used. Remove the
assignment.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

vexpress/aemv8a: drop CONFIG_ARMV8_SWITCH_TO_EL1

To support KVM, we need to drop at EL2 and not EL1 before we boot Linux
kernel. This causes issues on platform with VHE and secondaries booting
at EL2 via TF-A PSCI CPU_ON call.

Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

ARM: vexpress_*_defconfig: replace earlyprintk with earlycon

earlyprintk no longer works on arm64 platforms. Replace it with earlycon
which works fine.

Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

fat: FAT filesystem premature release of info struct.

File was found on specified location. Info about file was read,
but then immediately destroyed using 'free' call. As a result
file size was set to 0, hence fat process didn't read any data.

Premature 'free' call removed. Resources are freed right before
function return. File is read correctly.

Signed-off-by: Martin Vystrcil <martin.vystrcil@m-linux.cz>

dm: scsi: Scan the actual number of ports

The scsi_scan_dev() is looping over the number of uc_plat->max_id.
The number of actual ports a AHCI controller has can be greater than
max_id. Update uc_plat->max_id to make SCSI scan all detected ports.

Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux

When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node  when it should have been placed into the
omap3_pmx_core.  This error was accidentally propagated to U-Boot by
me when I blindly copied the device tree from Linux.

This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.

Signed-off-by: Adam Ford <aford173@gmail.com>

board_f: reserve noncached space below malloc area

Noncached area at present is being initialized to random space after malloc
area. It works in most the cases as it goes to stack area & stack is not
overwriting it being far from it.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>

arm: ti: Fix regression in distro boot for mmc

When devnum was changed to a local variable in distro_bootcmd we ran
into a problem on TI platforms (confirmed on Beaglebone) as we had been
using 'setenv devnum' there as well and it needs to match the other
usage.

Fixes: 13dd6665ed18 ("distro: not taint environment variables if possible")
[trini: Review other platforms, re-word commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch '2019-08-24-master-imports'

- Migrate SYS_SPI_U_BOOT_OFFS, SYS_NAND_USE_FLASH_BBT and ARCH_CPU_INIT
  to Kconfig

Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig

This converts the following to Kconfig:
   CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>

moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 4

the x530 board needs conversion of SPL_SPI_LOAD to Kconfig first

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>

moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 3

Exact two boards are referencing CONFIG_SYS_SPI_U_BOOT_OFFS to another
define, we replace this manually with the value for having a clean run
of moveconfig.py afterwards.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 2

some boards have common headers for several individual build-targets
where CONFIG_SYS_SPI_U_BOOT_OFFS is defined even it is not needed (only
needed if CONFIG_SPL_SPI_LOAD is defined also). Take this define here
under '#ifdef CONFIG_SPL_SPI_LOAD' for having a clean run of
moveconfig.py

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

moveconfig: prepare moving CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig step 1

Some boards have coded this offset with formula or bitshifts in their
board-config. Manually convert these things into hex-values to be able
using moveconfig.py afterwards.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

mtd: nand: raw: Move CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig

Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.

Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_ARCH_CPU_INIT to Kconfig

This converts the following to Kconfig:
   CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge tag 'u-boot-rockchip-20190823' of https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip

- remove rk3288 fennec board
- remove SPL raw image support for Rockchip SoCs
- add common misc_init_r() for ethaddr from cpuid
- enable USB HOST support for rk3328
- unify code for finding a valid gpt in part driver

Merge branch '2019-08-23-master-imports'

- Migrate CONFIG_MX_CYCLIC, CONFIG_FSL_USDHC and CONFIG_MXS_GPIO to
  Kconfig
- Fix some SPL/TPL and ARM64 dependencies

Convert CONFIG_MX_CYCLIC to Kconfig

This converts the following to Kconfig:
   CONFIG_MX_CYCLIC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: David Lechner <david@lechnology.com>

Convert CONFIG_FSL_USDHC to Kconfig

This converts the following to Kconfig:
   CONFIG_FSL_USDHC

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>

Kconfigs: Various: Fix some SPL, TPL and ARM64 dependencies

Several options are presenting themselves on a various boards
where the options are clearly not used.  (ie, arm64 options on
arm9, or SPL/TPL options when SPL or TPL are not defined)

This patch is not attempting to be a complete list of items, but
more like low hanging fruit.

This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.

Signed-off-by: Adam Ford <aford173@gmail.com>

kconfig: Convert CONFIG_MXS_GPIO to Kconfig

This converts the following to Kconfig:
   CONFIG_MXS_GPIO

Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/571260789

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>

Merge https://gitlab.denx.de/u-boot/custodians/u-boot-clk

evb_rk3399: revert CONFIG_SYS_MMC_ENV_DEV to 0

This was changed to 1 in commit 0717dde057e, but a few months later,
commit 5f9411af37b swapped the order of eMMC and SD card by assigning
indexed aliases to `&sdhci` and `&sdmmc`.

Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Add signature)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

disk: efi: ignore 'IGNOREME' GPT header found on cros eMMCs

Some ChromeOS devices (atleast veyron speedy) have the first 8MiB of
the eMMC write protected and equipped with a dummy 'IGNOREME' GPT
header - instead of spewing error messages about it, just silently
try the backup GPT.

Note: this does not touch the gpt cmd writing/verifying functions,
those will still complain.

Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

disk: efi: unify code for finding a valid gpt

There were 3 copies of the same sequence, make it into a function.

Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

board: puma: Use rockchip_* helpers to setup cpuid and macaddr

We should use the shared helpers to setup the necessary parts

Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3399: Enable CONFIG_MISC_INIT_R for the Rock PI 4

This enables us to set a static MAC address

Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3399: derive ethaddr from cpuid

Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.

The MAC address is only generated and set if there is no ethaddr
present in the saved environment.

This is based off of Klaus Goger's work in 8adc9d

Signed-off-by: Rohan Garg <rohan.garg@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: remove fennec board support

Since there is no one using this board, remove it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3399: defconfig: remove SPL raw image support

RK3399 SPL only support FIT image for ATF bl31.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3368: defconfig: remove SPL raw image support

RK3368 SPL only support FIT image for ATF bl31.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3328: defconfig: remove SPL raw image support

RK3328 SPL only support FIT image for ATF bl31.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: Move config SYS_MALLOC_LEN to Kconfig

Use Kconfig for option SYS_MALLOC_LEN and default to 0x2000000.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: dts: rk3328-rock64: fix usb power supply

According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are
controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct
power supply for USB HOST ports.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3328: migrate u-boot node to -u-boot.dtsi

Move all the nodes only shown in u-boot to -u-boot.dtsi to make
rk3328.dtsi clean.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: dts: rk3328-rock64: enable usb3 xhci controller

Rock64 has a USB3.0 port, enable the controller so that we can use it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: clk: rk3328: add clk_enable ops for HCLK_HOST0

Required to successfully probe the ehci generic driver

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

ram: rk3399: update cap and ddrconfig for each channel after init

We need to store all the ram related cap/map info back to register
for each channel after all the init has been done in case some of register
was reset during the process.

Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq

- i2c dm model support of lx2160a, ls1088a, lx2088a, ls1028a
- icid setup for ls1028a, ls1088a
- other small fixes

armv8: ls1028a: add icid setup for platform devices

Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, edma, qdma, gpu, display and sec.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: ls1088a: add icid setup for platform devices

Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec. The ICID macros for SEC needed to be adapted because
the format of the registers is different.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: fsl-layerscape: make icid setup endianness aware

The current implementation assumes that the registers holding the ICIDs
are universally big endian. That's no longer the case on newer
platforms so update the code to take into account the endianness of
each register.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: fsl-layerscape: add base addresses for several devices

Add CCSR base addresses for ESDHC2, EDMA QDMA, DISPLAY and GPU devices.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: fsl-layerscape: add missing sec jr base address defines

Add defines for all the SEC job rings base addresses.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: kconfig: Fix some platforms incorrect I2C clock divider

By default, i2c input clock is platform clk / 2, but some of the
platform of i2c clock divider does not meet this kind of circumstance,
so alone to set default values for these platforms.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: ls1088aqds: support DSPI mode by hwconfig

BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used
to control SPI and other IP signal routing.

USBOSC:
0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz.
SPI devices are unusable in this mode.
1= SPI_CLK used as SPI clock.
SPI devices are usable in this mode. USB block is clocked from
internal sources

SPR[3:2]:
SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]):
00= SDHC/eMMC 8-bit
01= SD Card Rev 2.0/3.0
10= SPI on-board memory
11= TDM Riser / SPI off-board connector.
The default value is 00 if an SDCard/eMMC card is selected as the boot
device.

SPR[1:0]:
SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]):
00= SDHC Sync loop
01= TDM Riser / SPI off-board connector.
10= SPI on-board memory.
11= SPI off-board connector.

By default, the SPI feature is not available, so we need to configure
the above register fields to select the route to the SPI feature.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: ls1028aqds: define ARCH_MISC_INIT to handle mux

Define ARCH_MISC_INIT for LS1028AQDS platform to handle board
related mux.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: ls1046afrwy: Define CONFIG_ENV_ADDR for QSPI Boot

Defines CONFIG_ENV_ADDR for QSPI Boot which specifies the start
address of the flash sector containing the environment. It fixes
the issue that bootcmd is always set as default at bootup.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

boards: fsl: lx2160ardb: enable flexcan

Flexcan in LX2160ARDB is controlled by FPGA register boardcfg4
bit 5. enable this bit so that flexcan is enabled in LX2160ARDB.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

configs: ls1088a: Enable DM support for pcf2127 rtc

Enable related configs on all ls1088aqds boards to support pcf2127
rtc DM function.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls1088aqds : Add pcf2127 node

Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: ls1088aqds: Add support of I2C driver model.

Udate ls1088aqds board init code to support DM_I2C.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls1088ardb: Add slave nodes under the i2c0 controller

This patch adds some slave nodes to support the i2c dm on the device
side under the i2c0 controller.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls1088a: add I2C node support

One ls1088a, there are four I2C controllers. So add all I2C node
for ls1088a in device tree.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

gpio: do not include <asm/arch/gpio.h> on ARCH_LS1088A

As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1088a.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

boards: ls1088a: Add support of I2C driver model

DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1088a platform
does not support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

configs: ls2088a: Enable DM support for ds3231 rtc

Enable related configs on all ls2088aqds boards to support ds3231
rtc DM function.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls2088aqds : Add ds3232 node

Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds
boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

boards: ls2088aqds: Add support of I2C driver model.

Update ls2088aqds board init code to support DM_I2C.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

rtc: ds3232/ds3231: Add support to generate 32KHz output for driver module

Add an implementation of the rtc_enable_32khz_output() that uses the
driver model i2c APIs.

Also put code related to rtc_enable_32khz_output
under CONFIG_RTC_ENABLE_32KHZ_OUTPUT.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls2088ardb: Add slave nodes under the i2c0

Add some slave nodes to support the i2c dm on the device side under the i2c0.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: fsl-ls2088a: add i2c node support

One ls2088a, there are four I2C controllers. So add I2C nodes in dts
for ls2088a.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

gpio: do not include <asm/arch/gpio.h> on ARCH_LS2080A

As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2080a.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

boards: ls2088a: Add support of I2C driver model.

DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls2088a platform
does not support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls1028aqds: Add pcf2127 node under i2c1

Add the pcf2127-rtc node under the i2c1 in dts for ls1028aqds boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls1028aqds: Add pca9547 node under the i2c0 controller

Add pca9547 node to support i2c multiplexer under the i2c0 controller
in dts for ls1028aqds boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

configs: ls1028a: Enable DM support for pcf2127 rtc

Enable related configs on all ls1028aqds boards to support pcf2127
rtc DM function.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Tested-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: ls1028aqds: Remove the definition of CONFIG_SYS_I2C_EARLY_INIT

Since i2c uses dm mode, i2c controller will be initialized when reading
and writing devices on i2c bus. So there is no need for the original
non-dm mode i2c early initialization function call, this patch removed
the definition of CONFIG_SYS_I2C_EARLY_INIT.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: ls1028ardb: Add slave nodes under the i2c0 controller

Add some slave nodes to support the i2c dm on the device side under the i2c0.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

gpio: do not include <asm/arch/gpio.h> on ARCH_LS1028A

As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls1028a.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

boards: ls1028a: Add support of I2C driver model

DM_I2C_COMPAT is a compatibility layer that allows using the non-DM
I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch
solves the problem that the i2c-related api of the ls1028a platform
does not support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

configs: lx2160: enable DM support for pcf2127 rtc

Enable related configs on all lx2160ardb boards to support pcf2127
rtc DM feature.

Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from
Kconfig.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: lx2160aqds : Add pcf2127 node

Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for
lx2160aqds boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: lx2160ardb : Add the "u-boot, dm-pre-reloc" for i2c0

Lx2160ardb need to use i2c0 before relocation, so we also need to set
u-boot, dm-pre-reloc to initialize node before relocation.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: Add pcf2127 node for lx2160ardb

Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: dts: fsl-lx2160a: add i2c controller and gpio DT nodes

In lx2160a soc, there are eight i2c controllers, this patch adds i2c
nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller
depends.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

gpio: do not include <asm/arch/gpio.h> on ARCH_LX2160A

As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch ls2160a.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

drivers: i2c: mxc: Fix compiler error when using i2c dm mode

I2C dm mode enablemenet causes below compilation errors:

In file included from include/config.h:8:0,
                 from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
 #  error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
    ^~~~~
In file included from include/config.h:8:0,
                 from include/common.h:20:
include/config_fallbacks.h:51:4: error: #error "Cannot define
CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
 #  error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used"
    ^~~~~

board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f':
board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration
of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'?
[-Wimplicit-function-declaration]
  i2c_early_init_f();
  ^~~~~~~~~~~~~~~~
  arch_early_init_r

 drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe':
  drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function
'enable_i2c_clk';
  did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration]
  ret = enable_i2c_clk(1, bus->seq);
        ^~~~~~~~~~~~~~
        enable_irq_wake

So fix these compilation errors.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

boards: lx2160a: Add support of I2C driver model

DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C
API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for
compilation, a compilation error will be generated. This patch solves
the problem that the i2c-related api of the lx2160a platform does not
support dm.

Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

configs: ls1043aqds: Move CONFIG_FSL_QSPI to defconfig

Move CONFIG_FSL_QSPI from header file to defconfigs,
consequently unset imply config(CONFIG_SPI_FLASH_BAR) which
is not valid for LS series.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

armv8: ls1028a: select BOARD_LATE_INIT config

Select BOARD_LATE_INIT for ls1028ardb and ls1028aqds targets
so that late init work can be done.

Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

common: qixis: make the qixis compatible with new soc

This driver needs modification to work with new soc,
like ls1028, since bitmap of RCFG is changed to
RESV[7:5] LIVE[4] WDEN[3] RESV[2:1] GO[0]
   000      1       0        00      0

Also the RCW location is moved to only dutcfg0.
RESV[7:4] RCWSRC[3:0]
   1111   configurable

Following commands are functional now
qixis_reset
qixis_reset sd
qixis_reset qspi
qixis_reset emmc

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

drivers: net: mc: Report extra memory to Linux

MC firmware need to be aligned to 512M, so minimum 512MB DDR is reserved.
But MC support to work with 128MB or 256MB DDR memory also, in this
case, rest of the memory is not usable.
So reporting this extra memory to Linux through dtb memory fixup.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

clk: imx: add i.MX8MM clk driver

Add i.MX8MM clk driver support.

Signed-off-by: Peng Fan <peng.fan@nxp.com>

clk: imx: add i.MX8M composite clk support

Import i.MX8M composite clk from Linux Kernel 5.3.0-rc2

Signed-off-by: Peng Fan <peng.fan@nxp.com>

clk: imx: add pll14xx driver

Add pll14xx driver for i.MX8MM usage, modifed
from Linux Kernel 5.3.0-rc1

Signed-off-by: Peng Fan <peng.fan@nxp.com>

clk: imx: expose CCF entry for all

Expose CCF entry, then we could avoid expand the SoC support list

Signed-off-by: Peng Fan <peng.fan@nxp.com>

sandbox: clk: add clk enable/disable test code

Since we added clk enable_count and prograte clk child enabling
operation to clk parent, so add a new function sandbox_clk_enable_count
to get enable_count for test usage.

And add test code to get the enable_count after we enable/disable
the device clk.

Signed-off-by: Peng Fan <peng.fan@nxp.com>

clk: support clk tree dump

The previous code only dump the clk list. This patch is
to support clk tree dump, and also dump the enable_cnt.

The code used in patch is similar to dm_dump_all, but
the code here only filter out the UCLASS_CLK devices.

On i.MX8MM, Partial output:
u-boot=> clk dump
 Rate               Usecnt      Name
------------------------------------------
 24000000             0        |-- clock-osc-24m
 24000000             0        |   |-- dram_pll_ref_sel
 750000000            0        |   |   `-- dram_pll
 750000000            0        |   |       `-- dram_pll_bypass
 750000000            0        |   |           `-- dram_pll_out
 24000000             0        |   |-- arm_pll_ref_sel
 1200000000           0        |   |   `-- arm_pll
 1200000000           0        |   |       `-- arm_pll_bypass
 1200000000           0        |   |           `-- arm_pll_out
 1200000000           0        |   |               `-- arm_a53_src
 1200000000           0        |   |                   `-- arm_a53_cg
 1200000000           0        |   |                       `-- arm_a53_div
 24000000             4        |   |-- sys_pll1_ref_sel
 800000000            4        |   |   `-- sys_pll1
 800000000            4        |   |       `-- sys_pll1_bypass
 800000000            4        |   |           `-- sys_pll1_out
 40000000             0        |   |               |-- sys_pll1_40m

Signed-off-by: Peng Fan <peng.fan@nxp.com>